Photo-induced surface frustrated Lewis pairs for promoted photocatalytic decomposition of perfluorooctanoic acid

● Terminal carboxylate group activation is PFOA degradation’s rate-limiting step. ● Bi₃O(OH)(PO₄)₂ with surface frustrated Lewis pairs (SFLPs) efficiently degrade PFOA. ● Photo-induced Lewis acidic sites and proximal surface hydroxyls constitute SFLPs. ● SFLPs act as collection centers to effectively adsorb PFOA. ● SFLPs endow accessible pathways for photogenerated holes rapid transfer to PFOA. Heterogeneous photocatalysis has gained substantial research interest in treating per- and polyfluoroalkyl substances (PFAS)-contaminated water. However, sluggish degradation kinetics and low defluorination efficiency compromise their practical applications. Here, we report a superior photocatalyst, defected Bi₃O(OH)(PO₄)₂, which could effectively degrade typical PFAS, perfluorooctanoic acid (PFOA), with high defluorination efficiency. The UV light irradiation could in situ generate oxygen vacancies on Bi₃O(OH)(PO₄)₂ through oxidation of the lattice hydroxyls, which further promotes the formation of Lewis acidic coordinately unsaturated bismuth sites. Then, the Lewis acidic sites couple with the proximal surface hydroxyls to constitute the surface frustrated Lewis pairs (SFLPs). With the in-depth spectroscopic analysis, we revealed that the photo-induced SFLPs act as collection centers to effectively adsorb PFOA and endow accessible pathways to transfer photogenerated holes to PFOA rapidly. Consequently, activation of the terminal carboxyl, a rate-limiting step for PFOA decomposition, could be easily achieved over the defected Bi₃O(OH)(PO₄)₂ photocatalyst. These results suggest that SFLPs exhibit great potential in developing highly efficient photocatalysts to degrade persistent organic pollutants.     

Revealing the GHG reduction potential of emerging biomass-based CO2 utilization with an iron cycle system

● Greenhouse gas mitigation by biomass-based CO₂ utilization with a Fe cycle system. ● The system including hydrothermal CO₂ reduction with Fe and Fe recovery by biomass. ● The reduction potential quantified by experiments, simulations, and an ex-ante LCA. ● The greatest GHG reduction potential is −34.03 kg CO₂-eq/kg absorbed CO₂. ● Ex-ante LCA supports process optimization to maximize GHG reduction potential. CO₂ utilization becomes a promising solution for reducing anthropogenic greenhouse gas (GHG) emissions. Biomass-based CO₂ utilization (BCU) even has the potential to generate negative emissions, but the corresponding quantitative evaluation is limited. Herein, the biomass-based CO₂ utilization with an iron cycle (BCU-Fe) system, which converts CO₂ into formate by Fe under hydrothermal conditions and recovers Fe with biomass-derived glycerin, was investigated. The GHG reduction potential under various process designs was quantified by a multidisciplinary method, including experiments, simulations, and an ex-ante life-cycle assessment. The results reveal that the BCU-Fe system could bring considerable GHG emission reduction. Significantly, the lowest value is −34.03 kg CO₂-eq/kg absorbed CO₂ (−2.44 kg CO₂-eq/kg circulated Fe) with the optimal yield of formate (66%) and Fe (80%). The proposed ex-ante evaluation approach not only reveals the benefits of mitigating climate change by applying the BCU-Fe system, but also serves as a generic tool to guide the industrialization of emerging carbon-neutral technologies.     

Highly effective visible-photocatalytic hydrogen evolution and simultaneous organic pollutant degradation over an urchin-like oxygen-doped MoS2/ZnIn2S4 composite

