Utilization of Bagasse Energy in Thailand

Bagasse, a biomass fuel, is the waste generated by the sugar-making process from sugar cane. Sugar making is one of the most important agricultural-produce processing industries for developing countries in Southeast Asia, Latin America and Africa. As sugar producing plants need electric power and process steam, co-generation using bagasse as an alternate fuel for petroleum has been in use for some time. Thailand recently became one of the largest sugar exporters by enlarging plant capacities and improving equipment, thus reducing its production cost. In addition, the Thai government promotes power generation using bagasse as a means to combat global warming by raising the purchase price of the surplus power. The industry is in the process of further raising the plant capacity, and improving the power-generating efficiency. This will enable a plant to generate more electric power than its in-plant need so that the surplus power can be sold to the commercial grid. It also plans to become a local power supplier during off-season of sugar making by adding a condensing turbine generator. A typical Thai sugar plant of the latest design generates steam of 4Mpa at the bagasse boiler outlet with the temperature of 400°C at 84% boiler efficiency. With the bagasse LHV of 7,540 kJ/kg and that of fuel oil 41, 840 kJ/kg, and taking 90%as oil-burning boiler efficiency, 5.95 kg of bagasse would replace 1 kg of oil. The Kyoto Mechanism defines CO₂ generation by fuel oil as 2.65 kg per liter. Using 0.85for the specific gravity of fuel oil, the amount of CO₂ generation will be 3.12 kg-CO₂/kg. Therefore, CO₂reduction per ton of bagasse in terms of fuel oil will be: 3.12/5.95 =0.524 kg-CO₂/kg-bagasse. As 1 kg of bagasse generates 2 kg of steam, the CO₂reduction of a 100t/h steam boiler will be112,660 ton/year for an annual operation of4,300 hours, as follows. 0.524 × 100/2 = 26.2 t-CO₂/h, 26.2 × 4,300 =112,660 t-CO₂/year. This revised version was published online in August 2006 with corrections to the Cover Date.     

Biomass-based negative emission technology options with combined heat and power generation

Biomass-based combined heat and power (CHP) generation with different carbon capture approaches is investigated in this study. Only direct carbon dioxide (CO₂) emissions are considered. The selected processes are (i) a circulating fluidized bed boiler for wood chips connected to an extraction/condensation steam cycle CHP plant without carbon capture; (ii) plant (i), but with post-combustion CO₂ capture; (iii) chemical looping combustion (CLC) of solid biomass connected to the steam cycle CHP plant; (iv) rotary kiln slow pyrolysis of biomass for biochar soil storage and direct combustion of volatiles supplying the steam cycle CHP plant with the CO₂ from volatiles combustion escaping to the atmosphere; (v) case (iv) with additional post-combustion CO₂ capture; and (vi) case (iv) with CLC of volatiles. Reasonable assumptions based on literature data are taken for the performance effects of the CO₂ capture systems and the six process options are compared. CO₂ compression to pipeline pressure is considered. The results show that both bioenergy with carbon capture and storage (BECCS) and biochar qualify as negative emission technologies (NETs) and that there is an energy-based performance advantage of BECCS over biochar because of the unreleased fuel energy in the biochar case. Additional aspects of biomass fuels (ash content and ash melting behavior) and sustainable soil management (nutrient cycles) for biomass production should be quantitatively considered in more detailed future assessments, as there may be certain biomass fuels, and environmental and economic settings where biochar application to soils is indicated rather than the full conversion of the biomass to energy and CO₂.

     

Sustainable global energy supply based on lignocellulosic biomass from afforestation of degraded areas

