Tool Path Planning for Avoiding Exit Burrs

Milling exit burrs usually form along the edges of a workpiece when the tool leaves the part while removing stock material. One of the most efficient methods for minimizing exit burrs is to prevent the tool from exiting the workpiece during material removal. This paper describes a systematic framework to generate tool paths that always enter a part, which is not a thin structure, in a planar milling operation. Three distinct tool exit conditions are analyzed for polygonal parts. A test criterion is then proposed to examine the occurrence of tool exits. For each condition, a tool path planning scheme is developed to avoid tool exits. These schemes are proved to be effective using the test criterion. This work is integrated into a networked manufacturing environment as a burr agent. Test parts are cut to demonstrate that this framework enhances edge quality by minimizing tool exits.     

An Approach to Theoretical Modeling and Simulation of Face Milling Forces

A new approach to theoretical modeling and simulation of face milling forces is presented. The present approach is based on a predictive machining theory in which machining characteristic factors in continuous cutting with a single-point cutting tool can be predicted from the workpiece material properties, tool geometry, and cutting conditions. The action of a milling cutter is considered as the simultaneous work of a number of single-point cutting tools, and the milling forces are predicted from input data of workpiece material properties, cutter parameters and tooth geometry, cutting condition, cutter and workpiece vibration structure parameters, and types of milling. A predictive force model for face milling is developed using this approach. In the model, the workpiece material properties are considered as functions of strain, strain rate, and temperature. The ratio of cutter tooth engagement over milling is taken into account for the determination of temperature in the cutting region. Cutter runout is included in the modeling for the chip load. The relative displacement between the cutter and workpiece due to the cutter and workpiece vibration is also included in the modeling to consider the effect on the undeformed chip thickness. A milling force simulation system has been developed using the model, and face milling experimental tests have been conducted to verify the simulation system. It is shown that the simulation results agree well with experimental results.     

Process capability study of laser assisted micro milling of a hard-to-machine material

Laser assisted micro milling (LAMM) is capable of generating three-dimensional micro scale features in hard-to-machine materials. This paper compares the process capability of LAMM with conventional micro milling of a hardened tool steel. In particular, the potential advantages of LAMM over micro milling with respect to cutting forces, tool wear, material removal rate, burr formation and surface roughness are investigated when micro milling hardened A2 tool steel (62 HRC). The results show that LAMM has significant advantages over micro milling, especially in terms of cutting forces, material removal rate and tool wear. The average reduction in the resultant cutting force is found to be up to 69% with laser assist. In addition, tool wear is found to be substantially less with laser assist even when the material removal rates are increased by a factor of six over the tool manufacturer recommended cutting conditions.     

Burr Formation in Drilling Intersecting Holes with Machinable Austempered Ductile Iron (MADI™)

This paper presents an investigation of the burr formation for a new material, machinable austempered ductile iron (MADI™), while drilling intersecting holes in the presence of tool wear. A factorial design is used to evaluate the effects of drill point angle and helix angle as well as feed rate and cutting speed on the burr width and height at both curved and flat hole exit conditions. The result indicates the presence of a complex interrelationship among these four variables, particularly the interaction between helix and point angle and its influence on drill corner wear and, hence, burr geometry. Burrs are considerably larger at the flat exit condition. Further experiments were conducted in a central composite design scheme to develop second-order polynomial models of the burr width and height. The result suggests that burr width and height can be reduced by using larger helix and smaller point angles. The result further demonstrates that the somewhat unique work-hardening characteristic of MADI™ during machining can lead to smaller burrs when smaller chiploads are used, regardless of the drill helix and point angles.     

