聚合铝混凝过程研究:不同形态硅酸的影响作用

研究了不同形态硅酸对聚合铝混凝过程的影响作用 .实验结果表明经预制形成的具有不同形态分布组成的硅酸与聚合铝 ,在投加后相互间发生了十分复杂的物理化学作用 ,并受溶液pH值的影响 ,从而最终决定了混凝效果 .反应过程中所生成的形态产物及其物化特征 ,很大程度上取决于聚合铝碱化度以及所投加的Si Al比 .其中碱化度越高 ,最终产物所带电荷越高 .而不同硅酸所起影响作用分别取决于聚合程度 ,在与聚合铝反应过程中表现出一定的规律性 .单体硅酸与单体铝迅速发生较强的络合作用 ,抑制了多聚水解铝阳离子的形成 .聚合硅酸则倾向于与聚合铝形态相互作用形成一定的胶状化合物 ,从而在溶液中稳定存在 .对于胶体硅酸 ,在聚合铝作用下迅速凝聚形成更大的聚集体 ,在颗粒物间架桥形成粗大的絮体 .所得结果对混凝机理的解释与复合混凝剂的发展提供了一定的参考作用     

混凝微界面过程研究与进展:AOM颗/粒物-IPF水-溶液相互作用的重要性

颗粒物微界面的物理化学过程在混凝工艺中起着十分重要的决定作用.有关界面过程化学的研究构成了混凝技术研究与发展的重要内容和理论基础.本文仅以颗粒物/AOM-IPF-水溶液的相互作用为例,从水体颗粒物的稳定性、高效纳米絮凝剂的研究、微界面形态与过程以及混凝作用机理等诸方面,对该领域的研究与进展加以系统介绍.     

IPF混凝过程的定量计算模式(I):PCNM的应用

水处理过程IPF的混凝作用机理研究逐渐向半定量乃至定量化发展 .以典型IPF 颗粒物 水溶液体系的相互作用为例 ,对PCNM模式的应用从混凝剂的形态分布、投药量、pH以及其它影响因素加以研究讨论 .结果表明 ,经适当改进的PCNM能够较好地预测聚合铝的混凝特征 ,实验结果与模式预测值基本吻合 .对PCNM模式中存在的若干问题亦进行了详细讨论     

水体中Cr (Ⅵ)对不同混凝剂混凝过程的影响

研究了工业废水中Cr(Ⅵ)在不同颗粒物浓度影响下对不同铝形态混凝剂的影响过程,通过考察浊度去除率以及出水余铝、余铬浓度甄别了混凝效率,并利用混凝过程中剩余p H值、Zeta电位以及絮体性质揭示水中Cr(Ⅵ)在不同浊度下的混凝机制.结果表明,在低浊度条件下,Cr(Ⅵ)对高聚合态Alb的混凝过程具有较大影响,而对低聚合态Ala无明显影响;在高浊度条件下,水中浊度较高时颗粒物会吸附部分Cr(Ⅵ)从而降低其与Alb之间的作用.Alb在混凝中主要发挥电中和作用,其对颗粒的脱稳和絮体的再生具有重要的作用,Ala水解形成的部分Alc在混凝中主要发挥架桥网捕作用,其对絮体的生产和强度因子具有重要作用.同时Cr(Ⅵ)的存在会增强Al13絮体的强度因子,但其消耗了部分正电荷会导致絮体恢复因子降低.     

混凝沉淀过程中铝系混凝剂的形态转化规律

研究了模拟配水中硫酸铝和氯化铝2种传统铝凝聚剂和2种聚合氯化铝(PAC)絮凝剂在混凝过程中的形态转化规律以及原水浊度和溶解性有机碳(DOC)对残余铝形态分布的影响.结果表明,在低浊体系中,投加铝系混凝剂是导致出水余铝升高的主要原因;但在高浊体系中,铝系混凝剂,尤其是聚合铝具有一定的除铝功能;混凝沉淀过程中传统铝凝聚剂的残余铝总量明显高于聚合铝混凝剂的残余铝总量;聚合铝混凝剂的残余铝全部为悬浮态铝,传统铝混凝剂的残余铝中还存在着胶体态铝和溶解态铝.原水浊度和DOC浓度增加,会提高残余铝中胶体态铝和溶解态铝的含量.     

