Pb(Ⅱ) biosorption using chitosan and chitosan derivatives beads: Equilibrium,ion exchange and mechanism studies

The study examined the adsorption of Pb(II) ions from aqueous solution onto chitosan, chitosan-GLA and chitosan-alginate beads. Several important parameters influencing the adsorption of Pb(II) ions such as initial pH, adsorbent dosage and different initial concentration of Pb(II) ions were evaluated. The mechanism involved during the adsorption process was explored based on ion exchange study and using spectroscopic techniques. The adsorption capacities obtained based on non-linear Langmuir isotherm for ch...     

Removal of heavy metals from aqueous solution by sawdust adsorption

The adsorption of lead, cadmium and nicel from aqueous solution by sawdust of walnut was investigated. The effect of contact time, initial metal ion concentration and temperature on metal ions removal has been studied. The equilibrium time was found to be of the order of 60 min. Kinetics fit pseudo first-order, second-order and intraparticle diffusion models, hence adsorption rate constants were calculated. The adsorption data of metal ions at temperatures of 25, 45 and 60~C have been described by the Freundlich and Langmuir isotherm models. The thermodynamic parameters such as energy, entropy and enthalpy changes for the adsorption of heavy metal ions have also been computed and discussed. Ion exchange is probably one of the major adsorption mechanisms for binding divalent metal ions to the walnut sawdust. The selectivity order of the adsorbent is Pb（I1）~Cd（II）〉Ni（I1）. From these results, it can be concluded that the sawdust of walnut could be a good adsorbent for the metal ions from aqueous solutions.     

Preparation and properties of chitosan–metal complex: Some factors influencing the adsorption capacity for dyes in aqueous solution

Chitosan–metal complexes have been widely studied in wastewater treatment, but there are still various factors in complex preparation which are collectively responsible for improving the adsorption capacity need to be further studied. Thus, this study investigates the factors affecting the adsorption ability of chitosan–metal complex adsorbents, including various kinds of metal centers, different metal salts and crosslinking degree. The results show that the chitosan–Fe( Ⅲ) complex prepared by sulfate salts exhibited the best adsorption efficiency(100%) for various dyes in very short time duration(10 min), and its maximum adsorption capacity achieved 349.22 mg/g. The anion of the metal salt which was used in preparation played an important role to enhance the adsorption ability of chitosan–metal complex. SO_4~(2-) ions not only had the effect of crosslinking through electrostatic interaction with amine group of chitosan polymer, but also could facilitate the chelation of metal ions with chitosan polymer during the synthesis process.Additionally, the p H sensitivity and the sensitivity of ionic environment for chitosan–metal complex were analyzed. We hope that these factors affecting the adsorption of the chitosan–metal complex can help not only in optimizing its use but also in designing new chitosan–metal based complexes.     

Simultaneous adsorption of lead and cadmium on MnO2-loaded resin

MnO2-loaded D301 weak basic anion exchange resin has been used as adsorbent to simultaneously remove lead and cadmium ions from aqueous solution. The e ects of adsorbent dosage, solution pH and the coexistent ions on the adsorption were investigated. Experimental results showed that with the adsorbent dosage more than 0.6 g/L, both Pb2+ and Cd2+ were simultaneously removed at pH range 5–6. Except for HPO4 2??, the high concentration coexistent ions such as Na+, K+, Cl??, NO3??, SO4 2?? and HCO3??, showed no significant e ect on the removal e ciency of both Pb2+ and Cd2+ under the experimental conditions. The coexistence of Mg2+, Ca2+ caused the reduction of Cd2+ removal, but not for Pb2+. The adsorption equilibrium for Pb2+ and Cd2+ could be excellently described by the Langmuir isotherm model with R2 > 0.99. The maximum adsorption capacity was calculated as 80.64 mg/g for Pb2+ and 21.45 mg/g for Cd2+. The adsorption processes followed the pseudo first-order kinetics model. MnO2-loaded D301 resin has been shown to have a potential to be used as an e ective adsorbent for simultaneous removal of lead and cadmium ions from aqueous solution.     

