Catalytic activity of cerium-doped Ru/Al2O3 during ozonation of dimethyl phthalate

In this paper, factors influencing the mineralization of dimethyl phthalate (DMP) during catalytic ozonation with a cerium-doped Ru/Al₂O₃ catalyst were studied. The catalytic contribution was calculated through the results of a comparison experiment. It showed that doping cerium significantly enhanced catalytic activity. The total organic carbon (TOC) removal over the doped catalyst at 100 min reached 75.1%, 61.3% using Ru/Al₂O₃ catalyst and only 14.0% using ozone alone. Catalytic activity reached the maximum when 0.2% of ruthenium and 1.0% of cerium were simultaneously loaded onto Al₂O₃ support. Results of experiments on oxidation by ozone alone, adsorption of the catalyst, Ce ion’s and heterogeneous catalytic ozonation confirmed that the contribution of heterogeneous catalytic ozonation was about 50%, which showed the obvious effect of Ru-Ce/Al₂O₃ on catalytic activity. __________ Translated from China Environmental Science, 2006, 26(4): 445–448 [译自: 中国环境科学]     

催化臭氧氧化过程中溴酸盐的生成机制研究

以黄河下游某水厂滤后水为目标物,选择了9种催化剂,在间歇反应装置中研究了单独臭氧和催化臭氧氧化过程中溴酸盐（BrO 3-）的生成情况,结果表明,在催化臭氧氧化过程中,NiO、CuO、Fe3O4、Al2O3加入使BrO 3-质量分数分别降低34.0%、32.8%、29.2%、20.8%.选取Fe3 O4作为催化剂研究催化...     

Effect of Al2O3 doping on the structure and performance of an Al2O3/Fe2O3 catalyst for mercury oxidation

In this study,the thermal stability of a Fe_2 O_3 catalyst for mercury oxidation was significantly improved by doping with Al_2 O_3.After 1 hr,the catalyst doped with 10 wt.% Al_2 O_3 still exhibited a mercury conversion efficiency of 70.9%,while the undoped sample even lost its catalytic activity.Doping with Al_2 O_3 retarded the collapse of the catalyst mesoporous structure during high-temperature calcination,and the doped samples maintained a higher specific surface area,smaller pore size,and narrower pore size distribution.Transmission electron microscope images revealed that after calcination at 350℃,the average size of the catalyst grains in Fe_2 O_3 was 23.4 nm;however,the corresponding values for 1%Al_2 O_3/Fe_2 O_3,3%Al_2 O_3/Fe_2 O_3,and 10%Al_2 O_3/Fe_2 O_3 were only 13.3,7.1,and 4.7 nm,respectively.Results obtained from X-ray diffraction and thermogravimetry coupled with differential scanning calorimetry confirmed that doping with Al_2 O_3 also retards the crystallization of the catalysts at high temperature,constraining catalyst grains to a smaller size.     

铈掺杂Ru/Al2O3催化臭氧氧化降解邻苯二甲酸二甲酯

考察了铈(Ce)的掺杂对Ru/Al2O3催化臭氧氧化邻苯二甲酸二甲酯(DMP)溶液过程的影响.结果表明,Ce的掺杂可以显著提高臭氧氧化的效果,反应100min后,TOC的去除率可以由原催化剂的61.3%提高到75.1%,而单独臭氧氧化仅有14.0%.在实验范围内,Ru和Ce同时浸渍催化效果较好,且活性组分的溶出最少,Ce的最佳掺杂量为1.0%.通过催化剂吸附试验、单独臭氧氧化试验、Ce的均相催化试验及Ru-Se/Al2O3催化剂的非均相催化实验,证明Ru-Ce/Al2O3催化剂对DMP溶液臭氧氧化体系TOC的去除率达到50%,这是基于Ru-Ce/A12O3催化剂的非均相催化作用.     

