Collaborative control of fine particles and ozone required in China for health benefit

● Increased DAAO offsets 3/4 of the decrease of DAAP in 2013–2020. ● DAAO increases are mainly due to O₃ concentration increase and population aging. ● Health benefit from PM_2.5 reduction after 2017 is larger than that before 2017. ● Reducing PM_2.5 concentration by 1% results in 0.6% reduction of DAAP. ● Reducing O₃ concentration by 1% results in 2% reduction of DAAO. PM_2.5 concentration declined significantly nationwide, while O₃ concentration increased in most regions in China in 2013–2020. Recent evidences proved that peak season O₃ is related to increased death risk from non-accidental and respiratory diseases. Based on these new evidences, we estimate excess deaths associated with long-term exposure to ambient PM_2.5 and O₃ in China following the counterfactual analytic framework from Global Burden Disease. Excess deaths from non-accidental diseases associated with long-term exposure to ambient O₃ in China reaches to 579 (95% confidential interval (CI): 93, 990) thousand in 2020, which has been significantly underestimated in previous studies. In addition, the increased excess deaths associated with long-term O₃ exposure (234 (95% CI: 177, 282) thousand) in 2013–2020 offset three quarters of the avoided excess deaths (302 (95% CI: 244, 366) thousand) mainly due to PM_2.5 exposure reduction. In key regions (the North China Plain, the Yangtze River Delta and the Fen-Wei Plain), the former is even larger than the latter, particularly in 2017–2020. Health benefit of PM_2.5 concentration reduction offsets the adverse effects of population growth and aging on excess deaths attributed to PM_2.5 exposure. Increase of excess deaths associated with O₃ exposure is mainly due to the strong increase of O₃ concentration, followed by population aging. Considering the faster population aging process in the future, collaborative control, and faster reduction of PM_2.5 and O₃ are needed to reduce the associated excess deaths.     

Simple fabrication of carboxymethyl cellulose and κ-carrageenan composite aerogel with efficient performance in removal of fluoroquinolone antibiotics from water

● A composite aerogel was simply obtained to remove various fluoroquinolones (FQs). ● The structural and textural properties of this composite aerogel are improved. ● Its adsorption capacity was improved at a low content of coexisting Cu²⁺ or Fe³⁺ ion. ● Two substructural analogs of FQs are compared to explore the adsorption mechanisms. ● This aerogel after saturated adsorption can be reused directly for Cu²⁺ adsorption. 3D composite aerogels (CMC-CG) composed of carboxymethyl cellulose and κ-carrageenan were designed and fabricated using the one-pot synthesis technique. The optimized CMC-CG showed a good mechanical property and a high swelling ratio due to its superior textural properties with a proper chemically cross-linked interpenetrating network structure. CMC-CG was utilized for the removal of various fluoroquinolones (FQs) from water and exhibited high adsorption performance because of effective electrostatic attraction and hydrogen bonding interactions. Ciprofloxacin (CIP), a popular FQ, was used as the representative. The optimized CMC-CG had a theoretically maximal CIP uptake of approximately 1.271 mmol/g at the pH of 5.0. The adsorption capacity of CMC-CG was improved in the presence of some cations, Cu²⁺ and Fe³⁺ ions, at a low concentration through the bridging effect but was reduced at a high concentration. The investigation of adsorption mechanisms, based on the adsorption kinetics, isotherms and thermodynamic study, Fourier transform infrared spectrometry and X-ray photoelectron spectroscopy analyses before and after adsorption, and changes in the adsorption performance of CMC-CG toward two molecular probes, further indicated that electrostatic attraction was the dominant interaction rather than hydrogen bonding in this adsorption. CMC-CG after saturated adsorption of CIP could be easily regenerated using a dilute NaCl aqueous solution and reused efficiently. Moreover, the disused aerogel could still be reused as a new adsorbent for effective adsorption of Cu²⁺ ion. Overall, this study suggested the promising applications of this composite aerogel as an eco-friendly, cost-effective, and recyclable adsorbent for the efficient removal of FQs from water.     

