Numerical simulation of the sedimentation of cylindrical pollutant particles in fluid

The sedimentation of cylindrical pollutant particles which fall through a fluid is investigated. Differing from previous research work,particle oscillation and effect of particle on the fluid are considered, and the torque exerted on a particle when viscous fluid flow around a particle is got through experiment and included in the numerical simulation. The computational results showed that the sedimentation velocities of particle increase slowly with the increase of particle aspect ratio 9. For disk-like particle, when the motion direction of particle is parallel to axis of particle, particle falls more slowly than the case of perpendicular to axis of particle; while for rod-like particle, it is inverse. For sedimentation of a crowd of high-frequency oscillating cylindrical particles with arbitrary initial orientation, both vertical velocity and horizontal velocity oscillate dramatically, the degree of oscillation of the former is stronger than the later. A crowd of particles fall more quickly than an isolated particle. Particles tend to strongly align in the direction of gravity. The computational results agreed well with the experimental ones and helpful for controlling of pollutant particles.     

Direct numerical simulation of the motion of circular pollutant particles in Newtonian fluid

An improved implementation of distributed multiplier/fictitious domain method is presented for the direct numerical simulation of particulate flow. The key improvement is to replace a finite-element triangulation for the velocity and a “twice-coarser“ triangulation for the pressure with a rectangular discretization for the velocity and pressure. For code validation, the sedimentation of a single particle in a twodimensional channel was simulated. The results showed that the simulation is independent of the mesh size as well as the time step. The comparison between experimental data and this simulation showed that our code can give a more accurate simulation on the motion of particlesthan previous DLM code. The code was then applied to simulate the sedimentation of 600 particles in a rectangular box. The falling course ispresented and discussed. At the same time, this simulation also demonstrates that the method presented in this paper can be used for solving the initial problems involving a lager number of particles exaclly with computing durations kept at acceptable levels.     

滇池流域富磷地区暴雨径流中磷素的沉降及输移规律

滇池流域的磷矿分布及其开采是导致滇池湖泊富营养化的重要原因.因此,本文对滇池流域富磷地区暴雨径流中磷素输出、输移过程中总磷含量与颗粒粒径的关系进行了研究.结果发现,不同土地利用类型的污染源在暴雨中的磷流失量差异性显著,呈现磷矿开采区>林地>台地的特征;暴雨径流水样沉淀8h后,TP浓度显著下降;两场暴雨径流水样中,平均63.3%的磷素随粒径<0.02mm的颗粒流失,其中,平均43.8%的磷素随粒径<0.008mm的颗粒流失;两场暴雨径流中,仅有1.5%的总磷从污染源经沟渠最终进入了河道.研究表明,径流中所含总磷以小于0.02mm的颗粒物形式流失,通过延长水力停留时间可以达到良好的沉淀去除效果,而沟渠系统在面源总磷污染的控制过程中起着重要作用.     

明渠中有机质微粒沉降过程的随机游走模拟

基于明渠流动的主要特点,考虑紊动强度的垂向非均匀性,及颗粒运动的游荡效应（loitering effect）影响,对微粒运动基本方程进行改进,建立了明渠非均匀紊流中考虑游荡效应的随机游走模型,对明渠中微粒的沉降损失进行了模拟分析.模拟结果显示,不考虑游荡效应影响时,明渠中微粒的沉降损失率可用微粒沉速与水深之比计算;而在游荡效应影响下,微粒沉降损失率会发生约18%~27%的下降,下降百分比与均匀紊流中微粒沉速在游荡效应影响下的折减百分比渐近值（19~25%）基本一致.本文结论基于不考虑微粒重悬浮、游荡效应为紊流对微粒沉降的主导影响机理等前提,主要适用于对明渠中细小有机质微粒沉降至床底过程更准确的计算分析.     

明渠中有机质微粒沉降过程的随机游走模拟

基于明渠流动的主要特点,考虑紊动强度的垂向非均匀性,及颗粒运动的游荡效应（loitering effect）影响,对微粒运动基本方程进行改进,建立了明渠非均匀紊流中考虑游荡效应的随机游走模型,对明渠中微粒的沉降损失进行了模拟分析.模拟结果显示,不考虑游荡效应影响时,明渠中微粒的沉降损失率可用微粒沉速与水深之比计算;而在游荡效应影响下,微粒沉降损失率会发生约18%~27%的下降,下降百分比与均匀紊流中微粒沉速在游荡效应影响下的折减百分比渐近值（19~25%）基本一致.本文结论基于不考虑微粒重悬浮、游荡效应为紊流对微粒沉降的主导影响机理等前提,主要适用于对明渠中细小有机质微粒沉降至床底过程更准确的计算分析.     