An important aspect of present global energy scenarios is the assumption that the amount of biomass that can be grown on the available area is so limited that a scenario based on biomass as the major source of energy should be unrealistic. We have been investigating the question whether a Biomass Scenario may be realistic. We found that the global energy demand projected by the International Energy Agency in the Reference Scenario for the year 2030 could be provided sustainably and economically primarily from lignocellulosic biomass grown on areas which have been degraded by human activities in historical times. Moreover, other renewable energies will contribute to the energy mix. There would be no competition with increasing food demand for existing arable land. Afforestation of degraded areas and investment for energy and fuel usage of the biomass are not more expensive than investment in energy infrastructure necessary up to 2030 assumed in the fossil energy based Reference Scenario, probably much cheaper considering the additional advantages such as stopping the increase of and even slowly reducing the CO₂ content of the atmosphere, soil, and water conservation and desertification control. Most importantly, investment for a Biomass Scenario would be actually sustainable, in contrast to investment in energy-supply infrastructure of the Reference Scenario. Methods of afforestation of degraded areas, cultivation, and energetic usage of lignocellulosic biomass are available but have to be further improved. Afforestation can be started immediately, has an impact in some few years, and may be realized in some decades. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.

Feasibility of husk-fuelled steam engines as prime mover of grid-connected generators under the Thai very small renewable energy power producer (VSPP) program

Rice husk generated as a by-product of rice mill processes can be utilized as an energy source for husk-fuelled rice mills. The economic evaluation of the investment of husk-fuelled steam engine rice mills, which generate mechanical energy for the direct driving of milling equipments, has previously been presented in literature. It was reported that for some particular conditions of rice mill, the investment of husk-fuelled steam engine as energy-saving technology is financially feasible. Since May 2002, electricity distributors in Thailand have allowed renewable energy producers up to 1 MW to connect their generators to the grid in order to sell surplus electricity to the grid. This arrangement creates more income opportunities for husk-fuelled steam engine owners to generate not only mechanical power for rice milling processes, but also surplus electricity for feeding onto the grid. The objective of this study is to investigate the financial feasibility of the investment in a husk-fuelled steam engine system which drives grid-connected electrical generators, reduces rice mill demand and electricity and sells surplus electricity to the grid. The technical and economic data for rice mill sizes 35, 45, 60, 95 and 120 t/d presented in this study show that the husk-fuelled steam engine system with grid-connected generators improves the economic performance of applying the system solely for the largest 120 t/d rice mills. However, the conventional husk-fuelled steam engine without electric generator gives a better economic performance of the rice mills sizes from 45 to 95 t/d.     

A 50 MW concentrating solar power plant for Jordan

The potential of concentrating solar power plant (CSPP) technology in Jordan is assessed and the next steps for development of the first CSPP in the country are presented. For this purpose, a prototype of a 50 MW CSPP for electricity generation in Jordan is proposed and analysis of its economic feasibility has been performed. Moreover, a calculation model – using the concept design of the proposed CSPP, and the solar irradiation data – was developed to estimate the energy yield of the plant. Based on the analyzed solar irradiation data, it was found that Jordan has an outstanding potential for CSPP, especially in the southern locations of the country such as Quweira. At the same time Jordan's energy master plan is seeking for independent energy supply and for an increasing share of renewable energies. Furthermore, Jordan's demand curve over a day closely matches the electricity production of the proposed plant. Combination of these factors creates a very favorable situation. Therefore, establishment of the proposed 50 MW CSPP is highly recommended not only in Jordan, but also in many other countries, which have similar political and economical conditions such as those countries located in the Middle East and North Africa (MENA) region.     

Economic potential of biomass gasification projects under clean development mechanism in India

The Clean Development Mechanism (CDM) of the Kyoto Protocol provides Annex-I (industrialized) countries with an incentive to invest in emission reduction projects in non-Annex-I (developing) countries to achieve a reduction in CO₂ emissions at lowest cost that also promotes sustainable development in the host country. Biomass gasification projects could be of interest under the CDM because they directly displace greenhouse gas emissions while contributing to sustainable rural development. However, there is only one biomass gasifier project registered under the CDM so far. In this study, an attempt has been made to assess the economic potential of biomass gasifier-based projects under CDM in India. The preliminary estimates based on this study indicate that there is a vast theoretical potential of CO₂ mitigation by the use of biomass gasification projects in India.The results indicate that in India around 74 million tonne agricultural residues as a biomass feedstock can be used for energy applications on an annual basis. In terms of the plant capacity the potential of biomass gasification projects could reach 31 GW that can generate more than 67 TWh electricity annually. The annual CER potential of biomass gasification projects in India could theoretically reach 58 million tonnes. Under more realistic assumptions about diffusion of biomass gasification projects based on past experiences with the government-run programmes, annual CER volumes by 2012 could reach 0.4–1.0 million and 1.0–3.0 million by 2020. The projections based on the past diffusion trend indicate that in India, even with highly favorable assumptions, the dissemination of biomass gasification projects is not likely to reach its maximum estimated potential in another 50 years. CDM could help to achieve the maximum utilization potential more rapidly as compared to the current diffusion trend if supportive policies are introduced.     