Catalytic urea hydrolysis by composite metal oxide catalyst towards efficient urea-based SCR process: performance evaluation and mechanism investigation

● Bimetallic oxide composite catalyst was designed for the urea-based SCR process. ● Surface chemical state and typical microstructure of catalyst was determined. ● Reaction route was improved based on intermediates and active site identification. ● TiO₂@Al₂O₃ presents an obvious promotion for urea hydrolysis. As a promising option to provide gaseous NH₃ for SCR system, catalytic urea hydrolysis has aroused great attention, and improving surface area and activity of catalysis are the crucial issues to be solved for efficient urea hydrolysis. Therefore, a composite metal oxide (TiO₂@Al₂O₃) catalyst was prepared by a simple hydrothermal method, with mesoporous alumina (γ-Al₂O₃) as substrate. The results verify the mesoporous structure and submicron cluster of TiO₂@Al₂O₃, with exposed crystal faces of (101) and (400) for TiO₂ and γ-Al₂O₃, respectively. The electronegativity difference of Ti⁴⁺ and Al³⁺ changes the charge distribution scheme around the interface, which provides abundant acid/base sites to boost the urea hydrolysis. Consequently, for an optimal proportioning with nano TiO₂ content at 10 wt.%, the hydrolysis efficiency can reach up to 35.2 % at 100 °C in 2 h, increasing by ~7.1 % than that of the blank experiment. ¹³C NMR spectrum measurements provide the impossible intermediate species during urea hydrolysis. Theoretical calculations are performed to clarify the efficient H₂O decomposition at the interface of TiO₂@Al₂O₃. The result offers a favorable technology for energy-efficiency urea hydrolysis.     

Legacies and health risks of heavy metals,polybrominated diphenyl ethers,and polychlorinated dibenzo-dioxins/furans at e-waste recycling sites in South China

● Heavy metals and organic toxins may persist in legacy sites for a long time. ● Contaminants pose potential harms to the nearby community (HI > 1). ● PCDD/Fs had the risk of endocrine disruption and reproductive risk. ● Further intervention is needed to reduce pollution and related risks. Informal electronic-waste (e-waste) recycling sites pose substantial health risks to surrounding environments and populations, yet they are not properly regulated. In this study, the soil levels of copper, lead, cadmium, eight polybrominated diphenyl ethers (PBDEs), and 18 polychlorinated dibenzo-dioxins/furans (PCDD/Fs) were measured at two e-waste recycling sites in South China between 2014 and 2019. Both sites have been abandoned for natural restoration. Our results indicate that the mean Cd and PCDD/F levels at Site A in 2019 were higher than those recommended by current safety guidelines. Meanwhile, the highest exposure among children was 1.36 × 10⁻² mg/(kg·d) for Cu, followed by 5.05 × 10⁻³ mg/(kg·d) for Pb, 9.71 ng/(kg·d) for PBDEs, and 6.82 ng TEQ/(kg·d) for PCDD/Fs. Children were at elevated risk for health problem posed by Pb and Cu exposure at both sites (hazard quotient > 1) and by PCDD/Fs at Site A. Further risk assessment was conducted on the target organs and endpoints of heavy metals and PCDD/Fs. The hazard index (HI) for the target organ mixed-risk of heavy metals was high (HI = 1.27), as was that of PCDD/Fs (HI = 1.66), which can disrupt endocrine function and pose a risk of reproductive toxicity in children. Owing to incomplete cleaning, contaminants persist in soils over long periods and may harm nearby environments and communities. Our study demonstrates that heavy metal, PBDE, and PCDD/F contamination have not yet been remediated, and intervention is needed to reduce pollution and associated risks in areas affected by e-waste.     