● An urchin-like OMS/ZIS composite was fabricated by a facile solvothermal method. ● The OMS/ZIS exhibits superior photocatalytic H₂ evolution for organics degradation. ● A probable mechanism of dual-functional photocatalysis was proposed in detail. ● This work provides an inspiration for rational design of dual-functional catalysts. Achieving hydrogen production and simultaneous decomposition of organic pollutants through dual-functional photocatalytic reactions has received increasing attention due to the environmentally friendly and cost-effective characteristics of this approach. In this work, an urchin-like oxygen-doped MoS₂/ZnIn₂S₄ (OMS/ZIS) composite was fabricated for the first time using a simple solvothermal method. The unique microstructure with abundant active sites and fast charge transfer channels further shortened the charge migration distance and compressed carrier recombination. The obtained composite exhibited an efficient H₂ evolution reaction rate of 12.8 mmol/g/h under visible light, which was nearly times higher than pristine ZnIn₂S₄, and the apparent quantum efficiency was 14.9% (420 nm). The results of the simultaneous photocatalytic H₂ evolution and organic pollutant decomposition test were satisfactory, resulting in decomposition efficiencies of resorcinol, tetracycline, and bisphenol A that reached 41.5%, 63.5%, and 53.0% after 4 h, respectively, and the highest H₂ evolution rate was 672.7 μmol/g/h for bisphenol A. Furthermore, natural organic matter (NOM) abundantly found in actual water was adopted as an electron donor for H production under simulated sunlight irradiation, indicating the promising practicability of simultaneous hydrogen evolution and NOM decomposition. Moreover, the mechanisms of the dual-purpose photocatalytic reactions, as well as the synergistic effect between the molecular structures of the organic pollutants and the corresponding adsorption behavior on the photocatalyst surface were illustrated in detail. These obtained results may serve as an inspiration for the rational design of highly efficient, dual-functional photocatalysts in the future.     

Electrocatalytic reduction of nitrate using Pd-Cu modified carbon nanotube membranes

● Pd-Cu modified CNT membranes were prepared successfully by electrodeposition method. ● The deposition voltage and deposition time were optimized for Pd-Cu co-deposition. ● NO₃⁻-N was removed efficiently from water by Pd-Cu modified CNT membranes. ● The presence of dissolved oxygen did not affect the nitrate reduction performance. ● Mass transfer rate was promoted significantly with the increase in membrane flux. Excessive nitrate in water is harmful to the ecological environment and human health. Electrocatalytic reduction is a promising technology for nitrate removal. Herein, a Pd-Cu modified carbon nanotube membrane was fabricated with an electrodeposition method and used to reduce nitrate in a flow-through electrochemical reactor. The optimal potential and duration for codeposition of Pd and Cu were −0.7 V and 5 min, respectively, according to linear scan voltammetry results. The membrane obtained with a Pd:Cu ratio of 1:1 exhibited a relatively high nitrate removal efficiency and N₂ selectivity. Nitrate was almost completely reduced (~99 %) by the membrane at potentials lower than −1.2 V. However, −0.8 V was the optimal potential for nitrate reduction in terms of both nitrate removal efficiency and product selectivity. The nitrate removal efficiency was 56.2 %, and the N₂ selectivity was 23.8 % for the Pd:Cu=1:1 membrane operated at −0.8 V. Nitrate removal was enhanced under acidic conditions, while N₂ selectivity was decreased. The concentrations of Cl⁻ ions and dissolved oxygen showed little effect on nitrate reduction. The mass transfer rate constant was greatly improved by 6.6 times from 1.14 × 10⁻³ m/h at a membrane flux of 1 L/(m²·h) to 8.71 × 10⁻³ m/h at a membrane flux of 15 L/(m²·h), which resulted in a significant increase in the nitrate removal rate from 13.6 to 133.5 mg/(m²·h). These findings show that the Pd-Cu modified CNT membrane is an efficient material for nitrate reduction.     

Enhancement of extracellular Cr(VI) reduction for anammox recovery using hydrazine: performance,pathways, and mechanism

● N₂H₄ addition enhanced and recovered anammox performance under Cr(VI) stress. ● N₂H₄ accelerated electron transfer of Cr(VI) reduction for detoxification. ● N₂H₄ enhanced anammox metabolism for activity recovery from Cr(VI) inhibition. ● Extracellular Cr(VI) reduction to less toxic Cr(III) was the dominant mechanism. The hexavalent chromium (Cr(VI)) would frequently impose inhibition to anaerobic ammonium oxidation (anammox) process, hindering the efficiency of nitrogen removal in wastewater treatment. Hydrazine (N₂H₄), which is an intermediate product of anammox, participates in intracellular metabolism and extracellular Cr(VI) reduction. However, the roles of N₂H₄-induced intracellular metabolism and extracellular reduction in nitrogen removal under Cr(VI) stress remain unclear. The addition of 3.67 mg/L of N₂H₄ increased the anammox activity by 17%. As an intermediate, N₂H₄ enhanced anammox metabolism by increasing the heme c content and electron transfer system activity. As a reductant, N₂H₄ accelerated the reduction of c-Cyts-mediated extracellular Cr(VI) to the less toxic Cr(III). Extracellular Cr(III) accounts for 74% of the total Cr in a Cr(VI)-stressed anammox consortia. These findings highlight that N₂H₄-induced extracellular Cr(VI) reduction is the dominant mechanism for the survival of anammox consortia. We also found that N₂H₄ increased the production of extracellular polymeric substances to sequester excessive Cr(VI) and produced Cr(III). Taken together, the study findings suggest a potential strategy for enhancing nitrogen removal from ammonium-rich wastewater contaminated with Cr(VI).     