Methane Emissions from Large Dams as Renewable Energy Resources: A Developing Nation Perspective

By means of a theoretical model, bootstrap resampling and data provided by the International Commission On Large Dams (ICOLD (2003) World register of dams. http://www.icold-cigb.org) we found that global large dams might annually release about 104 ± 7.2 Tg CH₄ to the atmosphere through reservoir surfaces, turbines and spillways. Engineering technologies can be implemented to avoid these emissions, and to recover the non-emitted CH₄ for power generation. The immediate benefit of recovering non-emitted CH₄ from large dams for renewable energy production is the mitigation of anthropogenic impacts like the construction of new large dams, the actual CH₄ emissions from large dams, and the use of unsustainable fossil fuels and natural gas reserves. Under the Clean Development Mechanism of the Kyoto Protocol, such technologies can be recognized as promising alternatives for human adaptations to climate change concerning sustainable power generation, particularly in developing nations owning a considerable number of large dams. In view of novel technologies to extract CH₄ from large dams, we estimate that roughly 23 ± 2.6, 2.6 ± 0.2 and 32 ± 5.1 Tg CH₄ could be used as an environmentally sound option for power generation in Brazil, China and India, respectively. For the whole world this number may increase to around 100 ± 6.9 Tg CH₄.     

Simulation of a 100-MW solar-powered thermo-chemical air separation system combined with an oxy-fuel power plant for bio-energy with carbon capture and storage (BECCS)

The combination of concentrated solar power–chemical looping air separation (CSP-CLAS) with an oxy-fuel combustion process for carbon dioxide (CO₂) capture is a novel system to generate electricity from solar power and biomass while being able to store solar power efficiently. In this study, the computer program Advanced System for Process Engineering Plus (ASPEN Plus) was used to develop models to assess the process performance of such a process with manganese (Mn)-based oxygen carriers on alumina (Al₂O₃) support for a location in the region of Seville in Spain, using real solar beam irradiance and electricity demand data. It was shown that the utilisation of olive tree prunings (Olea europaea) as the fuel—an agricultural residue produced locally—results in negative CO₂ emissions (a net removal of CO₂ from the atmosphere). Furthermore, it was found that the process with an annual average electricity output of 18 MW would utilise 2.43% of Andalusia’s olive tree prunings, thereby capturing 260.5 k-tonnes of CO₂, annually. Drawbacks of the system are its relatively high complexity, a significant energy penalty in the CLAS process associated with the steam requirements for the loop-seal fluidisation, and the gas storage requirements. Nevertheless, the utilisation of agricultural residues is highly promising, and given the large quantities produced globally (~?4 billion tonnes/year), it is suggested that other novel processes tailored to these fuels should be investigated, under consideration of a future price on CO₂ emissions, integration potential with a likely electricity grid system, and based on the local conditions and real data.

     

Experimental investigation of open core downdraft biomass gasifier for food processing industry

This paper deals with field related experience of a low temperature industrial heat application through biomass gasification. The gasification system is essentially consists of an open top down draft reactor lined with ceramic. The experiment reveals that 6.5 kg of liquefy petroleum gas (LPG) is fully replaced by 38 kg of sized wood on hourly basis. The maximum temperature attained was 367°C in 130 min at 100.7 Nm³ h⁻¹ gas flow rate. This system has resulted a saving of about 19.5 tons of LPG over 3,000 h of operation, implying a saving of about 33 tons of CO₂ emission, thus a promising candidate for clean development mechanism. Fuel economic analysis of gasifier system showed that the saving was about 13,850 US$ for 3,000 h of baking operation.     