Control strategies for disinfection byproducts by ion exchange resin,nanofiltration and their sequential combination

● Effects of AER adsorption and NF on DBP precursors, DBPs, and TOX were examined. ● A treatment approach of resin adsorption followed by nanofiltration was developed. ● Both DOC and Br⁻ could be effectively removed by the sequential approach. ● DBPs, TOX, and cytotoxicity were significantly reduced by the sequential approach. Disinfection byproducts (DBPs) are emerging pollutants in drinking water with high health risks. Precursor reduction before disinfection is an effective strategy to control the formation of DBPs. In this study, three types of anion exchange resins (AERs) and two types of nanofiltration (NF) membranes were tested for their control effects on DBP precursors, DBPs, and total organic halogen (TOX). The results showed that, for AER adsorption, the removal efficiencies of DBP precursors, DBPs, and TOX increased with the increase of resin dose, and the strong basic macroporous anion exchange resin (M500MB) had the highest removal efficiencies. For NF, the highest removal efficiencies were achieved at an operating pressure of 4 bar, and the membrane (NF90) with a smaller molecular weight cut-off, had a better control efficiency. However, AER adsorption was inefficient in removing dissolved organic carbon (DOC); NF was inefficient in removing Br⁻ resulting in insufficient control of Br-DBPs. Accordingly, a sequential approach of AER (M500MB) adsorption followed by NF (NF90) was developed to enhance the control efficiency of DBPs. Compared with single AER adsorption and single NF, the sequential approach further increased the removal efficiencies of DOC by 19.4%–101.9%, coupled with the high Br⁻ removal efficiency of 92%, and thus improved the reduction of cyclic DBPs and TOX by 3.5%–4.9%, and 2.4%–8.4%, respectively; the sequential approach also reduced the cytotoxicity of the water sample by 66.4%.     

Preparation of nZVI embedded modified mesoporous carbon for catalytic persulfate to degradation of reactive black 5

• The MCNZVI is prepared as an interesting material for PS activation. • Graphitized carbon shells facilitate electron transfer from Fe⁰. • The MCNZVI exhibits excellent performance to degrade RB5 by ¹O₂. • The MCNZVI has high stability and reusability in the oxidation system. High-efficiency and cost-effective catalysts with available strategies for persulfate (PS) activation are critical for the complete mineralization of organic contaminants in the environmental remediation and protection fields. A nanoscale zero-valent iron-embedded modified mesoporous carbon (MCNZVI) with a core-shell structure is synthesized using the hydrothermal synthesis method and high-temperature pyrolysis. The results showed that nZVI could be impregnated within mesoporous carbon frameworks with a comparatively high graphitization degree, rich nitrogen doping content, and a large surface area and pore volume. This material was used as a persulfate activator for the oxidation removal of Reactive Black 5 (RB5). The effects of the material dosage, PS concentration, pH, and some inorganic anions (i.e., Cl⁻, SO₄²⁻) on RB5 degradation were then investigated. The highest degradation efficiency (97.3%) of RB5 was achieved via PS (20 mmol/L) activation by the MCNZVI (0.5 g/L). The pseudo-first-order kinetics (k = 2.11 × 10⁻² min⁻¹) in the MCNZVI/PS (0.5 g/L, 20 mmol/L) was greater than 100 times than that in the MCNZVI and PS. The reactive oxygen species (ROS), including ¹O₂, SO₄^·−, HO^·, and ·O₂⁻, were generated by PS activation with the MCNZVI. Singlet oxygen was demonstrated to be the primary ROS responsible for the RB5 degradation. The MCNZVI could be reused and regenerated for recycling. This work provides new insights into PS activation to remove organic contamination.     

Adsorption of herring sperm DNA onto pine sawdust biochar: Thermodynamics and site energy distribution

● Adsorption of environmental deoxyribonucleic acid on biochar was studied. ● π−π interaction and electrostatic repulsion worked in the adsorption. ● Thermodynamics indicated the adsorption was spontaneous and endothermic. Environmental deoxyribonucleic acid (eDNA), which includes antibiotic resistance genes, is ubiquitous in the environment. The interactions between eDNA and biochar, a promising material widely used in soil amendment and water treatment, greatly affect the environmental behavior of eDNA. Hitherto few experimental evidences are available yet, especially on the information of thermodynamics and energy distribution to explains the interactions between biochar and eDNA. This study investigated the adsorption of herring sperm DNA (hsDNA) on pine sawdust biochar, with a specific emphasis on the adsorption thermodynamics and site energy distribution. The adsorption of hsDNA on biochar was enhanced by an increase in the pyrolysis and adsorption temperatures. The higher surface area, stronger π−π interaction, and weaker electrostatic repulsion between hsDNA and biochars prepared at high pyrolysis temperatures facilitated the adsorption of hsDNA. The thermodynamics indicated that the adsorption of hsDNA on biochar was spontaneous and endothermic. Therefore, higher temperature was beneficial for the adsorption of hsDNA on biochar; this was well explained by the increase in E^* and F(E^*) with the adsorption temperature. These results are useful for evaluating the migration and transformation of eDNA in the presence of biochar.     