Recent advances in electrochemical decontamination of perfluorinated compounds from water: a review

● Recent advances in the electrochemical decontamination of PFAS are reviewed. ● Underlying mechanisms and impacting factors of these processes are discussed. ● Several novel couped systems and electrode materials are emphasized. ● Major knowledge gaps and research prospects on PFAS removal are identified. Per- and polyfluoroalkyl substances (PFAS) pose serious human health and environmental risks due to their persistence and toxicity. Among the available PFAS remediation options, the electrochemical approach is promising with better control. In this review, recent advances in the decontamination of PFAS from water using several state-of-the-art electrochemical strategies, including electro-oxidation, electro-adsorption, and electro-coagulation, were systematically reviewed. We aimed to elucidate their design principles, underlying working mechanisms, and the effects of operation factors (e.g., solution pH, applied voltage, and reactor configuration). The recent developments of innovative electrochemical systems and novel electrode materials were highlighted. In addition, the development of coupled processes that could overcome the shortcomings of low efficiency and high energy consumption of conventional electrochemical systems was also emphasized. This review identified several major knowledge gaps and challenges in the scalability and adaptability of efficient electrochemical systems for PFAS remediation. Materials science and system design developments are forging a path toward sustainable treatment of PFAS-contaminated water through electrochemical technologies.     

Impacts of backwashing on micropollutant removal and associated microbial assembly processes in sand filters

● Backwashing in sand filters with 2-h and 4-h EBCTs was simulated. ● Removal efficiency of five micropollutants recovered within 2 d at 2-h EBCT. ● Active biomass of sand filters recovered within 2 d under two EBCTs. ● Microbial composition gradually recovered to pre-backwashing level at 2-h EBCT. ● Recovered microbes only accounted for 15.55 %–25.69 % in the sand filters at 4-h EBCT. Backwashing is crucial for preventing clogging of sand filters. However, few studies have investigated the effect of backwashing on micropollutant removal and the dynamic changes in the microbial community in sand filters. Here, we used a series of manganese and quartz sand filters under empty bed contact times (EBCTs) of 2 h and 4 h to explore variations in micropollutant degradation and temporal dynamics of the microbial community after backwashing. The results showed that the removal efficiencies of caffeine, sulfamethoxazole, sulfadiazine, trimethoprim, atrazine, and active biomass recovered within 2 d after backwashing in both types of sand filters at 2-h EBCT, but the recovery of sulfadiazine and trimethoprim was not observed at 4-h EBCT. Moreover, the removal efficiency of atenolol increased after backwashing in the manganese sand filters, whereas maintained almost complete removal efficiency in the quartz sand filters at both EBCTs. Pearson correlation analysis indicated that microbial community composition gradually recovered to the pre-backwashing level (R increased from 0.53 to 0.97) at 2-h EBCT, but shifted at 4-h EBCT (R < 0.25) after backwashing. Furthermore, the compositions of the recovered, depleted, and improved groups of microbes were distinguished by applying hierarchical clustering to the differentially abundant amplicon sequence variants. The cumulative relative abundance of recovered microbes at 2-h EBCT was 82.76 % ± 0.43 % and 46.82 % ± 4.34 % in the manganese and quartz sand filters, respectively. In contrast, at 4-h EBCT, the recovered microbes dropped to 15.55 %–25.69 % in both types of sand filters.     

Decoding and quantitative detection of antibiotics by a luminescent mixed-lanthanide-organic framework

