Recovery of boric acid from boronic wastes by leaching with water,carbon dioxide- or sulfur dioxide-saturated water and leaching kinetics

B₂O₃ was recovered from waste samples such as borogypsum, reactor waste, boronic sludges, waste mud and concentrator waste by leaching processes using distilled water, sulfur dioxide- and carbon dioxide-saturated water. In the leaching processes, temperature, stirring time and solid-to-liquid ratio were taken as parameters. The amount of B₂O₃ leached increased with increasing temperature and stirring time and it also increased with decreasing solid-to-liquid ratio, but the increase was less than that recorded for the leaching temperature and the stirring time. SO₂ saturated water is a more effective leaching solvent than CO₂ saturated water for boronic wastes. By the end of the experiments, more than 90% of B₂O₃ recovery was found as boric acid. In the leaching of boric acid from boronic wastes in water saturated with sulfur dioxide, it was observed that the leaching rate increases with increasing temperature and leaching time. The overall average values of the kinetic parameters were: apparent activation energy (E) 33.2 kJ mol⁻¹, pre-exponential factor (A) 8.2×10⁹ min⁻¹, reaction order (n) 0.97 and rate constant (k) 3.37×10³ min⁻¹ for the leaching processes of the boronic wastes.     

Environmental and economic impact assessment of construction and demolition waste disposal using system dynamics

Construction and demolition wastes (CDW) have increasingly serious problems in environmental, social, and economic realms. There is no coherent framework for utilization of these wastes which are disposed both legally and illegally. This harms the environment, contributes to the increase of energy consumption, and depletes finite landfills resources. The aim of this paper is to evaluate the impacts of two alternatives for the management of CDW, recycling and disposing. The evaluation is carried out through developing a dynamic model with aid STELLA software by conducting the following steps: (1) quantifying the total cost incurred to mitigate the impacts of CDW landfills and uncollected waste on the environment and human health; (2) quantifying the total avoided emissions and saved energy by recycling waste; (3) estimating total external cost saved by recycling waste and; (4) providing a decision support tool that helps in re-thinking about waste disposal. The proposed evaluation methodology allows activating the stringent regulations that restrict waste disposal and developing incentives to encourage constructors to recycle their wastes. The research findings show that recycling CDW leads to significant reductions in emissions, energy use, global warming potential (GWP), and conserves landfills space when compared to disposal of wastes in landfills. Furthermore, the cost of mitigating the impact of disposal is extremely high. Therefore, it is necessary to recycle construction and demolition wastes.     

RATES,RIGHTS, AND REGIONAL PLANNING IN THE METROPOLITAN WATER DISTRICT OF SOUTHERN CALIFORNIA1

ABSTRACT: The Metropolitan Water District of Southern California has for more than 70 years shaped the development of an immense urban region. The district's current strategic planning process therefore could have substantial effects on regional water planning and management. The rate restructuring phase of the planning process has produced a multiple component, cost of service based framework. This paper describes that framework as well as some criticisms that have been directed toward it. The rate restructuring was shaped, and for a while stalled, by old disputes among member agencies over rights to water supplied by Metropolitan. That controversy has diverted attention from the resource management implications of the rate structure. This paper presents an alternative future focused approach to regional integrated water resource planning for Southern California based on projections of current trends and anticipation of future events. This discussion raises the question of how regional integrated water resources planning of this sort may proceed, and what role Metropolitan will play in that process.     

Recovery of biomass wastes by hydrolysis in sub-critical water

The recovery of waste substances is important not only for the prevention of environmental issues, but also for the rational utilization of natural resources. Hydrolysis reaction in sub-critical water is a promising method for the treatment of organic wastes and has been attracting worldwide attention. In this paper, sub-critical water hydrolysis was employed as a method for producing amino acids, reducing sugars, bio-oil and gas fuels from biomass wastes. The current statuses of these useful chemicals production from biomass wastes by hydrolysis in sub-critical water were reviewed. The review indicates that sub-critical water hydrolysis can be an efficient process for recovering useful chemicals from biomass wastes. This method is renewable, sustainable, efficient, and safe for the environment.     

