电化学消毒法对水中大肠杆菌的灭活特性

本研究通过电化学消毒小试装置,系统考察了电极板材料、极板间距、p H、水温、Na Cl浓度等因素对水中大肠杆菌CGMCC 1.3373灭活效果的影响,并进一步考察了电化学消毒对抗生素抗性大肠杆菌CGMCC 1.1595的灭活效果及其抗性变化.结果发现,在相同的电化学消毒条件下,阳极采用钌铱涂层的钛电极板的灭活效果显著优于铅涂层和铱钽涂层电极板,并且极板间距为50 mm时灭活率最高.进一步研究表明,电化学消毒法对大肠杆菌的灭活率随水的p H升高而降低,随水温和Na Cl浓度升高而升高.在相同消毒条件下,电化学法对四环素抗性大肠杆菌的灭活率显著低于普通大肠杆菌.消毒后存活的抗性菌对四环素、青霉素、氯霉素的抗性,随消毒时间延长呈现先下降后上升的规律.     

非平衡等离子体联合技术降解甲苯气体

采用了自制的纳米钛酸钡基介电材料作为催化剂,以电工陶瓷拉西环作为载体,利用介质阻挡放电产生的非平衡态等离子体对常压下流动态含甲苯的空气进行处理,研究了电场强度、流速、初始浓度及不同填料情况下甲苯的降解及臭氧产生情况,初步探讨了等离子体催化降解甲苯的机理,并进行了产物分析.实验结果表明,电场强度小于13kV·cm-1时,甲苯降解率和臭氧产生浓度随电场强度的提高而上升,随气速和初始浓度的增加而降低;不同填料下降解率及臭氧浓度由大到小排序为有催化剂填料、普通填料、无填料,有催化剂存在时(电场强度为14kV·cm-1,流速为0.3 m3·h-1,甲苯浓度为600 mg·L-1),甲苯降解率最高可达95%.当电场强度>13kV·cm-1时,臭氧浓度因受到过量的高能电子攻击而发生分解.表现为臭氧浓度随电场强度的继续增加而降低.因此,电场强度为13kV·cm-1时,产生的臭氧浓度最高.     

污水紫外线消毒工艺的影响因素研究

以大肠杆菌为受试菌种,研究了紫外线光强、配水水质及微生物因素对紫外线消毒的影响.在所选取的紫外光强范围内(0.044～0.163mW/cm²),光强对紫外线灭活大肠杆菌的去除率影响不大.水质(浊度、铁和腐殖酸等)对水样的吸光度及紫外线穿透率都有明显的影响;但是对大肠杆菌的灭活率影响不显著;当紫外线剂量增加时,这种影响逐渐变小到可以忽略.微生物的初始浓度对紫外线对微生物的灭活率有影响,微生物初始浓度越大,灭活率越高;对于不同初始浓度,紫外线灭活后存活的微生物数量比较接近.     

氯气灭活饮用水中隐孢子虫的影响因素

应用荧光活体染色法研究Cl2在水体中杀灭隐孢子虫的效果,并探讨投加量、作用时间、浑浊度、pH值、温度、有机物含量等对Cl2灭活隐孢子虫效果的影响规律,找出最佳投加量和作用时间.结果显示,隐孢子虫浓度1×106个/mL,温度22℃,pH7.0,浊度为1.0NTU,氯气投加量大于6.3mg/L,反应时间360min,隐孢子虫的灭活率可以达到预期灭活效果(灭活率﹥99.0%).隐孢子虫的灭活率与氯气投加量和作用时间成正相关;灭活率随着浑浊度增加逐渐下降,浑浊度0.1~20.0NTU范围内,氯气投加量为6.3mg/L,作用时间大于900min,即可保证隐孢子虫的灭活率符合预定要求;在弱酸性条件下氯气灭活隐孢子虫能力强于碱性条件,反应温度(5.0~35.0℃)范围内,隐孢子虫的灭活率与温度成正相关;HA浓度0~10.0mg/L,作用时间为360min时,灭活率随有机物浓度增加而降低.当作用时间为900min时,水中隐孢子虫的灭活率均大于99.0%.     

