Experimental investigation and characterization of nano-scale dry electro-machining

This paper presents an experimental investigation and characterization of a novel technique of nanoscale electro-machining (EM) in atmospheric air, named dry nano-EM, by using scanning tunneling microscopy (STM) as the platform for nanomachining. The electro-machining has been conducted in near field by maintaining a gap distance of 1–2 nm between the Platinum–Iridium [Pt–Ir (80:20)] tool electrode and atomically flat gold substrate with the air as dielectric medium. An in situ process of evaluating the tool quality before and after machining has been used by monitoring the current–displacement (I–Z) spectroscopy curves. The mechanism of dry nano-EM has been presented as well as the machining performance of the process has been evaluated. Based on the observations, it has been established that field induced evaporation due to intense heat generated at the gap width is the primary mechanism of material removal in dry nano-EM. The experimental results show that dry nano-EM is capable of fabricating consistent nano-features with good repeatability. The volume of material removal increases almost linearly with increasing number of features machined and machining time, indicating the consistency in the dimensions of the nano-features. Finally, dry nano-EM is established as a technique capable of machining 50–100 features in a pre-defined manner with average feature size of 7.5–10 nm in a single pass, thus suitable for nano-patterning in atomically flat electrically conducting surfaces.     

Investigating surface roughness,material removal rate and corrosion resistance in PMEDM of γ-TiAl intermetallic

Titanium aluminide intermetallics offer an attractive combination of low density and good oxidation, corrosion and ignition resistance with unique mechanical properties. In this study two series of machining tests are designed. Firstly the powder mixed electrical discharge machining (PMEDM) of γ-TiAl by means of different powders such as aluminum, chrome, silicon carbide, graphite and iron is performed to investigate the output characteristics of surface roughness and topography, material removal rate (MRR), electrochemical corrosion resistance of machined samples and also the machined surfaces are investigated by means of EDS and XRD analyses. Secondly after selection the aluminum powder as the most appropriate kind of powder, the current, pulse on time, powder size and powder concentration are changed in different levels for overall comparison between EDM and PMEDM output characteristics. In the first setting of input machining parameters, aluminum powder improves the surface roughness of TiAl sample about 32% comparing with EDM case and also aluminum particles with the size of 2 μm, in the second setting of input parameters lead to 54% enhancement of MRR comparing with EDM case. The electrochemical corrosion results show that, corrosion resistance of the samples which are machined by graphite and chrome powders respectively are about three and two times more than the sample which is machined without powder.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

The effect of spindle speed,feed-rate and machining time to the surface roughness and burr formation of Aluminum Alloy 1100 in micro-milling operation

This paper describes the characteristics and the cutting parameters performance of spindle speeds (n, rpm) and feed-rates (f, mm/s) during three interval ranges of machining times (t, minutes) with respect to the surface roughness and burr formation, by using a miniaturized micro-milling machine. Flat end-mill tools that have two-flutes, made of solid carbide with Mega-T coated, with 0.2 mm in diameter were used to cut Aluminum Alloy AA1100. The causal relationship among spindle speeds, feed-rates, and machining times toward the surface roughness was analyzed using a statistical method ANOVA. It is found that the feed-rate (f) and machining time (t) contribute significantly to the surface roughness. Lower feed-rate would produce better surface roughness. However, when machining time is transformed into total cut length, it is known that a higher feed-rate, that consequently giving more productive machining since produce more cut length, would not degrade surface quality and tool life significantly. Burr occurrence on machined work pieces was analyzed using SEM. The average sizes of top burr for each cutting parameter selection were analyzed to find the relation between the cutting parameters and burr formation. In this research, bottom burr was found. It is formed in a longer machining time compare the formation of top burr, entrance burr and exit burr. Burr formation is significantly affected by the tool condition, which is degrading during the machining process. This knowledge of appropriate cutting parameter selection and actual tool condition would be an important consideration when planning a micro-milling process to produce a product with minimum burr.     

