Prediction of mass and momentum transport in turbulent plane wall jets over smooth and transitionally rough surfaces

This paper is concerned with the prediction of mass and momentum transport in turbulent wall jets developing over smooth and transitionally rough plane walls. The ability to accurately predict the resulting wall shear stresses and vertical profiles of the Reynolds stresses in these flows is prerequisite to the accurate prediction of bed scour, sediment re-suspension and transport by turbulent diffusion. The computations were performed by solving the Reynolds-averaged forms of the equations describing conservation of mass, momentum and concentration. The unknown correlations that arise from the averaging process (the Reynolds stresses in the case of the momentum equation, and the turbulent mass fluxes in the case of concentration) were obtained from the solution of modeled differential equations that describe their conservation. Since these models are somewhat more complex than those typically used in practice, their benefits are demonstrated by comparisons with results obtained from simpler, eddy-viscosity based closures. Comparisons with experimental data show that results of acceptable accuracy can be obtained only by using the appropriate combination of models for the turbulent fluxes of mass and momentum that properly account for the reduction of the Reynolds stresses due to wall damping effects, and for the modification of the mass transfer rates due to interactions with the mean rates of strain.     

Froude scaling limitations in modeling of turbidity currents

The scaling problem associated with the modeling of turbidity currents has been recognized but is yet to be explored systematically. This paper presents an analysis of the dimensionless governing equations of turbidity currents to investigate the scale effect. Three types of flow conditions are considered: (i) conservative density current; (ii) purely depositional turbidity current; and (iii) mixed erosional/depositional turbidity current. Two controlling dimensionless numbers, the Froude number and the Reynolds number, appear in the non-dimensional governing equations. When densimetric Froude similarity is satisfied, the analysis shows that the results would be scale-invariant for conservative density current under the rough turbulent condition. In the case of purely depositional flows, truly scale-invariant results cannot be obtained, as the Reynolds-mediated scale effects appear in the bottom boundary conditions of the flow velocity and sediment fall velocity. However, the scale effect would be relatively modest. The Reynolds effect becomes more significant for erosional or mixed erosional/depositional turbidity currents as Reynolds-mediated scale effects also appear in the sediment entrainment relation. Numerical simulations have been conducted at three different scales by considering densimetric Froude scaling alone as well as combined densimetric Froude and Reynolds similarity. Simulation results confirm that although the scaling of densimetric Froude number alone can produce scale-invariable results for conservative density currents, variations occur in the case of turbidity currents. The results become scale invariant when densimetric Froude and Reynolds similarities are satisfied simultaneously.     

Experimental Study of the Criteria of Flow Laminarization in Two-Dimensional Dense Gas Plumes

Laminarization of flow in a two-dimensional dense gas plume was experimentally investigated in this study. The plume was created by releasing CO₂ through a ground-level line source into a simulated turbulent boundary layer over an aerodynamically rough surface in a meteorological wind tunnel. The bulk Richardson number (Ri_*), based on negative plume buoyancy, plume thickness, and friction velocity, was varied over a wide range so that the effects of stable stratification on plume laminarization could be observed. A variety of ambient wind speeds as well as three different sizes of roughness arrays were used so that possible effects of roughness Reynolds number (Re_*) on plume laminarization could also be identified. Both flow visualization methods and quantitative measurements of velocity and intermittency of turbulence were used to provide quantitative assessments of plume laminarization.Flow visualization provided an overall picture of how the plume was affected by the negative buoyancy. With increasing Ri_*, both the plume depth and the vertical mixing were significantly suppressed, while upstream propagation of the plume from the source was enhanced. The most important feature of the flow revealed by visualization was the laminarization of flow in the lower part of the plume, which appeared to be closely related to both Ri_* and Re_*.Measurements within the simulated dense gas plumes revealed the influence of the stable stratification on mean velocity and turbulence intensity profiles. Both the mean velocity and turbulence intensity were significantly reduced near the surface; and these reductions systematically depended on Ri_*. The roughness Reynolds number also had considerable influence on the mean flow and turbulence structure of the dense gas plumes.An intermittency analysis technique was developed and applied to the digitized instantaneous velocity signals. It not only confirmed the general flow picture within the dense plume indicated by the flow visualization, but also clearly demonstrated the changes of flow regime with variations in Ri_* and Re_*. Most importantly, based on this intermittency analysis, simple criteria for characterizing different flow regimes are formulated; these may be useful in predicting when plume laminarization might occur.     

