Study on machinability of a stellite alloy with uncoated and coated carbide tools in turning

Stellite alloys, which have been widely used in the aerospace, automotive and chemical industries, are hard-to-cut cobalt-based materials. This study investigates the machinability of stellite 12 alloys with uncoated carbide cutting tool grades YG610 (K01-K10) and YT726 (K05-K10/M20) and SANDVIK coated carbide tool SNMG150612-SM1105 under dry cutting conditions. Both wear mechanisms and failure modes of the uncoated and coated tools were investigated with turning experiments. The results show that the coated tool SM1105 remarkably outperforms the uncoated tools; and the cutting tool YG610 generally outperforms YT726 under all cutting conditions. Built-up edge was found with YG610 in some cutting conditions and with SM1105 at cutting speed of 16 m/min. Tool surface burning marks were observed on YT726 at relatively higher cutting speeds. Wear develops slowly with coated tools SM1105 until VB reaches 0.2 mm at most conditions (except at v = 43 m/min, f = 0.25 mm/r). Excessive tool flank typically resulted in tool breakage at the cutting edge for uncoated tools. Abrasive and adhesive wear of cutting tools were observed at low cutting speeds while diffusion and chemical wear occurred at higher cutting speeds.     

High speed ball nose end milling of hardened AISI A2 tool steel with PCBN and coated carbide tools

High speed machining (HSM) of tool steels in their hardened state is emerging as an attractive approach for the mold and die industry due to its potential for significant cost savings and productivity improvement. An experimental study was conducted to investigate the tool wear mechanism and surface integrity in high speed ball nose end milling of hardened AISI A2 tool steel using coated tungsten carbide and polycrystalline cubic boron nitride (PCBN) tools. It is found that coated carbide tools can only be used at low speed (120 m/min) while high content PCBN tools are suitable for HSM range (470 m/min). PCBN tools produce a damage free workpiece with better surface finish and less work hardening. Despite the higher tool cost, HSM with PCBN tools lead to reduction in both total cost and production time per part.     

On wear resistance of tool steel

Maintaining a reasonably low cutting tool wear when producing forming tools is a general challenge in the development of new forming tool materials. The tool life of a hot forming tool steel (H13) has been significantly improved by reducing its Si-content from 1.0 to 0.06 wt.%. However, this modified H13 (MH13) also displays a reduced cutting tool life due to higher cutting forces and a stronger tendency to form built up layers (BUE) on the cutting edge. This paper explains why.Gleeble tests of MH13 revealed a significantly higher flow stress in the 820–900 °C temperature interval in MH13 compared to H13. Thermo-Calc simulations showed that when reducing the Si-content from 1.0 to 0.06 wt.% the initial temperature for ferrite-to-austenite transformation (A1) was reduced from 900 °C to 820 °C. Knowing that austenite has totally different mechanical and thermal properties than ferrite, the difference in A1 between the two steels explains the higher cutting forces and higher tendency for BUE-formation. The conclusion is that the difference in machinability between H13 and MH13 is primarily related to their difference in A1.An attempt was also made to find a new tool material composition that can combine the wear resistance of MH13 and the good machinability of H13. Thermo-Calc simulations were performed with slightly modified alloying content without changing its properties as a good forming tool material, with the aim to increase A1. For instance, reducing the Mn content from 0.5 to 0.05 wt.% proved to increase A1 from 820 to 850 °C.     

Micro-flood (MF) technology for sustainable manufacturing operations that are coolant less and occupationally friendly