Enhanced activation of peroxymonosulfate by CNT-TiO2 under UV-light assistance for efficient degradation of organic pollutants

CNT-TiO₂ composite is used to activate PMS under UV-light assistance. Superior performance is due to the enhanced electron-transfer ability of CNT. SO₄•⁻, •OH and ¹O₂ play key roles in the degradation of organic pollutants. In this work, a UV-light assisted peroxymonosulfate (PMS) activation system was constructed with the composite catalyst of multi-walled carbon nanotubes (CNT) - titanium dioxide (TiO₂). Under the UV light irradiation, the photoinduced electrons generated from TiO₂ could be continuously transferred to CNT for the activation of PMS to improve the catalytic performance of organic pollutant degradation. Meanwhile, the separation of photoinduced electron-hole pairs could enhance the photocatalysis efficiency. The electron spin resonance spectroscopy (EPR) and quenching experiments confirmed the generation of sulfate radical (SO₄•⁻), hydroxyl radical (•OH) and singlet oxygen (¹O₂) in the UV/PMS/20%CNT-TiO₂ system. Almost 100% phenol degradation was observed within 20 min UV-light irradiation. The kinetic reaction rate constant of the UV/PMS/20%CNT-TiO₂ system (0.18 min⁻¹) was 23.7 times higher than that of the PMS/Co₃O₄ system (0.0076 min⁻¹). This higher catalytic performance was ascribed to the introduction of photoinduced electrons, which could enhance the activation of PMS by the transfer of electrons in the UV/PMS/CNT-TiO₂ system.     

Effect of Cu-ZSM-5 catalysts with different CuO particle size on selective catalytic oxidation of N,N-Dimethylformamide

● A series of Cu-ZSM-5 catalysts were tested for DMF selective catalytic oxidation. ● Cu-6 nm samples showed the best catalytic activity and N₂ selectivity. ● Redox properties and chemisorbed oxygen impact on DMF catalytic oxidation. ● Isolated Cu²⁺ species and weak acidity have effects on the generation of N₂. N, N-Dimethylformamide (DMF), a nitrogen-containing volatile organic compound (NVOC) with high emissions from the spray industry, has attracted increasing attention. In this study, Cu-ZSM-5 catalysts with different CuO particle sizes of 3, 6, 9 and 12 nm were synthesized and tested for DMF selective catalytic oxidation. The crystal structure and physicochemical properties of the catalyst were studied by various characterization methods. The catalytic activity increases with increasing CuO particle size, and complete conversion can be achieved at 300–350 °C. The Cu-12 nm catalyst has the highest catalytic activity and can achieve complete conversion at 300 °C. The Cu-6 nm sample has the highest N₂ selectivity at lower temperatures, reaching 95% at 300 °C. The activity of the catalysts is determined by the surface CuO cluster species, the bulk CuO species and the chemisorbed surface oxygen species. The high N₂ selectivity of the catalyst is attributed to the ratio of isolated Cu²⁺ and bulk CuO species, and weak acidity is beneficial to the formation of N₂. The results in this work will provide a new design of NVOC catalytic oxidation catalysts.     

