Experimental investigation of turning AISI 1045 steel using cryogenic carbon dioxide as the cutting fluid

The intensive temperatures in high speed machining not only limit the tool life but also impair the machined surface by inducing tensile residual stresses, microcracks and thermal damage. This problem can be handled largely by reducing the cutting temperature. When the conventional coolant is applied to the cutting zone, it fails to remove the extent of the heat effectively. Hence, a cryogenic coolant is highly recommended for this purpose. In this paper, an attempt has been made to use cryogenic carbon dioxide (CO₂) as the cutting fluid. Experimental investigations are carried out by turning AISI 1045 steel in which the efficiency of cryogenic CO₂ is compared to that of dry and wet machining with respect to cutting temperature, cutting forces, chip disposal and surface roughness. The experimental results show that the application of cryogenic CO₂ as the cutting fluid is an efficient coolant for the turning operation as it reduced the cutting temperature by 5%–22% when compared with conventional machining.It is also observed that the surface finish is improved to an appreciable amount in the finished work piece on the application of cryogenic CO₂. The surface finish is improved by 5%–25% in the cryogenic condition compared with wet machining.     

Experimental investigation of the machining induced residual stress tensor under mechanical loading

Residual stress induced by machining is complex and difficult to predict, since it involves mechanical loads, temperature gradients or phase transformation in the generation mechanism. In this work, an experiment with a statistical design for the residual stress tensor was performed to investigate the residual stress profile on a machined surface. In order to understand the generation mechanism of residual stress in machining, three variables and workpiece materials were carefully selected to focus on the mechanical loads and avoid the temperature gradients and phase transformation on the machined surface. The mechanical loads considered here included the chip formation force at the primary shear zone and the plowing force at the tool tip–workpiece contact. Depths of cut and rake angles were selected to alter the chip formation force, and the tool tip radius was designed to emphasize the plowing effect. The workpiece material was aluminum 3003. The experimental results showed that the chip formation force provides basic shapes of the residual stress profile for a machined surface. It decides the depth of the peak residual stress below the surface. However, the plowing force was the dominating effect on the surface residual stress, causing high stresses on the surface. The plowing force can shift the surface stress from tensile to compressive. Additionally, the measured stress tensor proved that in-plane shear stress exists for the machined surface.     

Analysis of machined surface quality in a single-pass of ball-end milling on Inconel 718

The ball-end milling process is widely used for generating three-dimensional sculptured surfaces with definite curvature. In such cases, variation of surface properties along the machined surface curvatures is not well understood. Therefore, this paper reports the effect of machining parameters on the quality of surface obtained in a single-pass of a ball-end milling cutter with varying chip cross-sectional area. This situation is analogous to generation of free form cavities, pockets, and round fillets on mould surfaces. The machined surfaces show formation of distinct bands as a function of instantaneous machining parameters along the periphery of cutting tool edge, chip compression and instantaneous shear angle. A distinct variation is also observed in the measured values of surface roughness and micro-hardness in these regions. The maximum surface roughness is observed near the tool tip region on the machined surface. The minimum surface roughness is obtained in the stable cutting zone and it increases towards the periphery of the cutter. Similar segmentation was observed on the deformed chips, which could be correlated with the width of bands on the machined surfaces. The sub-surface quality analysis in terms of micro-hardness helped define machining affected zone (MAZ). The parametric effects on the machining induced shear and residual stresses have also been evaluated.     

Parametric glass milling with simultaneous control

Parametric glass milling is presented to machine periodical circular channels on the glass plates for manufacturing micro testing devices. An end mill traverses in the linear motion during the workpiece rotation, which are synchronized by simultaneous control. The glass milling is controlled by 4 parameters in a mathematical model without NC program. Based on the principle of the parametric machining and the effect of the cutter axis inclination on the cutting process, a milling machine was developed to perform the parametric glass milling with an inclined ball end mill. The cutter axis inclination and the actual feed rate are associated with the critical feed rate, the maximum feed rate at which a crack-free surface is finished. As a machining example, a periodical circular channel was machined with a transparent surface by the simultaneous control.     