Novel passive co-treatment of acid mine drainage and municipal wastewater

A laboratory-scale, four-stage continuous-flow reactor system was constructed to test the viability of high-strength acid mine drainage (AMD) and municipal wastewater (MWW) passive co-treatment. Synthetic AMD of pH 2.6 and acidity of 1870 mg L(-1) as CaCO3 equivalent containing a mean 46, 0.25, 2.0, 290, 55, 1.2, and 390 mg L(-1) of Al, As, Cd, Fe, Mn, Pb, and Zn, respectively, was added at a 1:2 ratio with raw MWW from the City of Norman, OK, to the system which had a total residence time of 6.6 d. During the 135-d experiment, dissolved Al, As, Cd, Fe, Mn, Pb, and Zn concentrations were consistently decreased by 99.8, 87.8, 97.7, 99.8, 13.9, 87.9, and 73.4%, respectively, pH increased to 6.79, and net acidic influent was converted to net alkaline effluent. At a wasting rate of 0.69% of total influent flow, the system produced sludge with total Al, As, Cd, Cr, Cu, Fe, Pb, and Zn concentrations at least an order of magnitude greater than the influent mix, which presents a metal reclamation opportunity. Results indicate that AMD and MWW passive co-treatment is a viable approach to use wastes as resources to improve water quality with minimal use of fossil fuels and refined materials.     

Biosolid colloid-mediated transport of copper, zinc, and lead in waste-amended soils

Increasing land applications of biosolid wastes as soil amendments have raised concerns about potential toxic effects of associated metals on the environment. This study investigated the ability of biosolid colloids to transport metals associated with organic waste amendments through subsurface soil environments with leaching experiments involving undisturbed soil monoliths. Biosolid colloids were fractionated from a lime-stabilized, an aerobically digested, and a poultry manure organic waste and applied onto the monoliths at a rate of 0.7 cm/h. Eluents were monitored for Cu, Zn, Pb, and colloid concentrations over 16 to 24 pore volumes of leaching. Mass-balance calculations indicated significantly higher (up to 77 times) metal elutions in association with the biosolid colloids in both total and soluble fractions over the control treatments. Eluted metal loads varied with metal, colloid, and soil type, following the sequences Zn = Cu > Pb, and ADB > PMB > LSB colloids. Colloid and metal elution was enhanced by decreasing pH and colloid size, and increasing soil macroporosity and organic matter content. Breakthrough curves were mostly irregular, showing several maxima and minima as a result of preferential macropore flow and multiple clogging and flushing cycles. Soil- and colloid-metal sorption affinities were not reliable predictors of metal attenuation/elution loads, underscoring the dynamic nature of transport processes. The findings demonstrate the important role of biosolid colloids as contaminant carriers and the significant risk they pose, if unaccounted, for soil and ground water contamination in areas receiving heavy applications of biosolid waste amendments.     

Environmental impact and risk assessment of mineral wastes reuse strategies: Review and critical analysis of approaches and applications

In the industrial practice, the choice and evaluation of strategies of recycling and reuse of solid mineral wastes (thermal process residues, mining and quarrying wastes, construction and demolition wastes) could be based on ecological risk assessment (EcoRA) and life cycle assessment (LCA) studies also because of the substantial lack of regulations. Several methods and approaches of EcoRA and LCA have been developed so far and it is not always evident to consider a pertinent method for each application case. Furthermore, it is even less trivial to combine local and global scale results so to identify the best scenario from different alternatives.After a comprehensive review of recycling and reuse routes of mineral waste and relative legislation, this study addresses these issues by providing a detailed analysis and comparison of global and local scale impact assessment methods used in LCA and EcoRA, and finally an inventory of LCA and EcoRA studies already completed, to serve as a basis for further research.     