聚合氯化铁-聚(环氧氯丙烷-二甲胺)复合絮凝剂在模拟水处理中的混凝特性研究

制备出一系列具有不同聚合氯化铁(PFC)的碱化度(B)、不同聚(环氧氯丙烷-二甲胺)[P(EPI-DMA)]质量分数[ω(E)]和黏度(η)的PFC-P(EPI-DMA)复合混凝剂,并将其用于模拟染料废水和模拟天然地表水的絮凝脱色处理,对比探讨了ω(E)、η和B对PFC-P(EPI-DMA)中铁的形态分布及其混凝效果的影响,以及混凝作用机制.结果表明,复合絮凝剂中铁的有效形态含量随ω(E)的增大而不断降低;η=850 mPa.s时,复合混凝剂中铁的有效形态含量最高;随B值的增大,Feb含量先增大后减少,而Fec含量逐渐增大.一定程度上使用预水解程度较低、有机成分黏度较大的PFC-P(EPI-DMA)有利于混凝效果的提高,复合混凝剂中有机成分质量分数对混凝效果的影响则与处理对象有关.在模拟水处理中,复合混凝剂依靠电性中和及架桥吸附能力发挥混凝特性.     

混凝剂的水溶液形态与流动电流的相关特性分析

混凝剂具有多种溶液形态，每种形态对混凝过程的作用不同，因而对流动电流的影响也不同，本通过实验及理论分析，阐述了一般水处理条件下的流动电流检测器（ＳＣＤ）对混凝剂的检测原理，分析了水中混凝剂形态改变过程中流动电流的变化特征，探讨了ＳＣＤ对不同形态混凝剂的响应灵敏度，结果表明，中性条件下铝盐的混凝过程以及三价铁阳离子对流流具有较为灵敏的正增值效果。     

不同铝聚合形态对聚合铝混凝效果的影响

通过氯化铝(铝单体或初聚物形态Ala)、高Alb含量聚合铝(中等聚合形态Alb)、高Alc含量聚合铝(铝溶胶等高聚合形态Alc)和工业PACl(不同聚合度铝的混合形态Alabc)对某水厂沉后水实际水样进行烧杯混凝实验,依据絮体生长状况、浊度、UV254、颗粒数和过滤指数等参数综合评价不同铝形态的混凝作用效果,从而得出铝的最佳混凝形态.结果表明,高Alb含量聚合铝对浊度去除较好;而高Alc含量聚合铝对于颗粒物和UV254的去除效果较佳.     

IPF-PACl混凝动力学研究:形态组成的重要性

应用一种新近发展起来的基于浊度脉动测定的混凝监测技术结合经改进的传统混凝烧杯试验方法 ,对具有不同形态组成的聚合铝 (PACl)产品的混凝性能进行了细致地研究 .结果表明 :聚合铝不同形态在混凝过程中起着十分重要的影响作用 .混凝反应途径随预制后产品形态分布的不同而得到改变 .其中 ,A1b 是起电中和作用的主要形态 .PACl中A1b 的含量越高 ,其电中和能力越强 ,因此大大增加了颗粒间的碰撞效率 .然而 ,PAC2 5则表现出更为优越的混凝性能 ,在于其中A1c 含量的不同而引发“静电簇”混凝效应 ,导致混凝的快速动力学过程     

聚合铝的水解形态对混凝过程中磷分布转化的影响

用碱化度不同的混凝剂对水体进行混凝处理,对混凝前后水体中磷的含量、形态分布以及藻类可利用性等进行了研究.结果表明,不同碱化度的混凝剂除磷效果不同,对水体中磷形态分布的影响差别显著;Ala在混凝剂去除磷实验过程中起重要作用,碱化度越低的混凝剂除磷率越高,PACl0除磷效果最好.随着混凝剂(PACl0)投量的增加,水体中溶...     

聚合氯化铝中纳米Al13形态的混凝效应

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al13形态,用透光率脉动检测技术并结合絮凝效能和Zeta电位测定结果,对纳米Al13形态以及PAC、AlCl3絮凝过程中絮集物形成和增长的变化差异作了对比性研究.结果表明,混凝剂的不同铝形态分布在混凝过程中起着十分重要的作用.Al13形态是在絮凝过程中起电中和作用的主要形态,可以大大增加颗粒间的有效碰撞率,其凝聚速度和所形成絮集物颗粒大小在实验条件下呈现最大值.而对于PAC,其Alc含量较高,可起到吸附架桥和网捕卷扫作用,所以在低投加量表现出较快的絮体增长速率.     