This paper presents a new technology for minimizing the use of metalworking fluids (MWFs) during the machining process that is atomization-less and occupational friendly. Micro-flood (MF) technology utilizes direct contact between the cutting tool and the MWF without the interaction of a gas medium. Experiments were conducted in high volume mass production environment turning HSLA (high strength low alloy) SAE 070Y steel. Machining performance and total air mass particulates were investigated in dry machining, Near dry machining (NDM) via atomized spray mist and MF technology. Open-atmosphere air monitoring indicated that total mass particulates behaved in an almost linear fashion with respect to gas atomization pressure, whereas the MWF flow rate demonstrated logarithmic trends in NDM applications using an atomized spray. Nozzle orientations directed upward into the air also produced higher mg/m³ concentrations (such as flank) than chip and rake face orientations that were directed down. Greater separation existed at higher gas atomization pressures, MWF flow rates and by changing the MWF type. At extreme limits, nozzle orientation affected mg/m³ concentration as much as 4–5 mg/m³ for water-miscible MWFs and 15–22 mg/m³ for non-water-miscible MWFs. Tool-life performance varied greatly among MWF type and flow rate, and in all cases MF technology performed better than NDM using an atomized spray mist. Direct and consistent MWF penetration to cutting zone using MF technology lowered tool-wear on the average of 12–75% compared to NDM at the same MWF flow rate. Compared to dry machining, NDM improved tool-wear on the average by 20–243%. In one case, tool-wear performance was improved by 616% at 0.15 mm using MF technology compared to dry machining at a nominal 0.925 mm tool-wear. Overall, a large mass reduction of particulates can be achieved employing MF technology that would have been unrealistic for an open-atmosphere machining environment employing an atomized spray mist. On the average, MF technology can maintain a total air mass particulate of less than 0.4 mg/m³ in the occupational work zone using MWF flow rates up to 1260 ml/h, regardless of the MWF classification. Atomized spray mist applications are capable meeting the 5 mg/m³ OSHA limit if MWF flow rates are less than 160 ml/h, air pressures are less than 0.137 MPa (20 psi) using water-miscible MWFs and air pressures are less than 0.0344 MPa (5 psi) using non-water-miscible MWFs.     

The effect of spindle speed,feed-rate and machining time to the surface roughness and burr formation of Aluminum Alloy 1100 in micro-milling operation

This paper describes the characteristics and the cutting parameters performance of spindle speeds (n, rpm) and feed-rates (f, mm/s) during three interval ranges of machining times (t, minutes) with respect to the surface roughness and burr formation, by using a miniaturized micro-milling machine. Flat end-mill tools that have two-flutes, made of solid carbide with Mega-T coated, with 0.2 mm in diameter were used to cut Aluminum Alloy AA1100. The causal relationship among spindle speeds, feed-rates, and machining times toward the surface roughness was analyzed using a statistical method ANOVA. It is found that the feed-rate (f) and machining time (t) contribute significantly to the surface roughness. Lower feed-rate would produce better surface roughness. However, when machining time is transformed into total cut length, it is known that a higher feed-rate, that consequently giving more productive machining since produce more cut length, would not degrade surface quality and tool life significantly. Burr occurrence on machined work pieces was analyzed using SEM. The average sizes of top burr for each cutting parameter selection were analyzed to find the relation between the cutting parameters and burr formation. In this research, bottom burr was found. It is formed in a longer machining time compare the formation of top burr, entrance burr and exit burr. Burr formation is significantly affected by the tool condition, which is degrading during the machining process. This knowledge of appropriate cutting parameter selection and actual tool condition would be an important consideration when planning a micro-milling process to produce a product with minimum burr.     

Finite element modeling of microstructural changes in turning of AA7075-T651 Alloy

The surface characteristics of a machined product strongly influence its functional performance. During machining, the grain size of the surface is frequently modified, thus the properties of the machined surface are different to that of the original bulk material. These changes must be taken into account when modeling the surface integrity effects resulting from machining. In the present work, grain size changes induced during turning of AA7075-T651 (160 HV) alloy are modeled using the Finite Element (FE) method and a user subroutine is implemented in the FE code to describe the microstructural change and to simulate the dynamic recrystallization, with the consequent formation of new grains. In particular, a procedure utilizing the Zener–Hollomon and Hall–Petch equations is implemented in the user subroutine to predict the evolution of the material grain size and the surface hardness when varying the cutting speeds (180–720 m/min) and tool nose radii (0.4–1.2 mm). All simulations were performed for dry cutting conditions using uncoated carbide tools. The effectiveness of the proposed FE model was demonstrated through its capability to predict grain size evolution and hardness modification from the bulk material to machined surface. The model is validated by comparing the predicted results with those experimentally observed.     

Design and evaluation of an atomization-based cutting fluid spray system in turning of titanium alloy

Tool life has been a vital issue in machining titanium alloys. Recently, an atomization-based cutting fluid (ACF) application has been found to be an effective approach for cooling and lubrication in micromachining operations. In this study, an ACF spray system is developed for macro-scale turning of Ti–6Al–4V. The spray system is designed to minimize interaction between the fluid droplets, and the gas nozzle to control the divergence of the fluid droplets. Experiments are conducted to study the effect of five specific ACF spray parameters including fluid flow rate, spray distance, impingement angle, and type and pressure level of the droplet carrier gas on cutting forces, tool life, and chip characteristics. It has been observed that the combination of lower pressure (150 psi) air-mixed CO₂ with a higher flow rate (20 ml/min) and a larger spray distance (35 mm) produces a significantly longer tool life and broken chips. The results also reveal that the ACF spray system can extend tool life up to 40–50% over flood cooling.     

