氢氧化镧掺杂氧化铝去除水体磷酸盐性能研究

为有效去除水体中的磷酸盐,采用沉淀沉积方法合成了氢氧化镧〔La(OH)₃〕掺杂氧化铝(Al₂O₃)的吸附材料La(OH)₃(X)/Al₂O₃〔X表示吸附剂中的La(OH)₃质量含量〕,并对其吸附磷酸盐的性能进行研究. 结果表明:①Al₂O₃和La(OH)₃是吸附剂中磷酸盐的主要结合位点. ②磷酸盐初始浓度为50 mg/L时,La(OH)₃(19)/Al₂O₃吸附剂在初始阶段吸附较快,且在200 min左右达到吸附平衡. La(OH)₃(X)/Al₂O₃吸附剂对磷酸盐的吸附量随着La(OH)₃负载量的提高而升高,其吸附等温线符合Langmuir模型拟合. La(OH)₃(7)/Al₂O₃、La(OH)₃(13)/Al₂O₃、La(OH)₃(19)/Al₂O₃和La(OH)₃(27)/Al₂O₃对磷酸盐的最大吸附量可分别达到25.32、27.40、43.10和53.76 mg/g (以P计). 这表明La(OH)₃掺杂Al₂O₃后为磷酸盐提供更多的活性位点,有效提高了磷酸盐的吸附容量. ③La(OH)₃(19)/Al₂O₃对磷酸盐的吸附量随pH的升高而降低,共存阴离子影响试验表明,La(OH)₃(19)/Al₂O₃对磷酸盐具有较高的吸附选择性. ④经过5次吸附-脱附循环后,La(OH)₃(19)/Al₂O₃表现出稳定的吸附和再生性能,对实际水体磷酸盐的去除试验结果表明其可用于实际水体中磷酸盐的去除. 研究显示,La(OH)₃(19)/Al₂O₃的磷酸盐吸附速率快、吸附容量高、吸附选择性高,具有潜在的应用价值.      

High capacity adsorption of antimony in biomass-based composite and its consequential utilization as battery anode

Antimony is more than an emerging pollutant in water but a scare resource. In this study, we report an adsorbent with the record capacity so far from the balanced view of Sb(III) and Sb(V). The composite adsorbent was fabricated by encapsulating hollow Fe₃O₄ nanosphere with the EDTA grafted chitosan, and it has superhigh adsorption capacity of for 657.1 mg/g for Sb(III) and 467.3 mg/g for Sb(V), respectively. The mechanism study reveals that the adsorption of Sb initializes from the Fe₃O₄, propagates along the chitosan with hydrogen bond, and terminates at the inner sphere complex with the EDTA moiety in the adsorbent. In view of the ultra-high adsorption capacity of the adsorbent, the recovered adsorbent that contains abundant (>36.4%) highly dispersed antimony nanoparticles (600-FCSE-Sb) is applied to Li-ion battery anode after reduction. This article provides a new idea for connecting water treatment and electric energy storage.     

Enhanced CO2 adsorptive performance of PEI/SBA-15 adsorbent using phosphate ester based surfactants as additives

In this study,a series of polyetherimide/SBA-15: 2-D hexagonal P6 mm,Santa Barbara USA(PEI/SBA-15) adsorbents modified by phosphoric ester based surfactants(including tri(2-ethylhexyl)phosphate(TEP),bis(2-ethylhexyl) phosphate(BEP) and trimethyl phosphonoacetate(TMPA))were prepared for CO_2 adsorption.Experimental results indicated that the addition of TEP and BEP had positive effects on CO_2 adsorption capacity over PEI/SBA-15.In particular,the CO_2 adsorption amount could be improved by around 20% for 45PEI–5TEP/SBA-15 compared to the additive-free adsorbent.This could be attributed to the decrease of CO_2 diffusion resistance in the PEI bulk network due to the interactions between TEP and loaded PEI molecules,which was further confirmed by adsorption kinetics results.In addition,it was also found that the cyclic performance of the TEP-modified adsorbent was better than the surfactant-free one.This could be due to two main reasons,based on the results of in situ DRIFT and TG-DSC tests.First and more importantly,adsorbed CO_2 species could be desorbed more rapidly over TEP-modified adsorbent during the thermal desorption process.Furthermore,the enhanced thermal stability after TEP addition ensured lower degradation of amine groups during adsorption/desorption cycles.     

