Enzymatic natural dyeing of cotton and silk fabrics without metal mordants

Two step ultrasonic dyeing of cotton and silk fabrics with natural dyes, Terminalia arjuna, Punica granatum, and Rheum emodi have been developed in which an enzyme is complexed with tannic acid first as a pretreatment. This was found to be comparable with one step simultaneous dyeing. The effectiveness of three enzymes—protease-amylase, diasterase and lipase was determined. The enzymatic treatment gave cotton and silk fabrics rapid dye adsorption kinetics and total higher adsorption than untreated samples for all the three dyes. The CIELab values also showed improvement by enzymatic treatment. The tannic acid-enzyme-dye combination method offers an environmentally benign alternative, ‘soft chemistry’ to the metal mordanted natural dyeing.     

PI纤维在空间带电粒子辐照下的力学性能损伤

目的研究聚酰亚胺(PI)纤维在电子辐照、质子辐照、应力耦合质子辐照条件下力学性能的损伤行为。方法采用中国科学院长春应用化学研究所自主合成并纺丝制备的聚酰亚胺纤维,在空间环境模拟设备辐照的条件下,研究空间带电粒子对聚酰亚胺纤维辐照后的力学损伤行为,并通过XQ-1型纤维强度仪对辐照前后的样品进行拉伸试验。结果在低能电子辐照条件下,聚酰亚胺纤维的拉伸强度、模量和断裂伸长率均有所降低,但变化不太显著;高能电子辐照会提高材料的模量;质子辐照后,材料的拉伸强度和断裂伸长率随着辐照注量的增加明显降低;单一施加5%的应变会使聚酰亚胺纤维的拉伸力学性能有一定量下降。与单一应变样品相比,应力耦合质子辐照样品的拉伸强度和断裂伸长率进一步下降,但是与单一质子辐照样品相比,应力耦合辐照样品的拉伸强度和断裂伸长率都更高。结论无论是在低能电子辐照条件下,还是在高能电子辐照条件下,电子辐照对聚酰亚胺纤维力学性能影响均较微弱,而质子辐照会较大程度地降低材料的力学性能,增加应力耦合效应之后,质子辐照对材料的力学性能影响减弱。     

A new process of combined pretreatment and dyeing: REST

Use of enzymes in textile processes has many advantages as far as the environmentally friendly processes are concerned. These advantages include water and energy savings, less chemical use, less fabric damage, mild and environmentally friendly process conditions. In this work, C.I. Reactive Yellow 15, C.I. Reactive Red 21 and C.I. Reactive Blue 19 were used to dye untreated woven cotton fabric in a laboratory scale dyeing machine, on a pilot scale jig and on a pilot scale winch by using a single bath combined process, in which various enzymes, namely, amylase, pectinase, and catalase were employed. This new process was named as the “Rapid Enzymatic Single-bath Treatment” (REST), since it was completed almost in half of the conventional dyeing time, and all of the stages, namely, desizing, scouring, bleaching and dyeing were carried out in a single bath without replacing the process water with fresh water until the end of the dyeing. In the REST process, the untreated, starch-sized fabric was first desized by amylase enzyme, and this was followed by a pectinase treatment in the same bath. The fabric was then bleached by H₂O₂ in the same bath, and after the hydrogen peroxide bleaching; the catalase enzyme was added to the bath to remove H₂O₂ residues before reactive dyeing. Without carrying out intermediate washings/rinsings between these processes, the reactive dyeing was carried out in a conventional way in the same bath, and finally, the fabric was taken from the bath and washed out. The colour yield was compared with the dyeings which were carried out conventionally in separate baths. Finally, the REST has many benefits in terms of water saving, reduced process time and energy consumptions compared to the conventional preparatory and dyeing process of cotton fabrics.     

Life cycle assessment of mobile phone housing

The life cycle assessment of the mobile phone housing in Motorola(China) Electronics Ltd. was carried out, in which materials flows and environmental emissions based on a basic production scheme were analyzed and assessed. In the manufacturing stage, such primary processes as polycarbonate molding and surface painting are included, whereas different surface finishing technologies like normal painting, electroplate, IMD and VDM etc. were assessed. The results showed that housing decoration plays a significant role within the housing life cycle. The most significant environmental impact from housing production is the photochemical ozone formation potential.Environmental impacts of different decoration techniques varied widely, for example, the electroplating technique is more environmentally frieodly than VDM. VDM consumes much more energy and raw material. In addition, the results of two alternative scenarios of dematerialization showed that material flow analysis and assessment is very important and valuable in selecting an environmentally friendly process.     