Bacteria inactivation by sulfate radical: progress and non-negligible disinfection by-products

● Status of inactivation of pathogenic microorganisms by SO₄^•− is reviewed. ● Mechanism of SO₄^•− disinfection is outlined. ● Possible generation of DBPs during disinfection using SO₄^•− is discussed. ● Possible problems and challenges of using SO₄^•− for disinfection are presented. Sulfate radicals have been increasingly used for the pathogen inactivation due to their strong redox ability and high selectivity for electron-rich species in the last decade. The application of sulfate radicals in water disinfection has become a very promising technology. However, there is currently a lack of reviews of sulfate radicals inactivated pathogenic microorganisms. At the same time, less attention has been paid to disinfection by-products produced by the use of sulfate radicals to inactivate microorganisms. This paper begins with a brief overview of sulfate radicals’ properties. Then, the progress in water disinfection by sulfate radicals is summarized. The mechanism and inactivation kinetics of inactivating microorganisms are briefly described. After that, the disinfection by-products produced by reactions of sulfate radicals with chlorine, bromine, iodide ions and organic halogens in water are also discussed. In response to these possible challenges, this article concludes with some specific solutions and future research directions.     

Mechanistic insights into the selective photocatalytic degradation of dyes over TiO2/ZSM-11

● TiO₂/ZSM-11 was prepared by a facile solid state dispersion method. ● Mechanism for photocatalytic degradation of dyes was investigated. ● Both experimental and MD simulations were conducted. ● Chemisorption instead of electrostatic interaction played a critical role. Photocatalytic degradation is a promising way to eliminate dye contaminants. In this work, a series of TiO₂/ZSM-11 (TZ) nanocomposites were prepared using a facile solid state dispersion method. Methyl orange (MO), methylene blue (MB), and rhodamine B (RhB) were intentionally chosen as target substrates in the photocatalytic degradation reactions. Compared to pristine TiO₂, negative effect was observed on MO degradation while promoted kinetics were collected on MB and RhB over TZ composites. Moreover, a much higher photocatalytic rate was interestingly achieved on RhB than MB, which indicated that a new factor has to be included other than the widely accepted electrostatic interaction mechanism to fully understand the selective photodegradation reactions. Systematic characterizations showed that TiO₂ and ZSM-11 physically mixed and maintained both the whole framework and local structure without chemical interaction. The different trends observed in surface area and the photo-absorption ability of TZ composites with reaction performance further excluded both as the promotion mechanism. Instead, adsorption energies predicted by molecular dynamics simulations suggested that differences in the adsorption strength played a critical role. This work provided a deep mechanistic understanding of the selective photocatalytic degradation of dyes reactions, which helps to rationally design highly efficient photocatalysts.     

Removal of ammonium and nitrate through Anammox and FeS-driven autotrophic denitrification

● Simultaneous NH₄⁺/NO₃^– removal was achieved in the FeS denitrification system ● Anammox coupled FeS denitrification was responsible for NH₄⁺/NO₃^– removal ● Sulfammox, Feammox and Anammox occurred for NH₄⁺ removal ● Thiobacillus, Nitrospira , and Ca. Kuenenia were key functional microorganisms An autotrophic denitrifying bioreactor with iron sulfide (FeS) as the electron donor was operated to remove ammonium (NH₄⁺) and nitrate (NO₃⁻) synergistically from wastewater for more than 298 d. The concentration of FeS greatly affected the removal of NH₄⁺/NO₃⁻. Additionally, a low hydraulic retention time worsened the removal efficiency of NH₄⁺/NO₃⁻. When the hydraulic retention time was 12 h, the optimal removal was achieved with NH₄⁺ and NO₃⁻ removal percentages both above 88%, and the corresponding nitrogen removal loading rates of NH₄⁺ and NO₃⁻ were 49.1 and 44.0 mg/(L·d), respectively. The removal of NH₄⁺ mainly occurred in the bottom section of the bioreactor through sulfate/ferric reducing anaerobic ammonium oxidation (Sulfammox/Feammox), nitrification, and anaerobic ammonium oxidation (Anammox) by functional microbes such as Nitrospira, Nitrosomonas, and Candidatus Kuenenia. Meanwhile, NO₃⁻ was mainly removed in the middle and upper sections of the bioreactor through autotrophic denitrification by Ferritrophicum, Thiobacillus, Rhodanobacter, and Pseudomonas, which possessed complete denitrification-related genes with high relative abundances.     

