南充市城市空气质量变化及达标分析

为了掌握南充市近年来城市空气质量变化及其达标情况,对南充市城区2008～2012年SO2、NO2和PM10的质量浓度数据进行统计分析,并计算各个站点的空气污染指数和空气质量指数。结果表明,3种污染物浓度值都有明显的下降趋势,S02浓度在0．002～0．052mg／m^3之间变化;N02浓度值从0．042mg／m^3下降到0．029mg／m^3;PM10浓度在0．060～0．063mg／m^3之间波动。南充市空气质量冬季较差,夏季较好。在5个监测点中,炼油厂空气质量最差,优良率为92．9％（85．1％）;高坪空气质量最好,优良率为99．1％（98．3％）。相关性分析表明,南充市空气污染源主要是工业燃煤和机动车尾气。     

重庆市城区交通干道空气污染特征

于秋冬两季，利用法国生产的自动监测仪对重庆市城区7条交通主干道的近地面空气质量进行了监测。结果表明：在监测期间，各个监测点PM1o是首要污染物，并且秋季比冬季污染严重，7条道路的日平均浓度为0．419mg／m^3，最大浓度为0．687mg／m^3，最大超标率为3．58倍；而NO2和SO2在冬季比秋季污染严重，NO2最高浓度是0.126mg／m^3，平均浓度是0．089mg／m^3，S02最高浓度是0．333mg／m^3，平均浓度是0．216mg／m^3，表明交通干道空气污染严重。     

不同气温条件下室内甲醛污染特性的探讨

用酚试剂分光光度法（GB／F18204．26—2000）对装修后室内空气中的甲醛进行测定。通过一年多的实测表明：气温在13.0℃-24．0℃范围内，测试结果的超标率为27．8％，测试结果均值为0．077mg／m^3，气温在25．0℃-30．0℃范围内，测试结果的超标率为78．1％，测试结果均值为0．270mg／m^3，两个温度段超标率相差2．8倍多，测试结果均值相差3．5倍多。室内空气中甲醛浓度与室内温度呈线性关系，表明气温对室内空气中甲醛的释放量有明显的影响。     

生长于铬污染土壤上石榴产品铬污染评价

研究了攀西地区铬污染土壤和正常土壤铬含量分布及其石榴样品铬污染情况。结果表明攀枝花大田石榴基地土壤铬含量在23．1—504mg／kg，平均值高达184mg／kg，超标率为26％，而对该基地的石榴果实进行两年连续监测结果表明，铬含量在0．0012—0．067mg／kg之间，平均为0．016mg／kg，大大低于相应产品标准（0．5mg／kg），超标率为0％；会理石榴基地土壤铬含量在34．5—99．1mg／kg，平均值为69．0mg／kg，超标率为0％，该基地的石榴果实铬含量在0．0075—0．104mg／kg之间，平均为0．024mg／kg，大大低于相应产品标准（0．5mg／kg），超标率为0％。形态分析表明土壤中铬99％以上都是以不被植物利用的残渣态存在，因此土壤总铬再高，其被植物可吸收部分却很少，这就导致了受铬污染的土壤却不一定能生产出污染石榴的原因。     

活性炭吸附CS2解析气相色谱法测定车间空气中的O,O-二乙基硫代磷酰氯

本文建立了活性炭管吸附CS2解析气相色谱法测定车间空气中微量O，O-二乙基硫代磷酰氯含量的方法，柱温1400c、汽化室温度为250℃、检测器温度250℃，氮气流量为50mL/min，用150mg活性炭管，采样流速为100-200mL／min时，其吸收效率为100％，解析效率为92．5％。方法的相对标准偏差小于10％（n=5），方法检出限为0．3mg／m^3。     

环境空气背景值中PM2．5和PM10的相关性分析

四川省大气背景站颗粒物PM2．5和PM10实时监测结果表明,两个点位的PM2．5浓度占PM10浓度分别为80．15％、68．9％,两个点位的PM2．j浓度和PM10浓度均呈显著线性关系,点位1：y=0．8634x-0．2212,R^2=0．9823;点位2：y=0．7352x-0．2142,R^2=0．7767。     