Carbon storage versus fossil fuel substitution: a climate change mitigation option for two different land use categories based on short and long rotation forestry in India

Short rotation bioenergy crops for energy production are considered an effective means to mitigate the greenhouse effect, mainly due to their ability to substitute fossil fuels. Alternatively, carbon can be sequestered and stored in the living biomass. This paper compares the two land use categories (forest land and non-forest land) for two management practices (short rotation vs. long rotation) to study mitigation potential of afforestation and fossil fuel substitution as compared to carbon storage. Significant carbon benefit can be obtained in the long run from using lands for growing short rotation energy crops and substituting fossil fuels by the biomass thus produced, as opposed to sequestering carbon in the biomass of the trees. When growth rates are high and harvest is used in a sustainable manner (i.e., replanting after every harvest), the opportunities for net carbon reductions appear to be fossil fuel substitution, rather than storage in ecosystem biomass. Our results suggest that at year 100 a total of 216 Mg C ha⁻¹ is sequestered for afforestation/reforestation using long rotation sal (Shorea robusta Gaertn.f) species, as opposed to offset of 412 Mg C ha⁻¹ for carbon storage and fossil fuel substitution for short rotation poplar (Populus Deltoides Marsh) plantations. The bioenergy option results in a continuous stream of about 3 Mg C ha⁻¹ yr⁻¹ of carbon benefits per year on forest land and 4 Mg C ha⁻¹ yr⁻¹ on non-forest land. Earlier studies have shown that in India waste land availability for establishing energy plantations is in the range of 9.6 to 36.5 Mha. Thus, using the 758 Tg biomass per year generated from 9.6 Mha waste land gives a mitigation potential in the range of 227 to 303 Tg C per year for carbon storage and fossil fuel substitution from poplar plantation for substituting coal based power generation. Depending upon the land availability for plantation, the potential for energy generation is in the range of 11,370 PJ, possibly amounting to a bioenergy supply of 43% of the total projected energy consumption in 2015. Further studies are needed to estimate the mitigation potential of other species with different productivities for overall estimation of the economic feasibility and social acceptability in a tropical country like India.     

生物质能源及发电技术研究

随着能源消耗和环境污染之间矛盾的加剧,使得人类需要寻找一些相对比较清洁的可再生能源。生物质能源由于其数量巨大,环境污染小,并具有可再生性,成为目前比较好的选择之一。生物质能发电是生物质能利用的主要方式之一。介绍了生物质能的特点及利用转化方式,重点讲述了直接燃烧发电技术、气化发电技术以及生物质燃料电池技术,最后根据我国国情指出了生物质能利用的主要问题及几点建议。对我国生物质能发电的发展提供了技术参考和技术支持。     

生物质发电项目碳排放计算方法应用研究

生物质发电是将废弃生物质变成可再生能源得以充分利用,这些工程将减少来自于生物质自然腐烂和无控燃烧产生的温室效应,这不仅节约了煤炭,同时也减少了二氧化碳的排放。本文中以某生物质项目发电为例,根据CDM方法学ACM0006计算了该项目的减排量。结果表明,该项目10年间共减少了二氧化碳排放量2 075 140吨,给中国带来了可观的经济效益和环境效益。     

A Greenhouse Gas Balance of two Existing International Biomass Import Chains

Various utility companies are considering or already initiated the import of biomass from abroad for electricity generation, especially via co-firing in coal-fired power plants. This results in international logistic biomass supply chains, which raise questions on the environmental performance of such chains. In this study, a life cycle inventory has been performed on two existing biomass import chains to evaluate the greenhouse gas balance of biomass import for co-firing. We considered production, transport and co-firing of wood pellets from Canada and palm kernel shells from Malaysia in a 600 MW _e coal-fired power plant in the Netherlands. Those chains are compared with various reference systems for energy production and the alternative use of biomass. Primary energy savings of these import and co-firing chains are between 70% and 100% of the biomass energy content. Net avoided greenhouse gas emissions are in the range of 340–2100 g/kWh. In the most optimistic scenario, pellet co-firing avoids methane emissions that would have occurred if the pellets were decomposed at landfills when not applied for energy production. In the most pessimistic scenario, palm kernel shell co-firing competes with the application as resource for animal feed production, which requires production and transport of an alternative resource. As the energy reference systems of the importing and exporting country and the alternative application of biomass have a significant impact on the net avoided greenhouse gas emissions, these factors should be considered explicitly when studying biomass trade for energy purposes.     