Property-performance relationship of core-shell structured black TiO2 photocatalyst for environmental remediation

● Properties and performance relationship of CSBT photocatalyst were investigated. ● Properties of CSBT were controlled by simply manipulating glycerol content. ● Performance was linked to semiconducting and physicochemical properties. ● CSBT (W:G ratio 9:1) had better performance with lower energy consumption. ● Phenols were reduced by 48.30% at a cost of $2.4127 per unit volume of effluent. Understanding the relationship between the properties and performance of black titanium dioxide with core-shell structure (CSBT) for environmental remediation is crucial for improving its prospects in practical applications. In this study, CSBT was synthesized using a glycerol-assisted sol-gel approach. The effect of different water-to-glycerol ratios (W:G = 1:0, 9:1, 2:1, and 1:1) on the semiconducting and physicochemical properties of CSBT was investigated. The effectiveness of CSBT in removing phenolic compounds (PHCs) from real agro-industrial wastewater was studied. The CSBT synthesized with a W:G ratio of 9:1 has optimized properties for enhanced removal of PHCs. It has a distinct core-shell structure and an appropriate amount of Ti³⁺ cations (11.18%), which play a crucial role in enhancing the performance of CSBT. When exposed to visible light, the CSBT performed better: 48.30% of PHCs were removed after 180 min, compared to only 21.95% for TiO₂ without core-shell structure. The CSBT consumed only 45.5235 kWh/m³ of electrical energy per order of magnitude and cost $2.4127 per unit volume of treated agro-industrial wastewater. Under the conditions tested, the CSBT demonstrated exceptional stability and reusability. The CSBT showed promising results in the treatment of phenols-containing agro-industrial wastewater.     

Catalytic reduction of water pollutants: knowledge gaps,lessons learned,and new opportunities

● Advances, challenges, and opportunities for catalytic water pollutant reduction. ● Cases of Pd-based catalysts for nitrate, chlorate, and perchlorate reduction. ● New functionalities developed by screening and design of catalytic metal sites. ● Facile catalyst preparation approaches for convenient catalyst optimization. ● Rational design and non-decorative effort are essential for future work. In this paper, we discuss the previous advances, current challenges, and future opportunities for the research of catalytic reduction of water pollutants. We present five case studies on the development of palladium-based catalysts for nitrate, chlorate, and perchlorate reduction with hydrogen gas under ambient conditions. We emphasize the realization of new functionalities through the screening and design of catalytic metal sites, including (i) platinum group metal (PGM) nanoparticles, (ii) the secondary metals for improving the reaction rate and product selectivity of nitrate reduction, (iii) oxygen-atom-transfer metal oxides for chlorate and perchlorate reduction, and (iv) ligand-enhanced coordination complexes for substantial activity enhancement. We also highlight the facile catalyst preparation approach that brought significant convenience to catalyst optimization. Based on our own studies, we then discuss directions of the catalyst research effort that are not immediately necessary or desirable, including (1) systematic study on the downstream aspects of under-developed catalysts, (2) random integration with hot concepts without a clear rationale, and (3) excessive and decorative experiments. We further address some general concerns regarding using H₂ and PGMs in the catalytic system. Finally, we recommend future catalyst development in both “fundamental” and “applied” aspects. The purpose of this perspective is to remove major misconceptions about reductive catalysis research and bring back significant innovations for both scientific advancements and engineering applications to benefit environmental protection.     