Adsorptive removal of phosphate by the bimetallic hydroxide nanocomposites embedded in pomegranate peel

This study aimed to fabricate new and effective material for the efficiency of phosphate adsorption. Two types of adsorbent materials, the zirconium hydroxides embedded in pomegranate peel (Zr/Peel) and zirconium-lanthanum hydroxides embedded in pomegranate peel (Zr–La/Peel) were developed. Scanning electronic microscopy (SEM), x-ray photoelectron spectroscopy (XPS) and x-ray diffraction (XRD) were evaluated to give insight into the physicochemical properties of these adsorbents. Zr–La/Peel exceeded the adsorption efficiency of Zr/Peel adsorbents in batch adsorption experiments at the same pH level. The peel as a host can strive to have a strong “shielding effect” to increase the steadiness of the entrenched Zr and La elements. La and Zr are hydroxide metals that emit many hydrogen ions during the hydrolysis reaction, which contribute to protonation and electrostatic attraction. The highest adsorption capacity of La–Zr/Peel for phosphate was calculated to be 40.21 mg/g, and pseudo second-order equation is very well fitted for kinetic adsorption. Phosphate adsorption efficiency was reduced by an increase of pH. With the background of coexisting Cl^?, little effect on adsorption efficiency was observed, while adsorption capacities were reduced by almost 20–30% with the coexistence of ${{\text{SO}}_4}^{2?}$, ${{\text{NO}}_3}^{?}$ and humic acid (HA).     

新型铁铜铝三元复合氧化物除磷性能与机制研究

采用共沉淀法制备了一种新型铁铜铝三元复合氧化物吸附剂,系统研究了其对磷的吸附行为,并对吸附磷前后的吸附剂进行了表征.吸附实验结果表明,铁铜铝三元复合氧化物对磷具有优异的吸附去除效能,Freundlich吸附等温线模型能更好地拟合其对磷的吸附,最大吸附量为62.6 mg·g-1(pH=7.0),显著高于多数文献报道的磷吸附剂;吸附速率较快,吸附动力学更符合Elovich模型;溶液pH对磷吸附有一定影响,随着pH的升高,磷吸附量降低,离子强度则影响不大;共存阴离子对磷吸附具有抑制作用,影响的大小顺序为SiO_3~(2-)SO_4~(2-)CO_3~(2-)Cl~-,而共存阳离子Ca2+和Mg2+则对磷吸附略有促进作用.Zeta电位、红外谱图(FTIR)和X射线光电子能谱(XPS)表征分析表明,磷在铁铜铝三元复合氧化物表面发生了特性吸附,磷酸根主要通过取代复合氧化物表面的羟基形成内表面络合物而被吸附去除.溶出实验结果表明,当pH在5.0~8.5范围内,Fe~(3+)、Cu~(2+)、Al~(3+)的溶出量均较低.由此可知,铁铜铝三元复合氧化物是一种具有良好应用前景的除磷吸附剂.     