Turbulent secondary flows in wall turbulence: vortex forcing,scaling arguments,and similarity solution

Spanwise surface heterogeneity beneath high-Reynolds number, fully-rough wall turbulence is known to induce a mean secondary flow in the form of counter-rotating streamwise vortices—this arrangement is prevalent, for example, in open-channel flows relevant to hydraulic engineering. These counter-rotating vortices flank regions of predominant excess(deficit) in mean streamwise velocity and downwelling(upwelling) in mean vertical velocity. The secondary flows have been definitively attributed to the lower surface conditions, and are now known to be a manifestation of Prandtl’s secondary flow of the second kind—driven and sustained by spatial heterogeneity of components of the turbulent (Reynolds averaged) stress tensor (Anderson et al. J Fluid Mech 768:316–347, 2015). The spacing between adjacent surface heterogeneities serves as a control on the spatial extent of the counter-rotating cells, while their intensity is controlled by the spanwise gradient in imposed drag (where larger gradients associated with more dramatic transitions in roughness induce stronger cells). In this work, we have performed an order of magnitude analysis of the mean (Reynolds averaged) transport equation for streamwise vorticity, which has revealed the scaling dependence of streamwise circulation intensity upon characteristics of the problem. The scaling arguments are supported by a recent numerical parametric study on the effect of spacing. Then, we demonstrate that mean streamwise velocity can be predicted a priori via a similarity solution to the mean streamwise vorticity transport equation. A vortex forcing term has been used to represent the effects of spanwise topographic heterogeneity within the flow. Efficacy of the vortex forcing term was established with a series of large-eddy simulation cases wherein vortex forcing model parameters were altered to capture different values of spanwise spacing, all of which demonstrate that the model can impose the effects of spanwise topographic heterogeneity (absent the need to actually model roughness elements); these results also justify use of the vortex forcing model in the similarity solution.     

Near-boundary velocity and turbulence in depth-varying stream flows

This research examined the temporal distribution of turbulent structure near a streambank toe through the progression of a flood wave in West Run (Morgantown, WV, USA). Three-dimensional velocities and water depths were measured through a 17-h flood event. Turbulence characteristics were examined: Reynolds stresses, turbulent kinetic energy, and turbulence intensities. On average, near-boundary velocity during the rising stage was less than the falling stage, likely due to the measurement location and local roughness. The velocity vectors shifted from towards bed before the flood wave to toward the streambank during progression of the flood wave. Turbulent kinetic energy increased with increasing water depth during the rising stage. Reynolds stress, τ_xz, increased with increasing water depth during the rising stage, but the majority of the stresses were negative through the storm event. Reynolds stress, τ_xy, was positive throughout the event and did not vary with depth. This work is among the first to evaluate turbulence during depth-varying flows in the field.     

Passive scalar roughness lengths for atmospheric boundary layer flow over complex, fractal topographies