Innovative micro hole machining with minimum burr formation by the use of newly developed micro compound tool

The study focuses on the efforts for minimization of burr formation and improvement of hole surface roughness in micro through-hole machining. It deals with the development of micro compound tool which is consisting of a micro flat drill as the drilling part and a micro diamond-electroplated-grinding part for hole finishing. The finishing diameters of each drilling and grinding parts of the fabricated micro compound tool are 90 μm and 100 μm, respectively. The study focuses mainly on the effect of drill point angle and ultrasonic vibration applied during micro hole machining to the hole entrance and exit burrs formation. The used workpiece is made of stainless steel (SUS304) with a thickness of 100 μm. From the experiment, it was found that the tool having drill point angle of 118° resulted in a smaller burr formation although hole machining was conducted for 600 holes. Furthermore, the application of ultrasonic vibration during hole machining could improve the performance of the developed micro compound tool and decreased the burr size, especially the exit burr.     

High aspect ratio micromachining of glass by electrochemical discharge machining (ECDM)

Micromachining of glass is essential for several microfluidic components, micro-pumps, micro-accelerometers, micro-reactors, micro-fuel cells and several biomedical devices. Unique properties such as high chemical resistance, thermal stability and transparency give glass scope for additional applications. However, poor machinability of glass is a major constraint, especially in high aspect ratio applications of glass in microsystem technology. Micro electrochemical discharge machining (micro ECDM) is an emerging nontraditional fabrication method capable of micromachining ceramic materials like glass. While surface features less than 100 μm have been successfully machined on glass, machining high aspect features is a challenge. Machining accuracy at high depths is severely affected due to overcut and tool wear. In this paper, high aspect ratio microtools fabricated in-house have been used for deep microhole drilling on glass using low electrolyte concentration. An aspect ratio of 11 has been achieved. The results show that lower electrolyte concentration reduced overcut by 22%, thus increasing the aspect ratio of the micro holes. Lowering the electrolyte concentration also reduced the tool wear and hole taper by 39% and 18% respectively.     

Metal-cored arc welding process for joining of modified 9Cr-1Mo (P91) steel

In the present work, metal-cored arc welding process was used for joining of modified 9Cr-1Mo (P91) steel. Metal-cored arc welding process is characterized by high productivity, slag-free process, defect-free weldments that can be produced with ease, and good weldability. Toughness is essential in welds of P91 steel during hydro-testing of vessels. There is a minimum required toughness of 47 J for welds that has to be met as per the EN1557:1997 specification. In the present study, welds were completed using two kinds of shielding gases, each composition being 80% Argon + 20% CO₂, and pure argon respectively. Microstructural characterization and toughness evaluation of welds were done in the as – weld, PWHT at 760 °C – 2 h and PWHT at 760 °C – 5 h conditions. The pure argon shielded welds (‘A2’ and ‘B2’) have higher toughness than 80% argon + 20% CO₂ shielded welds (‘A1’ and ‘B1’). Pure argon shielded welds show less microinclusion content with low volume fraction of δ-ferrite (<2%) phase. Themo-calc windows (TCW) was used for the prediction of equilibrium critical transformation points for the composition of the welds studied. With increase in post-weld heat treatment (PWHT) duration from 2 h to 5 h, there was increase in toughness of welds above 47 J. Using metal-cored arc welding process, it was possible to achieve the required toughness of more than 47 J after PWHT at 760 °C – 2 h in P91 steel welds.     

Aero-lap polishing of poly crystalline diamond inserts using Multicon media

Increasing use of poly crystalline diamond (PCD) inserts as cutting tools and wear parts is vividly seen in automobile, aerospace, marine and precision engineering applications. The PCD inserts undergo series of manufacturing processes such as: grinding that forms the required shape and polishing that gives a fine finish. These operations are not straight forward as PCD is extremely resistant to grinding and polishing. Single crystal diamond can easily be polished by choosing a direction of easy abrasion, but polishing a PCD imposes serious difficulties as the grains are randomly oriented. Prior research on polishing of PCD inserts includes electro discharge grinding (EDG), dynamic friction polishing and grinding by a vitrified bonded diamond wheel. The surface textures of PCD produced using an EDG process often contains: micro cavities, particle pullout, micro-grooves, chipped edges, cracks and gouch marks. While applying the dynamic friction polishing method the PCD material undergoes phase transformation and hence increased polishing rate was apparently seen. However the phase transformation of PCD deteriorates the strength of the insert. Furthermore the inserts produced using the dynamic polishing method often exhibits cracks, chip off and edge damage while using as a cutting tool. Therefore, a new method “aero-lap polishing” was attempted as it applies controlled amount of impinging force by which the surface damage can be significantly reduced. The study did establish an improvement of surface finish of PCD from R_a = 0.55 μm, R_t = 4.5 μm to R_a = 0.29 μm, R_t = 1.6 μm within 15–25 min of polishing time along with significant reduction in surface defects.     