颗粒活性炭载体新型生物转盘去除生活污水中COD和NH3-N的研究

开发一种改进型生物转盘处理生活污水，将盘片改为转笼状，并向其中加入颗粒活性发作为载体，研究该系统对生活污水的处理效果。结果表明：在转盘转速为15rpm和HRT分别为10h、8h、6h、4．5h情况下，进水COD平均浓度约为223mg／L，出水COD平均浓度分别为15．6、17．9、23．4、28．2mg/L，平均去除率为93．0％、91．9％、89．5％、86．6％；进水NH3-N平均浓度约为22mg／L，出水NH3-N平均浓度分别为0．32、1．13、2．30、5．71mg／L，平均去除率为98．5％、94．8％、89．7％、74．6％。     

生物促生剂修复受污水体净化效能研究

对生物促生剂（Bio-energizer，BE）净化受污水体的效果进行了试验研究。结果表明：生物促生剂在低浓度时（小于1 ml／m^3），水体修复效果不明显；当浓度在3ml／m^3以上时，可以有效的加快水体中N、P类营养物的降解，可使NH4^＋ -N和TN分别由3．6—4．4mg／L和4．4—4．9mg／L降低至0．13-0．18 mg／L和0．39—1．06 mg／L，PO4^3- -P和TP分别由0．03-0．04mg／L和0．11—0．12mg／L降低至0．004-0．008mg／L和0．025-0．04mg／L。COD在试验过程中有上升的趋势。     

异烟酸-吡唑啉酮光度法测定地表水中氰化物的质量控制指标研究

通过对大量监测数据进行统计分析,获得异烟酸-吡唑啉酮光度法（HJ484—2009）测定水中氰化物质量控制评定指标。研究表明：样品浓度在0．05～0．3mg／L范围内时,建议控制室内相对标准偏差≤3％,室间相对标准偏差≤10％;样品浓度小于等于0．05mg／L时,建议控制相对偏差≤10％;样品浓度大于0．05mg／L时,...     

炸药爆轰气体产物中无机组份的离子色谱分析方法研究

采用超纯水、Na2CO3-NaHCO3NaOH3种不同的吸收液吸收爆轰气体产物、离子色谱进行样品分离、外标法定量,建立了爆轰气体产物中HF、HCl、HCN无机污染物的离子色谱分析方法。研究表明,炸药爆轰气体中合有一定量的HF、HCl和少量的HCN,选择3．2mmol／LNa2C03与1．0mmol／LNaHCO3混合溶液作为爆轰产物中无机组份的吸收液,吸收效率均值太于90％;离子色谱分析方法的相对标准偏差（RSD）小于5．0％,相关系数达到0．9990以上;进样量为100μL时,HF、HCl、HCN的检测限分别为0．04mg／m^3、0．03mg／m^3、0．05mg／m^3。该方法灵敏度高,回收率好,且样品预处理简单。     

Robust reliability and electrical performances by the bulk-contact modulation in 60-V p-channel LDMOS power components

To increase reliability and electrical performance, shallow-trench isolation (STI) (or called field-oxide (FOX)) structures were inserted in the bulk-contact region of 60-V high-voltage p-channel lateral-diffused MOSFET (pLDMOS) devices in this study. As the FOX ratio increased with the addition of FOX segments, the value of the secondary breakdown current (I_t2) was enhanced. Therefore, the anti-electrostatic discharge ability of a pLDMOS device can be efficiently improved using this novel method. In addition, when the weighting ratio of FOX structures increased, variation values in the trigger voltage (V_t1) and holding voltage (V_h) of the corresponding samples remained within the range of approximately 1–4 V. The R_on value decreased because of more uniform conduction. The experimental data for the FOX structures added to the bulk revealed that the I_t2 value was improved by approximately 13.98%, V_h values were greater than 60 V (which is favorable for latch-up immunity), and the R_on value was decreased by approximately 12.62% compared with a reference device under test (without FOX segments in the bulk-contact region).     

