水体新型污染物现场快速富集方法的研究

该文采用新型胶束-乳液聚合法制备了两亲多孔吸附材料作为固相萃取吸附剂,并且为其配套研制了一种可用于现场大体积富集水质中痕量污染物的全自动固相萃取采样装置(LVED)。使用新研制的装置建立了LVED-HPLC-MS/MS方法快速测定环境水样中40种痕量新型污染物的方法,实验优化了大体积固相萃取条件并进行方法学验证,证明该方法具有良好的线性关系(r~2≥0.992),以及较低的检出限(0.002～0.10 ng/L)。将此方法用于实际环境水样中新型污染物的现场富集与检测,不同污染物的加标回收率分别为78.0%～107%,部分污染物实际检测浓度在0.05～90.5 ng/L。该方法是一种简便、快速、高效的现场大体积萃取环境水样中痕量新型污染物的新方法,具有应用和推广前景。     

醇类助溶剂去除砂土中多氯联苯作用机制

醇类助溶剂单一使用及复配表面活性剂使用去除砂土中多氯联苯(PCBs)的关键是增溶和降低界面张力.通过降低界面张力实验和振荡增溶实验分析了醇类助溶剂单一使用对多氯联苯界面张力的降低作用和增溶作用,以及醇类复配Triton X-100使用时醇对Triton X-100降低界面张力和增溶PCBs的影响.结果表明,醇-PCBs油的界面张力与醇浓度、醇含碳原子数均呈负相关,甲醇、乙醇、异丙醇的最佳解吸浓度分别为70%、55%、40%,最佳解吸效率达90%以上;Triton X-100-PCBs油界面张力与Triton X-100浓度呈负相关,Triton X-100浓度低于3 000 mg/L时复配10%乙醇、10%异丙醇比单一Triton X-100振荡洗脱效率低,Triton X-100浓度在3 000～7 500 mg/L时3组差异不大,Triton X-100浓度为10 000 mg/L时单一、10%乙醇、10%异丙醇TritonX-100溶液解吸效率分别为80.9%、90.36%、89.36%.表明醇类单一使用对降低界面张力与增溶均有很好的效果,但需要其体积分数达40%以上;醇类复配Triton X-100时醇的存在弱化了Triton X-100增溶和降低界面张力的作用,乙醇与异丙醇弱化作用差异性不大,当Triton X-100浓度高于3 000 mg/L时,弱化作用不显著.     

固相萃取-气相色谱/质谱法测定水中四乙基铅的方法研究

建立了固相萃取-GC/MS法测定水中四乙基铅的方法。对固相萃取条件、气相色谱条件和质谱条件进行了优化,并对实际水样进行了测定。方法检出限为0.004μg/L,水样的加标回收率为71.5%～103.2%,精密度(RSD,n=6)为4.4%～11.6%。方法准确、灵敏可靠、干扰小、适应范围广,可以满足水中痕量四乙基铅的分析要求。     

流动注射在线萃取石墨炉原子吸收法测定芦荟中的铅

以APDC/MIBK为萃取系统 ,流动注射在线液 液萃取石墨炉原子吸收光谱法测定芦荟样品中痕量铅 ,对萃取条件 ,流路参数及共存组分的干扰等均进行了探讨。本法的测定精密度 (RSD)为 3 .74% ,检出限 (3σ)为 3 .2× 1 0 - 1 2 g ,加标回收率为 93 %～ 99%。测定结果令人满意。     

阻抑催化动力学光度法测定水体中的痕量镍

研究了在pH9.2硼砂介质中,镍(II)对过氧化氢氧化溴甲酚紫褪色反应具有阻抑作用,聚乙二醇-200(PEG-200)对此反应体系有活化作用,据此建立了阻抑动力学光度法测定痕量镍(II)的新方法。试验考察了反应介质种类和用量、活化剂种类和用量、反应温度、反应时间、共存组分等因素的影响,确定了最佳试验条件。该方法的测定波长为590nm;活化剂为PEG-200;反应温度为沸水浴;反应时间为14min;线性范围为1.7×10-6g/L～1.4×10-4g/L;检出限为1.7×10-6g/L。所建方法用于环境水体中痕量镍(II)的测定,最大相对标准偏差为3.27%,加标回收率为95.5%～104.5%;所建方法与火焰原子吸收光谱法进行了对比试验,方法相对误差小于6.50%。     