Removal of fluoride from water using titanium-based adsorbents

Three adsorbents including TiO₂, Ti-Ce, and Ti-La hybrid oxides were prepared to remove fluoride from aqueous solution. The Ti-Ce and Ti-La hybrid adsorbents obtained by the hydrolysis-precipitation method had much higher sorption capacity for fluoride than the TiO₂ adsorbent prepared through hydrolysis. Rare earth (Ce and La) oxides and TiO₂ exhibited a synergistic effect in the hybrid adsorbents for fluoride sorption. The sorption equilibrium of fluoride on the three adsorbents was achieved within 4 h, and the pseudo-second-order model described the sorption kinetics well. The sorption isotherms fitted the Langmuir model well, and the adsorption capacities of fluoride on the Ti-Ce and Ti-La adsorbents were about 9.6 and 15.1 mg·g⁻¹, respectively, at the equilibrium fluoride concentration of 1.0 mg·L⁻¹, much higher than the 1.7 mg·g⁻¹ on the TiO₂. The sorption capacities of fluoride on the three adsorbents decreased significantly when the solution pH increased from 3 to 9.5. The electrostatic interaction played an important role in fluoride removal by the three adsorbents, and Fourier transform infrared (FTIR) analysis indicated that the hydroxyl groups on the adsorbent surface were involved in fluoride adsorption.     

Pb（II） biosorption using chitosan and chitosan derivatives beads： Equilibrium, ion exchange and mechanism studies

The study examined the adsorption of Pb(II) ions from aqueous solution onto chitosan, chitosan-GLA and chitosan-alginate beads. Several important parameters influencing the adsorption of Pb(II) ions such as initial pH, adsorbent dosage and di erent initial concentration of Pb(II) ions were evaluated. The mechanism involved during the adsorption process was explored based on ion exchange study and using spectroscopic techniques. The adsorption capacities obtained based on non–linear Langmuir isotherm for chitosan, chitosan-GLA and chitosan-alginate beads in single metal system were 34.98, 14.24 and 60.27 mg/g, respectively. However, the adsorption capacity of Pb(II) ions were reduced in the binary metal system due to the competitive adsorption between Pb(II) and Cu(II) ions. Based on the ion exchange study, the release of Ca2+, Mg2+, K+ and Na+ ions played an important role in the adsorption of Pb(II) ions by all three adsorbents but only at lower concentrations of Pb(II) ions. Infrared spectra showed that the binding between Pb(II) ions and the adsorbents involved mostly the nitrogen and oxygen atoms. All three adsorbents showed satisfactory adsorption capacities and can be considered as an e cient adsorbent for the removal of Pb(II) ions from aqueous solutions.     

Mesoporous carbon adsorbents from melamine–formaldehyde resin using nanocasting technique for CO2 adsorption

Mesoporous carbon adsorbents, having high nitrogen content, were synthesized via nanocasting technique with melamine–formaldehyde resin as precursor and mesoporous silica as template. A series of adsorbents were prepared by varying the carbonization temperature from 400 to 700°C. Adsorbents were characterized thoroughly by nitrogen sorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), elemental (CHN) analysis, Fourier transform infrared (FTIR) spectroscopy and Boehm titration. Carbonization temperature controlled the properties of the synthesized adsorbents ranging from surface area to their nitrogen content, which play major role in their application as adsorbents for CO₂ capture. The nanostructure of these materials was confirmed by XRD and TEM. Their nitrogen content decreased with an increase in carbonization temperature while other properties like surface area, pore volume, thermal stability and surface basicity increased with the carbonization temperature. These materials were evaluated for CO₂ adsorption by fixed-bed column adsorption experiments. Adsorbent synthesized at 700°C was found to have the highest surface area and surface basicity along with maximum CO₂ adsorption capacity among the synthesized adsorbents. Breakthrough time and CO₂ equilibrium adsorption capacity were investigated from the breakthrough curves and were found to decrease with increase in adsorption temperature. Adsorption process for carbon adsorbent–CO₂ system was found to be reversible with stable adsorption capacity over four consecutive adsorption–desorption cycles. From three isotherm models used to analyze the equilibrium data, Temkin isotherm model presented a nearly perfect fit implying the heterogeneous adsorbent surface.     