Nickel recovery/removal from industrial wastes: A review

Nickel is an important metal, heavily utilized in industry mainly due to its anticorrosion properties. As a consequence, nickel containing wastes such as spent batteries and catalysts, wastewater and bleed-off electrolytes are generated in various processes. These wastes could have a negative impact on the environment and human health if they contaminate soil, water and air. The present review addresses the environmental and economical aspects of nickel recovery/removal from various types of wastes. The main physico-chemical technologies for processing various effluents and wastewaters containing nickel are reviewed and discussed. Nickel recovery from spent batteries, catalysts, electronic waste and other sources is described. Hydrometallurgical approaches are emphasized. Recovery of nickel from wastes is important not only for economical aspects, but also for environmental protection.     

Oxidation kinetics of the combustible fraction of construction and demolition wastes

Proper disposal of construction and demolition wastes (CDW) has received wide attention recently due to significantly large quantities of waste streams collected from razed or retrofitted buildings in many metropolitan regions. Burning the combustible fractions of CDW (CCDW) and possibly recovering part of the heat content for economic uses could be valuable for energy conservation. This paper explores the oxidation kinetics of CCDW associated with its ash characterization. Kinetic parameters for the oxidation of CCDW were numerically calculated using thermal gravimetric analysis (TGA) and the resultant rate equations were therefore developed for illustrating the oxidation processes of CCDW simultaneously. Based on three designated heating rates, each of the oxidation processes can be featured distinctively with five different stages according to the rate of weight change at the temperature between 300 K and 923 K. In addition, Fourier transform infrared (FTIR) spectroscopy was employed, associated with a lab-scale fixed-bed incinerator for monitoring the composition of flue gas. Carbon dioxide (CO2) was found as a major component in the flue gas. The fuel analysis also included an ash composition analysis via the use of X-ray powder diffraction (XRD), atomic absorption (AA) spectroscopy, inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDX). The ash streams were identified as nonhazardous materials based on the toxicity characteristic leaching procedure (TCLP). Overall, the scientific findings gained in this study will be helpful for supporting a sound engineering design of real-world CCDW incineration systems.     

我国南方某城市垃圾焚烧飞灰特性及固化/稳定化处置实验

我国南方某城市主要采用焚烧法处理生活垃圾,已建7个焚烧厂日产生飞灰量为101.62 t/d。文章分析了各个垃圾焚烧厂飞灰的化学组成和重金属浸出毒性,其主要成分为CaO、SiO2、MgO、Al2O3、Fe2O3、Na2O、SO3和Cl,所有焚烧飞灰都有至少一种重金属浸出浓度超标,属于危险废物。在飞灰处置出路亟待解决的背景下,实验探讨了飞灰稳定化工艺,结果表明10%的水泥添加量可以使飞灰中超标重金属(Cd、Pb和Zn)的浸出浓度满足危险废物鉴别浓度限值和安全填埋场入场浓度限值。同时,通过人体健康风险评价分析了飞灰豁免管理的可行性,并对近期和远期该城市焚烧厂飞灰的处理处置及管理提出建议。     

火力发电行业的环境污染与水资源利用

讨论了电源点建设所面临的环境保护和水资源紧缺的影响,提出根据电源点总体发展和分布,科学制定水资源储备战略思路。建议新的电源点建设可以规划采用城市污水、矿井水等作为火力发电厂项目建设的用水发展方向,海滨电厂可以采用电、热、水一体的建设模式,实现循环经济。     

An overview for the utilization of wastes from stainless steel industries

Significant quantities of wastes are generated as the waste materials or byproducts every day from stainless steel processes. According to the origins and characteristics, the stainless steel wastes can be mainly classified into two categories, slags and dusts. They usually contained considerable quantities of valuable metals and materials. This paper summarized and analyzed the generation, composition, characteristics and the leaching behaviors of the most of wastes obtained from the stainless steel processes. On this basis, a review of several methods for treating the various stainless steel wastes was made. It is very essential not only for recycling the valuable metals and mineral resources but also for protecting the environment.     