固相萃取-红外分光光度法测定水中的总油

建立了固相萃取(SPE)-红外分光光度测定水中总油的方法,并对固相萃取条件进行了优化,实验表明,对于1L添加2mg标准油的水样,其总油的回收率为86%-93%,多次重复实验测定的相对标准偏差为2.9%(n=6)。     

纳米TiO_2胶体分离富集水样中痕量镍研究

利用纳米二氧化钛胶体比表面积大,吸附能力强以及吸附离子沉积后又很容易转化为胶体的特点,提出用纳米二氧化钛胶体富集水样中痕量镍。系统研究了胶体纳米二氧化钛对N(iII)的吸附行为,考察了吸附时间、酸度以及共存离子对吸附行为的影响。研究结果表明:在优化条件下,纳米二氧化钛胶体对N(iII)的吸附率可达99%以上。建立了纳米二氧化钛胶体分离富集与火焰原子吸收光谱联用测定水样中痕量镍的方法。该法检出限(3σ)为4.17μg/L,相对标准偏差(RSD)为2.8%;并且由于纳米二氧化钛胶体吸附镍后不需要脱附,分析过程简便、快速;用于实际水样中痕量镍的测定,结果满意。     

沉淀分离富集-分光光度法测定海水中痕量活性磷酸盐

十六烷基三甲基溴化铵(cetyltrimethylammonium bromide,CTAB)可与磷钼蓝(phosphomolybdenum blue,PMB)生成水难溶的PMB-CTAB离子缔合物沉淀,从而分离富集水溶液中的PMB。该沉淀易溶于硫酸乙醇溶液,溶液在700 nm有强吸收,基于此建立了沉淀分离富集-分光光度法测定海水中痕量活性磷酸盐的新方法。对溶剂酸度、试剂用量、反应时间与温度等实验参数进行了优化选择,并考察了盐度对测定结果的影响。实验结果表明,PMB可被CTAB有效地定量沉淀;盐度在15~45范围内,对测定结果无影响。在优化的实验条件下,以盐度为35的人工海水为基底,做空白加P标实验,方法的线性范围为0.30~8.00μg/L,平均回收率为95.0%,方法检测限为0.10μg/L。对实际海水中痕量活性磷酸盐进行测定,相对标准偏差(RSD)为4.4%~7.1%,与广泛采用的MAGIC法比较,置信度为99%时结果无显著差异。新方法具有消耗试样体积少、测定速度快等优点。     

SPME-GC/MS法测定垃圾渗沥液中双酚A

建立了固相微萃取-气相色谱质谱联用法测定垃圾渗沥液中双酚A的方法,并用于广州大田山垃圾渗沥液中双酚A含量的测定。对影响萃取的参数进行了优化,实验选用涂层厚度为85μm聚丙烯酸酯(PA)萃取纤维,在搅拌速度为1200r/min、NaCl浓度为20%、pH2.0和室温条件下萃取60min。方法的线性范围为0.1～100μg/L,检出限为0.03μg/L,精密度为6.6%。应用本方法监测了广州大田山垃圾渗沥液中BPA的含量在生物法处理过程中的变化情况。     

