溴离子和溴酸盐活性炭竞争吸附及溴酸盐生成影响

采用3种活性炭对水体中溴离子和溴酸盐的吸附去除规律进行了考察.结果表明,单吸附条件下溴离子和溴酸盐的吸附去除效率分别达到69%和88%以上,双吸附质条件时溴离子去除率减少到10%.溴酸盐去除率为60%以上;有机物与溴酸盐之间存在竞争吸附关系,AC-400的孔径分布条件更适合于有机物的吸附过程.而不利于溴酸盐的吸附,在低浓度平衡溶液条件下(ce＜72 mg·L-1),AC-100对有机物的吸附能力较高,在溶液平衡浓度72mg·L-1＜ce＜211 mg·L-1条件时,AC-150对有机物的吸附能力较强,影响程度取决于活性炭比表面积和粒度分布等因素;溴酸盐的去除效率同时受到水体中氨含量和pH的影响,氨含量超过200μg/L以上溴酸盐减少量变化不显著,较低pH值溴酸盐生成量较少.     

改性壳聚糖季铵盐的研制及其对高氯酸盐的吸附研究

通过将壳聚糖季铵盐改性以实现固定化,并用于水体中ClO 4-的吸附去除,研究了改性过程相关工艺参数对产物吸附能力的影响,考察了产物的吸附和再生性能.结果表明,戊二醛的交联性能优于甲醛和环氧氯丙烷的交联性能,戊二醛的最佳投加量为6.82%,最佳的反应温度为45℃,pH值在3～12之间交联反应均能很好地进行,从而实现壳聚糖...     

Pb(II) removal from water using Fe-coated bamboo charcoal with the assistance of microwaves

Bamboo charcoal(BC) was used as starting material to prepare iron-modified bamboo charcoal(Fe-MBC) by its impregnation in FeCl 3 and HNO 3 solutions simultaneously,followed by microwave heating.The material can be used as an adsorbent for Pb(Ⅱ) contaminants removal in water.The composites were prepared with Fe molar concentration of 0.5,1.0 and 2.0 mol/L and characterized by means of N 2 adsorption-desorption isotherms,X-ray diffraction spectroscopy(XRD),scanning electron microscopy coupled with energy dispersive X-ray spectrometry(SEM-EDS),Fourier transform infrared(FT-IR) and point of zero charge(pH pzc) measurements.Nitrogen adsorption analyses showed that the BET specific surface area and total pore volume increased with iron impregnation.The adsorbent with Fe molar concentration of 2 mol/L(2Fe-MBC) exhibited the highest surface area and produced the best pore structure.The Pb(Ⅱ) adsorption process of 2Fe-MBC and BC were evaluated in batch experiments and 2Fe-MBC showed an excellent adsorption capability for removal Pb(Ⅱ).The adsorption of Pb(Ⅱ) strongly depended on solution pH,with maximum values at pH 5.0.The ionic strength had a significant effect on the adsorption at pH < 6.0.The adsorption isotherms followed the Langmuir isotherm model well,and the maximum adsorption capacity for Pb(Ⅱ) was 200.38 mg/g for 2Fe-MBC.The adsorption processes were well fitted by a pseudo second-order kinetic model.Thermodynamic parameters showed that the adsorption of Pb(Ⅱ) onto Fe-MBC was feasible,spontaneous,and exothermic under the studied conditions,and the ion exchange mechanism played an significant role.These results have important implications for the design of low-cost and effective adsorbents in the removal of Pb(Ⅱ) from wastewater.     

