Treating both wastewater and excess sludge with an innovative process

The innovative process consists of biological unit for wastewater treatment and ozonation unit for excess sludge treatment. An aerobic membrane bioreactor( MBR ) was used to remove organics and nitrogen, and an anaerobic reactor was added to the biological unit for the release of phosphorus contained at aerobic sludge to enhance the removal of phosphorus. For the excess sludge produced in the MBR, which was fed to ozone contact column and reacted with ozone, then the ozonated sludge was returned to the MBR for further biological treatment. Experimental results showed that this process could remove organics, nitrogen and phosphorus efficiently, and the removals for COD, NH3-N, TN and TP were 93.17%, 97.57%, 82.77% and 79.5%, respectively. Batch test indicated that the specific nitrification rate and specific denitrifieation rate of the MBR were 1.03 mg NH3-N/(gMLSS^ h) and 0.56 mg NOx-N/(gMLSS^ h), and denitrification seems to be the rate-limiting step. Under the test conditions, the sludge concentration in the MBR was kept at 5000--6000 rng/L, and the wasted sludge was ozenated at an ozone dosage of 0.10 kgO3/kgSS. During the experimental period of two months, no excess sludge was wasted, and a zero withdrawal of excess sludge was implemented. Through economic analysis, it was found that an additional ozonation operating cost for treatment of both wastewater and excess sludge was only 0. 045 RMB Yuan( USD 0.0054)/m^3 wastewater.     

好氧颗粒污泥膜生物反应器的运行特性

以人工合成模拟废水对好氧颗粒污泥膜生物反应器(MBR)的运行特性和膜污染进行了研究.结果表明:在HRT为6h,溶氧浓度为4～6mg.L^-1,COD的容积负荷为7.24kg·(m³·d)^-1的条件下,COD的去除率可达96%以上.当NH₃-N的容积负荷为0.17kg·(m³·d)^-1时,NH₃-N的去除率可达60%.COD/N比的变化,对好氧颗粒污泥MBR的COD及NH₃-N去除率基本没有影响.稳定运行过程时,MBR中好氧颗粒污泥浓度(MLSS)基本维持在14～16mg·L^-1.较高的污泥浓度和颗粒污泥内部缺氧和厌氧环境的存在,使MBR中硝化和反硝化过程能同时存在.同时,比较了2种不同形态的活性污泥(颗粒污泥和絮状污泥)在MBR运行过程中膜通量的变化趋势,结果表明,颗粒污泥MBR膜通量的下降速度明显比絮状污泥MBR的下降速度慢很多,且通过空气反冲或用水清洗即可使通量基本恢复.     

兼氧型MBR工艺对污泥自消化效果的研究

研究了兼氧型MBR工艺中,当溶解氧控制在0.1～3.0 mg/L时,兼性厌氧菌和厌氧菌所占比例达80%。实验进水COD浓度为60～600 mg/L,COD去除率平均达93%;MLVSS浓度一直保持稳定,平均值为11 090 mg/L,而无机灰分浓度逐渐积累,实验开始时为3 107 mg/L,实验结束时达5 830 mg/L。结果表明,兼氧型MBR工艺可实现污泥自消化,不排放有机性污泥。兼氧型MBR工艺还对膜组件有一定自清洁作用,运行周期可达4个月。实验证明,兼氧型MBR工艺具有处理效率高、不排放有机污泥以及减轻膜污染的特点,是一种创新性的污水处理技术。     

Treatment of a dyeing wastewater from a woolen mill using an A/O membrane bio-reactor

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｄｙｅｉｎｇｗａｓｔｅｗａｔｅｒｏｆｗｏｏｌｅｎｍｉｌｌｃｏｎｔａｉｎｓａｌｏｔｋｉｎｄｓｏｆｐｏｌｌｕｔａｎｔｓ,ｓｕｃｈａｓａｃｉｄｉｃｄｙｅｓ,ｄｉｓｐｅｒｓｅｄｙｅｓ,ｍｏｒｄａｎｔｄｙｅｓ,ａｕｘｉｌｉａｒｉｅｓ,ｓａｌｔｓａｎｄｓｏｏｎ .Ｔｈｅｅｆｆｌｕｅｎｔｓｆｒｏｍｗａｓｔｅｗａｔｅｒｔｒｅａｔｍｅｎｔｐｌａｎｔｓｆｏｒｔｒｅａｔｍｅｎｔｏｆｔｈｅｄｙｅｉｎｇｗａｓｔｅｗａｔｅｒｏｆｗｏｏｌｅｎｍｉｌｌｓｗｉｔｈｎｏｒｍａｌｂｉｏｌｏｇｉｃａｌｐｒｏｃｅ…     