Purification and characterization of Al13 species in coagulant polyaluminum chloride

Nano-Al₁₃ was separated and purified by four methods to investigate its characteristic, and was analyzed by Al-Ferron timed complexation spectrophotometer,²⁷ Al-NMR (nuclear magnetic resonance), and transmission electron microscopy (TEM). Coagulation efficiency of nano-Al₁₃, polyaluminum chloride (PAC), and AlCl₃ in synthetic water were also investigated by jar test. The dynamic process and aggregation state of kaolin suspensions coagulating with nano-Al₁₃, PAC, and AlCl₃ were also investigated. The experimental results indicated that the efficiency of gel column chromatography method was the highest for separating PAC solution with low Al concentration. Ethanol and acetone method was simple and could separated PAC solution with different Al concentrations, while silicon alkylation white block column chromatography method could separate PAC solution only with low Al concentration. The SO₄²−/Ba²⁺ displacement method could separate PAC solution with high Al concentration, but extra inorganic cation and anion could be introduced into the solution during the separation. The coagulation efficiency and dynamic experimental results showed that nano- Al₁₃ with a high positive-charged species was the main species of electric neutralization in coagulation process, and it could reduce the turbidity and increase the effective particles collision rate efficiently in coagulation process. Its coagulation speed and the particle size of coagulant formed were of greatest value in this study.     

The influence of particle size and concentration combined with pH on coagulation mechanisms

In order to evaluate the influence of particle size and particle concentration on the coagulation process, two kinds of particle suspensions, nanoparticles and microparticles,were employed to investigate the effect of particle size on coagulation mechanisms with varying coagulation parameters. Results showed that it is easier for nanoparticles to cause self-aggregation because of Brownian motion, while interception and sedimentation are the mainly physical processes affecting particle transport for microparticles, so they are more stable and disperse more easily. The particle size distribution and particle concentration had distinct influence on the coagulation mechanisms. Under neutral conditions, as the amount of coagulant increased, the coagulation mechanism for nanoparticles changed from charge neutralization to sweep flocculation and the nanoparticles became destabilized, re-stabilized and again destabilized. For microparticles, although the coagulation mechanism was the same as that of nanoparticles, the increased rate of aluminum hydroxide precipitation exceeded the adsorption of incipiently formed soluble alum species, resulting in the disappearance of the re-stabilization zone. Under acidic conditions, Brownian motion dominates for nanoparticles at low particle concentrations, while sweep flocculation is predominant at high particle concentrations. As for microparticles, charge neutralization and sweep flocculation are the mechanisms for low and high particle concentrations respectively.Under alkaline condition, although the mechanisms for both nano-and microparticles are the same, the morphology of flocs and the kinetics of floc formation are different. At low particle concentrations, nanoparticles have larger growth rate and final size of flocs, while at high particle concentrations, nanoparticles have higher fractal dimension and recovery factors.     

颗粒物悬浮体系中聚合铝凝聚絮凝形态表征 (Ⅰ):Al-Feron法的应用研究

应用Ａｌ－Ｆｅｒｒｏｎ法于悬浮体系中聚合铝的形态分布表征,对其中的主要影响因素进行探讨,就不同碱化度聚合铝的形态分析进行实例研究。结果表明,混合方式对Ａｌ－Ｆｅｒｒｏｎ法的应用具有一定的影响作用。比色管混合测得Ａｌａ为２１．５４％,低于磁力搅拌方式结果（２４．５２％,２５．２２％,２５．０６％）。应用磁力搅拌方式可以获取较好的重复性与更多初期反应信息。颗粒物的存在对反应的影响主要取决于其浓度与粒度     

混凝过程中铝与聚合铝水解形态的动力学转化及其稳定性

采用Ｆｅｒｒｏｎ逐时络合比色法，并结合电泳测定研究了混凝过程中氯化铝和聚合氯化铝的水解形态动力学转化及稳定性。结果表明，ＡＣ在混凝过程中所形成的水解形态完全不同于ＰＡＣ的预制水解聚合形态，其电荷及分子量均明显低于聚合铝且不稳定，ＡＣ随混凝条件如投加浓度、ＰＨ和混合时间而变，而ＰＡＣ－２５水解聚合形态不随混凝条件变化，始终保持稳定状态，ＡＣ水解沉淀规律与理论计算相符并形成无定形Ａｌ（ＯＨ）３絮体颗粒     