竹炭吸附去除糖蜜酒精废水中COD的研究

通过实验研究了竹炭类型、粒度、投加量、吸附时间以及初始浓度等因素对竹炭吸附去除糖蜜酒精废水中COD效果的影响。结果表明,高温竹炭的吸附效果优于中温竹炭;竹炭粒径越小,废水COD去除效果越好;废水COD去除率随着吸附时间的增大而增加;废水的初始COD浓度越小,COD去除率越大。正交实验表明,废水中COD的去除的最佳条件为,在选用粒度为65～80目的高温竹炭条件下,投加量为1.5g/50mL,水样稀释1倍,振荡时间为1.5h。     

High phosphate removal using La(OH)3 loaded chitosan based composites and mechanistic study

Our present study was to prepare a biomass-supported adsorbents with high adsorptive capacity and high selectivity to prevent the accelerated eutrophication in water body. To this end, different metal hydroxide (La, Zr and Fe) first was successfully loaded on chitosan microspheres. Then the quaternary ammonium group with different content was introduced into the adsorbent by polymerization. By comparison of adsorption properties, chitosan-La(OH)₃-quaternary ammonium-20% (CS-La-N-20%) has strong adsorption to phosphate (160 mg/g) by immobilizing nano-sized La(OH)₃ within a quaternary-aminated chitosan and it maintain high adsorption in the presence of salt ions. The pH results indicated that the CS-La-N-20% would effectively sequestrate phosphate over a wide pH range between 3 and 7 without significant La³⁺ leaching. What's more, adsorption capacity on the introduce of positively charged quanternary-aminated groups was significantly higher than that of the unmodified adsorbents at alkaline conditions. The column adsorption capacity reached 1300 bed volumes (BV) when phosphate concentration decreased until 0.5 mg/L at 6 BV/hr. The column adsorption/desorption reveals that no significant capacity loss is observed, indicating excellent stability and repeated use property. Characterizations revealed that phosphate adsorption on CS-La-N-20% through ligand exchange (impregnated nano-La(OH)₃) and electrostatic attraction (positively charged quanternary-aminated groups). All the results suggested that CS-La-N-20% can serve as a promising adsorbent for preferable phosphate removal in realistic application.     

竹碳吸附苯类化合物的研究

文章利用二硫化碳萃取方法根据气相色谱分析结果,研究了竹碳对于室内空气中苯污染物的吸附,并比较了不同粒径对于吸附的影响。     

Aminobenzenesulfonamide functionalized SBA-15 nanoporous molecular sieve: A new and promising adsorbent for preconcentration of lead and copper ions

A rapid method for the extraction and monitoring of nanogram level of Pb²⁺ and Cu²⁺ ions using uniform silanized mesopor (SBA-15) functionalized with aminobenzenesulfonamide groups and flame atomic absorption spectrometry (FAAS) is presented. Aminobenzenesulfonamide functionalized SBA-15 was synthesized according to procedure in the literature and the presence of organic groups in the silica framework was demonstrated by FT-IR spectra. The functionalized product showed the BET surface area 110 m²/g and pore diameter 5.1 nm, based on adsorption-desorption of N₂ at 77 K. The effect of several variables such as (amount of adsorbent, stirring time, pH and presence of other ions in the medium) has been studied. Lead and copper were completely extracted at pH greater than 3 after stirring for 10 min. The maximum capacity of the adsorbent was found to be 191.3 ± 1.4 and 155.0 ± 1.0 μg of lead and copper ions/mg functionalized SBA-15, respectively. The preconcentration factor of the method was found to be 200. The detection limit of the technique was 3.4 and 0.4 ng/mL for Pb²⁺ and Cu²⁺, respectively. The applications of this methodology for real samples were examined by various water type, black tea and pepper samples.     