Treatment of a dyeing wastewater from a woolen mill using an A/O membrane bio-reactor

An anaerobic/oxic membrane bioreactor (A/O MBR) was used for treatment of dyeing wastewater from a woolen mill.COD and color of the wastewater were 54-473 mg/L and 40-400 dilution time (DT) respectively. The ratio of BOD5/COD was less than 0.13. By the A/O MBR process, the average removal of COD, BOD5, color and turbidity was 82％, 96％, 71％ and 99％, respectively. The average COD, BOD5, color and turbidity of effluent was 37 nag/L, 0.8 mg/L, 40 DT and 0.44 NUT respectively. The effluent COD met the local standard of reuse water in Beijing, China. The average COD volume load of the anaerobic biological tank was 0. 0483 kgCOD/(m3·d) and that of the aeration tank of the MBR was 0. 3589 kgCOD/(m3·d). The sludge load of the MBR was 0.19 kgCOD/(kg· MLSS· d) on average and the maximum of that was 0.4 kgCOD/( kg· MLSS· d).The flux of the A/O membrane bioreactor could be remained at larger than 50 L/(h· m2· 0.1MPa). The results indicated that A/O membrane bioreactor has technical feasibility for treatment of woolen mill wastewater.     

UASB-MBR组合工艺处理模拟黄连素废水

采用升流式厌氧污泥床-膜生物反应器(UASB-MBR)组合工艺处理模拟黄连素废水,模拟废水中有机污染物由葡萄糖和黄连素配制,以葡萄糖作为初级能源物质,通过微生物协同降解作用去除废水中的黄连素.在水力停留时间(HRT)为24 h,进水ρ(COD_Cr),ρ(NH₄+-N)和ρ(黄连素)分别为1 717～4 393,91.8～158.7和64.4～276.8 mg/L,废水中黄连素的ρ(COD_Cr)贡献率为7.5%～25.0%的条件下,组合工艺可实现ρ(COD_Cr),ρ(NH₄+-N)和ρ(黄连素)的去除率分别为92.5%～95.9%,67.0%～98.9%和99%以上,废水中黄连素主要通过UASB去除,去除率为95.2%～98.9%.在进水COD_Cr负荷为0.54～1.88 kg/(m3·d),黄连素负荷为0.71～12.42 g/(m3·d)的条件下,MBR可保证出水ρ(COD_Cr),ρ(黄连素)和ρ(NH₄+-N)分别低于50,1.0和2.0 mg/L;随着MBR进水ρ(黄连素)升至3.45～12.42 mg/L,在黄连素的微生物毒性胁迫作用下,MBR中污泥呈由分散态向聚集态的转变.      

膜生物反应器处理毛纺废水的中试研究

采用中试规模(10t/d)的厌氧-好氧膜生物反应器(A/O MBR)处理毛纺印染废水.当HRT为7h,进水COD、BOD₅分别为179～358mg/L和44.8～206mg/L,试验系统对COD、BODs、色度、浊度的平均去除率分别为92.1%、98.4%、60.7%、98.9%,出水水质浓度或指标值分别为20.2mg/L、1.6mg/L、25倍、0.51 NTU.出水水质指标达到建设部生活杂用水水质标准(CJ25.1-89).A/O MBR工艺处理毛纺印染废水技术可行、操作简单、易于管理,可为工业规模应用提供技术参考.     

蠕虫在膜生物反应器和活性污泥法中的污泥减量研究

通过长达345d的中试规模试验,研究比较了蠕虫在膜生物反应器(MBR)和活性污泥法(CAS)的生长状况及其导致的污泥减量效果.CAS中的蠕虫生长状况明显优于MBR的蠕虫生长状况.MBR曝气池中平均蠕虫密度(10条·mg-1)远低于CAS曝气池中平均蠕虫密度(71条·mg-1),并且CAS中蠕虫连续保持高密度(>30条·mg-1)生长达172d.CAS中红斑瓢体虫和仙女虫交替成为优势蠕虫.蠕虫生长对MBR的污泥产率(0 40kg·kg-1)和污泥沉降性能(污泥沉降指数133mL·g-1)影响很小,但却能显著减少CAS的污泥产率(0 17kg·kg-1)和改善污泥沉降性能(污泥沉降指数为60mL·g-1).仙女虫比红斑瓢体虫能更大地减少污泥产量和更好地改善污泥沉降性能.蠕虫生长不影响MBR的COD去除率和出水水质,但却显著影响CAS的COD去除率和出水水质.     