When modeling atmospheric boundary layer flow over rough landscapes, surface fluxes of flow quantities (momentum, temperature, etc.) can be described with equilibrium logarithmic law expressions, all of which require specification of a roughness length that is, physically, the elevation at which the flow quantity equals its surface value. In high Reynolds number flows, such as the atmospheric boundary layer, inertial forces associated with turbulent eddy motions are responsible for surface momentum fluxes (form, or pressure drag). Surface scalar fluxes, on the other hand, occur exclusively via diffusion in the immediate vicinity of the topography—the interfacial region—before being advected by turbulent eddy motions into the bulk of the flow. Owing to this difference in surface transfer mechanism, the passive scalar roughness length, $z_{0S}$ , is known to be less than the momentum roughness length, $z_0$ . In this work, classical relations are used to specify $z_{0S}$ during large-eddy simulation of atmospheric boundary layer flow over aerodynamically rough, synthetic, fractal topographies which exhibit power-law height energy spectrum, $E_h (k) \sim k^{\beta _s}$ , where $\beta _s$ is a (predefined) spectral exponent. These topographies are convenient since they resemble natural landscapes and $\beta _s$ can be varied to change the topography’s aerodynamic roughness (the study considers a suite of topographies with $-2.4 \le \beta _s \le -1.2$ , where $-2.4$ and $-1.2$ are the “most smooth” and “most rough” cases, respectively, corresponding with roughness Reynolds number, $Re_0 \approx 10$ and $300$ ). It is often assumed that $z_{0S}/z_{0} \approx 10^{-1}$ for all $Re_0$ . But results from this work show that the roughness length ratio, $z_{0S}/z_{0}$ , depends strongly on $Re_0$ , ranging between $10^{-3}$ and $10^{-1}$ .     

Dominant features in three-dimensional turbulence structure: comparison of non-uniform accelerating and decelerating flows

The results are presented from an experimental study to investigate three-dimensional turbulence structure profiles, including turbulence intensity and Reynolds stress, of different non-uniform open channel flows over smooth bed in subcritical flow regime. In the analysis, the uniform flow profiles have been used to compare with those of the non-uniform flows to investigate their time-averaged spatial flow turbulence structure characteristics. The measured non-uniform velocity profiles are used to verify the von Karman constant κ and to estimate sets of log-law integration constant B_r and wake parameter П, where their findings are also compared with values from previous studies. From κ, B_r and П findings, it has been found that the log-wake law can sufficiently represent the non-uniform flow in its non-modified form, and all κ, B_r and П follow universal rules for different bed roughness conditions. The non-uniform flow experiments also show that both the turbulence intensity and Reynolds stress are governed well by exponential pressure gradient parameter β equations. Their exponential constants are described by quadratic functions in the investigated β range. Through this experimental study, it has been observed that the decelerating flow shows higher empirical constants, in both the turbulence intensity and Reynolds stress compared to the accelerating flow. The decelerating flow also has stronger dominance to determine the flow non-uniformity, because it presents higher Reynolds stress profile than uniform flow, whereas the accelerating flow does not.     

Turbulence characteristics within sparse and dense canopies

Boundary layer interactions with canopies control various environmental processes. In the case of dense and homogeneous canopies, the so-called mixing layer analogy is most generally used. When the canopy becomes sparser, a transition occurs between the mixing layer and the boundary layer perturbed by interactions between element wakes. This transition has still to be fully understood and characterized. The experimental work presented here deals with the effect of the canopy density on the flow turbulence and involves an artificial canopy placed in a fully developed turbulent boundary layer. One and two-component velocity measurements are performed, both within and above the canopy. The influence of the spacing between canopy elements is studied. Longitudinal velocity statistical moments and Reynolds stresses are calculated and compared to literature data. For spacings greater than the canopy height, evidences of this transition are found in the evolution of the skewness factor, shear length scale and mixing length.     

Compound channel flow with a longitudinal transition in hydraulic roughness over the floodplains