Selective adsorption of silver ions from aqueous solution using polystyrene-supported trimercaptotriazine resin

Trimercaptotriazine-functionalized polystyrene chelating resin was prepared and employed for the adsorption of Ag(I) from aqueous solution. The adsorbent was characterized according to the following techniques: Fourier transform infrared spectroscopy, elemental analysis, scanning electron microscopy and the Brunauer-Emmet-Teller method. The effects of initial Ag(I) concentration, contact time, solution pH and coexisting ions on the adsorption capacity of Ag(I) were systematically investigated. The maximum adsorption capacity of Ag(I) was up to 187.1 mg/g resin at pH 0.0 and room temperature. The kinetic experiments indicated that the adsorption rate of Ag(I) onto the chelating resin was quite fast in the first 60 min and reached adsorption equilibrium after 360 min. The adsorption process can be well described by the pseudo second-order kinetic model and the equilibrium adsorption isotherm was closely fitted by the Langmuir model. Moreover, the chelating resin could selectively adsorb more Ag(I) ions than other heavy metal ions including: Cu(II), Zn(II), Ni(II), Pb(II) and Cr(III) during competitive adsorption in the binary metal species systems, which indicated that it was a highly selective adsorbent of Ag(I) from aqueous solution.     

Adsorption of heavy metal ions from aqueous solution by carboxylated cellulose nanocrystals

A novel nanoadsorbent for the removal of heavy metal ions is reported.Cotton was first hydrolyzed to obtain cellulose nanocrystals(CNCs).CNCs were then chemically modified with succinic anhydride to obtain SCNCs.The sodic nanoadsorbent(NaSCNCs) was further prepared by treatment of SCNCs with saturated NaHCO 3 aqueous solution.Batch experiments were carried out with SCNCs and NaSCNCs for the removal of Pb 2+ and Cd 2+.The effects of contact time,pH,initial adsorption concentration,coexisting ions and the regeneration performance were investigated.Kinetic studies showed that the adsorption equilibrium time of Pb 2+ and Cd 2+ was reached within 150 min on SCNCs and 5 min on NaSCNCs.The adsorption capacities of Pb 2+ and Cd 2+ on SCNCs and NaSCNCs increased with increasing pH.The adsorption isotherm was well fitted by the Langmuir model.The maximum adsorption capacities of SCNCs and NaSCNCs for Pb 2+ and Cd 2+ were 367.6 mg/g,259.7 mg/g and 465.1 mg/g,344.8 mg/g,respectively.SCNCs and NaSCNCs showed high selectivity and interference resistance from coexisting ions for the adsorption of Pb 2+.NaSCNCs could be efficiently regenerated with a mild saturated NaCl solution with no loss of capacity after two recycles.The adsorption mechanisms of SCNCs and NaSCNCs were discussed.     

Sequestration of toxic Pb（II） ions by chemically treated rubber （Hevea brasiliensis ） leaf powder

Rubber leaf powder (an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(II) ions from aqueous solution was evaluated. The interactions between Pb(II) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) coupled with X-ray energy dispersive spectroscopy (EDX). The effects of several important parameters which can affect adsorption capacity such as pH, adsorbent dosage, initial lead concentration and contact time were studied. The optimum pH range for lead adsorption was 4–5. Even at very low adsorbent dosage of 0.02 g, almost 100% of Pb(II) ions (23 mg/L) could be removed. The adsorption capacity was also dependent on lead concentration and contact time, and relatively a short period of time (60–90 min) was required to reach equilibrium. The equilibrium data were analyzed with Langmuir, Freundlich and Dubinin-Radushkevich isotherms. Based on Langmuir model, the maximum adsorption capacity of lead was 95.3 mg/g. Three kinetic models including pseudo first-order, pseudo second-order and Boyd were used to analyze the lead adsorption process, and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.     

Shellac-coated iron oxide nanoparticles for removal of cadmium(II) ions from aqueous solution

This study describes a new effective adsorbent for cadmium removal from aqueous solution synthesized by coating a shellac layer, a natural biodegradable and renewable resin with abundant hydroxyl and carboxylic groups, on the surface of iron oxide magnetic nanoparticles. Transmission Electron Microscopy (TEM) imaging showed shellac-coated magnetic nanoparticle (SCMN) adsorbents had a core-shell structure with a core of 20 nm and shell of 5 nm. Fourier Transform Infrared Spectroscopic analysis suggested the occurrence of reaction between carboxyl groups on the SCMN adsorbent surface and cadmium ions in aqueous solution. Kinetic data were well described by pseudo second-order model and adsorption isotherms were fitted with both Langmuir and Freundlich models with maximum adsorption capacity of 18.80 mg/g. SCMN adsorbents provided a favorable adsorption capacity under high salinity conditions, and cadmium could easily be desorbed using mild organic acid solutions at low concentration.     