● A series of mixed-LOFs and portable LOF-fibers were synthesized. ● LOF-S3 was selected as a luminescent sensor for antibiotics. ● Mixed-LOF was capable of decoding antibiotics by emission intensity ratios. ● Linear relationship between antibiotic concentration and I545nm/I618nm was observed. Due to the potential risk of antibiotics to the environment, the development of inexpensive, simple, and reliable antibiotic detection methods is significant but also faces challenges. In this work, several lanthanide-organic frameworks (LOFs), constructed from lanthanide ions (Eu³⁺ and/or Tb³⁺) and 1,3,5-benzene-tricarboxylic acid (BTC), were synthesized by solvothermal method. LOF-S3 with comparable emission peaks of ⁵D₄ → ⁷F₅ (Tb³⁺, 545 nm) and ⁵D₀ → ⁷F₂ (Eu³⁺, 618 nm) was selected as a luminescent sensor. In this system, the highly efficient energy transferred from the organic linker to lanthanide ions and from Tb³⁺ to Eu³⁺ occurs. LOF-S3 sensor was capable of decoding antibiotics by distinguishable emission intensity ratios. Therefore, a two-dimensional decoded map of antibiotics was established. The linear relationship between antibiotic concentration and emission intensity ratio indicated the quantitative determination of antibiotics was feasible. As a typical analyte, the response mechanism of nalidixic acid (NA) was investigated in detail. The competition of NA and BTC for UV light absorption, as well as the binding propensity of NA and Tb, affected the organic linkers-to-lanthanide ions and Tb-to-Eu energy transfer, resulting in the change of fluorescence intensity ratio. The self-calibrating mixed-LOF sensor overcame the uncontrollable errors of the traditional absolute emission intensity method and generated stable luminescent signals in multiple cycles. Furthermore, the integration of LOF-S3 with polymer fibers enabled the formation of a LOF-polymer fibrous composite with fluorescence detection capability, which is a promising portable sensor for practical applications.     

Electroconductive RGO-MXene membranes with wettability-regulated channels: improved water permeability and electro-enhanced rejection performance

● Electroconductive RGO-MXene membranes were fabricated. ● Wettable membrane channels were established between RGO and MXene nanosheets. ● Hydrophilic MXene reduces the resistance of water entering the membrane channels. ● Water permeance of RGO-MXene membrane is 16.8 times higher than that of RGO membrane. ● Electro-assistance can enhance the dye rejection performance of RGO-MXene membrane. Reduced graphene oxide (RGO) membranes are theoretically more conducive to the rapid transport of water molecules in their channels compared with graphene oxide (GO) membranes, as they have fewer oxygen-containing functional groups and more non-oxidized regions. However, the weak hydrophilicity of RGO membranes inhibits water entry into their channels, resulting in their low water permeability. In this work, we constructed wettable RGO-MXene channels by intercalating hydrophilic MXene nanosheets into the RGO membrane for improving the water permeance. The RGO-MXene composite membrane exhibits high pure water permeance of 62.1 L/(m²·h·bar), approximately 16.8 times that of the RGO membrane (3.7 L/(m²·h·bar)). Wettability test results and molecular dynamics simulations suggest that the improved water permeance results from the enhanced wettability of RGO-MXene membrane and increased rate of water molecules entering the RGO-MXene channels. Benefiting from good conductivity, the RGO-MXene membrane with electro-assistance exhibits significantly increased rejection rates for negatively charged dyes (from 56.0% at 0 V to 91.4% at 2.0 V for Orange G) without decreasing the permeate flux, which could be attributed to enhanced electrostatic repulsion under electro-assistance.     

Numerical modeling and performance evaluation of passive convergence-permeable reactive barrier (PC-PRB)

● A 2D finite-element solute transport model, PRB-Trans, is developed. ● PC-PRB can significantly improve the remediation efficiency of PRB. ● PC-PRB can considerably reduce the required PRB dimensions and materials costs. ● The required PRB length decreases with the increase of pipe length, L _p. The passive convergence-permeable reactive barrier (PC-PRB) was proposed to address the limitations of traditional PRB configurations. To evaluate the hydraulic and pollutant removal performance of the PC-PRB system, we developed a simulation code named PRB-Trans. This code uses the two-dimensional (2D) finite element method to simulate groundwater flow and solute transport. Case studies demonstrate that PC-PRB technology is more efficient and cost-effective than continuous permeable reactive barrier (C-PRB) in treating the same contaminated plume. Implementation of PC-PRB technology results in a 33.3% and 72.7% reduction in PRB length (L_PRB) and height (H_PRB), respectively, while increasing 2D horizontal and 2D vertical pollutant treatment efficiencies of PRB by 87.8% and 266.8%, respectively. In addition, the PC-PRB technology has the ability to homogenize the pollutant concentration and pollutant flux through the PRB system, which can mitigate the problems arising from uneven distribution of pollutants in the C-PRB to some extent. The L_PRB required for PC-PRB decreases as the water pipe length (L_p) increases, while the H_PRB required initially decreases and then increases with increasing L_p. The effect of passive well height (H_w) on H_PRB is not as significant as that of L_p on H_PRB. Overall, PC-PRB presents a promising and advantageous PRB configuration in the effective treatment of various types of contaminated plumes.     