Flows in a compound open-channel (two-stage geometry with a main channel and adjacent floodplains) with a longitudinal transition in roughness over the floodplains are experimentally investigated in an 18 m long and 3 m wide flume. Transitions from submerged dense vegetation (meadow) to emergent rigid vegetation (wood) and vice versa are modelled using plastic grass and vertical wooden cylinders. For a given roughness transition, the upstream discharge distribution between main channel and floodplain (called subsections) is also varied, keeping the total flow rate constant. The flows with a roughness transition are compared to flows with a uniformly distributed roughness over the whole length of the flume. Besides the influence of the downstream boundary condition, the longitudinal profiles of water depth are controlled by the upstream discharge distribution. The latter also strongly influences the magnitude of the lateral net mass exchanges between subsections, especially upstream from the roughness transition. Irrespective of flow conditions, the inflection point in the mean velocity profile across the mixing layer is always observed at the interface between subsections. The longitudinal velocity at the main channel/floodplain interface, denoted \(U_{int}\), appeared to be a key parameter for characterising the flows. First, the mean velocity profiles across the mixing layer, normalised using \(U_{int}\), are superimposed irrespective of downstream position, flow depth, floodplain roughness type and lateral mass transfers. However, the profiles of turbulence quantities do not coincide, indicating that the flows are not fully self-similar and that the eddy viscosity assumption is not valid in this case. Second, the depth-averaged turbulent intensities and Reynolds stresses, when scaled by the depth-averaged velocity \(U_{d,int}\) exhibit two plateau values, each related to a roughness type, meadow or wood. Lastly, the same results hold when scaling by \(U_{d,int}\) the depth-averaged lateral flux of momentum due to secondary currents. Turbulence production and magnitude of secondary currents are increased by the presence of emergent rigid elements over the floodplains. The autocorrelation functions show that the length of the coherent structures scales with the mixing layer width for all flow cases. It is suggested that coherent structures tend to a state where the magnitude of velocity fluctuations (of both horizontal vortices and secondary currents) and the spatial extension of the structures are in equilibrium.     

Mass transfer limitation of photosynthesis of coral reef algal turfs

Algal turfs are the major primary producing component on many coral reefs and this production supports higher levels in the complex reef trophic web. Rates of metabolism of algal turfs are related positively to water motion, consistent with limitation by the diffusion of a substance through a boundary layer. Based on engineering mass transfer theory, we hypothesized that photosynthesis of algal turfs is controlled by rates of mass transfer and responses of photosynthesis to increasing flow speed should be predicted by engineering correlations. This hypothesis was tested in ten experiments where photosynthesis was estimated in a flume/respirometer from changes in dissolved oxygen at eight flow speeds between 0.08 and 0.52 m/s. Flow in the flume and over the reef at Kaneohe Bay, Oahu, Hawaii was estimated using hot-film thermistor and electromagnetic current meters. Rates of photosynthesis were related positively to flow in all experiments and plots of the log of the average Sherwood number (Sh _meas) versus log Reynolds number (Re _D) for each experiment are lower than predicted for mass transfer through a turbulent boundary layer. Algal turf-covered plates are characterized as hydrodynamically transitional to fully rough surfaces and the lower than predicted slopes suggest that roughness reduces rates of mass transfer. A negative correlation between algal turf biomass and slopes of the log Sh _meas−log Re _D plots suggests that mass transfer to algal turfs is affected significantly by the physical structure of the algal community. Patterns of photosynthesis based on changes in dissolved oxygen and dissolved inorganic carbon concentrations (DIC) indicate that the flow speed effect is not the result of increased flux of oxygen from the algal turfs, and combined with the short response time to flow speed, suggest that DIC may limit rates of photosynthesis. Although there are differences between flow in the flume and flow over algal turfs on the reef, these results suggest that photosynthesis is controlled, at least in part, by mass transfer. The chemical engineering approach provides a framework to pose further testable hypotheses about how algal canopy height, flow oscillation, turbulence, and substratum roughness may modulate rates of metabolism of coral reef algal turfs.     

Experimental and numerical investigation of density current over macro-roughness

The dynamics of density current over a bottom covered by macro-roughness elements were investigated by laboratory experiments and a computational model using large eddy simulations. The macro-roughness considered had significant size in comparison with the scale of density current. Five different roughness conditions were considered, namely flat bottom (for reference), half spheres, fine gravels, medium gravels, and large gravels. These bottom conditions had variations in roughness element size, shape, angularity, and spatial configuration. The density current was a lock-exchange type with a density difference of 1% between the two fluids initially separated by a gate in the middle. In the computational model, the roughness was captured using two different methods depending on the size of the roughness elements. For the large roughness elements, i.e., the half spheres and the medium and large gravels, an immersed boundary method was used to resolve the surface of each gravel, which was obtained through 3D laser scanning. The realistic and physically correct placement of these scanned objects in the simulation domain was achieved using a computer tool which can detect the collision of rigid bodies and simulate their dynamics. For the fine gravels, a rough wall function was used. The computational model was validated with the data measured in the experiments, including front position and velocity, and point velocity measurement within the current. The results show that density currents over macro-roughness have distinct behavior from those over a smooth boundary. The characteristics (size, angularity, and pavement pattern) of the macro-roughness play a key role in the current development. Macro-roughness significantly retards the front propagation and enhances entrainment.     