Al13形态在混凝中的作用机制

从铝的水解形态转化角度考察了铝盐在高碱度和高有机物浓度水体中的混凝行为.结果表明,铝盐的混凝效能是与混凝过程中的Al₁₃含量成正比.高投药量时氯化铝(AlCl₃)既可以有效调节水体pH值又能在混凝过程中原位水解产生较多的Al₁₃形态,因而混凝效能要高于聚合氯化铝(PACl).在铝盐混凝中,调节pH值到6～7之间可以控制铝形态分布从而达到提高混凝效能和减少残留铝的目的.在调节pH值强化混凝的方法中使用传统铝盐的效果要好于无机高分子絮凝剂.     

Removal characteristics of microplastics by Fe-based coagulants during drinking water treatment

Microplastics have caused great concern worldwide recently due to their ubiquitous presence within the marine environment. Up to now, most attention has been paid to their sources, distributions, measurement methods, and especially their eco-toxicological effects. With microplastics being increasingly detected in freshwater, it is urgently necessary to evaluate their behaviors during coagulation and ultrafiltration (UF) processes. Herein, the removal behavior of polyethylene (PE), which is easily suspended in water and is the main component of microplastics, was investigated with commonly used Fe-based salts. Results showed that although higher removal efficiency was induced for smaller PE particles, low PE removal efficiency (below 15%) was observed using the traditional coagulation process, and was little influenced by water characteristics. In comparison to solution pH, PAM addition played a more important role in increasing the removal efficiency, especially anionic PAM at high dosage (with efficiency up to 90.9%). The main reason was ascribed to the dense floc formation and high adsorption ability because of the positively charged Fe-based flocs under neutral conditions. For ultrafiltration, although PE particles could be completely rejected, slight membrane fouling was caused owing to their large particle size. The membrane flux decreased after coagulation; however, the membrane fouling was less severe than that induced by flocs alone due to the heterogeneous nature of the cake layer caused by PE, even at high dosages of Fe-based salts. Based on the behavior exhibited during coagulation and ultrafiltration, we believe these findings will have potential application in drinking water treatment.     

Computer simulation of the coagulation of suspended solids — The applicability of the Müller–Smoluchowski theory

The results of studies carried out using a computer programme simulating the coagulation of suspensions containing spherical sol particles and spherical coagulant particles are reported.The influence of the degree of dispersion of the system on the coagulation reaction kinetics was investigated. The obtained results of kinetic studies were tested in the light of classical Müller–Smoluchowski equations. The influence of the physical properties of the coagulant,such as size, density and mass, on the coagulation rate was tested. It was found that within the range described in this paper, the rate of the simulated coagulation process fulfils both the kinetic equation of a first-order reaction, and the kinetic equation of a second-order reaction.Within the tested range, a significant influence of the mass and size of the coagulant on the coagulation rate was ascertained. The kinetic Müller–Smoluchowski dependence is fulfilled in a broader range of the degree of dispersion, when the coagulant particle mass and the sol particle mass are equal. When the particle mass increases with an increase in the particle radius, the coagulation rate increases faster that it would result from the Müller's dependence.     

Hydrolyzed Al(Ⅲ) clusters: Speciation stability of nano-Al13

Pure nano-Al13 and aggregates at various concentrations were prepared to examine the particle size effect of coagulation with inorganic polymer fiocculant. The property and stability of various species formed were characterized using Infrared, 27Al-NMR,photo correlation spectroscopy (PCS), and Ferron assay. Results showed that concentration and temperature exhibited different roles on the stability of Al13. The quantity of Alb species analyzed by ferron assay in the initial aging period corresponded well with that of Al13, which has been confirmed in a dimension range of 1-2 nm by PCS. Al13 solutions at high concentrations (0.5-2.11 mol/L)were observed to undergo further aggregation with aging. The aggregates with a wide particle size distribution would contribute to the disappeared/decreased Al13 basis on the 27Al-NMR spectrum, whereas a part of Al13 would still remain as Alb. At low concentrations,Al13 solution was quite stable at normal temperature, but lost its stability quickly when heating to 90°C.