Separation/degradation behavior and mechanism for cationic/anionic dyes by Ag-functionalized Fe3O4-PDA core-shell adsorbents

● PDA-Fe₃O₄-Ag was made by hydrothermal and oxidation self-polymerization method. ● PDA-Fe₃O₄-Ag had great magnetic separation performance. ● PDA-Fe₃O₄-Ag had good adsorption and degradation performance for ionic dyes. ● PDA-Fe₃O₄-Ag showed NR and MO degradation potential of 91.2% and 87.5%, respectively. High-performance adsorbents have been well-studied for the removal of organic dye pollutants to promote environment remediation. In this study, an Ag nanoparticle-functionalized Fe₃O₄-PDA nanocomposite adsorbent (PDA-Fe₃O₄-Ag) was synthesized, and the adsorption/separation performance of commonly used cationic and anionic organic dyes by the PDA-Fe₃O₄-Ag adsorbent were assessed. Overall, PDA-Fe₃O₄-Ag exhibited a significantly higher adsorption capacity for cationic dyes compared to anionic dyes, the highest of which was more than 110.0 mg/g (methylene blue (MB)), which was much higher than not only the adsorption capacities of the anionic dyes in this study but also other dye adsorption capacities reported in the literature. The dye adsorption kinetics data fitted well to both the pseudo second-order kinetics model and the Langmuir isotherm model, suggesting a monolayer-chemisorption-dominated adsorption mode. Thermodynamics analysis indicated that the adsorption process was both endothermic and spontaneous. Furthermore, the PDA-Fe₃O₄-Ag adsorbent achieved high photodegradation removal rates of the dyes, especially neutral red (NR) and methyl orange (MO), which were 91.2% and 87.5%, respectively. With the addition of PDA-Fe₃O₄-Ag, the degradation rate constants of NR and MO increased from 0.08 × 10⁻² and 0 min⁻¹ to 2.11 × 10⁻² and 1.73 × 10⁻² min⁻¹, respectively. The high adsorption and photocatalytic degradation performance of the PDA-Fe₃O₄-Ag adsorbent make it an excellent candidate for removing cationic and anionic dyes from the industrial effluents.     

Effectiveness of tertiary treatment processes in removing different classes of emerging contaminants from domestic wastewater

● Different advanced treatment processes were tested for ECs removal from wastewater. ● UV radiation showed low to moderate removal for 5 of the 38 micropollutants. ● Among tested membrane processes, nanofiltration showed the better performance. ● The use of PAC achieved high or partially removal for 31 out of the 38 compounds. ● The environmental and economical evaluation of a pilot-scale PAC unit is suggested. In this work, 38 different organic emerging contaminants (ECs), belonging to various chemical classes such as pharmaceuticals (PhCs), endocrine-disrupting chemicals (EDCs), benzotriazoles (BTRs), benzothiazoles (BTHs), and perfluorinated compounds (PFCs), were initially identified and quantified in the biologically treated wastewater collected from Athens’ (Greece) Sewage Treatment Plant (STP). Processes already used in existing STPs such as microfiltration (MF), nanofiltration (NF), ultrafiltration (UF), UV radiation, and powdered activated carbon (PAC) were assessed for ECs’ removal, under the conditions that represent their actual application for disinfection or advanced wastewater treatment. The results indicated that MF removed only one out of the 38 ECs and hence it was selected as pretreatment step for the other processes. UV radiation in the studied conditions showed low to moderate removal for 5 out of the 38 ECs. NF showed better results than UF due to the smaller pore sizes of the filtration system. However, this enhancement was observed mainly for 8 compounds originating from the classes of PhCs and PFCs, while the removal of EDCs was not statistically significant. Among the various studied technologies, PAC stands out due to its capability to sufficiently remove most ECs. In particular, removal rates higher than 70% were observed for 9 compounds, 22 were partially removed, while 7 demonstrated low removal rates. Based on our screening experiments, future research should focus on scaling-up PAC in actual conditions, combining PAC with other processes, and conduct a complete economic and environmental assessment of the treatment.     