臭氧灭活水中铜绿微囊藻影响因素研究

为研究臭氧在水体中杀灭铜绿微囊藻的效果,利用中性红染色法探讨了不同因素(臭氧投量、作用时间、pH值、温度、浑浊度、初始藻细胞密度等)对臭氧灭活铜绿微囊藻效果的影响.结果表明,随着臭氧投量和作用时间的延长,藻灭活率明显增加.当浑浊度0.5~20NTU,温度5~35℃, pH值6.0~9.0,同时浊度越低,灭活效果越好;随温度上升,臭氧灭活铜绿微囊藻能力减弱;碱性较酸性条件下臭氧杀灭铜绿微囊藻的能力更强.藻样初始浓度对杀藻效果影响较大,细胞密度增大,杀藻效果急剧下降.当初始藻细胞密度为1.0×107cells/L,臭氧投量为2.0mg/L,作用时间40min以上时,在饮用水消毒的浊度、温度、pH值范围内,铜绿微囊藻的灭活率在99.0%以上,繁殖能力降低到0.     

浸没式膜生物反应器中气含率的研究

通过对浸没式膜生物反应器中总平均气相含率、下降区气含率和上升区气含率的测量和研究,实验表明:反应器运行的适宜工况流量为:100~300 m3/h之间,曝气量:2.5~7.5 m3/h;验证了静压差法测量气含率的方法在膜生物反应器中的适用性;根据测量数据分析得出膜生物反应器中总平均气含率随曝气量的增大而增加,整个下降区气含率及计算得到的上升区气含率都稳定增大,但下降区内部每段气含率呈现余弦曲线的变化规律。     

圆孔多孔板水力空化杀灭大肠杆菌的实验研究

在以圆形孔口多孔板为空化空蚀发生器的水力空化装置中,对含有大肠杆菌的水样进行灭菌处理.通过检测大肠杆菌的灭菌率,研究了水力空化对水中大肠杆菌的灭活效果.分析了大肠杆菌初始浓度,水流空化数,孔口流速,孔口排布,孔口数量,孔口大小,空化空蚀作用时间等参数对灭菌效果的影响.试验结果表明：提高流速,降低空化数,选取适当的初始浓度,延长空化空蚀作用时间,增加孔口数量,减小孔口大小以及改进孔口排布可以进一步提高大肠杆菌的杀灭率.水力空化的空化空蚀作用能够杀灭水中的大肠杆菌,是一种饮用水消毒的新技术.     

HSL好氧生物流化床中水力学特性的研究

实验研究了HSL好氧生物流化床在不同曝气方式（填料、填装率、曝气水深、微孔曝气与单孔曝气等）下的流化曝气量,结果表明：流化曝气量随填料填装率增加而增大,当填料填装率超过90％,增大曝气量已不可能使填料完全流化;填料流化曝气量先随曝气水深增大而减小,后又随之增加;采用单孔曝气较微孔曝气易实现填料流化,但此时充氧效率会受到一定影响。     

快速混合法氯化消毒及其效果研究

本文提出了以固定混合器作为促进混合效果装置的快速混合法,并以E.Coli作为指示微生物、液氯作为消毒剂进行了研究。结果表明,均匀快速而剧烈的初始混合作用,可大大改善灭菌效果。在短至5秒的接触时间内即可达到99.99％以上的灭活效率。投氯量和接触时间对E.Coli灭活率的影响随混合程度的提高而减弱。与传统法相比,灭活率可提高100倍以上,投氯量可下降4—8倍,接触时间可大大缩短。     

悬浮颗粒对污水氯消毒“拖尾”现象的影响

利用动力学方法研究了悬浮颗粒对二级出水氯消毒灭活大肠杆菌"拖尾"现象的影响规律.SS浓度越高,消毒拖尾区出现越早,灭活率越低.双对数回归对比表明,SS与灭活速度线性相关,浓度从6mg/L升高至85mg/L,总的灭活速度降低约10倍.采用多次拟合统计分析发现,SS浓度在10～55mg/L范围内,悬浮颗粒浓度与拖尾区起始时间及起始点对数灭活率线性相关(R20.99).在此范围内随SS浓度升高,拖尾起始点的时间由330min降低到55min,对数灭活率由5.8降低至0.8.有效去除SS不仅能够提高拖尾区灭活率,也可以提高消毒效率,降低消毒池的投资和运行费用.高氯投量及低pH值均能一定程度提高"拖尾"区灭活率.     