Simultaneous removal of Congo red and cadmium(II) from aqueous solutions using graphene oxide–silica composite as a multifunctional adsorbent

Graphene oxide is a very high capacity adsorbent due to its functional groups and π?π interactions with other compounds. Adsorption capacity of graphene oxide, however, can be further enhanced by having synergistic effects through the use of mixed-matrix composite. In this study, silica-decorated graphene oxide (SGO) was used as a high-efficiency adsorbent to remove Congo red (CR) and Cadmium (II) from aqueous solutions. The effects of solution initial concentration (20 to 120 mg/l), solution pH (pH 2 to 7), adsorption duration (0 to 140 min) and temperature (298 to 323 K) were measured in order to optimize the adsorption conditions using the SGO adsorbent. Morphological analysis indicated that the silica nanoparticles could be dispersed uniformly on the graphene oxide surfaces. The maximum capacities of adsorbent for effective removal of Cd (II) and CR were 43.45 and 333.33 mg/g based on Freundlich and Langmuir isotherms, respectively. Langmuir and Freundlich isotherms displayed the highest values of Q_max for CR and Cd (II) adsorption in this study, which indicated monolayer adsorption of CR and multilayer adsorption of Cd (II) onto the SGO, respectively. Thermodynamic study showed that the enthalpy (ΔH) and Gibbs free energy(ΔG) values of the adsorption process for both pollutants were negative, suggesting that the process was spontaneous and exothermic in nature. This study showed active sites of SGO (π-π, hydroxyl, carboxyl, ketone, silane-based functional groups) contributed to an enormous enhancement in simultaneous removal of CR and Cd (II) from an aqueous solution, Therefore, SGO can be considered as a promising adsorbent for future water pollution control and removal of hazardous materials from aqueous solutions.     

Comparative equilibrium studies of sorption of Pb(II) ions by sodium and calcium alginate

The absorption of Pb(II) ions from aqueous solution by di erent alginate compounds was studied in a batch sorption system. Water soluble sodium alginate and insoluble calcium alginate beads were investigated. The lead-binding capacity of both alginate compounds was highest within the pH range 6–8. The binding capacities and rates of Pb(II) ions by alginate compounds were evaluated. The Langmuir, Freundlich, and Bruneaur, Emmet and Teller (BET) sorption models were applied to describe the isotherms and isotherm constants. Sorption isothermal data could be well interpreted by the Langmuir model. The results obtained through the study suggest that alginate compounds are favorable sorbents. The largest amount of Pb(II) ions were bound by sodium alginate although the di erence between two compounds was slight. Therefore, alginate substances may be considered as an alternative for sorption and removal of Pb(II) ions from wastewaters.     

Pb(Ⅱ) biosorption using chitosan and chitosan derivatives beads: Equilibrium, ion exchange and mechamsm studies

The study examined the adsorption of Pb(Ⅱ) ions from aqueous solution onto chitosan, chitosan-GLA and chitosan-alginate beads.Several important parameters influencing the adsorption of Pb(Ⅱ) ions such as initial pH, adsorbent dosage and different initial concentration of Pb(Ⅱ) ions were evaluated. The mechanism involved during the adsorption process was explored based on ion exchange study and using spectroscopic techniques. The adsorption capacities obtained based on non-linear Langmuir isotherm for chitosan, chitosan-GLA and chitosan-alginate beads in single metal system were 34.98, 14.24 and 60.27 mg/g, respectively. However,the adsorption capacity of Pb(Ⅱ) ions were reduced in the binary metal system due to the competitive adsorption between Pb(Ⅱ) and Cu(Ⅱ) ions. Based on the ion exchange study, the release of Ca~(2+), Mg~(2+), K~+ and Na~+ ions played an important role in the adsorption of Pb(Ⅱ) ions by all three adsorbents but only at lower concentrations of Pb(Ⅱ) ions. Infrared spectra showed that the binding between Pb(Ⅱ) ions and the adsorbents involved mostly the nitrogen and oxygen atoms. All three adsorbents showed satisfactory adsorption capacities and can be considered as an efficient adsorbent for the removal of Pb(Ⅱ) ions from aqueous solutions.     