Construction of MOFs-based nanocomposite membranes for emerging organic contaminants abatement in water

● Application of the MOF-composite membranes in adsorption was discussed. ● Recent application of MOFs-membranes for separation was summarized. ● Separation and degradation for emerging organic contaminants were described. Presence of emerging organic contaminants (EOCs) in water is one of the major threats to water safety. In recent decades, an increasing number of studies have investigated new approaches for their effective removal. Among them, metal-organic frameworks (MOFs) have attracted increasing attention since their first development thanks to their tunable metal nodes and versatile, functional linkers. However, whether or not MOFs have a promising future for practical application in emerging contaminants-containing wastewater is debatable. This review summarizes recent studies about the removal of EOCs using MOFs-related material. The synthesis strategies of both MOF particles and composites, including thin-film nanocomposite and mixed matrix membranes, are critically reviewed, as well as various characterization technologies. The application of the MOF-based composite membranes in adsorption, separation (nanofiltration and ultrafiltration), and catalytic degradation are discussed. Overall, literature survey shows that MOFs-based composite could play a crucial role in eliminating EOCs in the future. In particular, modified membranes that realize separation and degradation might be the most promising materials for such application.     

Distribution,enrichment mechanism and risk assessment for fluoride in groundwater: a case study of Mihe-Weihe River Basin,China

● High fluorine is mainly HCO₃·Cl-Na and HCO₃-Na type. ● F⁻ decreases with the increase of depth to water table. ● High fluoride is mainly affected by fluorine-containing minerals and weak alkaline. ● Fluorine pollution is mainly in the north near Laizhou Bay (wet season > dry season). ● Groundwater samples have a high F⁻ health risk (children > adults). Due to the unclear distribution characteristics and causes of fluoride in groundwater of Mihe-Weihe River Basin (China), there is a higher risk for the future development and utilization of groundwater. Therefore, based on the systematic sampling and analysis, the distribution features and enrichment mechanism for fluoride in groundwater were studied by the graphic method, hydrogeochemical modeling, the proportionality factor between conventional ions and factor analysis. The results show that the fluorine content in groundwater is generally on the high side, with a large area of medium-fluorine water (0.5–1.0 mg/L), and high-fluorine water is chiefly in the interfluvial lowlands and alluvial-marine plain, which mainly contains HCO₃·Cl-Na- and HCO₃-Na-type water. The vertical zonation characteristics of the fluorine content decrease with increasing depth to the water table. The high flouride groundwater during the wet season is chiefly controlled by the weathering and dissolution of fluorine-containing minerals, as well as the influence of rock weathering, evaporation and concentration. The weak alkaline environment that is rich in sodium and poor in calcium during the dry season is the main reason for the enrichment of fluorine. Finally, an integrated assessment model is established using rough set theory and an improved matter element extension model, and the level of groundwater pollution caused by fluoride in the Mihe-Weihe River Basin during the wet and dry seasons in the Shandong Peninsula is defined to show the necessity for local management measures to reduce the potential risks caused by groundwater quality.     

Biodegradation of waste refrigerator polyurethane by mealworms

● Waste refrigerator polyurethane (WRPU) was ingested and biodegraded by mealworms. ● The carbon in WRPU-based frass was lower than that in WRPU. ● Urethane groups in WRPU were broken down after ingestion by mealworms. ● Thermal stability of WRPU-based frass were deteriorated compared to that of WRPU. ● Gut microbiomes of mealworms fed using WRPU were distinct from that fed using bran. Refrigerator insulation replacement results in discarding a large amount of waste refrigerator polyurethane (WRPU). Insect larvae like mealworms have been used to biodegrade pristine plastics. However, knowledge about mealworms degrading WRPU is scarce. This study presents an in-depth investigation of the degradation of WRPU by mealworms using the micro-morphology, composition, and functional groups of WRPU and the egested frass characteristics. It was found that the WRPU debris in frass was scoured, implying that WRPU was ingested and degraded by mealworms. The carbon content of WRPU-based frass was lower than that of WRPU, indicating that mealworms utilized WRPU as a carbon source. The urethane groups in WRPU were broken, and benzene rings’ C=C and C–H bonds in the isocyanate disappeared after being ingested by mealworms. Thermal gravimetric-differential thermal gravimetry analysis showed that the weight loss temperature of WRPU-based frass was 300 °C lower than that of WRPU, indicating that the thermal stability of WRPU deteriorated after being ingested. The carbon balance analysis confirmed that carbon in the ingested WRPU released as CO₂ increased from 18.84 % to 29.80 %, suggesting that WRPU was partially mineralized. The carbon in the mealworm biomass ingesting WRPU decreased. The possible reason is that WRPU does not supply sufficient nutrients for mealworm growth, and the impurities and odor present in WRPU affect the appetite of the mealworms. The microbial community analysis indicated that WRPU exerts a considerable effect on the gut microorganism of mealworms. These findings confirm that mealworms degrade WRPU.     