Influence of the secondary motions on pollutant mixing in a meandering open channel flow

This paper presents large eddy simulation of turbulent flow in a meandering open channel with smooth wall and rectangular cross-section. The Reynolds number based on the channel height is 40,000 and the aspect ratio of the cross-section is 4.48. The depth-averaged mean stream-wise velocity agree well to experimental measurements. In this specific case, two interacting cells are formed that swap from one bend to the other. Transport and mixing of a pollutant is analysed using three different positions of release, e.g. on the inner bank, on the outer bank and on the centre of the cross section. The obtained depth-average mean concentration profiles are reasonably consistent with available experimental data. The role of the secondary motions in the mixing processes is the main focus of the discussion. It is found that the mixing when the scalar is released on the centre of the cross-section is stronger and faster than the mixing of the scalar released on the sides. When the position of release is close to a bank side, the mixing is weaker and a clear concentration of scalar close to the corresponding side-wall can be observed in both cases.     

Spatial evolution of coherent motions in finite-length vegetation patch flow

A number of experimental studies on submerged canopy flows have focused on fully-developed flow and turbulent characteristics. In many natural rivers, however, aquatic vegetation occurs in patches of finite length. In such vegetated flows, the shear layer is not formed at the upstream edge of the vegetation patch and coherent motions develop downstream. Therefore, more work is neededz to reveal the development process for large-scale coherent structures within vegetation patches. For this work, we considered the effect of a limited length vegetation patch. Turbulence measurements were intensively conducted in open-channel flows with submerged vegetation using Particle Image Velocimetry (PIV). To examine the transition from boundary-layer flow upstream of the vegetation patch to a mixing-layer-type flow within the patch, velocity profiles were measured at 33 positions in a longitudinal direction. A phenomenological model for the development process in the vegetation flow was developed. The model decomposed the entire flow region into four zones. The four zones are the following: (i) the smooth bed zone, (ii) the diverging flow zone, (iii) the developing zone and (iv) the fully-developed zone. The PIV data also confirmed the efficiency of the mixing-layer analogy and provided insight into the spatial evolution of coherent motions.     

A numerical (LES) investigation of a shallow-water, mid-latitude, tidally-driven boundary layer

We investigate turbulent mixing in a tidally driven, mid-latitude, shallow-water basin. The study is carried out numerically at a laboratory-scale, using large-eddy simulation. We compared the results of the simulation with those of a correspondent purely oscillatory flow (Stokes boundary layer). The effect of rotation on the flow dynamics is twofold. First, rotation gives rise to a mean spanwise flow that concurs to redistribute the turbulent energy among the Reynolds stresses, in particular between the horizontal directions, thus increasing the mixing across the water column and thickening the layer where developed turbulence is observable. Second, the presence of the horizontal component of the background vorticity (latitude effect) breaks the symmetry between the two semi-cycles of the oscillation, since turbulence results suppressed/enhanced during the first/second semi-cycle. These two effects significantly modify the turbulent characteristics with respect to the purely oscillating flow, although the mechanisms that generates turbulence present similar features. The qualitative agreement between our results and some measurements carried out in two sites with characteristics similar to the case analyzed suggests that the outcomes here provided may be of general use for the analysis of mid-latitude, neutrally stratified, shallow-water basins mainly driven by semi-diurnal tidal currents.     