Mesoporous carbon adsorbents from melamine-formaldehyde resin using nanocasting technique for CO2 adsorption

Mesoporous carbon adsorbents, having high nitrogen content, were synthesized via nanocasting technique with melamine–formaldehyde resin as precursor and mesoporous silica as template. A series of adsorbents were prepared by varying the carbonization temperature from 400 to 700°C. Adsorbents were characterized thoroughly by nitrogen sorption, X-ray diffraction(XRD), scanning electron microscopy(SEM), transmission electron microscopy(TEM), thermogravimetric analysis(TGA), elemental(CHN) analysis, Fourier transform infrared(FTIR) spectroscopy and Boehm titration. Carbonization temperature controlled the properties of the synthesized adsorbents ranging from surface area to their nitrogen content, which play major role in their application as adsorbents for CO_2 capture.The nanostructure of these materials was confirmed by XRD and TEM. Their nitrogen content decreased with an increase in carbonization temperature while other properties like surface area, pore volume, thermal stability and surface basicity increased with the carbonization temperature. These materials were evaluated for CO_2 adsorption by fixed-bed column adsorption experiments. Adsorbent synthesized at 700°C was found to have the highest surface area and surface basicity along with maximum CO_2 adsorption capacity among the synthesized adsorbents. Breakthrough time and CO_2 equilibrium adsorption capacity were investigated from the breakthrough curves and were found to decrease with increase in adsorption temperature. Adsorption process for carbon adsorbent–CO_2 system was found to be reversible with stable adsorption capacity over four consecutive adsorption–desorption cycles. From three isotherm models used to analyze the equilibrium data, Temkin isotherm model presented a nearly perfect fit implying the heterogeneous adsorbent surface.     

PAAm/HACC半互穿网络水凝胶的制备及其对水中腐殖酸的吸附性能

采用原位聚合热合成法成功制备了聚丙烯酰胺-壳聚糖季铵盐半互穿网络水凝胶(PAAm/HACC semi-IPN)新型吸附剂(s-IPN 1.5)和(s-IPN 3),并用于吸附水体中的腐殖酸.利用扫描电镜(SEM)、红外光谱(FT-IR)、X射线衍射光谱(XRD)等方法对吸附剂的结构进行表征.考察了溶液pH、离子强度、接触时间、腐殖酸初始浓度及温度等对吸附剂吸附腐殖酸的影响.结果表明s-IPN 3的吸附效果要优于s-IPN 1.5.吸附剂对腐殖酸的吸附量随着pH的增大而减小,随温度的升高而增大,且一定的离子强度有助于吸附剂对腐殖酸的吸附.吸附过程能较好地用准二级动力学模型及Sips等温模型进行拟合.吸附剂在pH 7.0,离子强度0.01 mol·L-1,温度为298 K条件下的最大吸附量可高达238.08 mg·g-1,吸附效果显著,能有效去除水体中的腐殖酸.     

海藻酸锆/聚N-异丙基丙烯酰胺半互穿网络凝胶球的除磷性能

利用离子交联和自由基聚合反应制备了一种海藻酸锆/聚(N-异丙基丙烯酰胺)半互穿网络凝胶球(ZA/PNIPAM),用于吸附水中的磷酸盐.考察了溶液初始pH、吸附剂投加量、初始磷酸盐浓度和共存阴离子等因素对凝胶球吸附性能的影响.结果表明:ZA/PNIPAM在pH=2时可获得较大的吸附能力;随着投加量的减少、初始磷酸盐浓度的升高,凝胶球的吸附性能逐渐增大;SO_4~(2-)对吸附性能影响较Cl~-和NO_3~-明显.准二级动力学模型和颗粒内部扩散模型可以较好地拟合动力学吸附数据,表明表面吸附和颗粒内部扩散是吸附速率的主要控制步骤.吸附等温线数据可以较好地被Freundlich模型描述,表明吸附过程为非均匀多分子层吸附.FTIR、XPS、零电荷点(pH_(pzc))的结果以及相关吸附数据揭示凝胶球吸附磷酸盐的机制为静电吸附(物理吸附)以及配位交换(化学吸附)的共同作用.经过4次循环再生后,ZA/PNIPAM吸附性能保持稳定,具有良好的重复使用性.     