Environmental factors affecting degradation of perfluorooctanoic acid (PFOA) by In2O3 nanoparticles

Nanophotocatalysts have shown great potential for degrading poly- and perfluorinated substances (PFAS). In light of the fact that most of these catalysts were studied in pure water, this study was designed to elucidate effects from common environmental factors on decomposing and defluorinating perfluorooctanoic acid (PFOA) by In₂O₃ nanoparticles. Results from this work demonstrated that among the seven parameters, pH, sulfate, chloride, H₂O₂, In₂O₃ dose, NOM and O₂, the first four had statistically significant negative effects on PFOA degradation. Since PFOA is a strong acid, the best condition leading to the highest PFOA removal was identified for two pH ranges. When pH was between 4 and 8, the optimal condition was: pH = 4.2; sulfate = 5.00 mg/L; chloride = 20.43 mg/L; H₂O₂ = 0 mmol/L. Under this condition, PFOA decomposition and defluorination were 55.22 and 23.56%, respectively. When pH was between 2 and 6, the optimal condition was: pH = 2; sulfate = 5.00 mg/L; chloride = 27.31 mg/L; H₂O₂ = 0 mmol/L. With this condition, the modeled PFOA decomposition was 97.59% with a defluorination of approximately 100%. These predicted results were all confirmed by experimental data. Thus, In₂O₃ nanoparticles can be used for degrading PFOA in aqueous solutions. This approach works best when the target contaminated water contains low concentrations of NOM, sulfate and chloride and at a low pH.     

Degradation kinetics and mechanism of trace nitrobenzene by granular activated carbon enhanced microwave/hydrogen peroxide system

The kinetics of the degradation of trace nitrobenzene (NB) by a granular activated carbon (GAC) enhanced microwave (MW)/hydrogen peroxide (H₂O₂) system was studied. Effects of pH, NB initial concentration and tert-butyl alcohol on the removal efficiency were examined. It was found that the reaction rate fits well to first-order reaction kinetics in the MW/GAC/H₂O₂ process. Moreover, GAC greatly enhanced the degradation rate of NB in water. Under a given condition (MW power 300 W, H₂O₂ dosage 10 mg/L, pH 6.85 and temperature (60±5)℃), the degradation rate of NB was 0.05214 min^-1 when 4 g/L GAC was added. In general, alkaline pH was better for NB degradation; however, the optimum pH was 8.0 in the tested pH value range of 4.0-12.0. At H₂O₂ dosage of 10 mg/L and GAC dosage of 4 g/L, the removal of NB was decreased with increasing initial concentrations of NB, indicating that a low initial concentration was beneficial for the degradation of NB. These results indicated that the MW/GAC/H₂O₂ process was effective for trace NB degradation in water. Gas chromatography-mass spectrometry analysis indicated that a hydroxyl radical addition reaction and dehydrogenation reaction enhanced NB degradation.     

Cr(VI) removal from aqueous solution with bamboo charcoal chemically modified by iron and cobalt with the assistance of microwave

Bamboo charcoal (BC) was used as starting material to prepare Co-Fe binary oxideloaded adsorbent (Co-Fe-MBC) through its impregnation in Co(NO3)2 , FeCl3 and HNO3 solutions simultaneously, followed by microwave heating. The low-cost composite was characterized and used as an adsorbent for Cr(VI) removal from water. The results showed that a cobalt and iron binary oxide (CoFe2O4 ) was uniformly formed on the BC through redox reactions. The composite exhibited higher surface area (331 m2/g) than that of BC or BC loaded with Fe alone (Fe-MBC). The adsorption of Cr(VI) strongly depended on solution pH, temperature and ionic strength. The adsorption isotherms followed the Langmuir isotherm model well, and the maximum adsorption capacities for Cr(VI) at 288 K and pH 5.0 were 35.7 and 51.7 mg/g for Fe-MBC and Co-Fe-MBC, respectively. The adsorption processes were well fitted by the pseudo second-order kinetic model. Thermodynamic parameters showed that the adsorption of Cr(VI) onto both adsorbents was feasible, spontaneous, and exothermic under the studied conditions. The spent Co-Fe-MBC could be readily regenerated for reuse.     