Fertilization trajectory of the root crop Raphanus sativus across atmospheric pCO2 estimates of the next 300 years

Plant biomass is known to increase in response to elevated atmospheric CO₂ concentration (pCO₂); however, no experiments have quantified the trajectory of crop fertilization across the full range of pCO₂ levels estimated for the next 300 years. Here we quantify the above- and below-ground biomass response of Raphanus sativus (common radish) across eight pCO₂ levels ranging from 348 to 1791 ppmv. We observed a large net biomass increase of 58% above ground and 279% below ground. A large part of the net increase (38% of the above-ground and 53% of the below-ground) represented biomass fertilization at the high levels of pCO₂ (700–1791 ppmv) predicted if fossil fuel emissions continue unabated. The trajectory of below-ground fertilization in R. sativus greatly exceeded a trajectory based on extrapolation of previous experiments for plants grown at pCO₂ < 800 ppmv. Based on the experimental parameters used to grow these plants, we hypothesize that these experiments represent the maximum CO₂ fertilization that can be achieved for this plant growing under low light levels. If the below-ground biomass enhancement that we have quantified for R. sativus represents a generalized root-crop response that can be extrapolated to agricultural systems, below-ground fertilization under very high pCO₂ levels could dramatically augment crop production in some of the poorest nations of the world, provided that water resources are sufficient and sustainable.     

生物质发电项目碳排放计算方法应用研究

生物质发电是将废弃生物质变成可再生能源得以充分利用,这些工程将减少来自于生物质自然腐烂和无控燃烧产生的温室效应,这不仅节约了煤炭的同时也减少了二氧化碳的排放。本文中以某生物质项目发电为例,根据CDM方法学ACM0006计算了该项目的减排量。结果表明,该项目10年间共减少了二氧化碳排放量2,075,140 t,给我国带来了可观的经济效益和环境效益。     

江苏省高速公路站区光伏能源综合利用研究

基于江苏省高速公路沿线服务区、收费站、办公楼屋面面积以及服务区停车场面积统计数据,估算了可利用屋面面积和进行光伏车棚改造的服务区停车场面积。测算了光伏屋面、光伏车棚的装机规模和发电量,结合高速公路用电情况分析了运行方式。经测算:江苏省高速公路服务区和收费站屋面可安装光伏发电总装机容量为32 MW,首年发电量为3200万kWh,全省高速公路光伏屋面25年发电总量约7.3亿kWh;江苏省高速公路光伏车棚可安装光伏发电装机容量约11 MW,25年发电总量约2.5亿kWh;高速公路站区光伏系统所发电量均小于其昼间用电量,站区光伏发电能够以“自发自用”的模式运行。     

Energy sector reform in Eritrea: initiatives and implications

The Government of Eritrea gave priority status to the energy sector immediately after the country's independence in May 1991, as manifested by the rapid improvement in electricity and oil supplies. Electricity generation capacity has increased from a total of 30 MW in 1991 to over 130 MW at present. The lengths of transmission and distribution lines have similarly increased from 150 km to 400 km and from 800 to 1300 km respectively. However, as in most Sub-Saharan Africa, this public utility is characterised by inefficient managerial, technical and financial performances, an inability to mobilize the funds needed for expansion, low repair and maintenance capacity, inappropriate tariff rates, and inadequate revenue collection mechanisms. This has led the government to take appropriate reform measures in recent years, including the restructuring of the Eritrea Electric Corporation (EEC) to operate on commercial principles, setting tariffs based on real costs and reasonable profits, effective collection of revenues, the minimization of wastage and loss in the delivery of energy services, facilitating the private sector participation, and ring-fencing the interests of the poor by setting up a Rural Electrification Fund. A Regulatory body has been established to enforce these reform measures. Recognising the role of modern energy in poverty reduction and achieving the Millennium Development Goals (MDGs), the Government with the support of its development partners is expanding energy services to rural areas in an innovative manner. The Government's commitment to diversify energy sources is exemplified by its agreement with the Global Environment Facility (GEF) to share the costs of an on-going pilot wind energy project. It has also established an Energy Research and Training Centre to promote the application of renewable energies and improved biomass stoves throughout Eritrea.     