废弃红砖微粉填料制备环保乳胶漆及其性能研究

研究了利用废弃红砖生产环保乳胶漆的制备方法,通过正交试验分析了乳液种类、乳液含量、醇酯十二含量、丙二醇含量和增稠剂含量对环保乳胶漆性能的影响.结果表明,废弃红砖微粉与苯丙乳液有较好的相容性,当乳液含量为25%~30%,醇酯十二0.4%~1.2%,丙二醇3.00%~3.75%,增稠剂1‰~1.5‰时,砖质环保乳胶漆产品低温稳定性良好,可成完全悬浮状态,表干时间小于30min,摆杆阻尼次数可达103次,附着力等级大于5,这为建筑废物资源化提供新的途径.     

仿生SiC陶瓷材料的制备和性能

仿生SiC陶瓷材料是一种新兴的环境友好材料,因其具有密度低、强度高、耐腐蚀、耐磨损、抗氧化和生物相容性好等优点,在机械、化工、催化、生物医学等领域都有着广阔的应用前景。就仿生SiC陶瓷材料的多种制备工艺和其机械性能、热性能、电性能、生物相容性等进行了综述,并对其存在的问题进行了分析,对其发展趋势进行了展望。     

地沟油脱胶工艺条件优化

研究地沟油的脱胶工艺,比较了磷酸脱胶、水脱胶和磷酸-水联合脱胶3种方法的脱胶效果,考察了脱胶温度、磷酸用量、酸化时间、水用量和水化时间对磷酸-水联合脱胶效果的影响,并通过正交试验对其脱胶条件进行了优化。结果表明,磷酸脱胶、水脱胶和磷酸-水联合脱胶的脱胶率分别为8.78%、68.18%和79.32%;磷酸-水联合脱胶的最优脱胶条件为:脱胶温度60℃,磷酸用量0.1%,酸化时间40 min,水用量3%,水化时间30 min,在此条件下,脱胶率为96.70%。因此,磷酸-水联合脱胶可除去地沟油中的胶体,达到生物柴油原料的要求。     

稳定型纳米零价铁去除地下水中2,4-二氯苯酚

为改善纳米零价铁(NZVI)在水溶液中容易发生团聚和易被氧化的缺点.本文研究利用廉价易得的环境友好型材料羧甲基淀粉钠(CMS)对NZVI进行包覆改性,利用空间位阻效应提高其分散悬浮性.利用透射电镜和X射线衍射研究了改性后的纳米铁微观结构及物相组成,通过化学实验研究其对2,4-二氯苯酚(2,4-DCP)的去除效果.结果表明,改性后的NZVI直径大约在80~100 nm,呈链状或分散颗粒分布,主要物质组成为零价铁,具有强还原性.当CMS的比例为80.00%时,悬浮性最佳;经过CMS包覆改性后,NZVI还保留原有的活性,在不同包覆比例对于2,4-DCP的去除效果的实验中发现,同样CMS比例为80%时去除效果最好,达到83.69%,且有明显的脱氯降解过程.     

Evaluation of environmentally friendly lubricant for aluminum cold forging using friction test based on spline extrusion

It is required to replace the aluminum fluoride coating, which is a popular lubricant for aluminum alloy cold forging in Japan, with environmentally friendly lubricants, because the aluminum fluoride coating has high environmental risks and needs much expense. Evaluations of lubrication performance are necessary before lubricant replacement. The authors proposed new friction test based on combined forward spline-backward can extrusion. It can realize large surface expansion, which is a characteristic of aluminum cold forging. In the present paper, a double-layer-type environmentally friendly solid lubricant film and the aluminum fluoride coating were applied to a precipitation hardened aluminum alloy. The lubrication performance was evaluated by the friction test. The double-layer-type lubricant showed superior performance enough for the replacement. The effect of surface treatment applied to workpiece on the lubrication performance was also investigated. The surface asperity generated by a wet-blasting showed high pickup resistance and low friction.     

壳聚糖包覆微胶囊红磷的制备及性能表征

目的 降低红磷(RP)烟火剂的吸湿率及感度,以此提高其使用过程中的安全性能.方法 以生物基材料壳聚糖(CS)为囊壳结构,采用高效简便的工艺,制备壳聚糖包覆微胶囊红磷(CSRP),对CSRP进行红外光谱测试(FTIR)、X射线电子能谱分析(XPS)、扫描电子显微镜(SEM)测试及热重(TG)测试,并对RP及CSRP进行吸...     