建筑废弃物再生利用的可行性技术研究综述

建材行业的发展为城市化建设提供了重要保障,在我国城市化快速发展、建筑材料需求旺盛的带动下,建材行业发展强劲,但大多属于高能耗高污染行业,加之城市拆迁改造产生大量建筑废弃物,环境压力十分巨大,必须加强建筑废弃物的环境管理。对建筑废弃物再利用、再循环以及减少建筑废弃物是解决建筑行业环境问题的重要方式,实施这些仍有很大的提升空间。本文回顾了近年来建筑废弃物再生利用方面的各种可行性技术。主要是针对沥青、砖、混凝土、金属、玻璃等几种物质再生利用的可行性技术进行综述,为未来建筑废弃物再生利用领域提供参考。     

Decontamination of Fly Ash and Used Lime from Municipal Waste Incinerator Using Thiobacillus ferrooxidans

Thiobacillus ferrooxidans to leach metals from APCR to render them nonhazardous. The multistage solubilization process involves an alkaline aqueous phase that removes some Pb. In the second phase, the APCR are acidified to pH 4 with H₂SO₄, then inoculated with a bacterial culture that has been acclimated in the presence of 2% Fe (FeCl₃). Several rinses and decantings achieve removal of the leachable metals. The final step involves the addition of Ca(H₂PO₄)₂ and an increase in the treatment pH prior to the final filtration. Viability of thiobacilli in APCR was poor. Despite this problem, the removal of Pb was 35.9%, 46.0%, and 68.7% (for APCR containing 1594, 3026, and 5038 mg Pb/kg, respectively), which demonstrates greater metal removal with increased APCR contamination. Zn removal varied from 68.2% (8273 mg Zn/kg APCR) to 79.5% (16,873 mg Zn/kg APCR), which was positively correlated to the level of residue contamination, whereas Cu was removed in the proportions of 26.9% (495 mg Cu/kg APCR) to 68.2% (465 mg Cu/kg APCR). Cadmium removal appeared to be independent of the level of Cd in the APCR; Cd was removed to the greatest degree, with a variation of 92.0% (129 mg Cd/kg APCR) to 94.7% (267 mg Cd/kg APCR). The treated APCR were tested using four different leachate tests. The APCR released 43 mg Pb/liter during contact with water, and 7.40 mg Cd/liter during TCLP [the toxicity characterization leaching procedure of the United States Environmental Protection Agency (US EPA)]. After biological treatment, the leachate from TCLP was within the acceptance criteria of the US EPA, if the pH of the APCR was increased to pH 5 after the biological treatment. In the case of the Transport Canada leaching test, a betterment of the process is required in order to satisfy the stringent regulatory level of 0.5 mg Cd/liter (0.68 and 0.57 mg/liter).     

Distribution of copper, zinc, and phosphorus in coastal plain soils receiving repeated liquid biosolids applications

Continuous N-based application of biosolids contributes to a gradual increase of trace elements and P in soils. The objectives of this study were to assess the accumulation and vertical transport of Cu, Zn, C, N, and P within the profile of two coastal plain soils. Liquid (6-8% total solids) biosolids were applied to an Acredale silt loam (fine silty, mixed, thermic typic Ochraqualfs) and Bojac loamy sand (coarse loamy, mixed, thermic typic Hapludult) annually from 1984 to 1998. The repeated applications supplied 70, 204, and 3823 kg ha(-1) of Cu, Zn, and P, respectively, to the Acredale and 81, 225, and 4265 kg ha(-1) of Cu, Zn, and P, respectively, to the Bojac. The total C and N contents were not different than background levels in the Bojac soil and were slightly higher in the Acredale soil 7 years after cessation of biosolids application. Phosphorus, Cu and Zn are still concentrated in the top 0.25 m of the Acredale soil. Enrichment of P, Cu, and Zn were detected to the deepest soil increment in the coarse-textured Bojac soil. Approximately 20 to 40% of the Cu and Zn applied in the biosolids could not be accounted, which was likely due to a combination of leaching and incomplete extraction. Excessive Mehlich 1-P concentrations and a high degree of P saturation were found in amended soil, raising the potential for P release to runoff or leaching water.     