NiB2O4 (B = Mn or Co) catalysts for NH3-SCR of NOx at low-temperature in microwave field

● Microwave-assisted catalytic NH₃-SCR reaction over spinel oxides is carried out. ● SCR reaction temperature is tremendously lowered in microwave field. ● NO conversion of NiMn₂O₄ is highly up to 90.6% at 70°C under microwave heating. Microwave-assisted selective catalytic reduction of nitrogen oxides (NO_x) was investigated over Ni-based metal oxides. The NiMn₂O₄ and NiCo₂O₄ catalysts were synthesized by the co-precipitation method and their activities were evaluated as potential candidate catalysts for low-temperature NH₃-SCR in a microwave field. The physicochemical properties and structures of the catalysts were characterized by X-ray diffraction (XRD), Scanning electron microscope (SEM), N₂-physisorption, NO adsorption-desorption in the microwave field, H₂-temperature programmed reduction (H₂-TPR) and NH₃-temperature programmed desorption (NH₃-TPD). The results verified that microwave radiation reduced the reaction temperature required for NH₃-SCR compared to conventional heating, which needed less energy. For the NiMn₂O₄ catalyst, the catalytic efficiency exceeded 90% at 70 °C and reached 96.8% at 110 °C in the microwave field. Meanwhile, the NiMn₂O₄ also exhibited excellent low-temperature NH₃-SCR reaction performance under conventional heating conditions, which is due to the high BET specific surface area, more suitable redox property, good NO adsorption-desorption in the microwave field and rich acidic sites.     

Stress response to nanoplastics with different charges in Brassica napus L. during seed germination and seedling growth stages

● Higher concentrations of PS, PS-NH₂ and PS-SO₃H inhibited seed germination. ● PS, PS-NH₂ and PS-SO₃H influenced seedling growth in a dose-dependent manner. ● PS, PS-NH₂ and PS-SO₃H reduced essential nutrients uptake and plant quality. ● PS, PS-NH₂ and PS-SO₃H increased antioxidant enzyme activities and MDA content. ● Nanoplastic toxicity was related to surface charges. Nanoplastic pollution has become a significant problem in farmland systems worldwide. However, research on the effects of nanoplastics (NPs) with different charges on field crops is still limited. In our study, NPs with different charges, including unmodified polystyrene nanoplastics (PS), positively charged polystyrene nanoplastics (PS-NH₂), and negatively charged polystyrene nanoplastics (PS-SO₃H), were investigated for their impacts on seed germination and seedling growth of rape. The results showed that seed water uptake (after 12 h), seed germination, seed vigour, and relative root elongation were all significantly reduced under exposure to NPs (200 mg/L). Similarly, remarkable decreases in plant biomass (root weight, shoot weight), growth (root length, plant height), photosynthesis ability (chlorophyll a, chlorophyll b, carotenoids), essential nutrient uptake (Fe, Mn, Zn, Cu), and plant quality (soluble protein, soluble sugar, crude fibre content) of rape seedlings were also observed after exposure to NPs. Among the three kinds of NPs, PS-NH₂ showed stronger effects. Moreover, superoxide dismutase, peroxidase, and catalase activities of rape seedlings were changed, and the content of malondialdehyde was significantly increased under exposure to NPs. Furthermore, positively charged PS-NH₂ showed stronger effects on the phenotype, physiology, biochemistry, nutrient uptake, and plant quality of rape. Notably, a comprehensive toxicity evaluation revealed that PS-NH₂ had the strongest toxicity to rape. The present study provides important implications for the interaction and risk assessment of NPs and crops in soil-plant systems.     

Efficient production of hydrogen peroxide in microbial reverse-electrodialysis cells coupled with thermolytic solutions

● Appreciable H₂O₂ production rate was achieved in MRCs utilizing NH₄HCO₃ solutions. ● Carbon black outperformed activated carbon as the catalyst for H₂O₂ production. ● The optimum carbon black loading for H₂O₂ production on air-cathode was 10 mg/cm². ● The optimum number of cell pairs was determined to be three. ● A maximum power density of 980 mW/m² was produced by MRCs with 5 cell pairs. H₂O₂ was produced at an appreciable rate in microbial reverse-electrodialysis cells (MRCs) coupled with thermolytic solutions, which can simultaneously capture waste heat as electrical energy. To determine the optimal cathode and membrane stack configurations for H₂O₂ production, different catalysts, catalyst loadings and numbers of membrane cell pairs were tested. Carbon black (CB) outperformed activated carbon (AC) for H₂O₂ production, although AC showed higher catalytic activity for oxygen reduction. The optimum CB loading was 10 mg/cm² in terms of both the H₂O₂ production rate and power production. The optimum number of cell pairs was determined to be three based on a tradeoff between H₂O₂ production and capital costs. A H₂O₂ production rate as high as 0.99 ± 0.10 mmol/(L·h) was achieved with 10 mg/cm² CB loading and 3 cell pairs, where the H₂O₂ recovery efficiency was 52 ± 2% and the maximum power density was 780 ± 37 mW/m². Increasing the number of cell pairs to five resulted in an increase in maximum power density (980 ± 21 mW/m²) but showed limited effects on H₂O₂ production. These results indicated that MRCs can be an efficient method for sustainable H₂O₂ production.     