Effect of Tool Edge Geometry on Workpiece Subsurface Deformation and Through-Thickness Residual Stresses for Hard Turning of AISI 52100 Steel

An experimental investigation was conducted to determine the effect of tool cutting edge geometry on workpiece subsurface deformation and through-thickness residual stresses for finish hard turning of through-hardened AISI 52100 steel. Polycrystalline cubic boron nitride (PCBN) inserts with “up-sharp” edges, edge hones, and chamfers were used as the cutting tools in this study. Examination of the workpiece microstructure reveals that large edge hone tools produce substantial subsurface plastic flow. Flow is not observed when turning with small edge hone tools or chamfered tools, and the workpiece microstructure appears random for these cases. Examination of through-thickness residual stresses shows that large edge hone tools produce deeper, more compressive residual stresses than are produced by small edge hone tools or chamfered tools. Explanations for these effects are offered based on assumed contact conditions between the tool and workpiece.     

The effect of spindle speed,feed-rate and machining time to the surface roughness and burr formation of Aluminum Alloy 1100 in micro-milling operation

This paper describes the characteristics and the cutting parameters performance of spindle speeds (n, rpm) and feed-rates (f, mm/s) during three interval ranges of machining times (t, minutes) with respect to the surface roughness and burr formation, by using a miniaturized micro-milling machine. Flat end-mill tools that have two-flutes, made of solid carbide with Mega-T coated, with 0.2 mm in diameter were used to cut Aluminum Alloy AA1100. The causal relationship among spindle speeds, feed-rates, and machining times toward the surface roughness was analyzed using a statistical method ANOVA. It is found that the feed-rate (f) and machining time (t) contribute significantly to the surface roughness. Lower feed-rate would produce better surface roughness. However, when machining time is transformed into total cut length, it is known that a higher feed-rate, that consequently giving more productive machining since produce more cut length, would not degrade surface quality and tool life significantly. Burr occurrence on machined work pieces was analyzed using SEM. The average sizes of top burr for each cutting parameter selection were analyzed to find the relation between the cutting parameters and burr formation. In this research, bottom burr was found. It is formed in a longer machining time compare the formation of top burr, entrance burr and exit burr. Burr formation is significantly affected by the tool condition, which is degrading during the machining process. This knowledge of appropriate cutting parameter selection and actual tool condition would be an important consideration when planning a micro-milling process to produce a product with minimum burr.     

Innovative micro hole machining with minimum burr formation by the use of newly developed micro compound tool

The study focuses on the efforts for minimization of burr formation and improvement of hole surface roughness in micro through-hole machining. It deals with the development of micro compound tool which is consisting of a micro flat drill as the drilling part and a micro diamond-electroplated-grinding part for hole finishing. The finishing diameters of each drilling and grinding parts of the fabricated micro compound tool are 90 μm and 100 μm, respectively. The study focuses mainly on the effect of drill point angle and ultrasonic vibration applied during micro hole machining to the hole entrance and exit burrs formation. The used workpiece is made of stainless steel (SUS304) with a thickness of 100 μm. From the experiment, it was found that the tool having drill point angle of 118° resulted in a smaller burr formation although hole machining was conducted for 600 holes. Furthermore, the application of ultrasonic vibration during hole machining could improve the performance of the developed micro compound tool and decreased the burr size, especially the exit burr.     

Analytical process damping stability prediction

This paper describes an analytical solution for turning and milling stability that includes process damping effects. Comparisons between the new analytical solution, time-domain simulation, and experiment are provided. The velocity-dependent process damping model applied in the analysis relies on a single coefficient similar to the specific cutting force approach to modeling cutting force. The process damping coefficient is identified experimentally using a flexure-based machining setup for a selected tool-workpiece pair (carbide insert-AISI 1018 steel). The effects of tool wear and cutting edge relief angle are also evaluated. It is shown that a smaller relief angle or higher wear results in increased process damping and improved stability at low spindle speeds.     

Ball end milling mechanistic model based on a voxel-based geometric representation and a ray casting technique

Prediction of machining forces involved in complex geometry can be valuable information for machine shops. This paper presents a mechanistic cutting force simulation model for ball end milling processes, using ray casting and voxel representation methods used in 3D computer graphics field. Using this method, instantaneous uncut chip cross sectional areas can be extracted, which can be used in cutting pressure coefficient extraction and machining simulation including machining forces and geometry of the workpiece. The major advantage of the proposed scheme is that it can simulate milling processes with arbitrary cutting tool geometry on a workpiece with complex geometry, using an algorithm with constant time complexity. A series of cutting experiments were carried out to validate the model.     