Canopy-wake dynamics and wind sheltering effects on Earth surface fluxes

The atmospheric boundary layer adjustment at the abrupt transition from a canopy (forest) to a flat surface (land or water) is investigated in a wind tunnel experiment. Detailed measurements examining the effect of canopy turbulence on flow separation, reduced surface shear stress and wake recovery are compared to data for the classical case of a solid backward-facing step. Results provide new insights into the interpretation for flux estimation by eddy-covariance and flux gradient methods and for the assessment of surface boundary conditions in turbulence models of the atmospheric boundary layer in complex landscapes and over water bodies affected by canopy wakes. The wind tunnel results indicate that the wake of a forest canopy strongly affects surface momentum flux within a distance of 35–100 times the step or canopy height, and mean turbulence quantities require distances of at least 100 times the canopy height to adjust to the new surface. The near-surface mixing length in the wake exhibits characteristic length scales of canopy flows at the canopy edge, of the flow separation in the near wake and adjusts to surface layer scaling in the far wake. Components of the momentum budget are examined individually to determine the impact of the canopy wake. The results demonstrate why a constant flux layer does not form until far downwind in the wake. An empirical model for surface shear stress distribution from a forest canopy to a clearing or lake is proposed.     

Observations of the cross-wind velocity variance in the stable boundary layer

Nine tower datasets over grassland, brush rangeland, snow covered plain, the ocean, three different pine forests, an aspen forest and an urban site, are used to document the scale-dependence of the cross-wind velocity variance in the stable boundary layer. The turbulence velocity variance scales with the surface momentum flux, as reported in previous studies. Such scaling removes the stability dependence of the variance at a given site, and also removes most of the differences between sites. The scaling is more effective with use of a record-dependent averaging time for defining the turbulent fluctuations. The variable averaging time is the timescale associated with the gap region in the heat flux multiresolution cospectra. On scales larger than turbulence and less than a few hours (mesoscale), variations in the cross-wind velocity variance at a given site are not related to local variables such as the friction velocity. Possible exceptions include suppression of turbulence and mesoscale motions in well-defined drainage flows and enhancement of turbulence and mesoscale motions in stronger winds downstream of a ridge. Larger mesoscale variance is associated with complex terrain and forested sites compared to the more homogeneous sites in flat terrain with short or no vegetation. These differences between sites are related to the absence of a gap region in the velocity spectra at the complex terrain and forested sites. The observed probability distribution functions of the total variance and the mesoscale variance are documented for different averaging times, stability classes and site characteristics.     

Hydrodynamics and turbulence in emergent and sparsely vegetated open channel flow

This present study reports the results of an experimental study characterizing thorough variation of turbulent hydrodynamics and flow distribution in emergent and sparsely vegetated open channel flow. An emergent and rigid sparse vegetation patch with regular spacing between stems along the flow and transverse directions was fixed in the central region of the cross-section of open channel. Experiments were conducted in subcritical flow conditions and velocity measurements were obtained with an acoustic Doppler Velocimetry system. Large variations of the turbulence intensities, Reynolds shear stress, turbulent kinetic energy and vortical motions are found in and around the vegetation patch. At any cross-section through the interior of the vegetation patch, streamwise velocity decreases with increase in streamwise length and the velocity profiles converge from the log-law to a linear profile with increasing slope. Time-averaged lateral and vertical velocities inside the vegetation patch increase with increasing streamwise distance and converge from negative values to positive values. Turbulence intensities interior of the sparse vegetation patch are more than those of without the vegetation patch. Similar to the trend of streamwise velocity profiles inside the vegetation, turbulence intensities and longitudinal-normal Reynolds shear stress profile decreases with streamwise direction. In the interior of the vegetation patch and downstream of the trailing edge, turbulent kinetic energy profiles are exhibiting irregular fluctuations and the maximum values are occurring in the outer layer. Analysis of flow distribution confirms sparse vegetation patch is inducing a serpentine flow pattern in its vicinity. At the leading edge, flow is rushing towards the right hand sidewall, and at the trailing edge, flow is turning to the left hand sidewall. In between the leading and trailing edges, the streamlines are following a zig-zag fashion at varied degree along the streamwise and lateral directions. Immediate upstream of the leading edge and in the interior of the vegetation patch, vortex motion is clearly visible and the vortices are stretched along the width of the channel with streamwise direction.     