Prediction of polycrystalline materials texture evolution in machining via Viscoplastic Self-Consistent modeling

The crystallographic orientation or anisotropy is one of the main microstructural attributes strongly affecting the mechanical properties of materials. It is also an influential parameter to be considered during the manufacturing process especially for ultra-precision machining since it affects part quality, tool performance, and process productivity through material properties. In this study, a prediction toolset constituted of a Viscoplastic Self-Consistent model and machining process mechanics model is used to predict the texture evolution on the machined surface. The VPSC (Viscoplastic Self-Consistent) methodology which uses the mechanisms of slip and twinning that are active in single crystals of arbitrary symmetry was used. For this, an analytical model for the process mechanics is derived to understand the forces and stresses generated by the cutting tool at each workpiece point, then the strain and strain rate to capture the rate at which the material is deforming and finally the crystallographic orientations under various machining conditions. Experiments were performed on the orthogonal cutting of aluminum alloy AA-7075-T651 and the texture results were compared to model predictions.     

Finite element modeling of microstructural changes in turning of AA7075-T651 Alloy

The surface characteristics of a machined product strongly influence its functional performance. During machining, the grain size of the surface is frequently modified, thus the properties of the machined surface are different to that of the original bulk material. These changes must be taken into account when modeling the surface integrity effects resulting from machining. In the present work, grain size changes induced during turning of AA7075-T651 (160 HV) alloy are modeled using the Finite Element (FE) method and a user subroutine is implemented in the FE code to describe the microstructural change and to simulate the dynamic recrystallization, with the consequent formation of new grains. In particular, a procedure utilizing the Zener–Hollomon and Hall–Petch equations is implemented in the user subroutine to predict the evolution of the material grain size and the surface hardness when varying the cutting speeds (180–720 m/min) and tool nose radii (0.4–1.2 mm). All simulations were performed for dry cutting conditions using uncoated carbide tools. The effectiveness of the proposed FE model was demonstrated through its capability to predict grain size evolution and hardness modification from the bulk material to machined surface. The model is validated by comparing the predicted results with those experimentally observed.     

The effect of spindle speed,feed-rate and machining time to the surface roughness and burr formation of Aluminum Alloy 1100 in micro-milling operation

This paper describes the characteristics and the cutting parameters performance of spindle speeds (n, rpm) and feed-rates (f, mm/s) during three interval ranges of machining times (t, minutes) with respect to the surface roughness and burr formation, by using a miniaturized micro-milling machine. Flat end-mill tools that have two-flutes, made of solid carbide with Mega-T coated, with 0.2 mm in diameter were used to cut Aluminum Alloy AA1100. The causal relationship among spindle speeds, feed-rates, and machining times toward the surface roughness was analyzed using a statistical method ANOVA. It is found that the feed-rate (f) and machining time (t) contribute significantly to the surface roughness. Lower feed-rate would produce better surface roughness. However, when machining time is transformed into total cut length, it is known that a higher feed-rate, that consequently giving more productive machining since produce more cut length, would not degrade surface quality and tool life significantly. Burr occurrence on machined work pieces was analyzed using SEM. The average sizes of top burr for each cutting parameter selection were analyzed to find the relation between the cutting parameters and burr formation. In this research, bottom burr was found. It is formed in a longer machining time compare the formation of top burr, entrance burr and exit burr. Burr formation is significantly affected by the tool condition, which is degrading during the machining process. This knowledge of appropriate cutting parameter selection and actual tool condition would be an important consideration when planning a micro-milling process to produce a product with minimum burr.     

Evaluation of vegetable based cutting fluids with extreme pressure and cutting parameters in turning of AISI 304L by Taguchi method

Many problems such as health and environment issues are identified with the use of cutting fluids (CFs). There has been a high demand for developing new environmentally friendly CFs such as vegetable based cutting fluids (VBCFs) to reduce these harmful effects. In this study, performances of six CFs, four different VBCFs from sunflower and canola oils with different ratios of extreme pressure (EP) additives, and two commercial types of CFs (semi-synthetic and mineral) are evaluated for reducing of surface roughness, and cutting and feed forces during turning of AISI 304L austenitic stainless steel with carbide insert tool. Taguchi’s mixed level parameter design (L₁₈) is used for the experimental design. Cutting fluid, spindle speed, feed rate and depth of cut are considered as machining parameters. Regression analyses are applied to predict surface roughness, and cutting and feed forces. ANOVA is used to determine effects of the machining parameters and CFs on surface roughness, cutting and feed forces. In turning of AISI 304L, effects of feed rate and depth of cut are found to be more effective than CFs and spindle speed on reducing forces and improving the surface finish. Performances of VBCFs and commercial CFs are also compared and results generally show that sunflower and canola based CFs perform better than the others.     