Shear cutting and counter shear cutting of sandwich materials

New lightweight sandwich materials challenge existing forming processes as well as following process steps. As such the manufacturing potential of shear cutting has to be evaluated. Two cutting methods are compared. Method commonly used is shear-cutting within one stroke engaged, the other one is known as counter-shear cutting, which uses two strokes.The challenges of cutting sandwich materials are variation of hole diameter within the different layers, fraying of the textiles, deformation of the hole contour and burr formation. These effects occur in conventional shear cutting as the intermediate layer and the lower sheet metal are cut by the scrap of the upper sheet instead of the cutting punch.The following methodology included shear cutting with closed cutting edge i.e. cutting of holes into five different sandwich materials. The sandwiches exemplarily represent multiple kinds of possible material designs. For instance, aluminum and steel face sheets, different thicknesses of intermediate layers and different intermediate layers materials such as integrated textile fibers have been used. Adequate cutting parameters such as die clearance and the use of a blank holder have been determined. To achieve good results a stiff machine design with good guidance and precise control of punch position was crucial.Observations of conventional shear cutting revealed the need of small cutting clearance of 4%. High burnish area is possible for the upper face sheet due to the superimposed force by the lower face sheet. The major conclusion depicted that high cutting quality of sandwich materials requires counter shear cutting. Hence, the roll-over of the lower sheet facing the intermediate layer, the burnish area at the lower sheet, good cutting quality of the fibers improve significantly and burr formation is avoided completely. Summarized this paper provides cutting parameters for sandwich materials based on experimental work.     

Measurement of tool internal temperatures in the tool–chip contact region by embedded micro thin film thermocouples

Sensors capable of providing fast and reliable feedback signals for monitoring and control of existing and emerging machining processes are an important research topic, that has quickly gained academic and industrial interest in recent years. Generally, high-precision machining processes are very sensitive to variation in local machining conditions at the tool–workpiece interface and lack a thorough understanding of fundamental thermomechanical phenomena. Existing sensors to monitor the machining conditions are not suitable for robust in-process control as they are either destructively embedded and/or do not possess the necessary spatial and temporal resolution to monitor local tool internal temperatures during machining at the cutting tip/edge effectively. This paper presents a novel approach for assessing transient tool internal temperature fields in the close vicinity of less than 300 μm of the tool cutting edge. A revised array layout of 10 micro thin film micro thermocouples, fabricated using adapted semiconductor microfabrication methods, has been embedded into polycrystalline cubic boron nitride (PCBN) cutting inserts by means of a modified diffusion bonding technique. Scanning electron microscopy was used to examine material interactions at the bonding interface and to determine optimal bonding parameters. Sensor performance was statically and dynamically characterized. They show good linearity, sensitivity and very fast response time. Initial machining tests on aluminum alloys are described herein. The tests have been performed to demonstrate the functionality and reliability of tool embedded thin film sensors, and are part of a feasibility study with the ultimate goal of applying the instrumented insert in hard machining operations. The microsensor array was used for the acquisition of tool internal temperature profiles very close to the cutting tip. The influence of varying cutting parameters on transient tool internal temperature profiles was measured and discussed. With further study, the described instrumented cutting inserts could provide more valuable insight into the process physics and could improve various aspects of machining processes, e.g. reliability, tool life, and workpiece quality.     

Robust prediction of chatter stability in milling based on the analytical chatter stability

A major obstacle that limits the productivity in machining operations is the presence of machine tool chatter. Machining is a dynamic process and chatter behavior depends upon a number of different aspects including spindle speeds, material properties, tool geometry, and even the location of tool respect to the rest of machine. Many of the traditional models used to predict chatter stability lobes assume that parameters such as natural frequency, stiffness, and cutting coefficients remain constant. In reality, these parameters vary and they affect the chatter stability. The uncertainty in these parameters can be taken into consideration by employing the robust stability theory into a two degree of freedom milling model. Utilizing the Edge theorem and the Zero Exclusion condition, a robust chatter stability model, based on the analytical chatter stability milling model, is developed. This improves the reliability compared to the projected pseudo single degree of freedom model. The method is verified experimentally for milling operations while considering a changing natural frequency and cutting coefficient.     

