硅藻土在环境工程领域的应用进展

综述了硅藻土在废水、废气和土壤等环境污染治理领域的研究进展和存在的问题,认为硅藻土作为一种物理化学性能优良的添加助剂,表面结构独特,吸附性能良好,对其进行改性可以适应各种需求。许多研究表明,经过改性的硅藻土对废水、废气和土壤中重金属、无机和有机污染物均具有良好的吸附或降解效果,但是大多研究都处于实验室水平,并且大多都是单因素、单污染因子的实验研究,而对多因素多污染因子的研究较少。具体应用效果还有待于实际应用的验证。     

东深供水工程生化预处理挂膜过程分析

介绍东深供水工程生化预处理挂膜启动过程中，氨氮，CODMn去除效果和填料上生物膜变化的特点。根据氨氮去除（≥50．0％），生物膜形状，生物膜上动物种类和数量可判断挂膜启动过程是否完成。本试验挂膜启动25天，比小型试验增加了10天左右，气温低是该工程挂膜启动过程时间延长的主要原因。     

缺氧——好氧生和的膜反应器挂膜的试验研究

缺氧生物膜反应器采用好氧预挂膜与快速排泥挂膜方法,在挂膜期间加强污泥回流,缩短反应器的启动时间。两种反应器内均存在呈悬浮与附着形态的污泥。     

常温厌氧流化床处理高浓度有机废水实验研究

本文对常温(25℃±3℃)条件下低密度载体厌氧流化床(AFB)反应器处理高浓度有机废水进行了研究。实验结果表明:采用好氧预挂膜快速排泥法可加快反应器的启动,低密度载体可有效降低反应器运行能耗,有机物去除效果良好。     

膜曝气生物膜反应器生物膜影响因素分析

膜曝气生物膜反应器（MABR）是一种利用透气膜进行曝气，可以实现同步硝化反硝化的污水生物处理新工艺。本文阐述了膜曝气生物反应器生物膜的原理和特点，总结了国内外在该领域的研究成果，重点介绍了C／N、氧气压力、流速、生物膜厚度、温度和pH对生物膜性能的影响。     

苏州市某水厂深度处理工艺活性炭选型试验

为筛选出适合苏州地区深度处理工艺所需的活性炭,对活性炭的吸附性能、生物膜挂膜情况以及出水浑浊度、高锰酸盐指数、TOC、UV254、氨氮、亚硝酸盐氮等水质指标进行了考察。结果表明,GAC3和GAC4活性炭在各项性能方面均优于其他活性炭。从价格上考虑,选取GAC4活性炭作为苏州市该水厂深度处理活性炭。活性炭滤池运行3个月后,对其出水进行了106项全分析,所有水质指标均能达到GB 5749-2006的要求。     

多孔沸石混合填料BAF废水脱氮及微生物研究

以天然沸石为主要原料,制备改性多孔沸石混合填料,填料柱挂膜成熟后,模拟氨氮废水及曝气生物滤池技术,经离子交换吸附、微生物再生、淋洗序批三段式运行,以考察填料的氮素去除性能,同时采用PCR-DGGE（变性梯度凝胶电泳）电泳方法表征填料生物膜的微生物特性。实验结果表明：当离子交换吸附阶段水力停留时间为3.0 h时,填料的氨氮综合去除效率最佳（82.3%～94.7%）,氮回收率较高（88.46%）;填料系统外层及上、下层的微生物群落丰富度相对更高,不同条带聚类结果与条带相似度及现实状况相符;在条带检测出可降解有机污染物的噬氢菌及硝化菌、反硝化菌。     

改性PVDF中空纤维膜处理压裂返排液研究

针对中空纤维膜应用于水力压裂返排液处理时存在的膜污染严重、通量衰减快、影响处理效率等问题,研究了PVDF固含量、凝固浴温度等因素对PVDF膜性能的影响,通过非溶剂致相分离法制备了PVDF中空纤维膜,并采用表面接枝技术,对PVDF中空纤维膜进行了表面亲水化改性。压裂返排液吸附实验结果表明,表面接枝降低了PVDF的接触角,提高了膜的亲水性。与未接枝改性的PVDF膜相比,亲水改性后的PVDF膜表面吸附的压裂返排液更少。将亲水性中空纤维膜用于页岩气水力压裂返排液的过滤处理,应用结果表明其对压裂返排液中的总铁、SS、浊度、细菌去除率达到90%以上,长时间运行后的通量保持率高,有较好的抗膜污染性。     