不同品质燃油对公交车道路颗粒排放特征的影响

以国Ⅳ排放柴油公交车为样车,研究了3种燃油公交车的颗粒数量排放特性. 3种燃油分别为纯柴油、B20燃油〔V(生物柴油)∶V(纯柴油)=2∶8〕和G20燃油〔V(天然气制油)∶V(纯柴油)=2∶8〕. 结果表明:公交车燃用3种燃油的排气颗粒数量随粒径变化均呈双峰对数分布,其中核态颗粒数量峰值粒径均为10.8 nm;聚集态颗粒数量峰值粒径则因燃料差异而不同,其中纯柴油、B20燃油和G20燃油分别为80.6、69.8和60.4 nm. 对于不同类型道路,在公交车燃用纯柴油时,其快速路下的排气颗粒数量(7.35×1015 km-1)最低,分别比主干道和次干道低47.7%和55.1%. 对于不同品质燃油而言,在全程测试线路内,燃用G20燃油的公交车排气颗粒总数量(6.92×1015 km-1)最低,较纯柴油和B20燃油分别降低了42.5%和32.4%. 其中,G20燃油排气中核态颗粒数量为1.81×1015 km-1,较纯柴油和B20燃油分别降低了3.1%和15.4%,而聚集态颗粒数量则分别降低了49.7%和37.0%. 表明公交车燃用天然气制油可有效降低颗粒排放.      

金盆水库沉积物磷的来源及分布特征

为探究分层型水源水库沉积物中磷的来源与分布特征,以西安金盆水库为对象,针对2017年3～11月金盆水库水体、沉降颗粒及沉积物柱状样品总磷(TP)含量及形态分布特征进行研究.结果表明,金盆水库主库区表层沉积物总磷含量及形态分布受水体颗粒磷(PP)沉降作用明显,相关系数r~2=0. 877 5;同时表层沉积物总磷含量还受到沉积物内部生物地球化学的共同作用. 6～8月金盆水库水体藻类剧烈繁殖演替,繁殖过程中大量失去活性、死亡的藻类不断向底部水体沉积,形成以藻类等颗粒磷为主导的内源污染,沉降颗粒总磷含量达(753. 51±17. 11) mg·kg~(-1),表层沉积物总磷含量随之增加,以铁铝结合态非活性磷(NaOH-nrP)为主; 9～11月进入汛期,径流水体携带大量泥沙等负荷较大的污染物汇入水库,使得水体颗粒磷浓度相应增大,然而由于单位质量泥沙中总磷含量占比较小,导致径流过程中表层沉积物总磷含量逐渐降低,泥沙径流过程中颗粒磷以无机态的钙磷(Ca-P)和残渣态磷(rest-P)为主,二者约占沉积物总磷(TP) 55. 8%～66. 2%,受颗粒沉降影响相对较大.活性磷(SRP)、铁锰螯合态磷(BD-P)和铁铝结合态活性磷(NaOH-srP)这3种形态磷较活跃,在环境条件的变化(主要是氧化还原条件)下发生一系列迁移转化,受沉积物内部生物地球生物化学过程作用明显.     

颗粒物对紫外线灭活二级出水中粪大肠菌的影响

用低压紫外线照射具有相同颗粒物粒径分布的一系列水样,把实验结果带入二重动力学模型进行计算,评价自然状态下颗粒物对粪大肠菌的保护作用. 结果表明,二级出水中的大部分粪大肠菌都与颗粒物交连在一起;在颗粒物<10⁵ C·mL^-1时,颗粒物的增加会明显降低紫外线对二级出水中粪大肠菌的灭活率,但当颗粒物>10⁵ C·mL^-1时,这种影响不明显.从二重动力学模型的计算结果来看,对于不同颗粒物浓度的水样,难灭活的微生物所占的比重很小且比较稳定,大多数与颗粒物结合的粪大肠菌都较易被紫外线灭活.     