Environmental and economic aspects of production and utilization of RDF as alternative fuel in cement plants: A case study of Metro Vancouver Waste Management

Municipal solid waste (MSW) disposal and management is one of the most significant challenges faced by urban communities around the world. Municipal solid waste management (MSWM) over the years has utilized many sophisticated technologies and smart strategies. Municipalities worldwide have pursued numerous initiatives to reduce the environmental burden of the MSW treatment strategies. One of the most beneficial MSWM strategies is the thermal treatment or energy recovery to obtain cleaner renewable energy from waste. Among many waste-to-energy strategies, refuse-derived fuel (RDF) is a solid recovered fuel that can be used as a substitute for conventional fossil fuel. The scope of this study is to investigate the feasibility of RDF production with MSW generated in Metro Vancouver, for co-processing in two cement kilns in the region. This study investigates environmental impacts and benefits and economic costs and profits of RDF production. In addition, RDF utilization as an alternative fuel in cement kilns has been assessed. Cement manufacturing has been selected as one of the most environmentally challenged industries and as a potential destination for RDF to replace a portion of conventional fossil fuels with less energy-intensive fuel. A comprehensive environmental assessment is conducted using a life cycle assessment (LCA) approach. In addition, cost–benefit analysis (CBA) has been carried out to study the economic factors. This research confirmed that RDF production and use in cement kilns can be environmentally and economically viable solution for Metro Vancouver.     

A coordinated control strategy using supercapacitor energy storage and series dynamic resistor for enhancement of fault ride-through of doubly fed induction generator

Power fluctuation and fault-related complication are the two major issues for doubly fed induction generator (DFIG)-based wind energy conversion system (WECS). The occurrence of fault leads to the rotor over current, stator over current, and DC-link overvoltage as well. These uncertainties may damage the rotor circuit, converter circuit and force the disconnection of wind system from the grid. To get rid of these issues, a supercapacitor energy storage element along with a passive series dynamic resistor (SDR) is suggested in this paper. Supercapacitor energy storage system (SCESS) is located across the DC-link, which able to handle the power fluctuation and the SDR is placed in rotor circuit, which will reduce the overcurrent possibility. Simulation is carried for a DFIG-based WECS for three phase to ground fault and two phase to ground fault. During symmetrical fault as well as asymmetrical fault, various operational disorders appeared such as rotor overcurrent, stator overcurrent and DC-Link overvoltage are found to be within their permissible limits. The results reveal the effectiveness of the proposed strategy over the conventional vector control scheme and SCESS as well.     

氢化物发生流动注射原子吸收分光光度法测定铅的研究

本研究将氢化物发生(HG)与流动注射分析(FIA)相结合产生PbH_4,采用火焰原子吸收(FAAS)检测铅,灵敏度比FAAS提高了2.5倍,水样加标回收率为91.7～97.8％,相对标准偏差1.6～2.4％之间,分析速度150样次/小时。     

The potential of cost-effective coconut husk for the removal of toxic metal ions for environmental protection

Coconut (Cocos nucifera) husk, an agricultural waste, has been thoroughly investigated for the removal of toxic Cd(II), Cr(III) and Hg(II) ions from aqueous media. The parameters like nature and composition of electrolyte, concentration of toxic ions, dosage of coconut husk, and equilibration time between the two phases were optimized for their maximum accumulation onto the solid surface. The effect of common ions on the uptake of metal ions has been monitored under optimal conditions. The variation of retention of each metal ion with temperature was used to compute the thermodynamic quantities DeltaH, DeltaS and DeltaG. The values 18.1+/-0.6 kJmol(-1), 74+/-2 Jmol(-1)K(-1), and -3.8+/-0.04 kJmol(-1) at 298 K; 10.8+/-0.8 kJmol(-1), 48.8+/-2.7 Jmol(-1)K(-1), and -4.6+/-0.3 kJmol(-1) at 298 K; and -37.4+/-2k Jmol(-1), 105+/-7 Jmol(-1)K(-1) and -2.58+/-0.5 kJmol(-1) at 298 K were obtained for Cd(II), Cr(III) and Hg(II) ions, respectively. The sorption data were analysed by applying different sorption isotherms. The sorption capacity and energy were evaluated for each metal ion. The values of the Freundlich constants 1/n and C(m) were 0.92+/-0.04 and 52.6+/-22.2 mmolg(-1); 0.85+/-0.05 and 56.0+/-0.03 mmolg(-1); and 0.88+/-0.03 and 6.84+/-0.45 mmolg(-1) for Cd(II) Cr(III) and Hg(II) ions, respectively. Similarly, the Dubinin-Radushkevich (D-R) constants beta, X(m,) and E were evaluated for the three metal ions. To check the selectivity of the sorbent, sorption of a number of elements was measured under similar conditions. Separation of Zn(II) from Cd(II); Cr(III) from I(I), Zr(IV), Se(IV), and Hg(II) from Se(IV) and Zn(II) can be achieved using this sorbent. This cheap material has potential applications in analytical chemistry, water decontamination, industrial effluent treatment and in pollution abatement.     