改性壳聚糖季铵盐的研制及其对高氯酸盐的吸附研究

通过将壳聚糖季铵盐改性以实现固定化,并用于水体中ClO 4-的吸附去除,研究了改性过程相关工艺参数对产物吸附能力的影响,考察了产物的吸附和再生性能.结果表明,戊二醛的交联性能优于甲醛和环氧氯丙烷的交联性能,戊二醛的最佳投加量为6.82%,最佳的反应温度为45℃,pH值在3～12之间交联反应均能很好地进行,从而实现壳聚糖...     

Capture of carbon dioxide from flue gas on TEPA-grafted metal-organic framework Mg2(dobdc)

Carbon dioxide （CO2） adsorption on a standard metal-organic framework Mg2（dobdc） （Mg/DOBDC or Mg-MOF-74） and a tetraethylenepentamine （TEPA） modified Mgz（dobdc） （TEPA-Mg/DOBDC） were investigated and compared. The structural information, surface chemistry and thermal behavior of the adsorbent samples were characterized by X-ray powder diffraction （XRD）, infrared spectroscopy （IR）, thermogravimetric analysis （TGA） and nitrogen adsorption-desorption isotherm analysis. CO2 adsorption capacity was measured by dynamic adsorption experiments with N2-CO2 mixed gases at 60℃. Results showed that the CO2 adsorption capacity of Mg/DOBDC was significantly improved after amine modification, with an increase from 2.67 to 6.06 mmol CO2/g adsorbent. Moreover, CO2 adsorption on the TEPA-Mg/DOBDC adsorbent was promoted by water vapor, and the adsorption capacity was enhanced to 8.31 mmol CO2/g absorbent. The adsorption capacity of the TEPA-Mg/DOBDC adsorbent dropped only 3% after 5 consecutive adsorption]desorption cycles. Therefore, this kind of adsorbent can be considered as a promising material for the capture of CO2 from flue gas.     

Highly efficient and selective removal of low-concentration antibiotics from aqueous solution by regenerable Mg(OH)2

The prevalent presence of fluoroquinolone antibiotics in aquatic environments has attracted considerable attention because of their harmful effects on humans and the ecological environment. Magnesium hydroxide nanocrystals were found to act as a simple and effective adsorbent to remove low-concentration ciprofloxacin (CIP) in aqueous solution. The as-prepared Mg(OH)₂ nanocrystals exhibited excellent CIP adsorption performance and high selectivity toward CIP molecules compared with other antibiotics or aromatics, e.g., norfloxacin (NOR) and eosin B (EB). The adsorbent showed pH-dependent adsorption, indicating that the adsorption process is probably dominated by an electrostatic interaction mechanism. In addition, structural analysis of the adsorbent indicated that coordination and hydrogen bonding between CIP and Mg(OH)₂ nanocrystal might also be involved in the adsorption process. Moreover, the adsorbent could be easily recovered by pyrolysis and hydration without significant reduction of adsorption capacity. The superior adsorption behavior of Mg(OH)₂ nanocrystal indicates that it may serve as a potential adsorbent material candidate for the selective removal of CIP from aquatic environments.     

氢氧化镧改性介孔稻壳生物炭除磷性能

通过共沉淀法将氢氧化镧固定在高介孔率的稻壳生物炭上,重点研究了生物炭孔结构、溶液pH和共存物质对氢氧化镧改性介孔稻壳生物炭吸附磷酸盐的影响.结果表明,镧负载量与生物炭介孔率呈正相关,生物炭介孔率越高,对磷酸盐的吸附速率越快,镧浸出量越低.吸附过程符合伪二级动力学模型,且受颗粒内扩散控制.Langmuir模型能够较好地描述氢氧化镧改性介孔稻壳生物炭对磷酸盐的吸附过程,理论最大吸附量分别为41.22、43.26和45.62 mg·g^-1,镧利用率较高,P/La量比均大于1.5.此外,氢氧化镧改性介孔稻壳生物炭能在pH 3~9的范围内有效吸附磷酸盐.共存物质影响实验表明,氢氧化镧改性介孔稻壳生物炭对磷酸盐表现出良好的选择吸附性,共存Ca²⁺会强化其对磷酸盐的吸附,而共存Mg²⁺则会抑制吸附过程.     