卤氧化铋光催化剂改性的研究进展及应用

随着全球环境问题与能源问题的不断加剧,人们迫切需要开发一些高效、环保、稳定的光催化剂。卤氧化铋(BiOX,X=Cl、Br、I)因其独特的层状结构,优异的光学、电学性能,在光催化领域受到了越来越多的关注。虽然BiOX光催化剂在光催化反应中展现出了优异性能,但其光催化效率仍有待提高。简要叙述了BiOX的结构与性能以及当前主流的制备方法,主要概述了最近几年卤氧化铋光催化剂改性的研究进展。改性方法主要有微结构调控、晶面与缺陷调控、掺杂、构造异质结等,这些方法主要是通过提高卤氧化铋或卤氧化铋复合物的光吸收能力、光生载流子的分离和运输效率、以及活性位点的暴露量来实现改性。介绍了其在环境、能源和生物等领域的应用,同时对BiOX的发展提出了问题和展望。     

碳纳米管的制备方法及在环保领域中的应用

介绍了碳纳米管的结构和特性,综述了其主要的制备方法,介绍了碳纳米管在环境治理、环境分析和环境保护等领域的应用,这些应用主要基于碳纳米管本身优异的吸附性能和电化学机械性能,最后探讨了目前碳纳米管在制备和环境应用中所存在的问题.     

壳聚糖和FeS改性生物炭吸附四环素:吸附机制与位能分布

实验以市政污泥为生物质炭原料,并以硫化亚铁和壳聚糖对其改性,制得一种新型环保的吸附材料（SB-FeS）.以四环素（TC）为目标污染物,通过批次实验、大量表征分析、数学模型分析对SB-FeS吸附TC的机制进行了详述.实验结果表明,SB-FeS对TC的最大吸附量为183.01 mg·g^-1;SB-FeS对TC的吸附为物理吸附和化学吸附共同作用.SB-FeS对TC的吸附机制主要为静电吸引、孔隙填充、螯合、离子交换、硅酸盐键结合和氢键结合.此外,位点能量分布的研究表明,TC会优先占据高能吸附位点,随后逐渐占据低能位点;且溶液温度升高,SB-FeS表面会愈发不均匀.实验证明SB-FeS对TC吸附是有效的,并且对于吸附机理的探讨可以为后续研究提供帮助.     

超市塑料袋使用行为的环境实验研究

塑料购物袋一直是社会关注的热点环境问题。文章以上海某超市为对象,采用现场观察实验方法记录了5 086份超市顾客塑料袋使用行为的样本,初步揭示了超市塑料袋使用情况和塑料袋使用的顾客行为特征,尝试为超市塑料袋的环境管理政策提供基础性的科学依据。结果表明:(1)超市中主要有3种塑料袋使用方式,依次为购买塑料袋、自带购物袋、使用免费手撕袋,其比例为15%、29%、9%,说明目前塑料袋使用行为具有一定的多样性;(2)影响顾客购买塑料袋的因素为是否有会员卡、是否徒手购物、购物金额,其偏相关系数依次为0.114、0.085、0.042。占总样本63.4%的单人购物情境中,购买塑料袋的影响因素为是否徒手购物、是否有会员卡、年龄、购物金额、性别,偏相关系数依次为0.849、0.486、0.329、0.291、0.180;说明影响塑料袋使用的因素具有综合性和复杂性。(3)顾客购物金额、购物件数、结账时间与塑料袋购买比例有密切的正相关关系;(4)按照购买塑料袋的倾向程度,可将顾客分为高、中、低3类特征群体。其中,购买倾向最高的顾客特征为无会员卡的男性中青年、非徒手购物,购物金额较高。文章研究为解决环境管理问题提供了一种基于现场观察实验方法的案例参考,建议将定量、可重复、可检验、以现场观察记录主的实验方法应用于各类环境问题研究和解决方案中,为环境管理提供更扎实的科学依据。     

Low-temperature plasma induced phosphate groups onto coffee residue-derived porous carbon for efficient U(VI) extraction

For the continuous utilization of nuclear energy and efficient control of radioactive pollution, low-cost materials with high efficient U(VI) removal are of great importance. In this study, low temperature plasma method was applied for the successful modification of O-phosphorylethanolamine (O-PEA) on the porous carbon materials. The produced materials (Cafe/O-PEA) could adsorb U(VI) efficiently with the maximum sorption capacity of 648.54 mg/g at 1 hr, T=298 K, and pH=6.0, much higher than those of most carbon-based composites. U(VI) sorption was mainly controlled by strong surface complexation. From FTIR, SEM-EDS and XPS analyses, the sorption of U(VI) was related to the complexation with -NH₂, phosphate and -OH groups on Cafe/O-PEA. The low temperature plasma method was an efficient, environmentally friendly and low-cost method for surface modification of materials for the effective enrichment of U(VI) from aqueous solutions.     