EGSB-MBR组合工艺处理糖蜜发酵废水效能研究

实验采用厌氧膨胀颗粒污泥床(EGSB)反应器与好氧膜生物反应器(MBR)组合工艺对糖蜜发酵废水进行处理.重点考察了组合工艺对发酵废水的处理效能,包括甲烷的产生效率、污染物(COD、NH4+-N和TN)的去除效能.实验结果表明:控温条件下[(35±1)℃]、进水COD约为2250mg/L、pH在为6.0左右时,EGSB对发酵废水的COD去除率可达75.6%,甲烷的容积产气速率为0.48m3/(m3·d).MBR在溶解氧(DO)为1~2mg/L左右时,采用曝气-搅拌交替运行方式处理EGSB出水,可以实现同步硝化反硝化,并且在曝气3h-搅拌1h交替运行条件下,NH4+-N、TN去除率分别为85.13%、58.57%,而最终COD去除率达到85%.     

一体化工艺中反硝化聚磷菌比例测定研究

反硝化聚磷菌可以在缺氧条件下利用硝酸盐氮和亚硝酸盐氮作为电子受体完成吸磷过程,确定反硝化聚磷菌比例对于强化反硝化除磷作用具有重要意义。从一体化活性污泥工艺中取污泥混合液,加入蔗糖合200mg/LCOD后进行厌氧搅拌,2h后将厌氧污泥分成三等份,其中两份分别加入10mg/LNO3--N、10mg/LNO2--N后缺氧搅拌2h,另一份用充氧仪曝气2h。根据厌氧、缺氧/好氧交替过程中不同电子受体下的除磷量,可以简便的确定反硝化聚磷菌在全部聚磷菌中的比例,结果表明该一体化工艺中反硝化聚磷菌在全部聚磷菌中的比例达到98.92%。     

膜-生物反应器和传统活性污泥工艺的比较

在运行条件一致的情况下把膜-生物反应器(MBR)和传统活性污泥工艺(CAS)进行了比较研究.试验结果表明,MBR具有比CAS更为稳定良好的出水水质,其平均出水COD浓度为55.5mg/L,低于CAS工艺(79.7mg/L).MBR系统中由于膜对大分子物质的截留作用,运行前120d出现溶解性微生物产物的积累,但随着微生物的驯化,这些积累的微生物产物最后得到降解.CAS中未发生微生物产物的积累.CAS出水、MBR上清液以及MBR出水中的物质组成差别很大.CAS出水和MBR上清液中分子量大于60000的高分子物质与小于3000的小分子物质都占有相当大的比例,其中高分子物质在MBR上清液中的含量高于CAS系统;MBR出水中则主要是分子量小于3000的小分子物质.MBR污泥粒径较小,使得氧扩散速率得到提高.     

UAFB-缺氧-好氧MBR组合工艺处理生活污水效能研究

为了同时达到从生活污水中回收能源性气体和深度处理生活污水的目的,试验采用升流式厌氧污泥固定床(up-flowanaerobic fixed bed,UAFB)-缺氧-好氧膜生物反应(membrane bioreactor,MBR)组合工艺处理生活污水.试验重点研究了组合工艺对生活污水的处理效能,包括能源性气体的产生效能、对污染物质的处理效能以及对污泥浓度的控制.UAFB-缺氧-好氧MBR组合工艺在温度20℃、厌氧HRT为3 h、缺氧HRT为3 h、好氧HRT为3.5 h的条件下运行,甲烷气体的产生量为1.55L/d,COD去除率为93.28%,NH 4+-N去除率为90.60%,UAFB出水VFAs总量54.74 mg/L,TN去除率为45.51%.试验发现,组合工艺可以长期维持反应器内较低的污泥浓度,大大减小了剩余污泥的处理量,在一定程度上实现了污泥减量化,同时较低的污泥浓度有利于缓解膜污染.     