Comparison of different combined treatment processes to address the source water with high concentration of natural organic matter during snowmelt period

The source water in one forest region of the Northeast China had very high natural organic matter (NOM) concentration and heavy color during snowmelt period. The efficiency of five combined treatment processes was compared to address the high concentration of NOM and the mechanisms were also analyzed. Conventional treatment can hardly remove dissolved organic carbon (DOC) in the source water. KMnO₄ pre-oxidization could improve the DOC removal to 22.0%. Post activated carbon adsorption improved the DOC removal of conventional treatment to 28.8%. The non-sufficient NOM removal could be attributed to the dominance of large molecular weight organic matters in raw water, which cannot be adsorbed by the micropore upon activated carbon. O₃ + activated carbon treatment are another available technology for eliminating the color and UV₂₅₄ in water. However, its performance of DOC removal was only 36.4%, which could not satisfy the requirement for organicmatter. The limited ozone dosage is not sufficient to mineralize the high concentration of NOM. Magnetic ion-exchange resin combined with conventional treatment could remove 96.2% of color, 96.0% of UV₂₅₄ and 87.1% of DOC, enabling effluents to meet the drinking water quality standard. The high removal efficiency could be explained by the negative charge on the surface of NOM which benefits the static adsorption of NOM on the anion exchange resin. The results indicated that magnetic ion-exchange resin combined with conventional treatment is the best available technology to remove high concentration of NOM.     

A laboratory scale study on arsenic（Ⅴ） removal from aqueous medium using calcined bauxite ore

The present work deals with the As（Ⅴ） removal from an aqueous medium by calcined refractory grade bauxite （CRB） as a function of solution pH, time, As（Ⅴ） concentration and temperature. The residual As（Ⅴ） was lowered from 2 mg/L to below 0.01 mg/L in the optimum pH range 4.0-7.0 using a 5 g/L CRB within 3 h contact time. The adsorption data fits well with Langmuir isotherm and yielded Langmuir monolayer capacity of 1.78 mg As（Ⅴ）/g of CRB at pH 7.0. Presence of anions such as silicate and phosphate decreased As（Ⅴ） adsorption efficiency. An increase temperature resulted a decrease in the amount of As（Ⅴ） adsorbed by 6%. The continuous fixed bed column study showed that at the adsorbent bed depth of 30 cm and residence time of 168 min, the CRB was capable of treating 340 bed volumes of As（V） spiked water （C0 = 2 mg/L） before breakthrough （Ce = 0.01 mg/L）. This solid adsorbent, although not reusable, can be considered for design of adsorption columns as an efficiency arsenic adsorption media.     

High capacity adsorption of antimony in biomass-based composite and its consequential utilization as battery anode

Antimony is more than an emerging pollutant in water but a scare resource. In this study, we report an adsorbent with the record capacity so far from the balanced view of Sb(III) and Sb(V). The composite adsorbent was fabricated by encapsulating hollow Fe₃O₄ nanosphere with the EDTA grafted chitosan, and it has superhigh adsorption capacity of for 657.1 mg/g for Sb(III) and 467.3 mg/g for Sb(V), respectively. The mechanism study reveals that the adsorption of Sb initializes from the Fe₃O₄, propagates along the chitosan with hydrogen bond, and terminates at the inner sphere complex with the EDTA moiety in the adsorbent. In view of the ultra-high adsorption capacity of the adsorbent, the recovered adsorbent that contains abundant (>36.4%) highly dispersed antimony nanoparticles (600-FCSE-Sb) is applied to Li-ion battery anode after reduction. This article provides a new idea for connecting water treatment and electric energy storage.     