Analysis of machined surface quality in a single-pass of ball-end milling on Inconel 718

The ball-end milling process is widely used for generating three-dimensional sculptured surfaces with definite curvature. In such cases, variation of surface properties along the machined surface curvatures is not well understood. Therefore, this paper reports the effect of machining parameters on the quality of surface obtained in a single-pass of a ball-end milling cutter with varying chip cross-sectional area. This situation is analogous to generation of free form cavities, pockets, and round fillets on mould surfaces. The machined surfaces show formation of distinct bands as a function of instantaneous machining parameters along the periphery of cutting tool edge, chip compression and instantaneous shear angle. A distinct variation is also observed in the measured values of surface roughness and micro-hardness in these regions. The maximum surface roughness is observed near the tool tip region on the machined surface. The minimum surface roughness is obtained in the stable cutting zone and it increases towards the periphery of the cutter. Similar segmentation was observed on the deformed chips, which could be correlated with the width of bands on the machined surfaces. The sub-surface quality analysis in terms of micro-hardness helped define machining affected zone (MAZ). The parametric effects on the machining induced shear and residual stresses have also been evaluated.     

Experimental Evaluation of Cutter Orientation When Ball Nose End Milling Inconel 718™

High-speed machining (HSM), specifically end milling and ball end cutting, is attracting interest in the aerospace industry for the machining of complex 3D aerofoil surfaces in titanium alloys and nickel-based superalloys. Following a brief introduction on HSM and related aerospace work, the paper reviews published data on the effect of cutter/workpiece orientation, also known as engagement or tilt angle, on tool performance. Such angles are defined as ±β_fN and ±β_f.Experimental work is detailed on the effect of cutter orientation on tool life, cutting forces, chip formation, specific force, and workpiece surface roughness when high-speed ball end milling Inconel 718™. Dry cutting was performed using 8 mm diameter PVD-coated solid carbide cutters with the workpiece mounted at an angle of 45° from the cutter axis.A horizontal downward (-β_fN) cutting orientation provided the best tool life with cut lengths ∼50% longer than for all other directions (+β_fN, +β_f, and –β_f). Evaluation of cutting forces and associated spectrum analysis of results indicated that cutters employed in a horizontal downward direction produced the least vibration. This contributed to improved workpiece surface roughness, with typical mean values of ∼0.4 μm Ra as opposed to ∼1.25 μm Ra when machining in the vertical downward (–β_f) direction.     

Application of Taguchi method to selection of optimal lubrication and cutting conditions in face milling of AlMg3

This paper outlines the Taguchi optimization methodology, which is applied to optimize the cutting parameters in face milling when machining AlMg₃ (EN AW 5754) with HSS (high speed steel) tool under semi-finishing conditions in order to get the best surface roughness and the minimum power consumption. Beside the conventional flood lubrication, the investigations include the minimal quantity lubrication and the dry milling. These environment-friendly cutting techniques are considered two practical ways to the cleaner manufacturing in the context of the sustainable production. The parameters evaluated are the cutting speed, the depth of cut, the feed rate and the cooling lubrication techniques (cutting fluid flow). The appropriate orthogonal array, signal to noise (S/N) ratio and Pareto analysis of variance (ANOVA) are employed to analyze the effect of the mentioned parameters on the good surface finish (surface roughness). This paper illustrates the application of the techniques for single performance characteristics optimization, which employs the weighting factors to each of the S/N ration of the responses to obtain a multi-response S/N ratio for each trial of the orthogonal array and, finally, a single optimal process parameters setting. Using Taguchi method for the design of experiments (DOE), it is investigated the significant influence and the parameters interaction effect with minimum number of trials as compared with a full factorial design.     