高岭土和蒙脱土存在下nC60纳米颗粒稳定性研究

通过沉降实验研究了不同浓度高岭土和蒙脱土分别对富勒烯纳米颗粒（nC₆₀）稳定性的影响,利用沉降模型并结合zeta电位、粒径、SEM、TEM进行原因分析.单体系中nC₆₀的稳定性好,高岭土胶体稳定性差且随浓度增加而降低,蒙脱土胶体稳定性好且与浓度无明显关系.整体上,高岭土和蒙脱土可以降低nC₆₀的稳定性.随着高岭土浓度增加,nC₆₀稳定性显著降低;而蒙脱土对nC₆₀稳定性降低较小且与浓度无明显关系.结果表明,nC₆₀的稳定性由黏土控制,两种黏土在结构和比表面积上的差异,使它们对nC₆₀稳定性影响不同.模型分析表明,一阶沉降模型和修正的一阶沉降模型分别适用于高岭土和蒙脱土参与的胶体沉降过程.该研究可为评估nC₆₀对地下水环境的影响提供重要参考.     

南京冬季晴天及雾-霾天气纳米气溶胶粒子谱日变化比较

利用2017年12月南京气溶胶数浓度与气象参数资料,比较研究晴天及雾-霾天中10~1000nm纳米气溶胶粒子谱日变化规律及差异特征.结果表明,单峰谱型出现与污染加重有明显关系,分别出现在晴天午后、霾严重污染阶段和污染消散阶段、浓雾过程,峰值粒径分别为晴天（20~100nm）、霾天（27~144nm）和雾天（34~122nm）.3种天气条件下,晴天较强的太阳辐射和较低的湿度适合小粒子生成,核模态占比在晴天最高;霾天气象场适合爱根态粒子大量稳定存在,爱根态占比在霾天最高;雾天大量气溶胶吸湿增长,导致积聚态占比在雾天最高.在霾天污染物累积阶段,大量积聚态粒子对核模态、爱根态粒子的碰并增长作用抑制核模态、爱根态粒子生成,核模态和爱根态粒子浓度变化率为-91.0%和-62.5%,而积聚态为89.7%.浓雾过程对爱根态粒子清除作用最明显.     

南京冬季大气气溶胶粒子谱分布及其对能见度的影响

2009年11～12月采用宽范围气溶胶粒径谱仪（WPS）、自动气象站和能见度仪等高分辨率仪器对南京北郊气溶胶粒子的谱分布特征与气象因子的关系及其对大气能见度的影响进行研究.结果表明,数浓度谱呈双峰分布,主峰集中在0.04～0.1μm;质量浓度谱的2个主峰位于0.5～0.7μm和2.7μm左右;表面积谱的2个主峰分别位于...     

超滤工艺净化微污染原水的试验研究

采用混凝沉淀-超滤工艺对微污染原水进行试验,对组合工艺的除污染特性进行了研究。结果表明,组合工艺对浊度、颗粒物和藻类的去除效果非常好。出水浊度稳定在0.1NTU以下,水中粒径>2μm的颗粒数约19个/mL,藻类平均数量约为2.2×104个/L。在去除有机物方面,组合工艺对高锰酸盐指数、UV254和DOC的去除率分别为38.0%、15.2%和32.6%,其中对高锰酸盐指数的去除效果较为突出,出水高锰酸盐指数浓度为2.69~2.87mg/L。组合工艺去除的有机物是分子量大于3KD的大分子有机物,对小分子有机物去除效果不明显。其中,混凝沉淀主要去除了水中的疏水性有机物和亲水荷电有机物,超滤膜去除的有机物则以亲水中性有机物为主。在工艺运行期间,超滤膜的跨膜压差增加了约12.3%,跨膜压差的升高主要由被超滤膜吸附的小分子有机物产生。     