A comparative study on the effect of GTAW processes on the microstructure and mechanical properties of P91 steel weld joints

Modified 9Cr-1Mo (P91) steel is widely used in the construction of power plant components. In the present study, a comparative study on influence of activated flux tungsten inert gas (A-TIG), and gas tungsten arc (GTA) welding processes on the microstructure and the impact toughness of P91 steel welds was carried out. P91 steel welds require a minimum of 47 J during the hydrotesting of vessels as per the EN1557: 1997 specification. Toughness of P91 steel welds was found to be low in the as-weld condition. Hence post-weld heat treatment (PWHT) was carried out on weld with the objective of improving the toughness of weldments. Initially as per industrial practice, PWHT at 760 °C – 2 h was carried out in order to improve the toughness of welds. It has been found that after PWHT at 760 °C – 2 h, GTA weld (132 J) has higher toughness than the required toughness (47 J) as compared with A-TIG weld (20 J). The GTA weld has higher toughness due to enhanced tempering effects due to multipass welding, few microinclusion content and absence of δ-ferrite. The A-TIG weld requires prolonged PWHT (i.e. more than 2 h at 760 °C) than GTA weld to meet the required toughness of 47 J. This is due to harder martensite, few welding passes that introduces less tempering effects, presence of δ-ferrite (0.5%), and more alloy content. After PWHT at 760 °C – 3 h, the toughness of A-TIG weld was improved and higher than the required toughness of 47 J.     

Investigation of chipping and wear of silicon wafer dicing

Wafer dicing chipping and blade wear processes in transient and steady stages were investigated. Dicing blades with two different diamond grit sizes were used to cut wafers. In the cutting experiments, the dicing blades with two different diamond grit sizes were used to cut wafers and for a given type of wafer, the cooling water temperature, cutting feed speed, and rotational speed were fixed. The chipping size, blade surface wear area and surface roughness of the wafer were measured at cutting distances of 50, 150, 300, 975, 1350, and 1900 m, respectively. Cutting debris of cutting distances of 300 m and 1900 m was collected and analyzed. The correlation between blade surface properties and chipping size was investigated. Based on this experimental system, attention is to pay to examine the correlation between blade surface properties and chipping size for transient stage and steady stage. In transient stage, the roughness of dicing blade increases rapidly. This will rapidly increase the chipping size. In steady stage, the chipping size decreases slowly with the decreasing roughness of blade surface. This concludes that blade surface condition is an important factor that affects the chipping size. Moreover, in transient stage, diamond grits that are salient or less bonded to the blade detach leave caves on the blade surface which increases surface roughness of the blade and the chipping size. In steady stage, the heights of grits become even and the chipping size decreases accordingly.     

The Satoyama Index: A biodiversity indicator for agricultural landscapes

Agricultural development to meet rapidly growing demands for food and biofuel and the abandonment of traditional land use have had major impacts on biodiversity. Habitat diversity is one of the most important factors influencing biodiversity in agricultural landscapes. In this study we propose an ecological index of ecosystem or habitat diversity in agricultural landscapes – the Satoyama Index (SI) – that is discernible under appropriate spatial units (e.g., 6 km × 6 km) from 1 km × 1 km gridded land-cover data available from an open-access web site. A high SI value is an indicator of high habitat diversity, which is characteristic of traditional agricultural systems, including Japanese satoyama landscapes, while a low value indicates a monotonic habitat condition typical of extensive monoculture landscapes. The index correlated well with the spatial patterns of occurrence of a bird of prey (Butastur indicus) and species richness of amphibians and damselflies in Japan. The values of the SI also corresponded well to the spatial patterns of typical traditional agricultural landscapes with high conservation value in other countries, for example, the dehesas of the Iberian Peninsula and shade coffee landscapes in Central America. Globally, the pattern of East/South-East Asian paddy belts with their high index values contrasts markedly with the low values of the Eurasian, American, and Australian wheat or corn belts. The SI, which correlates landscapes with biodiversity through potential habitat availability, is highly promising for assessing and monitoring the status of biodiversity irrespective of scale.     