Removal of phenol by activated alumina bed in pulsed high-voltage electric field

A new process for removing the pollutants in aqueous solution-activated alumina bed in pulsed high-voltage electric field was investigated for the removal of phenol under different conditions. The experimental results indicated the increase in removal rate with increasing applied voltage, increasing pH value of the solution, aeration, and adding Fe^2＋. The removal rate of phenol could reach 72.1% when air aeration flow rate was 1200 ml/min, and 88.2% when 0.05 mmol/L Fe^2＋ was added into the solution under the conditions of applied voltage 25 kV, initial phenol concentration of 5 mg/L, and initial pH value 5.5. The addition of sodium carbonate reduced the phenol removal rate. In the pulsed high-voltage electric field, local discharge occurred at the surface of activated alumina, which promoted phenol degradation in the thin water film. At the same time, the space-time distribution of gas-liquid phases was more uniform and the contact areas of the activated species generated from the discharge and the pollutant molecules were much wider due to the effect of the activated alumina bed. The synthetical effects of the pulsed high-voltage electric field and the activated alumina particles accelerated phenol degradation.     

Escherichia coli inactivation by pressurized CO2 treatment methods at room temperature: Critical issues

This study aims to increase the inactivation efficiency of CO_2 against Escherichia coli under mild conditions to facilitate the application of pressurized CO_2 technology in water disinfection. Based on an aerating-cycling apparatus, three different treatment methods(continuous aeration, continuous reflux, and simultaneous aeration and reflux) were compared for the same temperature, pressure(0.3–0.7 MPa), initial concentration, and exposure time(25 min). The simultaneous aeration and reflux treatment(combined method) was shown to be the best method under optimum conditions, which were determined to be 0.7 MPa, room temperature, and an exposure time of 10 min. This treatment achieved 5.1-log reduction after 25 min of treatment at the pressure of 0.3 MPa and 5.73-log reduction after 10 min at 0.7 MPa. Log reductions of 4.4 and 5.0 occurred at the end of continuous aeration and continuous reflux treatments at 0.7 MPa, respectively.Scanning electron microscopy(SEM) images suggested that cells were ruptured after the simultaneous aeration and reflux treatment and the continuous reflux treatment. The increase of the solubilization rate of CO_2 due to intense hydraulic conditions led to a rapid inactivation effect. It was found that the reduction of intracellular p H caused by CO_2 led to a more lethal bactericidal effect.     

流光放电等离子体污水消毒灭菌

采用流光放电等离子体技术,研究放电电压、大肠杆菌初始浓度、反应器类型对大肠杆菌灭杀的影响,并将流光放电等离子体与臭氧灭菌进行效果对比。结果表明:当在水槽装置中,处理温度为室温,大肠杆菌初始浓度为480 000个/L,放电时间为45 min,水样体积V=50 L,气量Q=8 m3/h,放电电压为30 k V,电流I=11 m A时大肠杆菌的去除率达到99%。流光放电等离子体与臭氧去除污水中大肠杆菌的能力都较强,与臭氧灭菌相,比流光放电等离子体杀菌经济成本低廉许多。     

Sterilization of Escherichia coli cells by the application of pulsed magnetic field

The inactivation of microorganisms by pulsed magnetic field was studied. It was improved that the application of electromagnetic pulses evidently causes a lethal effect on E. coil cells suspended in phosphate buffer solution Na2HPO4/NaH2 PO4 (0.334/0.867mmol/L). Experimental results indicated that the survivability( N/N0 ; where N0 and N are the number of cells survived per milliliter before and after electromagnetic pulses application, respectively) of E. coil decreased with magnetic field intensity B and treatment time t. It was also found that the medium temperatures, the frequencies of pulse f, and the initial bacterial cell concentrations have determinate influences in destruction of E. coil cells by the application of magnetic pulses. The application of an magnetic intensity B = 160 mT at pulses frequency f= 62 kHz and treatment time t = 16 h result in a considerable destruction levels of E. coil cells ( N/N0=10^-4). Possible mechanisms involved in sterilization of the magnetic field treatment were discussed. In order to shorten the treatment time, many groups of parallel inductive coil were used. The practicability test showed that the treatment time was shortened to 4 h with the application of three groups of parallel coil when the survivability of E. coli cells was less than 0.01%; and the power consumption was about 0.2 kWh/m^3 .     