Micro dimple milling on cylinder surfaces

The paper presents a micro dimple machining on a cylinder surface with a two-flutes ball end mill. When the cutter axis is inclined and the depth of cut is less than the tool radius, non-cutting time, during which neither of the two cutting edges contacts the workpiece, appears in a rotation of the cutter. The rotation of the workpiece and the feed of the tool are controlled so that the cutting areas do not overlap each other. In order to incline the tool with respect to the tangential direction on the cylinder surface, the tool is located at a position oriented at 45° from the top of the cylinder. An analytical model is presented to control the shapes of the dimples with the cutting parameters. The presented machining is verified in cutting tests with measuring the shape and the profile of the dimples. Pre-machining operations are conducted to have a high cylindricity of the workpiece in longitudinal turning and polishing. The cutter runout of the tool is also eliminated by adjusting the orientation and the position of the tool in the collet chuck with measuring the cutting force. The micro dimples are machined accurately as they are simulated.     

Modeling and optimization of turning duplex stainless steels

The attractive combination of high mechanical strength, good corrosion resistance and relatively low cost has contributed to making duplex stainless steels (DSSs) one of the fastest growing groups of stainless steels. As the importance of DSSs is increasing, practical information about their successful machining is expected to be crucial. To address this industrial need, standard EN 1.4462 and super EN 1.4410 DSSs are machined under constant cutting speed multi-pass facing operations. A systematic approach which employs different modeling and optimization tools under a three phase investigation scheme has been adopted. In phase I, the effect of design variables such as cutting parameters, cutting fluids and axial length of cuts are investigated using the D-Optimal method. The mathematical models for performance characteristics such as; percentage increase in radial cutting force (%F_r), effective cutting power (P_e), maximum tool flank wear (VB_max) and chip volume ratio (R) are developed using response surface methodology (RSM). The adequacy of derived models for each cutting scenario is checked using analysis of variance (ANOVA). Parametric meta-heuristic optimization using Cuckoo search (CS) algorithm is then performed to determine the optimum design variable set for each performance. In the phase II, comprehensive experiment-based production cost and production rate models are developed. To overcome the conflict between the desire of minimizing the production cost and maximizing the production rate, compromise solutions are suggested using Technique for Order Preference by Similarity to Ideal Solution (TOPSIS). The alternatives are ranked according to their relative closeness to the ideal solution. In the phase III, expert systems based on fuzzy rule modeling approach are adopted to derive measures of machining operational sustainability called operational sustainability index (OSI). Artificial neural network (ANN) based models are developed to study the effect of design variables on computed OSIs. Cuckoo search neural network systems (CSNNS) are finally utilized to constrainedly optimize the cutting process per each cutting scenario. The most appropriate cutting setup to ensure successful turning of standard EN 1.4462 and super EN 1.4410 for each scenario is selected in accordance with conditions which give the maximum OSI.     

Machining evaluation of a hybrid MQL-CO2 grinding technology

Although there are already successful industrial experiences in other machining industries with the elimination of coolants, this is not so in the grinding industry due to the large amounts of generated heat that must be evacuated from the contact zone. In this work, a new approach to the elimination of fluids in grinding is presented. The technology is based on the use of a hybrid Minimum Quantity of Lubricant (MQL)-low temperature CO₂ system that reduces lubrication consumption. Abrasive grits are protected by the layer of frozen oil, resulting in a significant improvement in grinding wheel life and surface quality of the machined component. Although the cooling action is reduced with respect to the conventional coolant, no thermal damage was observed on the workpiece.     

