铈掺杂Ru/Al2O3催化臭氧氧化降解邻苯二甲酸二甲酯

考察了铈(Ce)的掺杂对Ru/Al2O3催化臭氧氧化邻苯二甲酸二甲酯(DMP)溶液过程的影响.结果表明,Ce的掺杂可以显著提高臭氧氧化的效果,反应100min后,TOC的去除率可以由原催化剂的61.3%提高到75.1%,而单独臭氧氧化仅有14.0%.在实验范围内,Ru和Ce同时浸渍催化效果较好,且活性组分的溶出最少,Ce的最佳掺杂量为1.0%.通过催化剂吸附试验、单独臭氧氧化试验、Ce的均相催化试验及Ru-Se/Al2O3催化剂的非均相催化实验,证明Ru-Ce/Al2O3催化剂对DMP溶液臭氧氧化体系TOC的去除率达到50%,这是基于Ru-Ce/A12O3催化剂的非均相催化作用.     

Cu-Al2O3中骨架铜类芬顿催化去除水中有机污染物

为解决传统铁基芬顿催化剂在水体通常酸碱(pH6)条件下活性低的问题,采用简单共沉淀法制备了Cu掺杂的Al_2O_3类芬顿催化剂.通过X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外可见(UV-vis)吸收光谱分析表明,Cu-Al_2O_3中铜掺杂的质量分数低于4.77%时,催化剂中铜主要以Cu~(2+)和Cu~+的形式共存于Al_2O_3的骨架结构中,形成Al—O—Cu键;过量的铜掺杂会导致外骨架铜物种如铜氧化物团簇的存在.以难降解有机污染物2-氯苯酚(2-chlorophenol,2-CP)和染料罗丹明B(Rhodamine B,Rh B)为目标污染物,对Cu-Al_2O_3的类芬顿催化性能进行了详细地研究.结果表明,骨架铜物种在中性温和条件下对2-CP和Rh B显示出很高的催化去除效率和稳定性,反应2 h,Cu-Al_2O_3(Cu质量分数4.77%)对2-CP的去除率达到54%,相应的TOC去除率达到49%,而铜离子溶出浓度仅为0.025 5 mg·L-1,而Cu-Al_2O_3(Cu质量分数7.58%)由于外骨架铜的存在导致催化活性增加缓慢和稳定性下降.ESR测试结果表明,·OH和HO_2~-/O_2~-·是反应中主要的活性物种.     

催化臭氧氧化过程中溴酸盐的生成机制研究

以黄河下游某水厂滤后水为目标物,选择了9种催化剂,在间歇反应装置中研究了单独臭氧和催化臭氧氧化过程中溴酸盐（BrO 3-）的生成情况,结果表明,在催化臭氧氧化过程中,NiO、CuO、Fe3O4、Al2O3加入使BrO 3-质量分数分别降低34.0%、32.8%、29.2%、20.8%.选取Fe3 O4作为催化剂研究催化...     

人工智能助力臭氧催化剂SrFexZr1-xO3的开发

将人工智能应用于催化臭氧氧化催化剂SrFe_xZr_1-xO₃的开发过程,采用共沉淀法制备了50种不同配方的催化剂,考察聚乙二醇（PEG）投加量、煅烧时间、老化时间、氨水投加量和铁掺杂量对SrFe_xZr_1-xO₃催化剂催化臭氧降解间甲酚反应活性的影响.同时,利用人工神经网络（ANN）和响应面（RSM）对催化剂合成条件与TOC去除率和间甲酚转化率的关系进行拟合,训练集中ANN的R²值分别为0.91和0.97,高于RSM的R²值0.35和0.41;在4组测试集上ANN的均方误差（MSE）分别为9.87和17.67,远小于RSM的23.89和28.87.结果表明,ANN模型对催化剂制备过程的复杂体系具有更好的拟合和泛化能力.在ANN训练好的模型中通过枚举法寻找最优合成条件为：PEG投加量为19.00%,煅烧时间为1.25 h,老化时间为26.50 h,氨水投加量为6.21 mL,铁掺杂量为3.37%,所得催化剂为SrFe_0.13Zr_0.87O₃-B.最佳反应条件下,间甲酚转化率和TOC去除率分别达到98.52%和17.21%,优于空白组的73.46%和1.86%.     

氮掺杂生物炭催化臭氧对于布洛芬的降解特性与机制

系统研究了新型氮掺杂生物炭材料(N-C)催化臭氧对于水中布洛芬(IBP)的氧化降解效能及机制,并深入探究了初始pH、臭氧投加量、催化剂投加量、不同阴离子和背景水质条件对IBP降解效率的影响.结果 表明,相较于一些常见的碳基催化剂(g-C3N4、生物炭、颗粒活性炭)及金属催化剂(MnO2、Fe3O4),N-C催化臭氧体系...     