竹笋壳为生物膜载体的废水处理技术研究

采用室内实验装置,研究了以农业废弃物竹笋壳为反硝化碳源和生物膜载体的生物反应器对于污水中硝酸盐的去除效果,并另设以聚丙烯惰性填料球为生物膜载体的生物反应器作为对照实验。实验结果表明,以天然竹笋壳作为反硝化碳源和生物膜载体的反应器启动时间短,对污水中硝酸盐氮的去除效果较好;装置对进水DO和pH值变化有一定抗性,DO在2.0~4.0mg/L,pH值在6.8~7.2之间变化时,反应器硝酸盐的去除率变化很小,缓冲能力较强;反应器稳定性强,出水硝酸盐的去除率在80%以上。     

高效生物膜悬浮填料研究进展

悬浮填料作为一种具有发展前景的水环境治理材料,已成为当前废水处理的研究热点。本文根据大量的参考文献,综述了国内外悬浮填料的特点、种类以及悬浮填料的应用,同时对悬浮填料的发展进行了阐述。进一步开发高效、廉价和绿色的新型悬浮填料,提高填料的比表面积、空隙率和挂膜能力等核心性能参数,将促进悬浮填料生物膜工艺在我国污水治理方面更广泛的应用。     

天然硅藻土作为吸附材料处理渗滤液的效果研究

利用天然硅藻土在静态条件下对垃圾渗滤液中的氨氮和COD的吸附效果进行了研究。结果表明：天然硅藻土对于氨氮的去除效率只有14．1％；但对COD的去除效率可以达到70．1％；天然硅藻土对于COD的饱和吸附量和吸附速度明显高于其对氨氮的饱和吸附量及吸附速度；在平衡浓度相当高的情况下，每克硅藻土具有吸附65．31mg COD的极限潜力。     

Low VOC latex paints from a precipitation polymerization process

Even though paints and coatings have been very useful in protecting various substrates, their use has been accompanied by a heavy environmental price. There is a need to minimize the use of volatile organic compounds (VOCs) in the formulation of these materials. In the latex paint area, we have implemented a conventional precipitation process in emulsions to form binder particles that contain block copolymers and have softer blocks on the particle surface. The softer surface provides the binder film-forming properties without the need for the use of solvents or VOCs. The covalent connections between the soft blocks and the hard blocks are expected to impart good performance in the resulting dry coatings. Indeed, we have shown that our test coating from these binder particles containing block copolymer have similar properties in most performance categories to those of a semi-gloss control paint that has been formulated with typical amounts of VOCs.     

酸改性壳聚糖载体对漆酶的固定化

利用有机酸改性壳聚糖和交联法制备酸化壳聚糖载体,然后用改性壳聚糖载体固定漆酶。结果表明,甲酸、酒石酸改性壳聚糖的最适条件是壳聚糖与酸的量比分别为100/1(g/mol)、100/0.5(g/mol),戊二醛的浓度分别为1%、2%,缓冲溶液的pH分别为4.4、3.6,反应时间分别为3h、4.5h。两种酸改性的壳聚糖用于漆酶的固定,其酶活都有所提高,尤其用酒石酸改性的壳聚糖载体的效果最好,其酶活提高了57%。     

EMMC process for combined removal of organics, nitrogen and an odor producing substance

In order to improve the process performance regarding the removal of organics, nitrogen, and an odor-causing compound (sulfide) contained in domestic wastewater, an entrapped-mixed-microbial cell (EMMC) with and without humic substances for both fixed and moving carrier reactors and conventional suspended growth culture (i.e. conventional activated sludge process) were investigated simultaneously. Both synthetic (simulated to the organics concentration of general domestic sewage) and actual domestic wastewater were investigated under operational conditions of 12 h of hydraulic retention time (HRT) with 1 h of aeration and 1 h of non-aeration, and 6 h of HRT with continuous aeration, at a room temperature of 25 +/- 2 degrees C. It was found that entrapping humic substances in the EMMC carriers had no impact on the removal of organics, nitrogen, and the odor-producing compound. Additionally, the performance of the EMMC moving carrier system for the removal of these pollutants is similar to that of the EMMC fixed carrier system. In general, the EMMC associated systems which provide high solids retention time achieve a better removal of chemical oxygen demand (COD), nitrogen, and the odor-producing substance than the suspended growth system for both HRTs of 6 h (continuous aeration) and 12 h (1 h of aeration and 1 h of non-aeration). Both the fixed and moving carrier EMMC processes, therefore, have the potential for improvement or replacement of the existing conventional activated sludge process with regard to improving the effluent qualities (such as COD, nitrogen and odor-producing compound) for reuse/disposal.     