表面活性剂及其组合洗脱污染土壤中的硫丹

采用序批实验和并行解吸法,研究了添加和不添加Na2SiO3两种情况下,非离子表面活性剂和阴/非离子混合表面活性剂对污染老化土壤中α-、β-硫丹的洗脱效果与动力学特征.结果表明,不添加Na2SiO3时,α-、β-硫丹的洗脱率顺序为Tween80/SDS>Tween 80>Triton X-100.Triton X-100/SDS在100～500 mg·L-1和800～1 000 mg·L-1时的洗脱率分别低于和高于相应浓度的Triton X-100;添加Na2SiO3后,硫丹的洗脱率顺序为Tween 80/SDS>Tween 80>Triton X-100/SDS>Triton X-100,4种洗脱模式对硫丹的洗脱能力均显著提高,其中α-硫丹的洗脱率分别是不加Na2SiO3的1.17～2.73、1.87～4.02、1.85～6.56和1.87～2.85倍.硫丹的洗脱过程可用4参数2室一级动力学模型描述,存在明显的快速洗脱和慢速洗脱阶段;β-硫丹的洗脱速率和洗脱率均低于相应处理的α-硫丹,表明β-硫丹较难从土壤中洗脱;添加Na2SiO3可增大硫丹的快速和慢速洗脱速率常数,减少慢速洗脱的百分率.与其它洗脱模式比较,添加Na2SiO3的Tween 80/SDS能够高效、快速洗脱污染土壤中的硫丹,是一种优良的混合洗脱剂.     

Cloud point extraction coupled with HPLC-UV for the determination of phthalate esters in environmental water samples

A method based on cloud point extraction was developed to determine phthalate esters including di-ethyl-phthalate （DEP）, di- （2-ethylhexyl）-phthalate （DEHP） and di-cyclohexyl-phthalate （DCP） in environmental water samples using high-performance liquid chromatography separation and ultraviolet detection （HPLC-UV）. The non-ionic surfactant Triton X-114 was chosen as extraction solvent. The parameters affecting extraction efficiency, such as concentrations of Triton X-114 and Na2SO4, equilibration temperature, equilibration time and centrifugation time were evaluated and optimized. Under the optimum conditions, the method can achieve preconcentration factors of 35, 88, 111 and detection of limits of 2.0, 3.8, 1.0 ng/ml for DEP, DEHP and DCP in 10-ml water sample, respectively. The proposed method was successfully applied to the determination of trace amount of phathalate esters in effluent water of the wastewater treatment plant and the lixivium of plastic fragments.     

阳-非离子混合表面活性剂对沉积物吸附硝基苯的影响

研究了非离子表面活性剂Triton X-100、阳离子表面活性剂氯化十六烷基吡啶(CPC)及其混合物在沉积物上的吸附行为,探讨了它们对沉积物吸附硝基苯的影响.结果表明,CPC和Triton X-100在沉积物上的吸附等温线均为非线性,吸附量随着平衡浓度的增加急剧增加,并迅速达到最大吸附量.低浓度CPC能明显增加Triton X-100在沉积物上的吸附,而高浓度的CPC则显著降低Triton X-100在沉积物上的吸附.Triton X-100略微降低CPC在沉积物上的吸附.在表面活性剂浓度较低的实际环境中,无论是阳离子或非离子表面活性剂,将主要被土壤或沉积物吸附并固定.硝基苯在沉积物上的吸附等温线为线性.CPC和Triton X-100促进沉积物对硝基苯的吸附,CPC-Triton X-100混合表面活性剂溶液能进一步增强沉积物对硝基苯的吸附.因此,阳离子和非离子混合表面活性剂可增强土壤或沉积物对有机污染物的吸附固定能力,也可以用来制备有机膨润土以提高其吸附处理废水的性能.     

Effects of nonionic surfactant Triton X-100 on the laccase-catalyzed conversion of bisphenol A

The laccase-catalyzed conversion of bisphenol A (BPA) in aqueous solutions was studied in the absence and presence of nonionic surfactant Triton X-100. It was found that the addition of Triton X-100 into the reaction system increased the conversion of BPA, especially near the critical micelle concentration of Triton X-100. Also it was found that the stability of laccase was greatly improved in the presence of TritonX-100. Studies on the endogenous fluorescence emission of laccase indicated that there existed an interaction between Triton X-100 and laccase, which was beneficial to folding and stabilizating of laccase. The binding of Triton X-100 to the laccase surface also mitigated the inactivation e ect caused by the free radicals and polymerization products. Under otherwise identical conditions, a lower dosage of laccase was needed for the higher conversion of BPA in the presence of Triton X-100.     