Ozonation of refractory chemicals in leachate with hydrogen peroxide

Nearly 97% of organic chemicals in Hong Kong leachate could be effectively removed by the UASB( upflow anaerobic sludge blanket) process followed by the fenton coagulation. The COD of leachate was lowered from an average of 12900 mg/L to 1440 mg/L after the UASB treatment, and was further lowered to 394 mg/L after the fenton coagulation. The remaining refractory residues could be further removed by ozonation with the addition of H2Oz. The ozonation for the supernatant of the fenton coagulation was most effective at pH 7-8, with the addition of 300 mg/L of H202, and 30 min of reaction. The final effluent contained only 85 mg/L of COD and 10 mg/L of BOD5. On the other hand, direct ozonation of UASB effluent lowered the COD to 905 mg/L and BOD5 to 103 mg/L. Ozonation improved the biodegradability of the organic residues, and also converted oart of oruanic-N in the leachate into NH3-N and NO3^- -N.     

一种垃圾渗滤液的处理技术

本文采用厌氧反应器UASB+膜生物反应器MBR+纳滤工艺处理垃圾填埋场废水,设计处理能力为100m3/d,在进水CODs:和BODs分别为10 000 mg/L和5 000 mg/L时,经处理后,出水CODc:和BODs分别为60mg/L和20mg/L,其去除率分别为99.4%和99.6%,且出水稳定,达到了<北京市水...     

好氧-沉淀-厌氧工艺剩余污泥减量性能和机理研究

探讨了污泥衰减、能量解偶联、低污泥产率厌氧反应对OSA工艺污泥减量作用的影响.结果表明,污泥衰减是由微生物死亡及吸附于污泥表面的颗粒有机物水解酸化和微生物内源代谢2部分组成.间歇试验污泥厌氧过程中,上清液SCOD、NH 4-N、TP浓度均随厌氧时间逐渐升高,OSA污泥厌氧16 h后溶解性蛋白质高达33.09 mg/L,上升幅度高于多糖浓度的变化,证实了污泥水解现象.OSA污泥内源SOUR可达8 mg/(g·h),是CAS污泥内源SOUR的1.7倍以上,说明OSA系统中较高的内源代谢促使污泥减量.污泥衰减是OSA工艺污泥减量的决定性原因,可占OSA污泥减量效果的66.7%左右.间歇实验证实了OSA系统由于厌氧一好氧耦合环境,存在能量解偶联现象,但由于这种作用引发的污泥减量仅占7.5%左右.OSA工艺污泥厌氧池释放的SCOD作为缺氧反硝化、厌氧释磷、硫酸盐还原及产甲烷的二次基质,由于这些厌氧反应污泥产率低于好氧代谢,使得系统污泥产率下降,约有23.5%的污泥减量是源于这种因素.OSA污泥减量是由多方面因素综合作用的结果.     

pH值调控柠檬酸污泥厌氧发酵产酸及碳源潜力研究

以柠檬酸废水厌氧颗粒污泥为接种物,在不同pH值调控条件下开展柠檬酸生产废水剩余活性污泥厌氧发酵产酸研究。通过对发酵液挥发性脂肪酸(VFAs)、有机质、氮磷和污泥脱水性能的分析,探讨了柠檬酸污泥厌氧产酸机制。结果表明,pH³10的碱性条件更有利于有机质的溶出从而促进VFAs的产生。三维荧光光谱分析发现在恒定pH值下腐殖酸(HA)和富里酸(FA)会大量溶出降低VFAs的产量。初始pH=10是柠檬酸污泥厌氧产酸的最佳pH值,发酵4d的VFAs浓度最高达(6681.47±126.82)mg COD/L,是文献报道中市政污泥产酸量的近2倍,其中乙酸占比49.8%,发酵后产酸功能菌Chloroflexi、Bacteroidota的相对丰度分别由初始的9.52%、10.87%增至16.84%、14.39%,污泥归一化毛细吸水时间(n_CST)为(11.34±0.27)s×L/g,脱水性能良好,发酵液TP浓度为(20.45±0.33)mg/L。研究表明,利用柠檬酸剩余活性污泥碱性厌氧发酵产酸作为污水处理过程中的外加碳源具有较大潜力。     

臭氧在中试规模污泥原位减量中的应用

为探究高、低浓度臭氧旁路处理对中试系统出水水质、污泥减量率的影响,采用两组系统(对照组:厌氧/缺氧/好氧(A/A/O),试验组:A/A/O+臭氧旁路处理)在5个工况下运行183d.结果表明,利用剂量为13mg/g MLSS(25mg/g MLVSS)臭氧处理占生物反应池容积20％的回流污泥时,系统运行性能良好;在此操作...     