Greenhouse gas balances of molasses based ethanol in Nepal

This paper evaluates life cycle greenhouse gas (GHG) balances in production and use of molasses-based ethanol (EtOH) in Nepal. The total life cycle emissions of EtOH is estimated at 432.5 kgCO_2eq m⁻³ ethanol (i.e. 20.4 gCO_2eq MJ⁻¹). Avoided emissions are 76.6% when conventional gasoline is replaced by molasses derived ethanol. A sensitivity analysis was performed to verify the impact of variations in material and energy flows, and allocation ratios in the GHG balances. Market prices of sugar and molasses, amount of nitrogen-fertilizers used in sugarcane production, and sugarcane yield per hectare turn out to be important parameters for the GHG balances estimation. Sales of the surplus electricity derived from bagasse could reduce emissions by replacing electricity produced in diesel power plants. Scenario analysis on two wastewater processes for treatment of effluents obtained from ethanol conversion has also been carried out. If wastewater generated from ethanol conversion unit is treated in pond stabilization (PS) treatment process, GHG emissions alarmingly increase to a level of 4032 kgCO_2eq m⁻³ ethanol. Results also show that the anaerobic digestion process (ADP) and biogas recovery without leakages can significantly avoid GHG emissions, and improve the overall emissions balance of EtOH in Nepal. At a 10% biogas leakage, life cycle emissions is 1038 kgCO_2eq m⁻³ ethanol which corresponds to 44% avoided emissions compared to gasoline. On the other hand, total emissions surpass the level of its counterpart (i.e. gasoline) when the leakage of biogas exceeds 23.4%.     

Development of alternative energy sources for GHG emissions reduction in the textile industry by energy recovery from cotton ginning waste

The agricultural sector and primarily its cotton subsector are of great importance for Greece, due to the intensive agricultural activities. The wastes from cotton ginning plants are also considerable and can be valorized for bioenergy production. The substitution of conventional by green fuels, which can be produced from cotton ginning wastes, is a step towards: (a) economic and environmental sustainability for the textile industry and (b) the development of alternative energy supplies, contributing to the reduction of GHG emissions. Furthermore, it consists an especially attractive opportunity to invest in rural areas. The present paper concerns the feasibility study for energy recovery from cotton ginning waste with GHG emissions reduction in a textile plant located in Northern Greece. The aim was to replace part of heavy fuel oil used for the thermal needs of the plant by biomass. The results showed that the most economically interesting energy option for a bioenergy unit in the above textile plant is 5 MW for the coverage of the 52% of the plant's thermal requirements.     

两种模式下中国未来发电行业发展情景及其环境效益分析

为了研究“双碳”目标模式下我国发电行业发展前景及带来的环境效益,建立了饱和“S”状灰色模型计算了按照旧有发电模式——非“双碳”模式下2021～2060年发电行业装机容量和发电量,并基于“中国2030年能源电力发展规划研究及2060年展望报告”计算获得了“双碳”模式下2021～2060年发电行业装机容量和发电量,对比研究了两种模式下中国未来发电行业的发展情景.通过物料衡算法和火电行业排放绩效构建了CO₂、 SO₂、 NO_x、 PM、 PM₁₀和PM_2.5的排放因子以及减排因子,定义了用于衡量污染物减排量的4种环境效益A₁～A₄.结果表明,在“双碳”模式下,火电机组将于2026年实现碳达峰,之后年均降低0.28亿kW,同时要求可再生能源发电机组于2020年后年均增加1.54亿kW以实现碳中和.与非“双碳”模式相比,“双碳”模式下火力发电装机容量将大幅度减少,可再生能源发电装机容量将大量增加,由此产生巨大的环境效益A₁...