氧化镁基生物质炭高效去除水体中磷的特性

利用花生壳为前驱体,在高温限氧条件下,将氧化镁(MgO)负载于生物质炭(BC)表面制备出氧化镁基生物质炭(MgOBC)复合材料.系统研究了MgO-BC对水体中P的吸附特性,并探讨了溶液pH值、接触时间、竞争离子等因素对P的吸附效果的影响.结果表明,P的最佳吸附初始pH为7~9,过酸过碱的环境均不利于P的吸附;P的吸附过程可在540 min内达到平衡,且动力学曲线较好地符合伪一级和伪二级动力学模型,拟合系数可达97.3%和99.0%;当Cl~-、HCO_3~-、NO_3~-等共存离子的量浓度达到P的10倍时,MgO-BC对P仍具有较强的吸附能力;P的吸附过程较好地符合Langmuir等温模型,拟合系数达99%,理论最大吸附容量为138.07 mg·g~(-1),远高于其它未经改性或改性的生物质炭和几种典型P吸附剂的吸附容量.此外,吸附P后的复合材料可作为肥料施入土壤,可有效实现P的再利用.综上所述,该MgO-BC复合材料在净化实际P污染水体中有着广阔的应用前景.     

Asenic removal from groundwater using granular chitosan-titanium adsorbent

Arsenic(As) contamination poses an urgent environmental risk, and its removal from groundwater remains a challenge due to the lack of efficient adsorbents. Herein, a novel granular chitosan-titanium(CS-Ti) adsorbent was fabricated by the sol-gel method. Batch experiments show that As(V) adsorption on CS-Ti followed the pseudo-second-order kinetic model, and the adsorption isotherm conformed to the Freundlich model with the correlation coefficient of 0.99. In situ FTIR spectra revealed that the C...     

不同锆负载量锆改性膨润土对水中磷酸盐吸附作用的对比

通过实验对比考察了不同锆负载量的锆改性膨润土对水中磷酸盐的吸附作用.结果表明,锆改性膨润土对水中磷酸盐的吸附动力学过程符合准二级动力学模型,整个过程可以分为快速吸附阶段、缓慢吸附阶段和平衡吸附阶段,其中缓慢吸附阶段的吸附速率受膜扩散和颗粒内扩散所控制.锆改性膨润土对水中磷酸盐的吸附等温实验数据可以采用Langmuir、Freundlich、Sips和Dubinin-Radushkevich等温吸附模型进行拟合.实验条件下,磷酸盐吸附性能随pH增加而降低.溶液共存的Na~+、K~+和Ca~(2+)促进了锆改性膨润土对磷酸盐的吸附,并且Ca~(2+)的促进作用远远大于Na~+和K+,而溶液共存的HCO-3和SO2-4一定程度上抑制了锆改性膨润土对磷酸盐的吸附.锆改性膨润土吸附水中磷酸盐的主要机制为配位体交换并形成内层磷酸盐配合物.锆改性膨润土对水中磷酸盐的吸附能力随着锆负载量的增加而增加,而锆改性膨润土中单位质量ZrO_2对水中磷酸盐的吸附量则随着锆负载量的增加而降低.当ZrO_2负载量由3.61%增加到13.15%时锆改性膨润土的最大单层单位吸附量(以P计)显著地由3.83 mg·g~(-1)增加到9.03 mg·g~(-1),而继续增加ZrO_2负载量至19.63%时锆改性膨润土的最大单层单位吸附量则缓慢地提高到9.66 mg·g~(-1)(以P计).当ZrO_2负载量由3.61%逐渐增加到19.63%时,锆改性膨润土中单位质量ZrO_2的磷酸盐最大吸附量[m(P)/m(ZrO_2)]由106 mg·g~(-1)逐渐下降到49.2 mg·g~(-1).综合考虑吸附剂的经济成本和吸附容量,ZrO_2负载量为13.15%锆改性膨润土更为适合作为吸附剂去除水中磷酸盐.     