Nitrate leaching and nitrogen recovery following application of polyolefin-coated urea to potato

High N fertilizer and irrigation amounts applied to potato (Solanum tuberosum L.) on coarse-textured soils often result in nitrate (NO3) leaching and low recovery of applied fertilizer N. This 3-yr study compared the effects of two rates (140 and 280 kg N ha(-1)) of a single polyolefin-coated urea (PCU) application versus split applications of urea on 'Russet Burbank' potato yield and on NO3 leaching and N recovery efficiency (RE) on a loamy sand. Standard irrigation was applied in all years and excessive irrigation was used in another experiment in the third year. At the recommended rate of 280 kg N ha(-1), NO3 leaching during the growing season was 34 to 49% lower with PCU than three applications of urea. Under standard irrigation in the third year, leaching from five applications of urea (280 kg N ha(-1)) was 38% higher than PCU. Under leaching conditions in the first year (> or = 25 mm drainage water in at least one 24-h period) and excessive irrigation in the third year, PCU at 280 kg N ha(-1) improved total and marketable tuber yields by 12 to 19% compared with three applications of urea. Fertilizer N RE estimated by the difference and 15N isotope methods at the 280 kg N ha(-1) rate was, on average, higher with PCU (mean 50%) than urea (mean 43%). Fertilizer N RE values estimated by the isotope method (mean 51%) were greater than those estimated by the difference method (mean 47%). Results from this study indicate that PCU can reduce leaching and improve N recovery and tuber yield during seasons with high leaching.     

我国医疗废物处理的现状及改进措施

医疗废物被列为《国家危险废物名录》的首位,处理不彻底会对水体、土壤、空气和人体造成严重危害。然而,我国对医疗废物的处理起步比较晚,和世界发达国家相比处于落后状态。目前,我国的医疗废物总量逐年增加,集中处理率低,收集、分类、贮存、运输不规范,并且缺乏有效的监管体系和运行机制,应该采取加强医疗废物源头控制、建立医疗废物监管体制、提高医疗废物处理技术和能力等措施,力争在较短的时间内彻底改变我国医疗废物处理现状。     

生活垃圾中再生资源的循环利用模式探析

目前我国的生活垃圾中的再生资源回收利用率较高，再利用的过程基本是市场驱动的，但具有负外部性和不可持续性。应通过扩大生产者责任来重构循环利用体系，减少对环境的不利影响。本文在分析总结上海一次性饭盒回收利用经验的基础上，探讨了在我国推行扩大生产者责任制度的对策。     

FISH AND WILDLIFE ENHANCEMENT THROUGH WATER RESOURCES DEVELOPMENT1

.Fish and wildlife enhancement through water resources development implies fish and wildlife will be enhanced or benefit directly from such development. As a matter of practicality, the opposite may be the case in that wildlife lands of prime value and stream fisheries are often lost or severely altered as a result of reservoir construction or stream channelization. Additionally, estuarine fish and wildlife can also suffer from water resources development due to reductions in volume of fresh waters reaching the estuaries and adjacent marshes. In some instances waterfowl habitat can be created by reservoir construction and with good planning waterfowl habitat and use may be enhanced. To offset losses of thousands of acres of wildlife habitat when a river system is to be totally harnessed, planners could set aside sufficiently large natural areas dedicated for use by wildlife. This, however, would be replacement rather than enhancement. Reservoir fisheries can be enhanced with good planning to include timber clearing, shoreline clearing, boat road clearing, variable level drawoff devices and tailrace escapement channels. To sum up, it is possible for some species offish and wildlife to be enhanced through water resources development but only at the expense of others, and then only through careful and integrated planning.     

油田固体废物的毒性试验研究

通过对某油田3个区域井场的废弃钻井液和取自集输站及注水站的油泥(砂)等两种固体废物进行急性生物毒性试验和浸出毒性试验,试验结果表明:该油田的废弃钻井液急性生物毒性相对较大,油泥(砂)不具有急性生物毒性;这两种固体废物均不具有浸出毒性和腐蚀性。