电化学微传感器检测水中痕量铜离子

为改善微电极在阳极溶出伏安法检测重金属离子过程中低电流响应和低电催化能力的缺点,提出了一种在碳纤维微电极表面合成还原氧化石墨烯/纳米金材料制得还原氧化石墨烯纳米金修饰碳纤维微电极（rGO/AuNPs CFMEs）的方法.通过SEM表征,所制备的rGO/AuNPs CFMEs具有比表面积高、吸附能力强和催化活性好的特点,因此改性微电极适合作为方波阳极溶出伏安法（SWASV）测定水中铜离子（Cu²⁺）的工作电极.在构建微传感器测试水中痕量铜离子系统后,对pH值、电导率、富集时间和富集电位等检测条件进行了优化.在pH值为4,电导率为36.1S/m,富集时间为360s,富集电位为-1.2V的最佳条件下,铜的线性范围和检出限分别0~1.0μmol/L和2.4nmol/L.此外,微传感器的可重复性、长期稳定性以及选择性也得到了验证.     

Application of an alkaline protease in leather processing: an ecofriendly approach

Proteolytic enzyme isolated from Aspergillus tamarii prepared by solid state fermentation was studied for dehairing of goat skins in the tannery. The stability of the enzyme for dehairing was optimized at different environmental parameters. Unhairing of goat skins could be obtained at pH 9–11 and temperatures 30–37°C with enzyme concentration of 1% w/v and incubation periods of 18–24 h. The physical properties of the experimental leathers in comparison with the control sets gave better results with respect to tensile strength and elongation at break.     

聚二乙烯基苯功能化纺织布用于快速油水分离的研究

面对日趋严重的海洋漏油事故及工业含油废水排放问题,本研究提出了一种基于聚二乙烯基苯（PDVB）的超疏水纺织布制备方法,将二乙烯基苯单体在纺织布纤维上聚合生长,形成超疏水涂层,用于快速油水分离.结果表明,制备的纺织布具有优异的超疏水性,水接触角为155°,对不同油/水混合物的分离效率均高于97%,渗透通量达3077 L·m^-2·h^-1.在砂纸磨损40次、超声处理60 min和不同溶剂浸泡实验中依旧维持超疏水性.研究表明,该超疏水纺织布的制备方法高效、简单、环保、成本低,适合大规模生产,所制备的超疏水超亲油的纺织布是用于溢油清理和工业含油废水处理的非常有前途的材料.     

超声强化下多相催化臭氧体系处理印染尾水

随着我国对水环境质量要求逐步提高,对于纺织印染废水处理提出了更为严格的排放要求.臭氧(O₃)工艺已常用于纺织印染废水深度处理,但存在臭氧利用率低、氧化不彻底等问题.该研究通过自制陶粒催化剂,构建多相催化臭氧氧化体系,以期改善接触条件,提高处理效率,同时在此基础上引入超声波进一步强化体系处理效率.采用扫描电子显微镜(SEM)、X射线衍射(XRD)表征了陶粒催化剂,考察了催化剂投加量、超声波频率对印染尾水的COD_Cr去除率,并通过三维荧光光谱、GC/MS等分析了反应前后尾水中有机物的变化特征.结果表明:①自制陶粒催化剂表面较为粗糙,晶面尺寸在36~50 nm之间,投入后可提高臭氧(O₃)体系对印染尾水的COD_Cr去除率(提高了10%~15%),具有较好的催化效率.②引入超声波可进一步提升体系的氧化效率,当超声频率为200 kHz时,出水ρ(COD_Cr)可达到GB 3838—2002《地表水环境质量标准》Ⅴ类要求.③自制陶粒催化剂与超声波的引入主要促进了芳香性蛋白和溶解性微生物代谢产物的氧化分解,且有效地破坏了长链烷烃、环状烷烃、复杂苯系物等有机物,从而实现印染尾水中ρ(COD_Cr)的进一步降解.研究显示,自制陶粒催化剂协同超声波可提高O₃体系对印染尾水的矿化效率且绿色环保,可为我国水环境敏感区域内纺织印染企业或园区废水深度处理工艺的选择提供参考依据.      

廊坊市环保产业发展现状与市场需求分析

针对目前廊坊市环保产业发展现状及存在的问题,以及今后一段时间内环保产品市场的需求进行了分析,并提出了一些建议。