人工智能助力臭氧催化剂SrFexZr1-xO3的开发

将人工智能应用于催化臭氧氧化催化剂SrFe_xZr_1-xO₃的开发过程,采用共沉淀法制备了50种不同配方的催化剂,考察聚乙二醇（PEG）投加量、煅烧时间、老化时间、氨水投加量和铁掺杂量对SrFe_xZr_1-xO₃催化剂催化臭氧降解间甲酚反应活性的影响.同时,利用人工神经网络（ANN）和响应面（RSM）对催化剂合成条件与TOC去除率和间甲酚转化率的关系进行拟合,训练集中ANN的R²值分别为0.91和0.97,高于RSM的R²值0.35和0.41;在4组测试集上ANN的均方误差（MSE）分别为9.87和17.67,远小于RSM的23.89和28.87.结果表明,ANN模型对催化剂制备过程的复杂体系具有更好的拟合和泛化能力.在ANN训练好的模型中通过枚举法寻找最优合成条件为：PEG投加量为19.00%,煅烧时间为1.25 h,老化时间为26.50 h,氨水投加量为6.21 mL,铁掺杂量为3.37%,所得催化剂为SrFe_0.13Zr_0.87O₃-B.最佳反应条件下,间甲酚转化率和TOC去除率分别达到98.52%和17.21%,优于空白组的73.46%和1.86%.     

Decrease of NH4+-N by bacterioplankton accelerated the removal of cyanobacterial blooms in aerated aquatic ecosystem

We used aerated systems to assess the influence of the bacterioplankton community on cyanobacterial blooms in algae/post-bloom of Lake Taihu, China. Bacterioplankton community diversity was evaluated by polymerase chain reaction-denaturing gradient gel electrophoresis(PCR-DGGE) fingerprinting. Chemical analysis and nitrogen dynamic changes illustrated that NH4+-N was nitrified to NO2-N and NO3-N by bacterioplankton. Finally, NH4+-N was exhausted and NO3-N was denitrified to NO2-N, while the accumulation of NO2-N indicated that bacterioplankton with completely aerobic denitrification ability were lacking in the water samples collected from Lake Taihu. We suggested that adding completely aerobic denitrification bacteria(to denitrify NO2-N to N2)would improve the water quality. PCR-DGGE and sequencing results showed that more than 1/3 of the bacterial species were associated with the removal of nitrogen, and Acidovorax temperans was the dominant one. PCR-DGGE, variation of nitrogen, removal efciencies of chlorophyll-a and canonical correspondence analysis indicated that the bacterioplankton significantly influenced the physiological and biochemical changes of cyanobacteria. Additionally, the unweighted pair-group method with arithmetic means revealed there was no obvious harm to the microecosystem from aeration. The present study demonstrated that bacterioplankton can play crucial roles in aerated ecosystems, which could control the impact of cyanobacterial blooms in eutrophicated fresh water systems.     

A comparative investigation of NdSrCu1-xCoxO4-σ and Sm1:8Ce0:2Cu1-xCoxO4-σ(x: 0-0.4) for NO decomposition

A series of single-phase T-structured NdSrCu1??xCoxO4?? with oxygen vacancies and T0-structured Sm1:8Ce0:2Cu1??xCoxO4?? (x: 0–0.4) with oxygen excess were prepared using ultrasound-assisted citric acid complexing method, and characterized by means of techniques such as thermogravimetric analysis and NO temperature-programmed desorption (NO-TPD). The catalytic activities of these materials were evaluated for the decomposition of NO. It was found that the NdSrCu1??xCoxO4?? catalysts were of oxygen vacancies whereas the Sm1:8Ce0:2Cu1??xCoxO4?? ones possessed excessive oxygen (i.e., over-stoichiometric oxygen); with a rise in Co doping level, the oxygen vacancy density of NdSrCu1??xCoxO4?? decreased while the over-stoichiometric oxygen amount of Sm1:8Ce0:2Cu1??xCoxO4?? increased. The NO-TPD results revealed that NO could be activated much easier over the oxygen-deficient perovskite-like oxides than over the oxygen-excessive perovskite-like oxides, with the NdSrCuO3:702 catalyst showing the best e ciency in activating NO molecules. Under the conditions of 1.0% NO/helium, 2800 hr??1, and 600–900°C, the catalytic activity of NO decomposition followed the order of NdSrCuO3:702 > NdSrCu0:8Co0:2O3:736 > NdSrCu0:6Co0:4O3:789 > Sm1:8Ce0:2Cu0:6Co0:4O4:187 > Sm1:8Ce0:2Cu0:8Co0:2O4:104 > Sm1:8Ce0:2CuO4:045, in concord with the sequence of decreasing oxygen vacancy or oxygen excess density. Based on the results, we concluded that the higher oxygen vacancy density and the stronger Cu3+/Cu2+ redox ability of NdSrCu1??xCoxO4?? account for the easier activation of NO and consequently improve the catalytic activity of NO decomposition over the catalysts.     