Natural organic matter(NOM) removal from surface water by coagulation

IntroductionNaturalorganicmatter(NOM)inriversandlakesisacomplexmixtureofmoleculeswithvaryingmolecularweightandchemicalnatureandoriginatesfromavarietyofsources(degradationofterrestrialandaquaticorganisms,biologicalactivityinthewaterbody,humaninputsetc.).NO…     

新型铁铜铝三元复合氧化物除磷性能与机制研究

采用共沉淀法制备了一种新型铁铜铝三元复合氧化物吸附剂,系统研究了其对磷的吸附行为,并对吸附磷前后的吸附剂进行了表征.吸附实验结果表明,铁铜铝三元复合氧化物对磷具有优异的吸附去除效能,Freundlich吸附等温线模型能更好地拟合其对磷的吸附,最大吸附量为62.6 mg·g-1(pH=7.0),显著高于多数文献报道的磷吸附剂;吸附速率较快,吸附动力学更符合Elovich模型;溶液pH对磷吸附有一定影响,随着pH的升高,磷吸附量降低,离子强度则影响不大;共存阴离子对磷吸附具有抑制作用,影响的大小顺序为SiO_3~(2-)SO_4~(2-)CO_3~(2-)Cl~-,而共存阳离子Ca2+和Mg2+则对磷吸附略有促进作用.Zeta电位、红外谱图(FTIR)和X射线光电子能谱(XPS)表征分析表明,磷在铁铜铝三元复合氧化物表面发生了特性吸附,磷酸根主要通过取代复合氧化物表面的羟基形成内表面络合物而被吸附去除.溶出实验结果表明,当pH在5.0~8.5范围内,Fe~(3+)、Cu~(2+)、Al~(3+)的溶出量均较低.由此可知,铁铜铝三元复合氧化物是一种具有良好应用前景的除磷吸附剂.     

Chemically modified silica gel with 1-{4-[(2-hydroxy-benzylidene)amino]phenyl}ethanone: Synthesis, characterization and application as an efficient and reusable solid phase extractant for selective removal of Zn(II) from mycorrhizal treated fly-ash samples

1-{4-[(2-hydroxy-benzylidene)amino]phenyl}ethanone functionalized silica gel was synthesized and used as a highly efficient, selective and reusable solid phase extractant for separation and preconcentration of trace amount of Zn(II) from environmental matrices. The adsorbent was characterized by fourier transform infrared spectroscopy (FT-IR), elemental analysis,¹³C CPMAS NMR spectroscopy, scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and BET surface area analysis. The dependence of zinc extraction on various analytical parameters such as pH, type and amount of eluent, sample flow rate and interfering ions were investigated in detail. The material exhibited superior adsorption efficiency for Zn(II) with high metal loading capacity of 1.0 mmol/g under optimum conditions. After adsorption, the recovery (> 98%) of metal ions was accomplished using 1.0 mol/L HNO₃ as an eluent. The sorbent was also regenerated by microwave treatment in milder acidic environment (0.1 mol/L HNO₃). The lower detection limit and preconcentration factor of the present method were found out to be 0.04 μg/L and 312.5 respectively. The modified silica surface possessed excellent selectivity for the target analytes and the adsorption/desorption process remained effective for at least ten consecutive cycles. The optimized procedure was successfully implemented for the extraction of Zn(II) from mycorrhizal treated fly ash and pharmaceutical samples with reproducible results.     

改性竹炭生物滤池处理微污染原水的实验研究

以微污染原水中污染物质为去除目标,以廉价和资源丰富的竹炭为原料,通过微波辅助铁钴复合改性,制备了改性竹炭水处理材料,并应用于生物滤池中对微污染原水进行了实验研究。结果表明：在稳定运行条件下改性竹炭生物滤池对浊度、NH4＋－N及CODMn的平均去除率分别为84％、81％和74.5％,且随着运行时间的推移,改性竹炭生物滤池后期出水水质稳定：浊度＜1.0 NTU,NH4＋－N ＜0.5 mg／L,CODMn ＜1.0 mg／L。因此改性竹炭作为生物滤池填料应用于微污染原水处理是可行的。     

Antimony(V) removal from water by iron-zirconium bimetal oxide: Performance and mechanism