污泥浓度对双重后置反硝化工艺脱氮除磷的影响

利用城市实际污水考察了ρ(MLSS)在2 400、3 350、4 300和5 250 mg/L 4种工况下SBR反应器(厌氧/好氧/缺氧/再好氧/沉淀/排水/预缺氧运行模式)的脱氮除磷效果,并分析了反应器单个周期内有机物、氮和磷的转化过程及污泥产量. 结果表明:ρ(MLSS)由2 400 mg/L升至5 250 mg/L时,系统TN去除率由52.5%升至66.6%;后续缺氧及预缺氧工序的脱氮比例(该工序TN去除量占系统TN总去除量的比例)由12.7%增至23.1%;ρ(MLSS)为4 300 mg/L时系统TP去除率(75.6%)达到最大. 后续缺氧及预缺氧工序中,ρ(MLSS)与内源反硝化速率呈正相关(R2=0.703 7);提高ρ(MLSS)可使PAOs(聚磷菌)在下一个周期内获得更多的碳源,使厌氧释磷量由1.62 mg/L升至9.10 mg/L,但PAOs吸磷动力会减弱,对除磷不利. 在后置反硝化、污泥衰减、能量解偶联等减量机制共同作用下,ρ(MLSS)为4 300 mg/L时系统污泥减量可提高24.4%. 从脱氮除磷及污泥减量效果综合考虑,ρ(MLSS)是双重后置反硝化工艺重要的控制参数,在该研究条件下控制在4 300 mg/L最优.      

膜生物反应器与传统活性污泥反应器内生物群落特征

采用膜生物反应器(MBR)和传统活性污泥法(CAS)2种反应器处理相同的生活污水,考察了MBR和CAS的运行和生物群落结构及其动态变化.结果表明,MBR对COD和氨氮的去除效率均比CAS高, MBR和CAS出水COD的平均值分别为39.6 mg/L和62.9 mg/L,出水氨氮的平均值分别为6.8 mg/L和14.5 mg/L,可以看出无论是对于有机物还是NH⁺₄-N,MBR的去除效果都比CAS要好.由于MBR的污泥处于大的曝气剪切力、过低的污泥负荷、以及长SRT导致的各种惰性物质积累等环境中,使MBR中污泥的群落及其变化与CAS相比有明显的不同.随着反应器运行时间的增加,DGGE的结果表明MBR的种群数量始终高于CAS, MBR群落相似性系数的变化也比CAS要大很多,在第15、 124、 186和230　d时,MBR的条带数分别是22、 25、 24和20条,而CAS在相应的运行时间时条带数分别为19、 14、 17和20条.MBR污泥与种泥的相似性系数分别是54.1%、 63.7%、 63.9%和66.8%,而CAS污泥与种泥的相似性系数分别是71.8%、 61.4%、 9.1%和65.9%.说明CAS的排泥导致非选择性的微生物流失,同时,也说明MBR的群落具有更好的适应环境因素变化的能力,这是MBR抗冲击负荷能力较强的原因之一.从戴丝系数来看,尽管群落相似性越来越高,但群落始终处于变化状态,说明环境的微小变化（进水水质、环境温度等）都会引起生物群落的变化.     

Production and application of anaerobic granular sludge produced by landfill

Sludge granulation is considered to be the most critical parameter governing successful operation of an upflow anaerobic sludge blanket and expanded granular sludge bed(EGSB)reactors.Pre-granulated seeding sludge could greatly reduce the required start- up time.Two lab-scale and a pilot-scale EGSB reactors were operated to treat Shaoxing Wastewater Treatment Plant(SWWTP) containing wastewater from real engineering printing and dyeing with high pH and sulfate concentration.The microbiological structure and the particle size distribution in aerobic excess sludge,sanitary landfill sludge digested for one year,and the granular sludge of EGSB reactor after 400 d of operation were analyzed through scanning electron microscopy (SEM) and sieves.The lab-scale EGSB reactor seeded with anaerobic sludge after digestion for one year in landfill showed obviously better total chemical oxygen demand (TCOD)removal efficiency than one seeded with aerobic excess sludge after cation polyacrylamide flocculation-concentration and dehydration.The TCOD removed was 470.8 mg/L in pilot scale EGSB reactor at short hydraulic retention time of 15 h.SEM of sludge granules showed that the microbiological structure of the sludge from different sources showed some differences.SEM demonstrated that Methanobacterium sp.was present in the granules of pilot-scale EGSB and the granular sludge produced by landfill contained a mixture of anaerobic/anoxic organisms in abundance.The particle size distribution in EGSB demonstrated that using anaerobic granular sludge produced by sanitary landfill as the seeding granular sludge was feasible.