Oxidation and biotoxicity assessment of microcystin-LR using different AOPs based on UV,O3 and H2O2

MC-LR removal performances under different AOPs were compared systematically. Higher removal efficiency and synergistic effects were obtained by combined process. The acute biotoxicity raised in different degrees after oxidation. Microcystin-LR attracts attention due to its high toxicity, high concentration and high frequency. The removal characteristics of UV/H₂O₂ and O₃/H₂O₂ advanced oxidation processes and their individual process for MC-LR were investigated and compared in this study. Both the removal efficiencies and rates of MC-LR as well as the biotoxicity of degradation products was analyzed. Results showed that the UV/H₂O₂ process and O₃/H₂O₂ were effective methods to remove MC-LR from water, and they two performed better than UV-, O₃-, H₂O₂-alone processes under the same conditions. The effects of UV intensity, H₂O₂ concentration and O₃ concentration on the removal performance were explored. The synergistic effects between UV and H₂O₂, O₃ and H₂O₂ were observed. UV dosage of 1800 mJ·cm⁻² was required to remove 90% of 100 mg·L⁻¹ MC-LR, which amount significantly decreased to 500 mJ·cm⁻² when 1.7 mg·L⁻¹ H₂O₂ was added. 0.25 mg·L⁻¹ O₃, or 0.125 mg·L⁻¹ O₃ with 1.7 mg·L⁻¹ H₂O₂ was needed to reach 90% removal efficiency. Furthermore, the biotoxicity results about these UV/H₂O₂, O₃/H₂O₂ and O₃-alone processes all present rising trends with oxidation degree of MC-LR. Biotoxicity of solution, equivalent to 0.01 mg·L⁻¹ Zn²⁺, raised to 0.05 mg·L⁻¹ Zn²⁺ after UV/H₂O₂ or O₃/H₂O₂ reaction. This phenomenon may be attributed to the aldehydes and ketones with small molecular weight generated during reaction. Advice about the selection of MC-LR removal methods in real cases was provided.     

Electro-conductive crosslinked polyaniline/carbon nanotube nanofiltration membrane for electro-enhanced removal of bisphenol A

● A crosslinked polyaniline/carbon nanotube NF membrane was fabricated. ● Electro-assistance enhanced the removal rate of the NF membrane for bisphenol A. ● Intermittent voltage-assistance can achieve nearly 100% removal of bisphenol A. ● Membrane adsorption–electro-oxidation process is feasible for micropollutant removal. Nanofiltration (NF) has attracted increasing attention for wastewater treatment and potable water purification. However, the high-efficiency removal of micropollutants by NF membranes is a critical challenge. Owing to the adsorption and subsequent diffusion, some weakly charged or uncharged micropollutants, such as bisphenol A (BPA), can pass through NF membranes, resulting in low removal rates. Herein, an effective strategy is proposed to enhance the BPA removal efficiency of a crosslinked polyaniline/carbon nanotube NF membrane by coupling the membrane with electro-assistance. The membrane exhibited a 31.9% removal rate for 5 mg/L BPA with a permeance of 6.8 L/(m²·h·bar), while the removal rate was significantly improved to 98.1% after applying a voltage of 2.0 V to the membrane. Furthermore, when BPA coexisted with humic acid, the membrane maintained 94% removal of total organic carbon and nearly 100% removal of BPA at 2.0 V over the entire filtration period. Compared to continuous voltage applied to the membrane, an intermittent voltage (2.0 V for 0.5 h with an interval of 3.5 h) could achieve comparable BPA removal efficiency, because of the combined effect of membrane adsorption and subsequent electrochemical oxidation. Density functional theory calculations and BPA oxidation process analyses suggested that BPA was adsorbed by two main interactions: π–π and hydrogen-bond interactions. The adsorbed BPA was further electro-degraded into small organic acids or mineralized to CO₂ and H₂O. This work demonstrates that NF membranes coupled with electro-assistance are feasible for improving the removal of weakly charged or uncharged micropollutants.     