Catalytic performance of Fe3O4-CoO/Al2O3 catalyst in ozonation of 2-(2,4-dichlorophenoxy)propionic acid, nitrobenzene and oxalic acid in water

Fe3O4-CoO/Al2O3 catalyst was prepared by incipient wetness impregnation using Fe(NO3) 3·9H2O and Co(NO3) 2·6H2O as the precursors,and its catalytic performance was investigated in ozonation of 2-(2,4-dichlorophenoxy) propionic acid(2,4-DP) ,nitrobenzene and oxalic acid.The experimental results indicated that Fe3O4-CoO/Al2O3 catalyst enabled an interesting improvement of ozonation eciency during the degradation of each organic pollutant,and the Fe3O4-CoO/Al2O3 catalytic ozonation system followed a radical-type mechanism.The kinetics of ozonation alone and Fe3O4-CoO/Al2O3 catalytic ozonation of three organic pollutants in aqueous solution were discussed under the mere consideration of direct ozone reaction and OH radical reaction to well investigate its performance.In the catalytic ozonation of 2,4-DP,the apparent reaction rate constants(k) were determined to be 1.456×10-2 min-1 for ozonation alone and 4.740×10-2 min-1 for O3/Fe3O4-CoO/Al2O3.And O3/Fe3O4-CoO/Al2O3 had a larger Rct(6.614×10-9) calculated by the relative method than O3 did(1.800×10-9) ,showing O3/Fe3O4-CoO/Al2O3 generated more hydroxyl radical.Similar results were also obtained in the catalytic ozonation of nitrobenzene and oxalic acid.The above results demonstrated that the catalytic performance of Fe3O4-CoO/Al2O3 in ozonation of studied organic substance was universal to a certain degree.     

Degradation of endocrine disruptor bisphenol A in drinking water by ozone oxidation

The ozone oxidation of endocrine disruptor bisphenol A in drinking water was investigated. A stainless completely mixed reactor was employed to carry out the degradation experiments by means of a batch model. With an initial concentration of 11.0 mg/L, the removal efficiencies of BPA (bisphenol A) could be measured up to 70%, 82%, and 90% when the dosages of ozone were 1, 1.5, and 2 mg/L, respectively. The impacts on BPA degradation under the conditions of different ozone dosages, water background values, BPA initial concentrations, and ozone adding time were analyzed. The results showed that ozone dosage plays a dominant role during the process of BPA degradation, while the impact of the contact time could be ignored. UV wavelength scanning was used to confirm that the by-products were produced, which could be absorbed at UV254. The value of UV254 was observed to have changed during the ozonation process. Based on the change of UV254, it could be concluded that BPA is not completely degraded at low ozone dosage, while shorter adding time of total ozone dosage, high ozone dosage, and improvement of dissolved ozone concentration greatly contribute to the extent of BPA degradation. The effects of applied H₂O₂ dose in ozone oxidation of BPA were also examined in this study. The O₃-H₂O₂ processes proved to have similar effects on the degradation of BPA by ozone oxidation. Translated from Environmental Science, 2006, 27(2): 294–299 [译自: 环境科学]     

Oxidation of diesel soot on binary oxide CuCr(Co)-based monoliths

Binary oxide systems (CuCr₂O₄, CuCo₂O₄), deposited onto cordierite monoliths of honeycomb structure with a second support (finely dispersed Al₂O₃), were prepared as filters for catalytic combustion of diesel soot using internal combustion engine's gas exhausts (O₂, NO_x, H₂O, CO₂) and O₃ as oxidizing agents. It is shown that the second support increases soot capacity of aforementioned filters, and causes dispersion of the particles of spinel phases as active components enhancing thereby catalyst activity and selectivity of soot combustion to CO₂. Oxidants used can be arranged with reference to decreasing their activity in a following series: O₃ ? NO₂ > H₂O > NO > O₂ > CO₂. Ozone proved to be the most efficient oxidizing agent: the diesel soot combustion by O₃ occurs intensively (in the presence of copper chromite based catalyst) even at closing to ambient temperatures. Results obtained give a basis for the conclusion that using a catalytic coating on soot filters in the form of aforementioned binary oxide systems and ozone as the initiator of the oxidation processes is a promising approach in solving the problem of comprehensive purification of automotive exhaust gases at relatively low temperatures, known as the “cold start” problem.     