Mechanisms and chemistry of dye adsorption on manganese oxides-modified diatomite

The investigations into structural changes which occur during adsorbent modification and the adsorption mechanisms are essential for an effective design of adsorption systems. Manganese oxides were impregnated onto diatomite to form the type known as δ-birnessite. Initial investigations established the effectiveness of manganese oxides-modified diatomite (MOMD) to remove basic and reactive dyes from aqueous solution. The adsorption capacity of MOMD for methylene blue (MB), hydrolysed reactive black (RB) and hydrolysed reactive yellow (RY) was 320, 419, and 204 mg/g, respectively. Various analytical techniques were used to characterise the structure and the mechanisms of the dye adsorption process onto MOMD such as Fourier transform infrared (FTIR), X-ray diffraction (XRD) and atomic absorption spectrometry (A.A.). A small shift to higher values of the d-spacing of dye/MOMD was observed indicating that a small amount of the dye molecules were intercalated in the MOMD structure and other molecules were adsorbed on the external surface of MOMD. Two mechanisms of dye adsorption onto MOMD were proposed; intercalation of the dye in the octahedral layers and adsorption of the dye on the MOMD external surface. Moreover, the results demonstrated that the MOMD structure was changed upon insertion of MB and RY with an obvious decrease in the intensity of the second main peak of the MOMD X-ray pattern.     

Study of inexpensive oxygen carriers for chemical looping combustion

Norwegian industrial tailings and by-products, as well as naturally occurring minerals and ores have been surveyed with the purpose of identifying candidate oxygen carrier materials for use in a chemical looping combustion process. Nine materials, based on manganese and/or iron oxide, were selected for an initial screening test; six were deemed promising and were hence investigated further. Thermogravimetric experiments were performed to investigate the oxygen capacity, the reaction kinetics and reversibility of the oxygen absorption reaction. A manganese ore with a reversible capacity of 4.9 wt% oxygen at 1000 °C was selected as the most promising for chemical looping combustion applications. This material was modified by addition of calcia to explore the possibility of enhancing the kinetic, catalytic and mechanical properties. The addition of excess calcium relative to manganese resulted in formation of calcium manganite and related phases. The oxygen capacity of the modified material was 4.5 wt% at 1000 °C, but it has potential advantages in terms of kinetics and chemical and mechanical stability relative to the pure ore.     

Adsorption of carbon dioxide on alkali-modified zeolite 13X adsorbents

Shaped zeolite 13X adsorbent with kaolin as binder was hydrothermally modified in sodium hydroxide solution to improve its adsorption performance. The characterization of the product by XRD, N₂ adsorption–desorption and water vapour adsorption displayed that kaolin component in zeolite adsorbent can be converted into zeolite during the alkali treatment, resulting in the modified adsorbent consisting entirely of effectual adsorption composition. Compared with the unmodified adsorbent, the modified adsorbent exhibited higher adsorption capacity and uptake rate for carbon dioxide, because of the increase of effective adsorption surface and the decrease of diffusion resistance owing to conversion of kaolin binder into zeolite. The model parameters of isotherms and the isosteric heats calculated by the Clausius–Clapeyron equation for CO₂ adsorption showed the stronger interaction of adsorbate–adsorbent and the higher degree of heterogeneity of adsorption centers in modified than unmodified adsorbents.     

海泡石对亚甲基蓝的吸附性能

研究了一般海泡石、HCl改性海泡石对亚甲基蓝的吸附性能,以及在室温下的吸附动力学,计算了吸附速率常数,绘制了海泡石的吸附等温线,并求得其饱和吸附量.结果表明,室温下酸改性海泡石的吸附速率要快于一般海泡石,各类型海泡石的吸附行为符合 Langmuir 方程.     

多种复合材料固定化反应器的对比研究

选用活性炭、海砺壳2种材料作为固定化载体,对改良型UASB系统去除COD的性能进行研究,结果表明选择既高柱又循环且增加载体填充体积的系统,可有效去除高浓度有机废水的COD,但当填充载体过高时,循环系统难以实现,并存在憋气的可能。     

钻井废弃泥浆脱水工艺试验

在分析钻井废弃泥浆组成的基础上,对泥浆体系进行稀释、酸化处理,以硅改性聚合氯化铁为破胶剂,阳离子聚丙烯酰胺为絮凝剂,破坏钻井废弃泥浆的胶体体系,采用固液分离方法使泥浆液混凝脱水。试验表明:稀释倍数为4倍、pH值为5、2.5%改性聚合氯化铁为破胶剂、0.25‰阳离子聚丙烯酰胺为絮凝剂、0.8%N-626为去油剂,离心分离后泥饼中石油类含量低于3‰,混凝产生的絮体大、脱水率高、残渣稳定性好、无造浆能力。