新疆农用拖拉机排放清单及特征研究

分别应用参数本土化的NON-ROAD模型和生态环境部发布的《非道路移动源大气污染物排放清单编制技术指南》估算了新疆1993—2018年农业生产用拖拉机PM₁₀、PM_2.5、HC、NO_x和CO等污染物排放清单.同时,结合NON-ROAD模型特性、排放清单和区域现状,从定量和定性2个维度剖析了2种排放清单编制方法的适应性和污染物排放演变态势.最后,基于3种不同方法对污染物排放的潜在影响因素进行分析.结果表明：①基于参数本土化的NON-ROAD模型在建立特定区域排放清单方面具有一定参考价值.②1993—2018年新疆农用拖拉机污染物排放呈现出平稳上升、波动、快速增长、平稳、下降等不同态势,总体上,1993—2017年污染物排放增加25156.69 t,但在2018年出现较大幅度下降,同时单位功率排放也明显下降,表明近年来采取的强有力排放控制措施在抑制大气污染物排放方面的成效明显.③2006年之后大中型拖拉机年均排放总量占比为70.9%,小型拖拉机年均排放占比为29.1%,短期内随着时间的推移两者的差距将越来越大,揭示大中型拖拉机是污染物排放控制的关键.④对污染物排放影响因素的定量分析结果发现,农业经济发展水平对区域污染物排放总量变化起决定性作用.本研究在建立污染物排放清单、污染物排放影响因素定量分析及区域污染物排放治理政策制定方面有一定参考价值.     

集装箱焊接烟气治理工程实例分析

介绍了某集装箱厂焊接车间焊接烟尘收集、处理的工程实例,采用的工艺是集阻火过滤器、阻燃型纳米纤维滤筒、活性炭纤维过滤器为一体的多级过滤除尘设备。系统总处理风量98000m3/h,处理前车间内空气主要污染物颗粒物浓度达到7.8～10.5mg/m3。处理后车间内空气质量明显好转,颗粒物的浓度降低到2.56mg/m3以下,达到《工作场所有害因素职业接触限值》要求;经处理后污染物最终排放浓度均低于92mg/m3,满足《广东省地方标准大气污染物排放限值》第二时段二级标准要求。     

Ultrafine particle emission characteristics of diesel engine by on-board and test bench measurement

This study investigated the emission characteristics of ultrafine particles based on test bench and on-board measurements. The bench test results showed the ultrafine particle number concentration of the diesel engine to be in the range of (0.56-8.35) × 10⁸ cm^-3. The on-board measurement results illustrated that the ultrafine particles were strongly correlated with changes in real-world driving cycles. The particle number concentration was down to 2.0 × 10⁶ cm^-3 and 2.7 × 10⁷ cm^-3 under decelerating and idling operations and as high as 5.0 × 10⁸ cm^-3 under accelerating operation. It was also indicated that the particle number measured by the two methods increased with the growth of engine load at each engine speed in both cases. The particle number presented a "U" shaped distribution with changing speed at high engine load conditions, which implies that the particle number will reach its lowest level at medium engine speeds. The particle sizes of both measurements showed single mode distributions. The peak of particle size was located at about 50-80 nm in the accumulation mode particle range. Nucleation mode particles will significantly increase at low engine load operations like idling and decelerating caused by the high concentration of unburned organic compounds.     

室内打印机颗粒污染物特性的测量与分析

文章对打印机工作所产生的可吸人颗粒污染物进行研究,使用FMPS3091对5.6～560nm粒径范围的颗粒物进行数量浓度、质量浓度测量;使用分形理论对所产生的空气污染特性进行分析,并通过粒度的分形维数对其进行了定量表达.测量和分析的结果显示:打印机工作所产生颗粒物的数量浓度、质量浓度远远大手背景浓度,并随打印机工作时间增...     

北京市得田沟和崎峰茶金矿周边土壤中重金属的粒径分布特征

以北京市得田沟和崎峰茶金矿周边土壤为研究对象,运用斯托克斯沉降法研究土壤颗粒组成及重金属在不同粒径中的分布特征.结果表明,土壤颗粒主要以0.15 mm粒级为主,含量达到51.19%~79.75%,其次为0.15~0.05 mm粒级土壤,含量为14.67%~38.99%,粒级0.05~0.01 mm土壤含量为0.18%~7.6%,粒级0.01 mm的土壤含量仅占1.71%~5.95%.除Ti和V外,其它金属元素的含量具有明显的粒级效应,随着土壤粒径的减小而增大,但大多数金属元素不在最细粒级上达到最大值,而是在0.002~0.001 mm粒级上最大.金属元素在不同粒级上的累积效应与粒级上的含量相一致,金属元素在较细粒级上的累积作用明显强于粗粒级.细粒级土壤含有较高的金属含量,对人类健康危害极大,应积极采取有效措施防止极细粒级土壤进入空气和水源.     