Experimental investigation and characterization of nano-scale dry electro-machining

This paper presents an experimental investigation and characterization of a novel technique of nanoscale electro-machining (EM) in atmospheric air, named dry nano-EM, by using scanning tunneling microscopy (STM) as the platform for nanomachining. The electro-machining has been conducted in near field by maintaining a gap distance of 1–2 nm between the Platinum–Iridium [Pt–Ir (80:20)] tool electrode and atomically flat gold substrate with the air as dielectric medium. An in situ process of evaluating the tool quality before and after machining has been used by monitoring the current–displacement (I–Z) spectroscopy curves. The mechanism of dry nano-EM has been presented as well as the machining performance of the process has been evaluated. Based on the observations, it has been established that field induced evaporation due to intense heat generated at the gap width is the primary mechanism of material removal in dry nano-EM. The experimental results show that dry nano-EM is capable of fabricating consistent nano-features with good repeatability. The volume of material removal increases almost linearly with increasing number of features machined and machining time, indicating the consistency in the dimensions of the nano-features. Finally, dry nano-EM is established as a technique capable of machining 50–100 features in a pre-defined manner with average feature size of 7.5–10 nm in a single pass, thus suitable for nano-patterning in atomically flat electrically conducting surfaces.     

Effect of Silicon Powder Mixed EDM on Machining Rate of AISI D2 Die Steel

In this paper, the effect of silicon powder mixing into the dielectric fluid of EDM on machining characteristics of AISI D2 (a variant of high carbon high chrome) die steel has been studied. Six process parameters, namely peak current, pulse-on time, pulse-off time, concentration of powder, gain, and nozzle flushing have been considered. The process performance is measured in terms of machining rate (MR). The research outcome will identify the important parameters and their effect on MR of AISI D2 in the presence of suspended silicon powder in a kerosene dielectric of EDM. The study indicated that all the selected parameters except nozzle flushing have a significant effect on the mean and variation in MR (S/N ratio). Optimization to maximize MR has also been undertaken using the Taguchi method. The ANOVA analysis indicates that the percentage contribution of peak current and powder concentration toward MR is maximum among all the parameters. The confirmation runs showed that the setting of peak current at a high level (16 A), pulse-on time at a medium level (100 μs), pulse-off time at a low level (15 μs), powder concentration at a high level (4 g/l), and gain at a low level (0.83 mm/s) produced optimum MR from AISI D2 surfaces when machined by silicon powder mixed EDM.     

Energy based phenomenological model for optimizing the sheared edge in the trimming of steels

Attributes related to the dimensional quality of hot rolled steels are very important in commercial sectors that make direct use of this product, because delay or equipment damage can be avoided when forming in downstream operations. In this research, the steel sheet edge trimming process and its relationship with the defect known as broken edge is experimental and numerically studied. The type of material, horizontal clearance between knives and the energy spent during the cutting process are analyzed in detail. A metal-mechanical study is carried out for obtaining a microstructural hardness and flow stress characterization. Consequently, the edge trimming process is FEM simulated and its results in relation to knife penetration and shear stress lead to determining the energy spent during the cutting process. A mathematical model is determined under the consideration that minimum energy gives the optimum cutting conditions. The model proposes a reliable value for the horizontal clearance (H_c), between knives, taking as the principal factors: energy consumed during the edge trimming process, sheet thickness (T_h), carbon content (C) and/or its ultimate tensile strength, expressed as: H_c = α + βT_h − γC. A comparison of the recommended numerical results with the best practical conditions is carried out and a high coincidence is successfully found. This model is expected to be easily adopted as a tool where operators can adjust and control the parameters of process, and then, as a result, produce a sheet without edge trimming defects as well as a reduction in efficiency costs.     