AFM probe based nano mechanical scribing of soda-lime glass

In recent years, demands for miniature components have increased due to their reduced size, weight and energy consumption. In particular, brittle materials such as glass can provide high stiffness, hardness, corrosion resistance and high-temperature strength for various biomedical and high-temperature applications. In this study, cutting properties and the effects of machining parameters on the ductile cutting of soda-lime glass are investigated through the nano-scale scratching process. In order to understand the fundamentals of the material removal mechanism at the atomic scale, such as machined surface quality, cutting forces and the apparent friction, theoretical investigation along with experimental study are needed. Scribing tests have been performed using a single crystal diamond atomic force microscope (AFM) probe as the scratching tool, in order to find the cutting mechanism of soda-lime glass in the nano-scale. The extended lateral force calibration method is proposed to acquire accurate lateral forces. The experimental thrust and cutting forces are obtained and apparent friction coefficients are deduced. The effects of feed rates and the ploughing to shearing transition of soda-lime glass have been investigated.     

Machining assessment of nano-crystalline hydroxyapatite bio-ceramic

Hydroxyapatite (HAP) is a widely used bio-ceramic in the fields of orthopedics and dentistry. This study investigates the machinability of nano-crystalline HAP (nHAP) bio-ceramic in end milling operations, using uncoated carbide tool under dry cutting conditions. Efforts are focused on the effects of various machining conditions on surface integrity. A first order surface roughness model for the end milling of nHAP was developed using response surface methodology (RSM), relating surface roughness to the cutting parameters: cutting speed, feed, and depth of cut. Model analysis showed that all three cutting parameters have significant effect on surface roughness. However, the current model has limited statistical predictive power and a higher order model is desired. Furthermore, tool wear and chip morphology was studied. Machined surface analysis showed that the surface integrity was good, and material removal was caused by brittle fracture without plastic flow.     

Three-dimensional laser machining of structural ceramics

Three- dimensional laser machining of structural ceramics such as alumina (Al₂O₃), silicon nitride (Si₃N₄), silicon carbide (SiC) and magnesia (MgO) was carried out using a 1.06 μm wavelength pulsed Nd:YAG laser. The rate of machining predicted in terms of material removed per unit time (mg/s) increased with an increase in heating rate (K/s). A thermal model based on temperature dependent absorptivity and thermophysical properties, in addition to conduction, convection and radiation based heat transfer, was developed to predict material removal rate. Predicted values were compared with actual measurements made from machined cavities. Such a study would enable advance predictions of the laser processing conditions required to machine cavities of desired dimensions.     

An experimental investigation into micro ball end-milling of silicon

Silicon is a representative operational material for semiconductor and micro-electronics. In certain MEMS applications, it is required to fabricate three dimensional channels and complex pattern on silicon substrate. Such features are typically fabricated by photolithography and chemical etching. These processes have low productivity and have certain other limitations. Therefore, a viable switch-over from non-traditional fabrication processes to traditional machining is highly desired for improved productivity in high-mix low-volume production. However, machining of silicon by traditional process is extremely difficult due to its high brittleness. Even very small forces produced during machining can cause brittle fracture on silicon surface resulting in deteriorated surface quality. The fundamental principle in machining of a brittle material such as silicon is to achieve material removal through plastic deformation rather than crack propagation. This paper presents the experimental results of ductile-mode machining of silicon by micro ball end-milling. The workpiece surface was inclined to the rotational axes of the cutter to improve the surface finish. It was established experimentally that 15-μm deep, fracture-free slots can be machined on silicon wafer by micro ball end-milling if the feed rate is below a certain threshold. The influence of several machining parameters on the roughness of machined-surface was also investigated. Cubic boron nitride (CBN) is presented as much economical alternative tool-material to single-crystal diamond for machining silicon in ductile-mode.     

Cutting tool temperatures in interrupted cutting—The effect of feed-direction modulation

Transient tool temperatures in interrupted machining processes were investigated. The initial focus was feed-direction modulated turning. Here, the instantaneous uncut chip thickness (IUCT) was modeled including the regenerative effect introduced by the modulation. Treating the tool as a one-eighth semi-infinite body, for a rectangular heat patch governed by the IUCT at the corner, the tool heat conduction problem was solved. The Green’s function solution procedure included heat convection from exterior surfaces. The results indicated that modulation lowered the cutting temperature, more significantly at a higher modulation frequency. However, heat conduction into the tool dominated over convection to the ambient. The IUCT was found to lag the peak temperature, indicating that modulation can possibly alter the thermal softening of the cutting tool in continuous cutting without a concomitant decrease in material removal rate. The same tool temperature model applied to face-milling indicated that the peak temperature occurred only at cut exit. Carefully planned interrupted hard-facing experiments were performed varying the frequency and duration of interruption. Tool-life data confirmed the beneficial effects of lower cutting temperatures due to slight interruption.     