Single particle analysis of ambient aerosols in Shanghai during the World Exposition, 2010: two case studies

ATSI Model 3800 aerosol time-of-flight mass spectrometer (ATOFMS) was deployed for single-particle analysis in Shanghai during the World Exposition (EXPO), 2010. Measurements on two extreme cases: polluted day (1st May) and clean day (25th September) were compared to show how meteorological conditions affected the concentration and composition of ambient aerosols. Mass spectra of 90496 and 50407 particles were analyzed respectively during the two sampling periods. The ART-2a neural network algorithm was applied to sort the collected particles. Seven major classes of particles were obtained: dust, sea salt, industrial, biomass burning, organic carbon (OC), elementary carbon (EC), and NH₄-rich particles. Number concentration of ambient aerosols showed a strong anti-correlation with the boundary layer height variation. The external mixing states of aerosols were quite different during two sampling periods because of different air parcel trajectories. Number fraction of biomass burning particles (43.3%) during polluted episode was much higher than that (21.6%) of clean time. Air parcels from the East China Sea on clean day diluted local pollutant concentration and increased the portion of sea salt particle dramatically (13.3%). The large contribution of biomass burning particles in both cases might be an indication of a constant regional background of biomass burning emission. Mass spectrum analysis showed that chemical compositions and internal mixing states of almost all the particle types were more complicate during polluted episode compared with those observed in clean time. Strong nitrate signals in the mass spectra suggested that most of the particles collected on polluted day had gone through some aging processes before reaching the sampling site.     

Drinking water biotic safety of particles and bacteria attached to fines in activated carbon process

In this paper, the drinking water biotic safety of particles and bacteria attached to fines in activated carbon process was investigated by actual treatment process and advanced treatment pilot trial with granular activated carbon. In the experiment, the particles were detected by IBR particle calculating instrument, the activated carbon fines were counted on the basis of the most probable number (MPN) with a microscope, the total number of bacteria was analyzed between the conventional agar culture medium and the one with R2A, and the bacteria attached to activated carbon fines was resolved by the homogenization technique. The experimental results showed that the average total number of particles was 205 CNT/mL in the activated carbon effluent during a filter cycle, of which the number of particles with sizes > 2 μm was 77 CNT/mL more than the present particle control criterion of the American drinking water product standard (50 CNT/mL). The backwash of low density and long duration lowered particle number in the effluent. The MPN of activated carbon fines in the effluent was between 400 and 600 CNT/L, which accounted for less than 5‰ of the total particles from activated carbon filtration for a poor relative level (R ² = 0.34). The microorganisms in activated carbon effluent consisted mostly of heterotrophic bacillus and the total bacteria number was five times as high as that of the inflow, i.e. the effluent from sand filter. The actual bacteria number may be truly indicated by the detection technique with R2A culture medium compared with the traditional agar cultivation. The inactivation efficiency of bacteria attached to activated carbon fines was less than 40% under 1.1 mg/L of chlorine contacting for 40 min. Results showed that the particles and bacteria attached to activated carbon fines may influence drinking water biotic safety, and that the effective control measures need to be further investigated.     

南京江北新区大气单颗粒来源解析及混合状态

利用单颗粒气溶胶飞行时间质谱（SPAMS）于2015年12月1~31日对南京江北新区大气单颗粒进行了测量,共采集到同时含有正负离子谱图的颗粒747.8万个.结果表明,监测期间南京江北新区总体空气质量较差,污染天气占比为49.2%,SPAMS所捕获的颗粒数与PM_2.5质量浓度的相关性达到0.83,因此颗粒物数浓度在一定程度上能够用来反映大气污染状况,监测点主要污染源包括燃煤源以及机动车尾气源,工业工艺源污染占比居第3位,3种源的总贡献率达到63.5%.从整体上看,PM_2.5质量浓度的升高大多伴随着燃煤及机动车尾气占比的升高,EC、混合碳（ECOC）与OC在生物质燃烧、扬尘、汽车尾气排放、燃煤燃烧以及工业源中均与NO₂^-、NO₃^-以及SO₄^-有较高的混合程度.