MnFe2O4磁性纳米棒非均相Fenton催化降解水中四环素的研究

采用水热合成法成功制备出MnFe₂O₄磁性纳米棒（s-MnFe₂O₄）,并考察了商品化的Fe₃O₄、MnFe₂O₄和合成的s-MnFe₂O₄纳米棒这3种磁性纳米颗粒作为非均相Fenton催化剂降解水中四环素抗生素的性能.同时,采用X射线衍射（XRD）、透射电镜（TEM）、N₂吸附-脱附、振动样品磁强计（VSM）及X射线光电子能谱（XPS）等技术对催化剂的理化性质进行了表征.非均相Fenton催化降解四环素的结果表明,s-MnFe₂O₄具有最高的催化活性,反应180 min,四环素的去除率可以达到87.6%,TOC的去除率达到47.5%.自由基捕获试验证实了羟基自由基（·OH）是非均相Fenton氧化过程中的主要活性物种.s-MnFe₂O₄磁性纳米棒的高催化活性归因于其表面拥有较高含量的Mn³⁺和Fe²⁺物种,它们的存在能加速界面电子的转移效率,从而促进·OH的生成.合成的s-MnFe₂O₄催化剂具有良好的稳定性,循环使用6次,四环素的去除率仅从87.6%降低到80.2%,且氧化过程中活性组分的流失很少.     

Effect of CeO2 and Al2O3 on the activity of Pd/Co_3O_4/cordierite catalyst in the three-way catalysis reactions (CO/NO/CnHm)

The present article studies the effect of CeO₂ and Al₂O₃ on the activity of Pd/Co₃O₄/cordierite catalyst in conversion of NO, CO, C_nH_m. The catalysts were characterized by temperature programmed reduction with hydrogen, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. It is shown that the effect of CeO₂ on the properties of Pd/Co₃O₄/cordierite catalyst depends on preparation method. The catalyst obtained by co-deposition of cerium and cobalt oxides has higher activity in CO oxidation (CO + O₂ and CO + NO) and total hexane oxidation (C₆H₁₄ + O₂). Such phenomenon is probably caused by more than stoichiometric amount of formed oxygen vacancies, an increase in both mobility of surface oxygen and dispersity of components in the catalytic composition. It is demonstrated that CeO₂ addition promotes the SO₂ resistance of Pd/Co₃O₄/cordierite. The second support decreases the activity of Pd/Co₃O₄/cordierite catalyst in the reactions of CO and C₆H₁₄ with oxygen because of CoAl₂O₄ formation.     

有机酸在金属氧化物上的吸附对催化臭氧氧化的影响

以苯甲酸(BA)、邻苯二甲酸(PA)、商品腐殖酸(CHA)和反渗透法提取的松花江水腐殖酸(SHA)为目标物,研究了臭氧氧化及羟基氧化铁(FeOOH)和二氧化铈(CeO₂)为催化剂时的吸附与催化臭氧氧化去除这些有机物的效果.结果表明,BA在FeOOH表面没有吸附,FeOOH对BA催化氧化的去除率比臭氧单独氧化高45%;PA在FeOOH上的吸附使其溶液中的浓度减少了5%,此时FeOOH对PA的氧化没有催化作用.CeO₂有助于催化臭氧氧化在其表面吸附较强的PA,且对氧化产生的草酸根有催化去除作用,但对不吸附在其表面的BA没有催化臭氧氧化作用.CeO₂对腐殖酸的吸附比FeOOH强,其催化臭氧氧化去除腐殖酸的作用比FeOOH更显著;当无机阴离子和腐殖酸竞争金属氧化物表面的吸附位时,催化作用受到抑制.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

臭氧/纳米TiO2催化氧化去除水中微量硝基苯的研究

在悬浮颗粒搅拌混合反应器中,研究了臭氧/纳米TiO₂催化氧化去除水中微量硝基苯的性能,结果表明,纳米TiO₂催化臭氧化去除硝基苯较单独臭氧氧化有明显的提高,反应20min硝基苯的去除率提高了44%.实验中分别考察了纳米TiO₂热处理温度、催化剂投量、臭氧投量、硝基苯初始浓度、pH值对臭氧/纳米TiO₂催化氧化去除硝基苯的影响.发现550℃烧结得到的纳米TiO₂表现出最好的催化臭氧化活性,在较低的臭氧投量与催化剂用量条件下,硝基苯的去除率可达到56.57%;增大臭氧或者硝基苯的初始浓度,硝基苯的去除率随之提高;但是改变催化剂投量,硝基苯的去除效果几乎不受影响;中性或碱性pH环境利于纳米TiO₂催化臭氧化反应的进行.通过研究叔丁醇对纳米TiO₂催化臭氧化反应的影响,证明反应遵循羟基自由基(·OH)反应机理.     

Effect of pretreatment on Pd/Al2O3 catalyst for catalytic oxidation of o-xylene at low temperature

The effect of pretreatment on Pd/Al₂O₃ catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al₂O₃ catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al₂O₃ activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al₂O₃ pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al₂O₃, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al₂O₃ catalyst for the catalytic oxidation of o-xylene at low temperature.     