Effect of Tool Edge Geometry on Workpiece Subsurface Deformation and Through-Thickness Residual Stresses for Hard Turning of AISI 52100 Steel

An experimental investigation was conducted to determine the effect of tool cutting edge geometry on workpiece subsurface deformation and through-thickness residual stresses for finish hard turning of through-hardened AISI 52100 steel. Polycrystalline cubic boron nitride (PCBN) inserts with “up-sharp” edges, edge hones, and chamfers were used as the cutting tools in this study. Examination of the workpiece microstructure reveals that large edge hone tools produce substantial subsurface plastic flow. Flow is not observed when turning with small edge hone tools or chamfered tools, and the workpiece microstructure appears random for these cases. Examination of through-thickness residual stresses shows that large edge hone tools produce deeper, more compressive residual stresses than are produced by small edge hone tools or chamfered tools. Explanations for these effects are offered based on assumed contact conditions between the tool and workpiece.     

Investigating surface roughness,material removal rate and corrosion resistance in PMEDM of γ-TiAl intermetallic

Titanium aluminide intermetallics offer an attractive combination of low density and good oxidation, corrosion and ignition resistance with unique mechanical properties. In this study two series of machining tests are designed. Firstly the powder mixed electrical discharge machining (PMEDM) of γ-TiAl by means of different powders such as aluminum, chrome, silicon carbide, graphite and iron is performed to investigate the output characteristics of surface roughness and topography, material removal rate (MRR), electrochemical corrosion resistance of machined samples and also the machined surfaces are investigated by means of EDS and XRD analyses. Secondly after selection the aluminum powder as the most appropriate kind of powder, the current, pulse on time, powder size and powder concentration are changed in different levels for overall comparison between EDM and PMEDM output characteristics. In the first setting of input machining parameters, aluminum powder improves the surface roughness of TiAl sample about 32% comparing with EDM case and also aluminum particles with the size of 2 μm, in the second setting of input parameters lead to 54% enhancement of MRR comparing with EDM case. The electrochemical corrosion results show that, corrosion resistance of the samples which are machined by graphite and chrome powders respectively are about three and two times more than the sample which is machined without powder.     

Performance-Based Predictive Models and Optimization Methods for Turning Operations and Applications: Part 3—Optimum Cutting Conditions and Selection of Cutting Tools

This paper presents a summary of recent developments in developing performance-based machining optimization methodologies for turning operations. Four major machining performance measures (cutting force, tool wear/tool life, chip form/chip breakability, and surface roughness) are considered in the present work, which involves the development and integration of hybrid models for single and multi-pass turning operations with and without the effects of progressive tool wear. Nonlinear programming techniques were used for single-pass operations, while a genetic algorithms approach was adopted for multi-pass operations. This methodology offers the selection of optimum cutting conditions and cutting tools for turning with complex grooved tools.     

3D numerical investigation of thermally assisted high efficiency ductile machining of nanocrystalline hydroxyapatite

This study investigates the effects of four different variables (initial workpiece temperature, side rake angle, edge radius/feed rate, and nose radius/depth of cut) on ductile regime machining of a bioceramic material known as nanohydroxyapatite (nano-HAP) using 3D numerical simulation. AdvantEdge FEM Version 5.9 is used to conduct turning simulations of the nano-HAP workpiece. Tecplot 360 is used to analyze the results of the simulations. Because the workpiece is thin, the entire workpiece is set to a uniform initial temperature to simulate laser preheating of the material. Initial workpiece temperature, rake angle (side rake angle), edge radius, and nose radius are varied, and the effects of these operating conditions on critical feed are investigated. It is found that critical feed increases as initial workpiece temperature increases, and also as negativity of rake angle increases. For the edge radius, it is concluded that an initial increase causes an increase in critical feed – however, at some value of edge radius, critical feed shows no further increase; for the nose radius, critical feed appears to show no significant dependence.