纳米四氧化三铁对2,4-D的脱氯降解

采用纳米四氧化三铁(Fe3O4)降解水溶液中的2,4-二氯苯氧乙酸(2,4-D),考察了2,4-D初始浓度、纳米Fe3O4投加量、溶液pH和温度等因素对2,4-D降解率的影响.结果表明,纳米Fe3O4对2,4-D有显著的降解效果,初始浓度为10 mg/L的2,4-D, 48 h内降解率可达48%.纳米Fe3O4对2,4-D的降解是一个还原脱氯过程,反应体系中氯离子浓度随2,4-D浓度降低而升高.LC/MS分析表明,2,4-D降解的主要产物是苯酚,其他中间产物是2,4-二氯苯酚(2,4-DCP)、4-氯苯酚(4-CP)和2-氯苯酚(2-CP).溶液中2,4-D的降解符合准一级反应动力学,产物4-CP、2,4-DCP和苯酚的反应速率常数K分别为0.0043、0.0026和0.0032 h -1.环境条件对降解效率有显著影响,2,4-D初始浓度在0～10 mg/L、纳米Fe3O4投加量0～300 mg/L的范围内,2,4-D降解率随初始浓度和纳米Fe3O4投加量的增加而增大;pH对2,4-D的脱氯降解有显著影响,在pH为3.0时,纳米Fe3O4对2,4-D的还原脱氯效果最好;温度升高,可以提高脱氯反应速率.     

O3/UV降解水中的乙酸和硝基苯

利用O3 /UV和O3/H2O2降解了水中的乙酸,结果表明,在相同条件下处理60min后,O3/UV对乙酸的去除率仅比单独臭氧化处理提高了3%,而O3/H2O2在此条件下完全降解乙酸.O3/UV在处理硝基苯过程中却显示较好的氧化降解能力,通过分析表明,硝基苯降解过程中所产生的副产物H2O2对有机物的去除具有很重要的作用.因此,O3/UV氧化降解能力的提高可能有2方面的原因,紫外光对有机物的活化作用;中间产物H2O2催化臭氧分解产生了高活性的羟基自由基. 单独紫外光催化臭氧分解产生羟基自由基的效率极低.     

O3/H2O2氧化工艺去除水中硝基苯的研究

以硝基苯为代表性有机污染物 ,对比了臭氧化和O3/H2 O2 高级氧化工艺对水中硝基苯的去除效果 .发现与臭氧化相比 ,O3/H2 O2 高级氧化工艺可以显著地提高水中硝基苯的去除效率 .无论在臭氧化还是在O3/H2 O2 高级氧化工艺中 ,水中硝基苯的降解都主要是由OH·完成的 .通过考察O3/H2 O2 高级氧化工艺去除水中硝基苯的影响因素发现 ,在O3和过H2 O2 投量相同的条件下 ,多次投加O3和催化剂H2 O2 对水中硝基苯的处理效果明显优于一次性投加 ;在本次试验条件下 ,O3/H2 O2 高级氧化工艺降解蒸馏水和自来水中硝基苯的最优H2 O2 与O3摩尔比均为 0 5 ,HCO- 3碱度水平 (以CaCO3计 )在低于 1 0 0mg/L范围内对去除硝基苯无显著影响     

BiOCl/SiO2/Fe3O4复合材料可见光催化去除水中亚甲基蓝

以FeCl_3·6H_2O、FeCl_2·4H_2O、(C_2H_5)_4SiO_4、Bi(NO_3)_3·5H_2O、KCl为主要原料,采用化学共沉淀法和水热法制备了BiOCl/SiO_2/Fe_3O_4光催化剂,并对其进行EDS、TEM、XRD、FT-IR、UV-Vis表征,最后通过亚甲基蓝降解实验,研究了催化剂在合成过程中pH及催化剂投加量对其光催化性能的影响.结果表明,在pH=6、催化剂初始投加量为0.5 g·L~(-1)时,对亚甲基蓝的可见光催化效果最佳,光照120 min后对10 mg·L~(-1)的亚甲基蓝溶液的脱色率达到93.2%.BiOCl/SiO_2/Fe_3O_4经过简单的无水乙醇和水洗后,可高效重复利用4次.综合表明,BiOCl/SiO_2/Fe_3O_4是一种在处理染料废水中具有应用前景的磁性光催化剂.     