Effects of surfactants on graphene oxide nanoparticles transport in saturated porous media

Transport behaviors of graphene oxide nanoparticles (GONPs) in saturated porous media were examined as a function of the presence and concentration of anionic surfactant (SDBS) and non-ionic surfactant (Triton X-100) under different ionic strength (IS). The results showed that the GONPs were retained obviously in the sand columns at both IS of 50 and 200 mmol/L, and they were more mobile at lower IS. The presence and concentration of surfactants could enhance the GONP transport, particularly as observed at higher IS. It was interesting to see that the GONP transport was surfactant type dependent, and SDBS was more effective to facilitate GONP transport than Triton X-100 in our experimental conditions. The advection–dispersion–retention numerical modeling followed this trend and depicted the difference quantitatively. Derjaguin–Landau–Verwey–Overbeek (DLVO) interaction calculations also were performed to interpret these effects, indicating that secondary minimum deposition was critical in this study.     

液固比对土壤洗涤去除多环芳烃效果的影响

液固比是影响土壤洗涤污染物去除率的重要因素.以Triton X-100和Tween-80为洗涤剂,采用洗涤去除率(R)、吸附损失率(Vs)和新定义的指标增溶百分比(SP)分析液固比对土壤洗涤去除目标多环芳烃效果的影响.结果表明,液固比对土壤洗涤去除多环芳烃效果影响显著.R随液固比增加呈非线性形式增大,液固比10∶1后R增长变缓.同一液固比时,洗涤去除率Triton X-100>Tween-80.Vs随液固比增加显著减少,液固比10∶1后逐渐变缓.同一液固比时,吸附损失率Triton X-100相似文献   

胶团强化超滤处理含镍废水

胶团强化超滤(MEUF)是一种高效分离水中金属离子的技术。以无机陶瓷膜为媒介,采用胶团强化超滤法处理含镍废水,考察膜孔径,表面活性剂十二烷基硫酸钠(SDS)浓度、镍离子浓度、pH值等因素对胶团强化超滤过程的影响。实验结果表明:膜孔径、SDS浓度、pH值对镍离子截留率有显著影响。当废水温度为20℃,操作压力为0.15 MPa,膜孔径为20 nm,SDS浓度为6.0 mmol/L时超滤效果最好;在此条件下,镍离子的截留率达99.25%,膜通量为89.65 L/(m2.h)。     

Sorption and transport studies of cetyl trimethylammonium bromide (CTAB) and Triton X-100 in clayey soil

Surfactants are soil washing agents and facilitators for subsurface remediation of hydrocarbon spills.It is important to understand the sorption and transport behavior of surfactants for enhanced soil remediation.The adsorption and desorption isotherms of cetyl trimethylammonium bromide (CTAB) and Triton X-100 with sand and kaolinite have been quantified.Kaolinite clay had the highest sorption capacity compared to blasting sand.Transport parameters such as diffusion coefficient (D) and retardation factor (R) of the above mentioned surfactant solutions were determined in clayey soils (82.5% sand and 17.5% kaolinite mixture) with near zero and 0.1 g/L ionic strength.NaCl was used as the electrolyte solution.Convection-Diffusion equation was used to model the breakthrough curves of the surfactants.Bromide ion was chosen as the tracer material in order to characterize the column.CTAB and Triton X-100 were used to flush the perchloroethylene (PCE) contaminated soil.The effectiveness of CTAB and Triton X-100 in flushing the PCE from the contaminated soil was quantified.     