PM2.5 concentration declining saves health expenditure in China

● Monthly hospitalization expenses are sensitive to increases in PM_2.5 exposure. ● The increased PM_2.5 causes patients with CHD and LRI to stay longer in the hospital. ● The impact of PM_2.5 on total expenses for stroke is greater in southern China. ● Males may be more sensitive to air pollution than females. Air pollution has been a severe issue in China. Exposure to PM_2.5 has adverse health effects and causes economic losses. This study investigated the economic impact of exposure to PM_2.5 pollution using monthly city-level data covering 88.5 million urban employees in 2016 and 2017. This study mainly focused on three expenditure indicators to measure the economic impact considering lower respiratory infections (LRIs), coronary heart disease (CHD), and stroke. The results show that a 10 µg/m³ increase in PM_2.5 would cause total monthly expenses of LRIs, CHD, and stroke to increase by 0.226%, 0.237%, and 0.374%, respectively. We also found that LRI, CHD, and stroke hospital admissions increased significantly by 10%, 8.42%, and 5.64%, respectively. Furthermore, the total hospital stays of LRIs, CHDs, and strokes increased by 2.49%, 2. 51%, and 1.64%, respectively. Our findings also suggest heterogeneous impacts of PM_2.5 exposures by sex and across regions, but no statistical evidence shows significant differences between the older and younger adult subgroups. Our results provide several policy implications for reducing unequal public health expenditures in overpolluted countries.     

Electrocatalytic biofilm reactor for effective and energy-efficient azo dye degradation: the synergistic effect of MnOx/Ti flow-through anode and biofilm on the cathode

● MnO _x /Ti flow-through anode was coupled with the biofilm-attached cathode in ECBR. ● ECBR was able to enhance the azo dye removal and reduce the energy consumption. ● Mn^IV=O generated on the electrified MnO _x /Ti anode catalyzed the azo dye oxidation. ● Aerobic heterotrophic bacteria on the cathode degraded azo dye intermediate products. ● Biodegradation of intermediate products was stimulated under the electric field. Dyeing wastewater treatment remains a challenge. Although effective, the in-series process using electrochemical oxidation as the pre- or post-treatment of biodegradation is long. This study proposes a compact dual-chamber electrocatalytic biofilm reactor (ECBR) to complete azo dye decolorization and mineralization in a single unit via anodic oxidation on a MnO_x/Ti flow-through anode followed by cathodic biodegradation on carbon felts. Compared with the electrocatalytic reactor with a stainless-steel cathode (ECR-SS) and the biofilm reactor (BR), the ECBR increased the chemical oxygen demand (COD) removal efficiency by 24 % and 31 % (600 mg/L Acid Orange 7 as the feed, current of 6 mA), respectively. The COD removal efficiency of the ECBR was even higher than the sum of those of ECR-SS and BR. The ECBR also reduced the energy consumption (3.07 kWh/kg COD) by approximately half compared with ECR-SS. The advantages of the ECBR in azo dye removal were attributed to the synergistic effect of the MnO_x/Ti flow-through anode and cathodic biofilms. Catalyzed by Mn^IV=O generated on the MnO_x/Ti anode under a low applied current, azo dyes were oxidized and decolored. The intermediate products with improved biodegradability were further mineralized by the cathodic aerobic heterotrophic bacteria (non-electrochemically active) under the stimulation of the applied current. Taking advantage of the mutual interactions among the electricity, anode, and bacteria, this study provides a novel and compact process for the effective and energy-efficient treatment of azo dye wastewater.     

Penicillin fermentation residue biochar as a high-performance electrode for membrane capacitive deionization

● We have provided an activated method to remove the toxicity of antibiotic residue. ● PFRB can greatly improve the salt adsorption capacity of MCDI. ● The hierarchical porous and abundant O/N-doped played the key role for the high-capacity desalination. ● A new field of reuse of penicillin fermentation residue has been developed. Membrane capacitive deionization (MCDI) is an efficient desalination technology for brine. Penicillin fermentation residue biochar (PFRB) possesses a hierarchical porous and O/N-doped structure which could serve as a high-capacity desalination electrode in the MCDI system. Under optimal conditions (electrode weight, voltage, and concentration) and a carbonization temperature of 700 °C, the maximum salt adsorption capacity of the electrode can reach 26.4 mg/g, which is higher than that of most carbon electrodes. Furthermore, the electrochemical properties of the PFRB electrode were characterized through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) with a maximum specific capacitance of 212.18 F/g. Finally, biotoxicity tests have showed that PFRB was non-biotoxin against luminescent bacteria and the MCDI system with the PFRB electrode remained stable even after 27 adsorption–desorption cycles. This study provides a novel way to recycle penicillin residue and an electrode that can achieve excellent desalination.