二氧化氯对不同微生物的灭活特性及其对群落结构特征的影响

二氧化氯是一种性能优良、应用广泛的消毒剂,可通过破坏细胞或病毒的组成结构、阻碍细胞代谢等方式实现微生物灭活。在自配水条件下,以二氧化氯投加量×消毒时间计算,二氧化氯剂量在15（mg·min）/L时,可实现对常见病毒（包括肠病毒71型、大肠杆菌噬菌体MS2等）3 log以上灭活率,在60（mg·min）/L时,可实现对常见细菌（包括大肠杆菌、金黄色葡萄球菌等）1.5 log以上灭活率,但灭活隐孢子虫卵则需要更高的剂量（如1.9 log灭活率可能需约600（mg·min）/L剂量）;在实际污水厂进水中,30（mg·min）/L二氧化氯剂量只能分别实现0.8 log和0.5 log的大肠杆菌和总大肠菌群灭活率。二氧化氯消毒效果随温度升高显著提升,对于不同微生物,pH的变化对二氧化氯消毒效果的影响可能存在不同,而水中的有机物通常会因消耗二氧化氯而降低消毒效果,但在自然水体中也存在由于天然有机物可能的影响导致消毒效果优于自配水的情况。关于二氧化氯消毒后细菌群落结构的变化研究不多,仅有少量研究涉及市政污水、再生水、饮用水等。二氧化氯消毒一定时间后,悬浮态和生物膜上的微生物均可能出现再生长现象,但再生长过程中这些残生细菌的群落结构变化及其生长分泌特性仍有待研究。     

石墨相氮化碳光催化灭活水中多重耐药菌研究

研究了光辐照和基于石墨相氮化碳（g-C₃N₄）光催化对二级出水中1株四环素和氨苄西林抗性多重耐药菌E.coli CGMCC 1.1595的灭活效果.结果表明,汞灯辐照功率（100/300/500W）和辐照强度越高,其灭活效率相对越高,在500W汞灯60min辐照条件下,紫外长波（UVA）-可见光（300~579nm）对该多重耐药菌的灭活率为0.41log;基于g-C₃N₄的光催化对其灭活率为1.31log.相比未加g-C₃N₄催化剂的光辐照灭菌,在UVA-可见光条件下g-C₃N₄对其灭活率的贡献为61%~69%;在可见光条件下g-C₃N₄对其灭活率的贡献达到60%~79%.在UVA-可见光g-C₃N₄光催化灭活E.coli CGMCC 1.1595反应体系中,活性氧自由基和电子空穴的活跃程度为：·OH > ·O₂^- > H₂O₂ > h⁺ > ¹O₂,·OH为该光催化体系的主要活性物质,其次是·O₂^-和H₂O₂.     

混凝-臭氧催化氧化联合工艺处理成品油洗舱废水

将经过混凝沉淀预处理后的成品油洗舱废水,进行臭氧催化氧化深度处理,并研究处理时间、臭氧曝气量以及活性炭填充率对COD去除率的影响。结果表明:当处理时间为1.0 h,臭氧曝气量为1.0 g/(L.h),活性炭填充率为60%时,处理效果显著,COD去除率为50%～60%。     

大气压纳秒负脉冲放电对水中大肠杆菌的灭活

采用自行研制的喷嘴-板-筒式反应器,研究了大气压纳秒负脉冲空气放电对水中大肠杆菌（Escherichia coli, E.coli）灭菌率的影响因素及规律。实验中空气自放电喷嘴电极进入反应器,气流带动放电生成的活性粒子流到达并作用于水中大肠杆菌。研究结果表明:本实验装置可有效实现对水中大肠杆菌的灭活,灭菌率随着放电电压和脉冲重复频率的增加、放电处理时间的延长而升高;随着鼓气速率的增大先增大后减小;随着喷嘴电极直径的增加先减小后增大。当采用1.30 mm喷嘴电极,在脉冲峰值电压为-32 kV、重复频率80 Hz,鼓气速率为80 mL/min时,连续放电处理12 min,灭菌率达到91%。     

Inactivated properties of activated carbon-supported TiO2 nanoparticles for bacteria and kinetic study

The activated carbon-supported TiO2 nanoparticles(TiO2/AC)were prepared by a properly controlled sol-gel method.The effects of activated carbons(AC)support on inactivated properties of TiO2 nanoparticles were evaluated by photocatalytic inactivation experiments of Escherichia coli.The key factors affecting the inactivation effciency were investigated,including electric power of lamp, temperature,and pH values.The results show that the TiO2/AC composites have high inactivation properties of E.coli in compari...