Micro-flood (MF) technology for sustainable manufacturing operations that are coolant less and occupationally friendly

This paper presents a new technology for minimizing the use of metalworking fluids (MWFs) during the machining process that is atomization-less and occupational friendly. Micro-flood (MF) technology utilizes direct contact between the cutting tool and the MWF without the interaction of a gas medium. Experiments were conducted in high volume mass production environment turning HSLA (high strength low alloy) SAE 070Y steel. Machining performance and total air mass particulates were investigated in dry machining, Near dry machining (NDM) via atomized spray mist and MF technology. Open-atmosphere air monitoring indicated that total mass particulates behaved in an almost linear fashion with respect to gas atomization pressure, whereas the MWF flow rate demonstrated logarithmic trends in NDM applications using an atomized spray. Nozzle orientations directed upward into the air also produced higher mg/m³ concentrations (such as flank) than chip and rake face orientations that were directed down. Greater separation existed at higher gas atomization pressures, MWF flow rates and by changing the MWF type. At extreme limits, nozzle orientation affected mg/m³ concentration as much as 4–5 mg/m³ for water-miscible MWFs and 15–22 mg/m³ for non-water-miscible MWFs. Tool-life performance varied greatly among MWF type and flow rate, and in all cases MF technology performed better than NDM using an atomized spray mist. Direct and consistent MWF penetration to cutting zone using MF technology lowered tool-wear on the average of 12–75% compared to NDM at the same MWF flow rate. Compared to dry machining, NDM improved tool-wear on the average by 20–243%. In one case, tool-wear performance was improved by 616% at 0.15 mm using MF technology compared to dry machining at a nominal 0.925 mm tool-wear. Overall, a large mass reduction of particulates can be achieved employing MF technology that would have been unrealistic for an open-atmosphere machining environment employing an atomized spray mist. On the average, MF technology can maintain a total air mass particulate of less than 0.4 mg/m³ in the occupational work zone using MWF flow rates up to 1260 ml/h, regardless of the MWF classification. Atomized spray mist applications are capable meeting the 5 mg/m³ OSHA limit if MWF flow rates are less than 160 ml/h, air pressures are less than 0.137 MPa (20 psi) using water-miscible MWFs and air pressures are less than 0.0344 MPa (5 psi) using non-water-miscible MWFs.     

Investigation of chipping and wear of silicon wafer dicing

Wafer dicing chipping and blade wear processes in transient and steady stages were investigated. Dicing blades with two different diamond grit sizes were used to cut wafers. In the cutting experiments, the dicing blades with two different diamond grit sizes were used to cut wafers and for a given type of wafer, the cooling water temperature, cutting feed speed, and rotational speed were fixed. The chipping size, blade surface wear area and surface roughness of the wafer were measured at cutting distances of 50, 150, 300, 975, 1350, and 1900 m, respectively. Cutting debris of cutting distances of 300 m and 1900 m was collected and analyzed. The correlation between blade surface properties and chipping size was investigated. Based on this experimental system, attention is to pay to examine the correlation between blade surface properties and chipping size for transient stage and steady stage. In transient stage, the roughness of dicing blade increases rapidly. This will rapidly increase the chipping size. In steady stage, the chipping size decreases slowly with the decreasing roughness of blade surface. This concludes that blade surface condition is an important factor that affects the chipping size. Moreover, in transient stage, diamond grits that are salient or less bonded to the blade detach leave caves on the blade surface which increases surface roughness of the blade and the chipping size. In steady stage, the heights of grits become even and the chipping size decreases accordingly.     

Design and evaluation of an atomization-based cutting fluid spray system in turning of titanium alloy

Tool life has been a vital issue in machining titanium alloys. Recently, an atomization-based cutting fluid (ACF) application has been found to be an effective approach for cooling and lubrication in micromachining operations. In this study, an ACF spray system is developed for macro-scale turning of Ti–6Al–4V. The spray system is designed to minimize interaction between the fluid droplets, and the gas nozzle to control the divergence of the fluid droplets. Experiments are conducted to study the effect of five specific ACF spray parameters including fluid flow rate, spray distance, impingement angle, and type and pressure level of the droplet carrier gas on cutting forces, tool life, and chip characteristics. It has been observed that the combination of lower pressure (150 psi) air-mixed CO₂ with a higher flow rate (20 ml/min) and a larger spray distance (35 mm) produces a significantly longer tool life and broken chips. The results also reveal that the ACF spray system can extend tool life up to 40–50% over flood cooling.     