纳米Fe3O4/H2O2降解诺氟沙星

采用纳米Fe3O4催化H2O2氧化降解水环境中的诺氟沙星.考察了溶液酸度、温度、催化剂和H2O2浓度对诺氟沙星降解的影响,对比不同底物在Fe3O4/H2O2体系中的降解情况,并进一步探讨了其反应机制.结果表明,溶液酸度显著影响诺氟沙星的降解率,在酸性条件下（pH=3.5）诺氟沙星的降解效率最高.诺氟沙星的降解率随纳米F...     

Enhanced dechlorination of 2,4-dichlorophenol by recoverable Ni/Fe–Fe3O4 nanocomposites

Ni/Fe-Fe_3O_4 nanocomposites were synthesized for dechlorination of 2,4-dichlorophenol(2,4-DCP). The effects of the Ni content in Ni/Fe-Fe_3O_4 nanocomposites, solution pH, and common dissolved ions on the dechlorination efficiency were investigated, in addition to the reusability of the nanocomposites. The results showed that increasing content of Ni in Ni/Fe–Fe_3O_4 nanocomposites, from 1 to 5 wt.%, greatly increased the dechlorination efficiency; the Ni/Fe–Fe_3O_4 nanocomposites had much higher dechlorination efficiency than bare Ni/Fe nanoparticles. Ni content of 5 wt.% and initial p H below 6.0 was found to be the optimal conditions for the catalytic dechlorination of 2,4-DCP. Both 2,4-DCP and the intermediate product 2-chlorophenol(2-CP) were completely removed, and the concentration of the final product phenol was close to the theoretical phenol production from complete dechlorination of 20 mg/L of 2,4-DCP, after 3 hr reaction at initial p H value of 6.0,3 g/L Ni/Fe-Fe_3O_4 , 5 wt.% Ni content in the composite, and temperature of 22℃. 2,4-DCP dechlorination was enhanced by Cl-and inhibited by NO3-and SO_4~(2-). The nanocomposites were easily separated from the solution by an applied magnetic field. When the catalyst was reused, the removal efficiency of 2,4-DCP was almost 100% for the first seven uses, and gradually decreased to 75% in cycles 8–10. Therefore, the Ni/Fe–Fe_3O_4 nanocomposites can be considered as a potentially effective tool for remediation of pollution by 2,4-DCP.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

不同硅铝比Fe-ZSM-5催化剂对氧化亚氮催化分解性能的研究

以不同硅铝比的H-ZSM-5分子筛为载体,采用离子交换法和化学气相沉积法制备Fe-ZSM-5催化剂,并用XRD、BET、TEM、UV-vis和NH3-TPD等表征手段对催化剂进行分析,研究催化剂中铁的存在状态.结果表明,分子筛的硅铝比影响铁在分子筛中的分布形态,化学气相沉积法和热离子交换法制得硅铝比为25的Fe-ZSM-5-25分子筛催化剂上均匀地分布着粒径为8 nm左右的纳米氧化铁颗粒,并且Fe-ZSM-5-25分子筛催化剂比Fe-ZSM-5-300更容易形成Fe3+x O y团簇.制得的Fe-ZSM-5分子筛催化剂催化分解氧化亚氮(N2O),结果表明,相同的制备方法,硅铝比小的Fe-ZSM-5-25催化剂对N2O分解活性更好;相同硅铝比的Fe-ZSM-5催化剂,采用化学气相沉积法制得的对N2O分解活性最好.另外,O2的存在对Fe-ZSM-5上N2O催化分解活性有抑制作用,而NO对N2O催化分解活性展示了一定的正效应.最后,经过100 h的连续反应,Fe-ZSM-5催化剂依然能够保持催化活性.     

One-step preparation of a novel graphitic biochar/Cu0/Fe3O4 composite using CO2-ambiance pyrolysis to activate peroxydisulfate for dye degradation

Herein,a one-step co-pyrolysis protocol was adopted for the first time to prepare a novel pyrogenic carbon-Cu⁰/Fe₃O₄ heteroatoms (FCBC) in CO₂ ambiance to discern the roles of each component in PDS activation.During co-pyrolysis,CO₂ catalyzed formation of reducing gases by biomass which facilitated reductive transformation of Fe³⁺ and Cu²⁺ to Cu⁰ and Fe₃O₄,respectively.According to the a...     