Synthesis of a novel illite@carbon nanocomposite adsorbent for removal of Cr(VI) from wastewater

A novel illite@carbon (I@C) nanocomposite adsorbent has been synthesized via a facile hydrothermal carbonization process (HTC) using glucose as carbonaceous source and illite as the carrier. The morphology, microstructure and surface properties of the prepared nanocomposite adsorbent were analyzed by FESEM, TGA, XRD, FT-IR and Zeta potential measurements. Batch experiments were carried out on the adsorption of Cr(VI) to determine the adsorption properties of the composite. The adsorption of Cr(VI) onto the I@C nanocomposite was well described by the pseudo-second-order kinetic model and Langmuir isotherm. Compared with the illite and carbon material (SC) separately, the prepared I@C nanocomposite adsorbent exhibited enhanced adsorption performance for Cr(VI) with a maximum adsorption capacity of 149.25 mg/g, which was higher than that of most reported adsorbents. In addition, the adsorption process was spontaneous and endothermic based on the adsorption thermodynamics study. The adsorption of Cr(VI) by I@C was highly pH-dependent and the optimum adsorption occurred at pH 2.0. The Zeta potential analysis results indicated that the electrostatic interactions between anionic Cr(VI) and the positively charged surface of the adsorbent might be critical to the adsorption mechanism. This study demonstrated that the I@C nanocomposite should be a promising candidate for a low-cost, environmental friendly and highly efficient adsorbent for the removal of toxic Cr(VI) from wastewater.     

不同沉淀pH值条件下制备的水合氧化锆对水中磷酸盐的吸附作用

研究了沉淀pH值分别为4.8、8.0和10.6条件下制备的水合氧化锆对水中磷酸盐的吸附作用,结果表明,共存的Na~+仅仅略微促进了沉淀pH值为4.8和8.0时所得水合氧化锆对水中磷酸盐的吸附,却明显促进了沉淀pH值为10.6时所得水合氧化锆对磷酸盐的吸附.共存的Ca~(2+)仅仅略微促进了沉淀pH值为4.8时水合氧化锆对磷酸盐的吸附,却极大地促进了沉淀pH值为8.0和10.6时水合氧化锆对磷酸盐的吸附.共存的HCO_3~-和SO_4~(2-)抑制了水合氧化锆对磷酸盐的吸附,且它们对沉淀pH值为4.8时水合氧化锆吸磷的抑制作用明显大于对沉淀pH值为8.0和10.6时水合氧化锆的抑制作用.不同沉淀pH值条件下制备的水合氧化锆对水中磷酸盐的吸附能力均随着溶液pH值的增加而降低.不同沉淀pH值条件下所得水合氧化锆对水中磷酸盐的吸附平衡数据可以采用Langmuir、Freundlich和Dubinin-Redushckevich(D-R)等温吸附模型加以描述.存在Na+而不存在Ca~(2+)情况下,3种不同沉淀pH值条件下所得水合氧化锆对中性溶液中磷酸盐的最大单层吸附容量差别不大;存在Ca~(2+)情况下,沉淀pH值为8.0和10.6时所得水合氧化锆对中性溶液中磷酸盐的最大单层吸附容量远远高于沉淀pH值为4.8时制备的水合氧化锆.沉淀pH值为4.8和8.0时所得水合氧化锆的吸磷机制主要是表面氯和羟基基团与磷酸盐之间的配位体交换作用,而沉淀pH值为10.6时所得水合氧化锆的吸磷机制主要是表面羟基基团与磷酸盐之间的配位体交换作用.以上研究结果显示,与沉淀pH值为4.8时制备的水合氧化锆相比,沉淀pH值为8.0和10.6时制备的水合氧化锆更加适合作为吸附剂去除废水中的磷酸盐.