On wear resistance of tool steel

Maintaining a reasonably low cutting tool wear when producing forming tools is a general challenge in the development of new forming tool materials. The tool life of a hot forming tool steel (H13) has been significantly improved by reducing its Si-content from 1.0 to 0.06 wt.%. However, this modified H13 (MH13) also displays a reduced cutting tool life due to higher cutting forces and a stronger tendency to form built up layers (BUE) on the cutting edge. This paper explains why.Gleeble tests of MH13 revealed a significantly higher flow stress in the 820–900 °C temperature interval in MH13 compared to H13. Thermo-Calc simulations showed that when reducing the Si-content from 1.0 to 0.06 wt.% the initial temperature for ferrite-to-austenite transformation (A1) was reduced from 900 °C to 820 °C. Knowing that austenite has totally different mechanical and thermal properties than ferrite, the difference in A1 between the two steels explains the higher cutting forces and higher tendency for BUE-formation. The conclusion is that the difference in machinability between H13 and MH13 is primarily related to their difference in A1.An attempt was also made to find a new tool material composition that can combine the wear resistance of MH13 and the good machinability of H13. Thermo-Calc simulations were performed with slightly modified alloying content without changing its properties as a good forming tool material, with the aim to increase A1. For instance, reducing the Mn content from 0.5 to 0.05 wt.% proved to increase A1 from 820 to 850 °C.     

Finite element modeling of microstructural changes in dry and cryogenic machining of AZ31B magnesium alloy

Unsatisfactory corrosion resistance is one of the major disadvantages of magnesium alloys that impede their wide application. Microstructural changes, especially grain sizes, of Mg alloys have significant influence on their corrosion resistance. Cryogenic machining was reported to effectively induce grain refinement on Mg alloys and has a potential to improve their corrosion resistance. It is important to model these changes so that proper machining conditions can be found to enhance the corrosion rate of Mg alloys. In this paper, a preliminary study was conducted to model the microstructural changes of AZ31B Mg alloy during dry and cryogenic machining using the finite element (FE) method and a user subroutine based on the dynamic recrystallization (DRX) mechanism of Mg alloys. Good agreement in terms of grain size and affected layer thickness was found between experimental and predicted results. A numerical study was conducted using this model to investigate the influence of rake angle on microstructural changes after cryogenic machining.     

Recycling thin film transistor liquid crystal display (TFT-LCD) waste glass produced as glass–ceramics

The waste electrical and electronic equipment (WEEE) directives are designed to deal with the rapidly increasing waste stream comprised of electrical and electronic equipment. Recycling electrical and electronic equipment reduces the quantity of waste going to final disposal. The demand for thin film transistor liquid crystal display (TFT-LCD) panels, commonly used in everyday electronic products, is increasing. Conventionally adopted treatments of TFT-LCD waste glass cannot meet WEEE directives. This study adopts the following operating conditions in fabricating glass–ceramics: sintering temperature of 800–950 °C; sintering time of 6 h; and, temperature increase rate of 5 °C/min. The glass–ceramic samples then underwent a series of tests, including the Vickers hardness, water absorption and porosity tests, to determine product quality. The Vickers hardness was 12.1 GPa when fired at 900 °C for 6 h, and density was 2.4 g/cm³ and water absorption was 0%. Thus, TFT-LCD waste glass can be regarded as a good glass–ceramic material.     

Innovative micro hole machining with minimum burr formation by the use of newly developed micro compound tool

The study focuses on the efforts for minimization of burr formation and improvement of hole surface roughness in micro through-hole machining. It deals with the development of micro compound tool which is consisting of a micro flat drill as the drilling part and a micro diamond-electroplated-grinding part for hole finishing. The finishing diameters of each drilling and grinding parts of the fabricated micro compound tool are 90 μm and 100 μm, respectively. The study focuses mainly on the effect of drill point angle and ultrasonic vibration applied during micro hole machining to the hole entrance and exit burrs formation. The used workpiece is made of stainless steel (SUS304) with a thickness of 100 μm. From the experiment, it was found that the tool having drill point angle of 118° resulted in a smaller burr formation although hole machining was conducted for 600 holes. Furthermore, the application of ultrasonic vibration during hole machining could improve the performance of the developed micro compound tool and decreased the burr size, especially the exit burr.     