含Cr（Ⅵ）废水生物处理技术及其影响因素

本文综述了微生物还原处理含价铬的废水的研究进展。讨论了影响微生物还原Cr(Ⅵ）因素包括生物体密度、初始Cr（Ⅵ）的浓度、碳源、pH、温度、溶解氧、氧化还原电位、含氧阴离子和金属离子。微生物还原Cr（Ⅵ）技术作为一种富有创新的研究应用于Cr（Ⅵ）污染的环境恢复。     

Artificial neural network based maximum power point tracking controller for photovoltaic standalone system

This article presents a two-stage maximum power point tracking (MPPT) controller using artificial neural network (ANN) for photovoltaic (PV) standalone system, under varying weather conditions of solar irradiation and module temperature. At the first-stage, the ANN algorithm locates the maximum power point (MPP) associated to solar irradiation and module temperature. Then, a simple controller at the second-step, by changing the duty cycle of a DC–DC boost converter, tracks the MPP. In this method, in addition to experimental data collection for training the ANN, a circuit is designed in MATLAB-Simulink to acquire data for whole ranges of weather condition. The whole system is simulated in Simulink. Simulation results show small transient response time, and low power oscillation in steady-state. Furthermore, dynamic response verifies that this method is very fast and precise at tracking the MPP under rapidly changing irradiation, and has very low power oscillation under slowly changing irradiation. Experimental results are provided to verify the simulation results as well.     

Assessment of the small modular reactor (SMR) marketing using modified network dynamics-based system dynamics (SD) method

Following the export success of the South Korean small modular reactor (SMR), it has been investigated for the marketing strategy of nuclear power plants (NPPs). The information feedback oriented method for the social-business matters, system dynamics (SD), is applied to the assessment of the marketing strategy in which the forecasting skills are performed. Each element has the Boolean value as 0 or 1 in which the values are selected by the random number generation. If the generated values are higher than the designed value decided by the operator, it is 1. Otherwise, it is 0. The networking based dynamical modeling is discussed. The modification of the linear networking is changed by the SD algorithm where the feedback and multiple connections are added to the original network dynamics theory. This new method has shown the complexity of the marketing strategy, especially for the NPPs.     

Retrieving surface deformation by PSInSAR™ technology: A powerful tool in reservoir monitoring

Reservoir monitoring improves our understanding of reservoir behaviour and helps achieve more effective reservoir management and prediction of future performance with obvious economic benefits. It relies on an integrated approach involving both surveillance (well or surface based; seismic, electrical, leakage, flow and deformation measurements, etc.) and modelling. Surface deformation monitoring can provide valuable constraints on the dynamic behaviour of a reservoir enabling the evaluation of volumetric changes in the reservoir through time. Levelling campaigns, tiltmeters, GPS permanent stations and Permanent Scatterer SAR Interferometry (PSInSAR™) are the techniques most widely used to determine surface displacements. Whatever the surveying technique, the detection of millimetre-level surface deformation is required to monitor small surface displacement rates that could impact risk evaluation and land use planning. Depending on depth and reservoir/overburden rheology, volumetric changes in reservoirs due to fluid extraction and injection can induce either subsidence or uplift that could trigger fault reactivation and threaten well integrity; deformation may also be detectable at the surface. Mapping surface effects accurately requires hundreds of observation points per km² which cannot be delivered by traditional monitoring methods without unacceptably large expenditure. PSInSAR™ is one of the most promising and cost-effective techniques capable of providing high precision and high areal density displacement measurements over long periods of time. Moreover, the availability of PS data for both ascending and descending orbits enables the estimation of both vertical and E–W horizontal displacement fields. Two case histories will be presented to illustrate the advantages of PSInSAR™ technology for the detection of surface deformation induced by reservoir exploitation and monitoring of its evolution though time.     

城市污水处理厂出水的化学需氧量和悬浮物的相关关系以及悬浮物测定方法探讨

以活性污泥法为基础的二级生化处理工艺是城市污水处理的基本方法，其出水的化学需氧量值(CODCr)不仅大于悬浮物(SS)值，而且两者之间还存在着一致性的相关关系。本文对这种关系作了相应探讨。同时对悬浮物的测定方法进行了探讨，提出了悬浮物的表示由可沉固体 透明度的概念。