Oxidation of diesel soot on binary oxide CuCr(Co)-based monoliths

Binary oxide systems (CuCr₂O₄, CuCo₂O₄), deposited onto cordierite monoliths of honeycomb structure with a second support (finely dispersed Al₂O₃), were prepared as filters for catalytic combustion of diesel soot using internal combustion engine's gas exhausts (O₂, NO_x, H₂O, CO₂) and O³ as oxidizing agents. It is shown that the second support increases soot capacity of aforementioned filters, and causes dispersion of the particles of spinel phases as active components enhancing thereby catalyst activity and selectivity of soot combustion to CO₂. Oxidants used can be arranged with reference to decreasing their activity in a following series: O₃ >> NO₂ > H₂O > NO > O₂ > CO₂. Ozone proved to be the most efficient oxidizing agent: the diesel soot combustion by O₃ occurs intensively (in the presence of copper chromite based catalyst) even at closing to ambient temperatures. Results obtained give a basis for the conclusion that using a catalytic coating on soot filters in the form of aforementioned binary oxide systems and ozone as the initiator of the oxidation processes is a promising approach in solving the problem of comprehensive purification of automotive exhaust gases at relatively low temperatures, known as the "cold start" problem.     

Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

Effects of Ce on catalytic combustion of methane over Pd-Pt/Al2O3 catalyst

Activity and stability of 1%Pd-0.2%Pt/Al₂O₃ and 1%Pd-0.2%Pt/0.6%Ce/Al₂O₃ catalysts prepared by impregnation method for catalytic combustion of methane in air were investigated. The catalysts before and after reaction were characterized by BET, CO chemisorption, XRD and XPS techniques. Results showed that the presence of Ce significantly increased the activity and thermal stability of the Pd-Pt/Al₂O₃ catalyst towards methane combustion, which could be attributed to more highly-dispersed active PdO particles over the Pd-Pt/Ce/Al₂O₃ catalyst surface as well as the retarded sintering of PdO and the maintained oxidized state of surface Pd during the combustion process in the presence of Ce.     

纳米Fe3O4/CeO2-H2O2非均相类Fenton体系对3,4-二氯三氟甲苯的降解

以浸渍法制备的新型纳米Fe3O4/Ce O2为催化剂,3,4-二氯三氟甲苯(3,4-DCBTE)为目标污染物,在Fe3O4/Ce O2-H2O2非均相类Fenton体系中对目标污染物的降解进行研究,考察催化剂的催化效果和温度、p H、H2O2投加量等因素对催化剂催化效果的影响.结果表明,以纳米Fe3O4/Ce O2作为催化剂的非均相类Fenton体系对3,4-二氯三氟甲苯的处理效果极佳;随着温度的升高,纳米Fe3O4/Ce O2的催化效果不断提高;在偏酸性环境中,p H越低催化效果越好,p H=2时反应去除效率可达96.67%;随着H2O2投加量的增加,3,4-二氯三氟甲苯的降解效率先提高后降低,投加量为15 mg·L-1时去除效果最好可达99.47%;随着催化剂投加量的增加,同样出现了处理效果先升高后降低的现象,投加量为0.5 g·L-1时催化效果最好可达99.64%.在以纳米Fe3O4/Ce O2为催化剂的非均相类Fenton体系中,3,4-二氯三氟甲苯的降解符合一级反应动力学,反应所需活化能较低只需30.26 k J·mol-1.     

Ce-Mn/Al2O3-H2O2催化氧化皮革废水的研究

以浸渍法制备了Ce-Mn/Al_2O_3催化剂,研究该催化剂在H_2O_2非均相类Fenton体系中对皮革废水污染物的催化降解性能.在单因素试验的基础上,以COD去除率为响应值,采用Box-Behnken响应曲面法考察了催化剂投加量、H_2O_2投加量、初始pH、反应时间等4个因素之间的单独作用及交互作用,实验数据用Design-Expert 8.0.6软件进行处理,得到二次响应曲面模型.结果表明,4个独立变量对响应值的影响顺序如下:初始pHH_2O_2投加量催化剂投加量反应时间,数学模型拟合度高(R_(adj)~2=0.9349),利用该模型预测的最大COD去除率为78.86%,最佳反应条件为:催化剂投加量56.63 g·L~(-1),H_2O_2投加量315.15 mg·L~(-1),初始pH3.51,反应时间2 h,经实验验证COD去除率为80.94%,与模型预测值偏差2.08%.     

SO2对Ag/Al2O3催化剂上CH3OH还原NO性能的影响

用溶胶-凝胶混合法制备了Ag负载量为5%的Ag/A1₂O₃催化剂.研究了富氧条件下,SO₂对CH₃OH在催化剂上还原NO性能的影响.结果表明,反应气不含SO₂和H₂O时,NO还原活性温度较低,有显著量N₂O生成,这被归因为反应过程中,部分氧化态Ag被还原为金属Ag.添加SO₂或同时添加SO₂和H_{2相似文献}