Macro-level environmental comparison of near-dry machining and flood machining

This paper focuses on investigating several aspects of the machining process from an ecological perspective, the result being a macro-level analysis. The analysis presented here considers not only the environmental impact of the material removal process itself, but also the impact of the associated processes such as the material preparation, and the scrap processing. A macro-level assessment of the comparative life cycle environmental performance of the near-dry machining (NDM) using TiN-coated carbide tools and the flood machining (FM) is performed by a case study referring to the gear milling. The assessment, using the SimaPro 7.1.5 software and the ecoinvent1.5 database, includes combined Life Cycle Assessment (LCA) of the workpiece material, the scrap processing, the use of lubrication, and the energy consumption.     

Micro dimple milling on cylinder surfaces

The paper presents a micro dimple machining on a cylinder surface with a two-flutes ball end mill. When the cutter axis is inclined and the depth of cut is less than the tool radius, non-cutting time, during which neither of the two cutting edges contacts the workpiece, appears in a rotation of the cutter. The rotation of the workpiece and the feed of the tool are controlled so that the cutting areas do not overlap each other. In order to incline the tool with respect to the tangential direction on the cylinder surface, the tool is located at a position oriented at 45° from the top of the cylinder. An analytical model is presented to control the shapes of the dimples with the cutting parameters. The presented machining is verified in cutting tests with measuring the shape and the profile of the dimples. Pre-machining operations are conducted to have a high cylindricity of the workpiece in longitudinal turning and polishing. The cutter runout of the tool is also eliminated by adjusting the orientation and the position of the tool in the collet chuck with measuring the cutting force. The micro dimples are machined accurately as they are simulated.     

Machining assessment of nano-crystalline hydroxyapatite bio-ceramic

Hydroxyapatite (HAP) is a widely used bio-ceramic in the fields of orthopedics and dentistry. This study investigates the machinability of nano-crystalline HAP (nHAP) bio-ceramic in end milling operations, using uncoated carbide tool under dry cutting conditions. Efforts are focused on the effects of various machining conditions on surface integrity. A first order surface roughness model for the end milling of nHAP was developed using response surface methodology (RSM), relating surface roughness to the cutting parameters: cutting speed, feed, and depth of cut. Model analysis showed that all three cutting parameters have significant effect on surface roughness. However, the current model has limited statistical predictive power and a higher order model is desired. Furthermore, tool wear and chip morphology was studied. Machined surface analysis showed that the surface integrity was good, and material removal was caused by brittle fracture without plastic flow.     

3D numerical investigation of thermally assisted high efficiency ductile machining of nanocrystalline hydroxyapatite

This study investigates the effects of four different variables (initial workpiece temperature, side rake angle, edge radius/feed rate, and nose radius/depth of cut) on ductile regime machining of a bioceramic material known as nanohydroxyapatite (nano-HAP) using 3D numerical simulation. AdvantEdge FEM Version 5.9 is used to conduct turning simulations of the nano-HAP workpiece. Tecplot 360 is used to analyze the results of the simulations. Because the workpiece is thin, the entire workpiece is set to a uniform initial temperature to simulate laser preheating of the material. Initial workpiece temperature, rake angle (side rake angle), edge radius, and nose radius are varied, and the effects of these operating conditions on critical feed are investigated. It is found that critical feed increases as initial workpiece temperature increases, and also as negativity of rake angle increases. For the edge radius, it is concluded that an initial increase causes an increase in critical feed – however, at some value of edge radius, critical feed shows no further increase; for the nose radius, critical feed appears to show no significant dependence.     

Laser cutting of alumina tiles: Heating and stress analysis

Laser cutting of alumina tiles is carried out, and the temperature and stress fields developed in the cutting section are predicted numerically using ABAQUS finite element code. The morphological changes along the cut edge surfaces are examined using the optical and scanning electron microscopes. The residual stress formed in the cutting section is obtained after incorporating the XRD technique. The residual stress predicted is compared with the experimental data. It is found that the residual stress predicted agrees well with the experimental results. The dross attachment at the kerf exit is observed, which is associated with the high melting temperature of the workpiece.