Aero-lap polishing of poly crystalline diamond inserts using Multicon media

Increasing use of poly crystalline diamond (PCD) inserts as cutting tools and wear parts is vividly seen in automobile, aerospace, marine and precision engineering applications. The PCD inserts undergo series of manufacturing processes such as: grinding that forms the required shape and polishing that gives a fine finish. These operations are not straight forward as PCD is extremely resistant to grinding and polishing. Single crystal diamond can easily be polished by choosing a direction of easy abrasion, but polishing a PCD imposes serious difficulties as the grains are randomly oriented. Prior research on polishing of PCD inserts includes electro discharge grinding (EDG), dynamic friction polishing and grinding by a vitrified bonded diamond wheel. The surface textures of PCD produced using an EDG process often contains: micro cavities, particle pullout, micro-grooves, chipped edges, cracks and gouch marks. While applying the dynamic friction polishing method the PCD material undergoes phase transformation and hence increased polishing rate was apparently seen. However the phase transformation of PCD deteriorates the strength of the insert. Furthermore the inserts produced using the dynamic polishing method often exhibits cracks, chip off and edge damage while using as a cutting tool. Therefore, a new method “aero-lap polishing” was attempted as it applies controlled amount of impinging force by which the surface damage can be significantly reduced. The study did establish an improvement of surface finish of PCD from R_a = 0.55 μm, R_t = 4.5 μm to R_a = 0.29 μm, R_t = 1.6 μm within 15–25 min of polishing time along with significant reduction in surface defects.     

Evaluation of the effectiveness of low frequency workpiece vibration in deep-hole micro-EDM drilling of tungsten carbide

The application of micro-electrical discharge machining (micro-EDM) in deep-hole drilling is still limited due to the difficulty in flushing of debris and unstable machining. Present study introduces a simplistic analytical model to evaluate the effectiveness of low frequency workpiece vibration during the micro-EDM drilling of deep micro-holes. In addition, experimental investigation has been conducted to validate the model by studying the effects of workpiece vibration on machining performance, surface quality and dimensional accuracy of the micro-holes. The effect of vibration frequency and amplitude for three different settings of aspect ratios has been studied experimentally. Moreover, the vibration experiments have been conducted at different levels of gap voltages and capacitances in order to understand the effect of electrical parameters and effectiveness of low-frequency workpiece-vibration at different levels of discharge energies. It has been shown analytically that the effectiveness of low frequency workpiece vibration during micro-EDM drilling can be evaluated by a parameter ‘K_v’ (ratio of maximum acceleration of the vibrating plate in gravitational direction to gravitational acceleration ‘g’), which can be determined from the vibration frequency, amplitude and phase angle of the vibrating workpiece. The theoretical model reveals that for K_v > 1, the position of debris particles will be above the workpiece; thus can be flushed away from machined zone effectively. The experimental reasons for improved micro-EDM drilling performance at the setting of K_v > 1 are found to be the increased effective discharge ratio, reduced short-circuits and improved dielectric flushing. The experimental results also reveal that the low frequency vibration is more effective at the low discharge energy level, thus making it more suitable for micro-EDM. Considering the effect on both the machining characteristics and micro-hole accuracy parameters, vibration frequency of 750 Hz and amplitude of 1.5 μm was found to provide improved performance for the developed vibration device.     

Effect of Silicon Powder Mixed EDM on Machining Rate of AISI D2 Die Steel

In this paper, the effect of silicon powder mixing into the dielectric fluid of EDM on machining characteristics of AISI D2 (a variant of high carbon high chrome) die steel has been studied. Six process parameters, namely peak current, pulse-on time, pulse-off time, concentration of powder, gain, and nozzle flushing have been considered. The process performance is measured in terms of machining rate (MR). The research outcome will identify the important parameters and their effect on MR of AISI D2 in the presence of suspended silicon powder in a kerosene dielectric of EDM. The study indicated that all the selected parameters except nozzle flushing have a significant effect on the mean and variation in MR (S/N ratio). Optimization to maximize MR has also been undertaken using the Taguchi method. The ANOVA analysis indicates that the percentage contribution of peak current and powder concentration toward MR is maximum among all the parameters. The confirmation runs showed that the setting of peak current at a high level (16 A), pulse-on time at a medium level (100 μs), pulse-off time at a low level (15 μs), powder concentration at a high level (4 g/l), and gain at a low level (0.83 mm/s) produced optimum MR from AISI D2 surfaces when machined by silicon powder mixed EDM.     

Study on machinability of a stellite alloy with uncoated and coated carbide tools in turning

Stellite alloys, which have been widely used in the aerospace, automotive and chemical industries, are hard-to-cut cobalt-based materials. This study investigates the machinability of stellite 12 alloys with uncoated carbide cutting tool grades YG610 (K01-K10) and YT726 (K05-K10/M20) and SANDVIK coated carbide tool SNMG150612-SM1105 under dry cutting conditions. Both wear mechanisms and failure modes of the uncoated and coated tools were investigated with turning experiments. The results show that the coated tool SM1105 remarkably outperforms the uncoated tools; and the cutting tool YG610 generally outperforms YT726 under all cutting conditions. Built-up edge was found with YG610 in some cutting conditions and with SM1105 at cutting speed of 16 m/min. Tool surface burning marks were observed on YT726 at relatively higher cutting speeds. Wear develops slowly with coated tools SM1105 until VB reaches 0.2 mm at most conditions (except at v = 43 m/min, f = 0.25 mm/r). Excessive tool flank typically resulted in tool breakage at the cutting edge for uncoated tools. Abrasive and adhesive wear of cutting tools were observed at low cutting speeds while diffusion and chemical wear occurred at higher cutting speeds.     