Effects of iron oxide nanoparticles on phenotype and metabolite changes in hemp clones (Cannabis sativa L.)

● Fe₃O₄ NPs increased the biomass and chlorophyll content of hemp clones. ● Fe₃O₄ NPs penetrated and were internalized by root cells. ● Fe₃O₄ NPs induced the alteration of metabolite profiles in hemp leaves. ● The psychoactive compound THC in hemp leaves was significantly down-regulated. We investigated the effect of iron oxide nanoparticles (Fe₃O₄ NPs, ~17 nm in size) on the phenotype and metabolite changes in hemp (Cannabis sativa L.), an annual crop distributed worldwide. Hemp clones were grown in hydroponic cultures with Fe₃O₄ NPs (50, 100, 200, or 500 mg/L) for four weeks. TEM and ICP-MS were used to determine Fe₃O₄ NPs uptake and translocation. LC-MS-based metabolomics was employed to explore the deep insight into the effect of Fe₃O₄ NPs on hemp plants. The results revealed that plant growth enhanced gradually with increasing concentrations of given NPs up to 200 mg/L, which improved the fresh weight and dry weight by 36.13% and 74.68%, respectively, compared to the control. Even at a high dose (500 mg/L), Fe₃O₄ NPs promoted plant growth, including increased biomass and tissue length. NPs significantly increased the iron and chlorophyll content in plant tissues Increased catalase activity and reduced hydrogen peroxide content in hemp leaves suggested that the Fe₃O₄ NPs activated the defense system. TEM showed that NPs were abundantly attached to the cell wall and dispersed throughout the root cells. Metabolomics revealed that Fe₃O₄ NPs induced metabolic reprogramming in hemp leaves, including the up-regulation of carbohydrates and organic acids, and down-regulation of antioxidants, especially tetrahydrocannabinol (THC). The significantly up-regulated metabolites, including peonidin and 2-hydroxycinnamic acid, could be involved in photosynthesis in hemp plants. These results demonstrate the potential of Fe₃O₄ NPs for promoting hemp growth and decreasing the THC content at low doses.     

Long-term exposure to air pollution and cerebrovascular disease: findings from Beijing Health Management Cohort study

● This study explored the long-term association by double robust additive models. ● Individual exposure concentrations were assessed by integrating GAM, LUR and BPNN. ● PM_2.5, SO₂ and NO₂ are positively associated with cerebrovascular disease. ● CO could reduce the risk of cerebrovascular disease with the highest robustness. ● The elderly, women and people with normal BMI are at higher risk for air pollution. The relationship between air pollution and cerebrovascular disease has become a popular topic, yet research findings are highly heterogeneous. This study aims to investigate this association based on detailed individual health data and a precise evaluation of their exposure levels. The integrated models of generalized additive model, land use regression model and back propagation neural network were used to evaluate the exposure concentrations. And doubly robust additive model was conducted to explore the association between cerebrovascular disease and air pollution after adjusted for demographic characteristics, physical examination, disease information, geographic and socioeconomic status. A total of 25097 subjects were included in the Beijing Health Management Cohort from 2013 to 2018. With a 1 μg/m³ increase in the concentrations of PM_2.5, SO₂ and NO₂, the incidence risk of cerebrovascular disease increased by 1.02 (95% CI: 1.008–1.034), 1.06 (95% CI: 1.034–1.095) and 1.02 (95% CI: 1.010–1.029) respectively. Whereas CO exposure could decrease the risk, with an odds ratio of 0.38 (95% CI: 0.212–0.626). In the subgroup analysis, individuals under the age of 50 with normal BMI were at higher risk caused by PM_2.5, and SO₂ was considered more hazardous to women. Meanwhile, the protective effect of CO on women and those with normal BMI was stronger. Successful reduction of long-term exposure to PM_2.5, SO₂ and NO₂ would lead to substantial benefits for decrease the risk of cerebrovascular disease especially for the health of the susceptible individuals.