纳米Fe3O4/CeO2-H2O2非均相类Fenton体系对3,4-二氯三氟甲苯的降解

以浸渍法制备的新型纳米Fe3O4/Ce O2为催化剂,3,4-二氯三氟甲苯(3,4-DCBTE)为目标污染物,在Fe3O4/Ce O2-H2O2非均相类Fenton体系中对目标污染物的降解进行研究,考察催化剂的催化效果和温度、p H、H2O2投加量等因素对催化剂催化效果的影响.结果表明,以纳米Fe3O4/Ce O2作为催化剂的非均相类Fenton体系对3,4-二氯三氟甲苯的处理效果极佳;随着温度的升高,纳米Fe3O4/Ce O2的催化效果不断提高;在偏酸性环境中,p H越低催化效果越好,p H=2时反应去除效率可达96.67%;随着H2O2投加量的增加,3,4-二氯三氟甲苯的降解效率先提高后降低,投加量为15 mg·L-1时去除效果最好可达99.47%;随着催化剂投加量的增加,同样出现了处理效果先升高后降低的现象,投加量为0.5 g·L-1时催化效果最好可达99.64%.在以纳米Fe3O4/Ce O2为催化剂的非均相类Fenton体系中,3,4-二氯三氟甲苯的降解符合一级反应动力学,反应所需活化能较低只需30.26 k J·mol-1.     

Effect of pretreatment on Pd/Al2O3 catalyst for catalytic oxidation of o-xylene at low temperature

The effect of pretreatment on Pd/Al₂O₃ catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al₂O₃ catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al₂O₃ activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al₂O₃ pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al₂O₃, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al₂O₃ catalyst for the catalytic oxidation of o-xylene at low temperature.     

活性炭的表面性质对CeOx/AC催化臭氧氧化水中苯甲酸的影响机制

实验对活性炭(activated carbon,AC)进行了氧改性、氮改性、硫改性和氮-硫共改性,考查AC的表面性质对CeO_x/AC催化臭氧氧化苯甲酸性能的影响.结果表明,相比氧改性活性炭ACO、硫改性活性炭ACS和氮改性活性炭ACN,氮-硫共改性活性炭ACNS由于含氮官能团和含硫官能团的引入,提高了对苯甲酸的吸附性能和催化臭氧氧化性能.采用氮-硫共改性活性炭为载体制备的CeO_x/ACNS催化剂表面Ce~(3+)含量最高,因而具有最高的催化活性,反应30 min,苯甲酸的去除率由单独臭氧氧化的22%提高到88%,TOC的去除率单独臭氧氧化的7%提高到55%.CeO_x/ACNS催化剂具有良好的稳定性,循环使用6次,苯甲酸的去除率仅从88%降低到82%,整个过程中活性组分Ce的流失只占负载量的0.32%,是一种很有应用潜力的臭氧氧化催化剂.     

Fe2O3/TiO2负载膨胀珍珠岩光催化降解罗丹明B

为获得高效催化活性的光催化材料,研究不同煅烧氛围对材料在可见光下催化性能的影响,以膨胀珍珠岩（EP）为载体,采用溶胶-凝胶法,在不同煅烧氛围（O₂和/或NH₃）下制备Fe₂O₃/TiO₂负载EP的光催化复合材料〔Fe₂O₃-TEP（O₂）、Fe₂O₃-TEP（NH₃）、Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）〕,采用EDS（X-射线色散能谱）、BET（比表面积及孔径分析）、XRD（X射线衍射）、SEM（扫描电子显微镜）、XPS（X射线光电子能谱）等对复合材料进行表征,并研究了其在可见光下对罗丹明B的光催化降解效果.结果表明:①复合材料成功负载了Ti、Fe元素,负载的TiO₂以锐钛矿型存在,Fe₂O₃的掺杂增强了TiO₂对可见光的响应能力;②不同的煅烧氛围明显影响复合材料的晶粒尺寸、比表面积和光催化性能,其中,Fe₂O₃-TEP（O₂,NH₃）的光催化性能最好,4 h后罗丹明B降解率达到87.59%,Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）4 h后对罗丹明B的降解率则分别为65.02%、62.48%和47.48%;③在试验条件下,复合材料的光催化反应符合一阶反应动力学方程,Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）相应的降解速率常数分别为0.008 3、0.004 3、0.004 3和0.002 7 min-1.研究显示,通过溶胶-凝胶法所制备的复合材料（Fe₂O₃-TEP）经煅烧后所得矿相均一;Fe₂O₃掺杂TiO₂可形成Ti—O—Fe键,减小TiO₂固有的禁带宽度;复合材料光催化性能也受到煅烧氛围的影响,先O₂后NH₃煅烧条件下所得材料的光催化性能最佳.