Flows through forest canopies in complex terrain

Recent progress on boundary layer flow within and above tall forest canopies in complex terrain is reviewed from the perspective of developing methods to interpret carbon dioxide fluxes from tower measurements in real terrain. Two examples of complex terrain are considered in detail: a forest edge, which exemplifies nonuniform forests, and hilly terrain, which can lead to drainage currents at night. Dynamical arguments show that, when boundary layer winds approach a forest edge, the mean wind adjusts on a length scale of approximately 3L(c), where L(c) is the canopy drag length scale, which depends inversely on the leaf area density of the forest. Over a further distance that also scales on L(c), turbulence in the flow adjusts, and the mixing and transport in the canopy approaches the homogeneous limit. Even low hills change the neutral flow within and above the forest canopy substantially. When the canopy is tall, pressure gradients drive flow up both the upwind and downwind slopes of the hill, leading to an ejection of air out of the top of the canopy just downwind of the crest. This flow at the crest can then advect scalar out of the top of the forest, leading to large variations in the flux of scalar across the hill. At night, when the air near the ground cools and becomes stably stratified, turbulence within the canopy can collapse, even when the flow above the canopy remains turbulent. This leads to a decoupling of the air motions within the canopy from those above. The air above the canopy can then continue to pass up and over the hill, as it does in the neutral case, but at the same time, air within the canopy drains down the hill slopes as drainage currents. These analyses will help us understand when flux towers are reliably measuring the net ecosystem exchange and suggest ways of correcting the flux tower data in more complex situations.     

Experimental study of recirculating flows generated by lateral shock waves in very large channels

Due to the lack of data on hydraulic-jump dynamics in very large channels, the present paper describes the main characteristics of the velocity field and turbulence in a large rectangular channel with a width of 4 m. Although a hydraulic jump is always treated as a wave that is transversal to the channel wall, in the case of this study it has a trapezoidal front shape, first starting from a point at the sidewalls and then developing downstream in an oblique manner, finally giving rise to a trapezoidal shape. The oblique wave front may be regarded as a lateral shockwave that arises from a perturbation at a certain point of the lateral wall and travels obliquely toward the centreline of the channel. The experimental work was carried out at the Coastal Engineering Laboratory of the Water Engineering and Chemistry Department of the Technical University of Bari (Italy). In addition to the hydraulic jump formation, a large recirculating flow zone starts to develop from the separating point of the lateral shock wave and a separate boundary layer occurs. Intensive measurements of the streamwise and spanwise flow velocity components along one-half width of the channel were taken using a bidimensional Acoustic Doppler Velocimeter (ADV). The water surface elevation was obtained by means of an ultrasonic profiler. Velocity vectors, transversal velocity profiles, turbulence intensities and Reynolds shear stresses were all investigated. The experimental results of the separated boundary layer were compared with numerical predictions and related work presented in literature and showed good agreement. The transversal velocity profiles indicated the presence of adverse pressure gradient zones and the law of the wall appears to govern the region around the separated boundary layer.     

Turbulence structure and coherent vortices in open-channel flows with wind-induced water waves

When wind-induced water waves appear over the free-surface flows such as natural rivers and artificial channels, large amounts of oxygen gas and heat are transported toward the river bed through the interface between water and wind layers. In contrast, a bed region is a kind of turbulent boundary layer, in which turbulence generation and its transport is promoted by the production of bed shear stress. In particular, coherent hairpin vortices, together with strong ejection events toward the outer part of the layer, promote mass and momentum exchanges between the inner and outer layers. It is inferred that such a near-bed turbulence may be influenced significantly by these air–water interfacial fluctuations accompanied with free-surface velocity shear and wind-induced water waves. However, these wind effects on the wall-turbulence structure are less understood. To address these exciting and challenging topics, we conducted particle imagery velocimetry (PIV) measurements in open-channel flows combined with air flows, and furthermore the present measured data allows us to investigate the effects of air–water interactions on turbulence structure through the whole depth region.