High phosphate removal using La(OH)3 loaded chitosan based composites and mechanistic study

Our present study was to prepare a biomass-supported adsorbents with high adsorptive capacity and high selectivity to prevent the accelerated eutrophication in water body. To this end, different metal hydroxide (La, Zr and Fe) first was successfully loaded on chitosan microspheres. Then the quaternary ammonium group with different content was introduced into the adsorbent by polymerization. By comparison of adsorption properties, chitosan-La(OH)₃-quaternary ammonium-20% (CS-La-N-20%) has strong adsorption to phosphate (160 mg/g) by immobilizing nano-sized La(OH)₃ within a quaternary-aminated chitosan and it maintain high adsorption in the presence of salt ions. The pH results indicated that the CS-La-N-20% would effectively sequestrate phosphate over a wide pH range between 3 and 7 without significant La³⁺ leaching. What's more, adsorption capacity on the introduce of positively charged quanternary-aminated groups was significantly higher than that of the unmodified adsorbents at alkaline conditions. The column adsorption capacity reached 1300 bed volumes (BV) when phosphate concentration decreased until 0.5 mg/L at 6 BV/hr. The column adsorption/desorption reveals that no significant capacity loss is observed, indicating excellent stability and repeated use property. Characterizations revealed that phosphate adsorption on CS-La-N-20% through ligand exchange (impregnated nano-La(OH)₃) and electrostatic attraction (positively charged quanternary-aminated groups). All the results suggested that CS-La-N-20% can serve as a promising adsorbent for preferable phosphate removal in realistic application.     

Chitosan and chemically modified chitosan beads for acid dyes sorption

The capabilities of chitosan and chitosan-EGDE (ethylene glycol diglycidyl ether) beads for removing Acid Red 37 (AR 37) and Acid Blue 25 (AB 25) from aqueous solution were examined. Chitosan beads were cross-linked with EGDE to enhance its chemical resistance and mechanical strength. Experiments were performed as a function of pH, agitation period and concentration of AR 37 and AB 25. It was shown that the adsorption capacities of chitosan were comparatively higher than chitosan-EGDE for both acid dyes. This is mainly because cross-linking using EGDE reduces the major adsorption sites -NH3+ on chitosan. Langmuir isotherm model showed best conformity compared to Freundlich and BET. The kinetic experimental data agreed very well to the pseudo second-order kinetic model. The desorption study revealed that after three cycles of adsorption and desorption by NaOH and HCl, both adsorbents retained their promising adsorption abilities. FT-IR analysis proved that the adsorption of acid dyes onto chitosan-based adsorbents was a physical adsorption. Results also showed that chitosan and chitosan-EGDE beads were favourable adsorbers and could be employed as low-cost alternatives for the removal of acid dyes in wastewater treatment.     

Removal of heavy metal ions from aqueous solution using red loess as an adsorbent

The adsorption behaviors of heavy metals onto novel low-cost adsorbent, red loess, were investigated. Red loess was characterized by X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectra. The results indicated that red loess mainly consisted of silicate, ferric and aluminum oxides. Solution pH, adsorbent dosage, initial metal concentration, contact time and temperature significantly influenced the efficiency of heavy metals removal. The adsorption reached equilibrium at 4 hr, and the experimental equilibrium data were fitted to Langmuir monolayer adsorption model. The adsorption of Cu(II) and Zn(II) onto red loess was endothermic, while the adsorption of Pb(II) was exothermic. The maximum adsorption capacities of red loess for Pb(II), Cu(II) and Zn(II) were estimated to be 113.6, 34.2 and 17.5 mg/g, respectively at 25°C and pH 6. The maximum removal efficiencies were 100% for Pb(II) at pH 7, 100% for Cu(II) at pH 8, and 80% for Zn(II) at pH 8. The used adsorbents were readily regenerated using dilute HC1 solution, indicating that red loess has a high reusability. All the above results demonstrated that red loess could be used as a possible alternative low-cost adsorbent for the removal of heavy metals from aqueous solution.     

不同类型酸修饰-磁化海泡石对水体Cd(II)的吸附研究

采用无机或有机酸修饰-磁化的方法研制海泡石吸附材料H-Sep(盐酸修饰)、N-Sep(硝酸修饰)、P-Sep(磷酸修饰)和A-Sep(醋酸修饰),并借助SEM、TEM、EDS、BET、FT-IR、VSM及XPS等手段表征分析改性前后海泡石的结构特征.同时,在不同投加量、pH、温度和溶液浓度等因素条件下,考察了酸修饰-磁化海泡石对水体Cd(II)吸附效果的影响.结果表明,改性材料取得最佳吸附效果时的投加量为5g·L^-1,pH为6.5,拟合结果更符合准二级动力学方程和Langmuir等温方程.其中,P-Sep的吸附效果最好,其最大理论吸附量为52.6 mg·g^-1.VSM结果表明,H-Sep、N-Sep和A-Sep是磁化分离效果较好的材料,而P-Sep的磁化分离效果不佳.此外,Na⁺、Cl^-等阴阳离子对酸修饰-磁改性海泡石吸附性能没有太大影响,而重金属离子如Pb(II)、Zn(II)会对其吸附过程产生抑制作用.XPS吸附机理分析表明,酸修饰-磁化改性将新的功能基团引入海泡石结构,极大地提升了吸附性能.     