A Fe-Zr binary oxide adsorbent has been successfully synthesized using a co-precipitation method. It showed a better performance for antimonate (Sb(V)) removal than zirconium oxide or amorphous ferric oxide. The experimental results showed that the Fe-Zr adsorbent has a capacity of 51 mg/g at an initial Sb(V) concentration of 10 mg/L at pH 7.0. Sb(V) adsorption on the Fe-Zr bimetal oxide is normally an endothermic reaction. Most of the Sb(V) adsorption took place within 3 hr and followed a pseudo second-order rate law. Co-existing anions such as SO₄^2-, NO₃^- and Cl^- had no considerable effects on the Sb(V) removal; PO₃^4- had an inhibitory effect to some extent at high concentration; while CO_₃^2- and SiO₄^4- showed significant inhibitory effects when they existed in high concentrations. The mechanism of Sb(V) adsorption on the adsorbent was investigated using a combination of zeta potential measurements, XPS, Raman, FT-IR observations and SO₄^2- release determination. The ionic strength dependence and zeta potential measurements indicated that inner-sphere surface complexes were formed after Sb(V) adsorption. Raman and XPS observations demonstrated that both Fe-OH and Zr-OH sites at the surface of the Fe-Zr adsorbent play important roles in the Sb(V) adsorption. FT-IR characterization and SO₄^2- release determination further demonstrated that the exchange of SO₄^2- with Sb(V) also could promote the adsorption process. In conclusion, this adsorbent showed high potential for future application in Sb(V) removal from contaminated water.     

质子化交联壳聚糖对水中高氯酸根的吸附特性研究

通过合成质子化交联壳聚糖,采用静态试验方法对水中高氯酸根(ClO4-)的吸附效果及机制进行了研究,考察了pH、温度和初始浓度对吸附过程的影响以及吸附剂的重复使用性能.结果表明,质子化交联壳聚糖吸附ClO4-过程属放热反应;当pH在3.0~6.0之间时,对ClO4-均有较好的吸附作用;随着ClO4-初始浓度的增加,吸附容量增加,当初始浓度为100 mg.L-1时,吸附容量在34.39~37.98 mg.g-1之间;当ClO4-为400 mg.L-1时,吸附容量达128.78 mg.g-1.质子化交联壳聚糖对水中ClO4-的吸附过程符合Langmuir和Freundlich等温吸附模型,ClO4-在质子化交联壳聚糖小球上的吸附过程中化学吸附为速率控制步骤.质子化交联壳聚糖小球可在pH为12.8的NaOH溶液中再生,反复使用10次其吸附容量无明显变化,表现出较好的吸附/解吸性能,这为有效地去除水中的ClO4-提供了新的方法.     

电-Fenton法降解低含盐量反渗透浓缩液中腐植酸

为研究采用碳毡-Pt电-Fenton体系处理模拟低含盐量反渗透浓缩液中的腐植酸的影响因素和降解机制,通过单因素试验,以COD_Cr去除率为评价指标,以Fe2+添加量、通氧量、电流密度、pH为考察因素,探讨了不同条件对电-Fenton体系ρ（H₂O₂）和COD_Cr去除率的影响.结果表明:采用电-Fenton法降解模拟反渗透浓缩液,较低的含盐量有助于COD_Cr的去除,与高含盐量（1 000~2 000 mg/L）相比,在低含盐量（500~1 000 mg/L）条件下COD_Cr去除率提高10%~20%;并且最佳条件下实际电流效率（GCE）达到15.6%,电化学能耗为32 kW·h/kg.最佳反应条件:通氧量为0.3 m3/L,Fe2+添加量为0.1 mmol/L,电流密度为3.5 mA/cm2,pH=3,在该条件下反应180 min时,电-Fenton体系产生的ρ（H₂O₂）为105 mg/L,可使ρ（COD_Cr）由150 mg/L降至16 mg/L,COD_Cr去除率达到90%.研究显示,较宽的pH范围（3~7）内碳毡-Pt电-Fenton体系对腐植酸的降解表现稳定,COD_Cr去除率均达到60%以上.