Mobilization of arsenic from contaminated sediment by anionic and nonionic surfactants

The increasing manufacture of surfactants and their wide application in industry,agriculture and household detergents have resulted in large amounts of surfactant residuals being discharged into water and distributed into sediment. Surfactants have the potential to enhance arsenic mobility, leading to risks to the environment and even human beings. In this study, batch and column experiments were conducted to investigate arsenic mobilization from contaminated sediment by the commercial anionic surfactants sodium dodecylbenzenesulfonate(SDBS), sodium dodecyl sulfate(SDS), sodium laureth sulfate(AES)and nonionic surfactants phenyl-polyethylene glycol(Triton X-100) and polyethylene glycol sorbitan monooleate(Tween-80). The ability of surfactants to mobilize arsenic followed the order AES SDBS SDS ≈ Triton X-100 Tween 80. Arsenic mobilization by AES and Triton X-100 increased greatly with the increase of surfactant concentration and p H, while arsenic release by SDBS, SDS and Tween-80 slightly increased. The divalent ion Ca~(2+) caused greater reduction of arsenic mobilization than Na~+. Sequential extraction experiments showed that the main fraction of arsenic mobilized was the specifically adsorbed fraction. Solid phase extraction showed that arsenate(As(V)) was the main species mobilized by surfactants,accounting for 65.05%–77.68% of the total mobilized arsenic. The mobilization of arsenic was positively correlated with the mobilization of iron species. The main fraction of mobilized arsenic was the dissolved fraction, accounting for 70% of total mobilized arsenic.     

Sorption of Triton X-100 on soil organic matter fractions：Kinetics and isotherms

Kinetics and isotherms of Triton X-100 sorption on soil,base-extracted soil(BE),humic acid (HA) and humin (HM) were investigated respectively to get better understanding on characteristics of the surfactant sorptiun onto different soil organic matters(SOMs).It was demonstrated that the kinetics results could be satisfactorily described by the pseudo-second order model.The half of the time to reach equilibrium(t1/2) for different sorbents followed the sequence of soil>HA>BE>HM.Furthermore,the calculated equilibrium sorption capacity(Ceq) was found in the sequence of HA>BE>HM>soil,which agreed well with the experimental results.The isotherms of Triton X-100 sorption on soil and HA could be well described by the S-type isotherm,but BE and HM by the L-type.The isotherms of all the four sorbents were found reasonably fitted to the Langmuir equation.The Kd value,defined as the ratio of Triton X-100 in sorbent and in the equilibrium solution for given concentrations,generally followed the order of HM>HA>soil>BE.Separated HM and HA showed high affinity for Triton X-100,but the HA and HM in soil and BE were tightly bounded by the minerals.Thus,the HA on the soil surface might dominate the sorption,whereas the bounded HM would play a key role upon the surfactants being penetrated inside the soil.     

Solubilization and degradation of perchloroethylene （PCE） in cationic and nonionic surfactant solutions

Solubilization of perchloroethylene (PCE) in a nonionic (Triton X-100) and a cationic (cetyltrimethylammonium bromide (CTAB)) surfactant solutions and the degradation of surfactant solubilized PCE using fine to nanosize Fe and bi-metallic Fe-Ni particles were investigated. Micelle partition coefficients (Km) and molar solubility ratio (MSR) for PCE in 10 g/L of surfactant solutions have been quantified and the solubility of PCE (100 mg/L in water) in the surfactant solutions increased by about ten fold. Of the two surfactants studied, Triton X-100 solubilized the higher amount of PCE per gram of surfactant. To degrade solubilized PCE, both iron and bimetallic Fe-Ni particles were used in continuously stirred batch reactors. The iron and bi-metallic particles were synthesized using the solution method and the particles were characterized using the SEM, EDS, TEM and XRD. The PCE solubilized up to 500 mg/L in both surfactant solutions were totally degraded at various rates by 200 g/L of bi-metallic Fe-Ni particles in less than 20 hr, which is the highest concentration of PCE degraded in the shortest time compared to data in the literature. The degradations of PCE solubilized in surfactant solutions were represented by nonlinear kinetic relationships which depended on the type of surfactant used for solubilizing the PCE.