PAAm/HACC半互穿网络水凝胶的制备及其对水中腐殖酸的吸附性能

采用原位聚合热合成法成功制备了聚丙烯酰胺-壳聚糖季铵盐半互穿网络水凝胶(PAAm/HACC semi-IPN)新型吸附剂(s-IPN 1.5)和(s-IPN 3),并用于吸附水体中的腐殖酸.利用扫描电镜(SEM)、红外光谱(FT-IR)、X射线衍射光谱(XRD)等方法对吸附剂的结构进行表征.考察了溶液pH、离子强度、接触时间、腐殖酸初始浓度及温度等对吸附剂吸附腐殖酸的影响.结果表明s-IPN 3的吸附效果要优于s-IPN 1.5.吸附剂对腐殖酸的吸附量随着pH的增大而减小,随温度的升高而增大,且一定的离子强度有助于吸附剂对腐殖酸的吸附.吸附过程能较好地用准二级动力学模型及Sips等温模型进行拟合.吸附剂在pH 7.0,离子强度0.01 mol·L-1,温度为298 K条件下的最大吸附量可高达238.08 mg·g-1,吸附效果显著,能有效去除水体中的腐殖酸.     

壳聚糖/聚乙二醇/丙烯酸吸附剂对Cu2+、Co2+和Ni2+的吸附选择性和重复利用性

采用扫描电镜(SEM)和红外光谱(FT-IR)对辉光放电电解等离子体(GDEP)技术引发制备的壳聚糖/聚乙二醇/丙烯酸(CS/PEG/AA)聚合物吸附剂的形貌和结构进行了表征.研究了该吸附剂对Cu~(2+)、Co~(2+)和Ni~(2+)的吸附选择性、重复利用性和解吸动力学行为,同时结合X射线光电子能谱(XPS)探讨了可能的吸附机理.结果表明,CS、PEG和AA发生接枝共聚形成聚合物,其表面呈现疏松、多孔的三维网络结构;吸附最佳pH为4.8;在含有Cu~(2+)、Co~(2+)和Ni~(2+)的混合溶液中,CS/PEG/AA对Cu~(2+)有较好的吸附选择性;在EDTA-4Na洗脱液中CS/PEG/AA具有优异的再生和重复利用性,解吸动力学符合解吸准二级模型;Cu~(2+)在CS/PEG/AA上的吸附是由离子交换、配位螯合等共同作用的复杂的物理化学过程.     

基于铁锰泥的除砷颗粒吸附剂制备及其比较

地下水除铁除锰滤池反冲洗铁锰泥具有良好的除砷效果,但因其粉末形态不易固液分离,本文采用高温烘焙法和包埋法以铁锰泥为原料制备颗粒吸附剂,其中包埋法采用烘干和冻干两种干燥方法制粒.结果表明,3种颗粒吸附剂:高温烘焙颗粒吸附剂(GA)、包埋烘干吸附剂(H-GA)和包埋冻干吸附剂(D-GA),表面粗糙,比表面积分别为43. 830、110. 30和129. 18 m~2·g~(-1).吸附实验表明,H-GA和D-GA对砷的吸附远大于GA,GA、H-GA和D-GA最大吸附量分别为5. 05、14. 95和13. 45 mg·g~(-1). Langmuir模型能更好地拟合H-GA和D-GA对砷的吸附,Freundlich模型更好地拟合GA的吸附过程,准一级动力学和准二级动力学模型均能拟合3种吸附剂的动力学数据.酸性环境更有利于砷的吸附.包埋法制备的颗粒吸附剂H-GA和D-GA保留了铁锰泥原始结构,比表面积也远大于GA,因此吸附效果比GA好.两种干燥方式烘干和冻干对吸附没有明显影响.     

高分子壳聚糖对微量金属离子的螯合作用研究

研究了壳聚糖对溶液中Mn2 + 、Fe2 + 、Cu2 + 、Zn2 + 4种常见微量金属离子的吸附作用 ,通过吸附率、溶液pH等参数 ,表征了壳聚糖的吸附能力及其对离子的选择性吸附 ,其选择性次序为 :Cu+ 2 >Zn2 + >Fe+ 2 >Mn+ 2 ,为壳聚糖处理污水中的微量金属离子作了探索。