Analytical modelling of residual stresses in orthogonal machining of AISI4340 steel

Residual stress profile in a component is often considered as the critical characteristic as it directly affects the fatigue life of a machined component. This work presents an analytical model for the prediction of residual stresses in orthogonal machining of AISI4340 steel. The novelty of the model lies in the physics-based approach focusing on the nature of contact stresses in various machining zones and the effect of machining temperature. The model incorporates: (i) stresses in three contact regions viz. shear, tool-nose-work piece and tool flank and machined surface, (ii) machining temperature, (iii) strain, strain rate and temperature dependent work material properties, (iv) plastic stresses evaluation by two algorithms, S-J and hybrid, (v) relaxation procedure and (iv) cutting conditions. The model benchmarking shows (86–88%) agreement between the experimental and predicted residual stresses in the X- and Y-directions. On the machined surface, the tensile residual stresses decrease with an increase the edge radius and increase with an increase the cutting speed. However, below the surface, the compressive residual stresses increase with an increase the depth of cut. Further, it is observed that the proposed model with hybrid algorithm gives better results at a lower feed rate, whereas with the S-J algorithm, at a higher feed rate.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Nanosecond pulsed laser micromachining of PMMA-based microfluidic channels

This paper reports an investigation into the effects of nanosecond laser processing parameters on the geometry of microchannels fabricated from polymethylmethacrylate (PMMA). The Nd:YAG solid-state pulsed laser has a wavelength of 1064 nm and a measured maximum power of 4.15 W. The laser processing parameters are varied in a scanning speed range of 400–800 pulses/mm, a pulse frequency range of 5–11 Hz, a Q-switch delay time range of 170–180 μs. Main effects plots and microchannel images are utilized to identify the effects of the process parameters for improving material removal rate and surface quality simultaneously for laser micromachining of microchannels in PMMA polymer. It is observed that channel width and depth decreased linearly with increasing Q-switch delay time (hence average power) and increased non-linearly with higher scanning rates and not much affected by the increase in pulse frequency.     

Energy based phenomenological model for optimizing the sheared edge in the trimming of steels

Attributes related to the dimensional quality of hot rolled steels are very important in commercial sectors that make direct use of this product, because delay or equipment damage can be avoided when forming in downstream operations. In this research, the steel sheet edge trimming process and its relationship with the defect known as broken edge is experimental and numerically studied. The type of material, horizontal clearance between knives and the energy spent during the cutting process are analyzed in detail. A metal-mechanical study is carried out for obtaining a microstructural hardness and flow stress characterization. Consequently, the edge trimming process is FEM simulated and its results in relation to knife penetration and shear stress lead to determining the energy spent during the cutting process. A mathematical model is determined under the consideration that minimum energy gives the optimum cutting conditions. The model proposes a reliable value for the horizontal clearance (H_c), between knives, taking as the principal factors: energy consumed during the edge trimming process, sheet thickness (T_h), carbon content (C) and/or its ultimate tensile strength, expressed as: H_c = α + βT_h − γC. A comparison of the recommended numerical results with the best practical conditions is carried out and a high coincidence is successfully found. This model is expected to be easily adopted as a tool where operators can adjust and control the parameters of process, and then, as a result, produce a sheet without edge trimming defects as well as a reduction in efficiency costs.     

CaCO3 production using liquid waste from Solvay method

Process of obtaining CaCO₃ from the waste post-distillation liquid DS and post-filtration liquid from Solvay method of the soda production at 303 K was investigated. Reagents were dosed in a stoichiometric ratio without dilution, for different concentrations of the DS and post-filtration liquids. The dosage time was varied in the range 2–30 min, the reagent stirring rate was 500 rpm. For the obtained samples of CaCO₃, the bulk and packing densities, water, paraffin oil and dibutyl phthalate absorption capacities, distribution of the particle size as well as the crystalline form were determined.