Evaluation of the effectiveness of low frequency workpiece vibration in deep-hole micro-EDM drilling of tungsten carbide

The application of micro-electrical discharge machining (micro-EDM) in deep-hole drilling is still limited due to the difficulty in flushing of debris and unstable machining. Present study introduces a simplistic analytical model to evaluate the effectiveness of low frequency workpiece vibration during the micro-EDM drilling of deep micro-holes. In addition, experimental investigation has been conducted to validate the model by studying the effects of workpiece vibration on machining performance, surface quality and dimensional accuracy of the micro-holes. The effect of vibration frequency and amplitude for three different settings of aspect ratios has been studied experimentally. Moreover, the vibration experiments have been conducted at different levels of gap voltages and capacitances in order to understand the effect of electrical parameters and effectiveness of low-frequency workpiece-vibration at different levels of discharge energies. It has been shown analytically that the effectiveness of low frequency workpiece vibration during micro-EDM drilling can be evaluated by a parameter ‘K_v’ (ratio of maximum acceleration of the vibrating plate in gravitational direction to gravitational acceleration ‘g’), which can be determined from the vibration frequency, amplitude and phase angle of the vibrating workpiece. The theoretical model reveals that for K_v > 1, the position of debris particles will be above the workpiece; thus can be flushed away from machined zone effectively. The experimental reasons for improved micro-EDM drilling performance at the setting of K_v > 1 are found to be the increased effective discharge ratio, reduced short-circuits and improved dielectric flushing. The experimental results also reveal that the low frequency vibration is more effective at the low discharge energy level, thus making it more suitable for micro-EDM. Considering the effect on both the machining characteristics and micro-hole accuracy parameters, vibration frequency of 750 Hz and amplitude of 1.5 μm was found to provide improved performance for the developed vibration device.     

Modelling soil phosphorus decline: Expectations of Water Framework Directive policies

Depletion of plant-available soil phosphorus (P) from excessive to agronomically optimum levels is a measure being implemented in Ireland to reduce the risk of diffuse P transfer from land to water. Within the Nitrates and Water Framework Directive regulations the policy tool is designed to help achieve good status by 2015 in water bodies at risk from eutrophication. To guide expectation, this study used soil plot data from eight common soil associations to develop a model of Soil Test P (STP) (Morgan's extract) decline following periods of zero P amendment. This was used to predict the time required to move from excessive (Index 4) to the upper boundary of the optimum (Index 3) soil P concentration range. The relative P balance (P balance : Total soil P) best described an exponential decline (R² = 63%) of STP according to a backwards step-wise regression of a range of soil parameters. Using annual field P balance scenarios (?30 kg P ha^?1, ?15 kg P ha^?1, ?7 kg P ha^?1), average time to the optimum soil P boundary condition was estimated from a range of realistic Total P and STP starting points. For worst case scenarios of high Total P and STP starting points, average time to the boundary was estimated at 7–15 years depending on the field P balance. However, uncertainty analysis of the regression parameter showed that variation can be from 3 to >20 years. Combined with variation in how soil P source changes translate to resulting P delivery to water bodies, water policy regulators are advised to note this inherent uncertainty from P source to receptor with regard to expectations of Water Framework Directive water quality targets and deadlines.     

Soil-profile organic carbon and total nitrogen during 12 years of pasture management in the Southern Piedmont USA

Soil organic C (SOC) and total soil N (TSN) sequestration estimates are needed to improve our understanding of management influences on soil fertility and terrestrial C cycling related to greenhouse gas emission. We evaluated the factorial combination of nutrient source (inorganic, mixed inorganic and organic, and organic as broiler litter) and forage utilization (unharvested, low and high cattle grazing pressure, and hayed monthly) on soil-profile distribution (0–150 cm) of SOC and TSN during 12 years of pasture management on a Typic Kanhapludult (Acrisol) in Georgia, USA. Nutrient source rarely affected SOC and TSN in the soil profile, despite addition of 73.6 Mg ha^?1 (dry weight) of broiler litter during 12 years of treatment. At the end of 12 years, contents of SOC and TSN at a depth of 0–90 cm under haying were only 82 ± 5% (mean ± S.D. among treatments) of those under grazed management. Within grazed pastures, contents of SOC and TSN at a depth of 0–90 cm were greatest within 5 m of shade and water sources and only 83 ± 7% of maximum at a distance of 30 m and 92 ± 14% of maximum at a distance of 80 m, suggesting a zone of enrichment within pastures due to animal behavior. During 12 years, the annual rate of change in SOC (0–90 cm) followed the order: low grazing pressure (1.17 Mg C ha^?1 year^?1) > unharvested (0.64 Mg C ha^?1 year^?1) = high grazing pressure (0.51 Mg C ha^?1 year^?1) > hayed (?0.22 Mg C ha^?1 year^?1). This study demonstrated that surface accumulation of SOC and TSN occurred, but that increased variability and loss of SOC with depth reduced the significance of surface effects.