Resources consumption and wastes emission analysis for two manufacture processes of siliconit

Silicon carbide (SiC) heating elements (siliconits) are widely used at high-temperature fields. The raw materials, manufacture process and application fields of siliconits are all related to heavy energy consumption and pollutions, and bring high environmental loads. The resources consumption and pollution emissions in siliconit manufacture process were quantificationally estimated by input/output method. Difference between two traditional techniques to produce siliconits in China was also compared and analyzed. The results show that siliconit manufacture processes consume large quantities of resources because the furnace is open to environment and too much thermal-protection materials are used. For the thick-end technique is more complicated and the thick-end siliconits have a bigger size and mass, there are more resources and energy consumptions and pollution emissions for thick-end process than that for equal-diameter process. Some suggestions were introduced to improve the traditional techniques and a new process was designed. It is the most important that the open furnace should be replaced by close vacuum furnace. Sintering and siliconizing process can be combined into one high-temperature process. As results of process simplification and vacuum sintering, resources and energy consumption and wastes emission can be decreased remarkably.     

利用EXCEL进行污水管道水力计算

EXCEL是一款非常优秀的办公自动化软件，其数字处理能力非常强大。通过推导出污水管道水力计算公式，介绍并利用EXCEL内部函数编写计算公式的程序和具体的计算方法。与手工计算的方法相比，该方法操作简单，计算结果快速、准确，非常适应于工程设计。     

HYDRAULIC FRICTION LOSS IN SMALL DIAMETER PLASTIC PIPELINES1

ABSTRACT: Although estimation of hydraulic friction loss in pipelines is one of the most frequent routine computations made by water supply engineers, almost no post-construction analysis of the accuracy of these calculations exists in the literature. This paper reports the field measured friction losses in three one-mile sections of small diameter pvc pipe which had been in service for 10 years. Hazen-Williams and Darcy-Weisbach equations are examined to provide a framework for comparing Hazen-Williams coefficients recommended by pipe manufacturers to those obtained by the field measurements. The conclusion is that the C_HW factor of 150 recommended by most pvc pipe manufacturers is too high for the diameter-velocity combinations encountered in rural dead-end small diameter lines. The measured coefficients averaged 133 which is close to that predicted by superimposing Hazen Williams coefficients on the Moody diagram from which the friction factor for the Darcy-Weisbach equation is obtained.     

中国城市污水集中处理的现状与对策研究

随着我国城市的迅速发展，城市普遍面临着水资源缺乏和水环境恶化的问题，已影响到城市的可持续发展。城市污水集中处理是解决城市水危机的有效方法，也是保护城市水环境的重要防线。分析了当前我国城市污水处理业的现状以及存在的问题，提出了加快污水处理厂技术革新，建设城市污水管网，加快城市污水回用产业化和完善污水处理厂的运营模式等解决办法，以保证我国城市实现可持续发展。     

我国油田产出水再利用技术现状及展望

随着我国油气田勘探开发力度加大和新环保法的实施,油田开采过程中耗水量大和污水处理问题是我国油气田企业面临的共同难题。从污水余热回收、污水回注、压裂液重复利用、钻井废水再利用四个方面,介绍了国内油田产出水再利用技术研究进展与应用现状,指出目前存在的污水余热再利用应用范围不广、回注污水利用不合理、化工原料未回收利用等主要问题。并通过文献调研,展望了油田污水再利用技术的发展方向,指出需从污染源头防控入手,研发更加经济环保的液体配方,并深入研究从污水中取热、取水及取化工原料的循环再利用技术,因地制宜制定相应的水质及污水配伍性实验评价标准,实现从源头至末端治理相结合的油田污水清洁生产。     

对企业实施环境保护信用等级管理的探讨——以滨州为例

为推进企业环境保护信用等级管理,滨州市环保和监察部门联合制定工作方案并向所辖县区下发文件专门部署,结合日常执法监管对市控以上企业从环保专项行动、排污情况、污染事故、治污设施、排污费和行政处罚、环境安全、建设项目、环境信访八个方面综合评定信用等级,实施有针对性的环境监督管理,有效解决了执法成本高、执法人员不足的问题,使有限的执法资源得到最合理的优化配置,进一步规范了企业环境行为,实现了引导企业自主守法和提高执法效率的双赢。     

Environmental assessment of supercritical water oxidation of sewage sludge

Environmental aspects of using supercritical water oxidation (SCWO) to treat sewage sludge were studied using a life cycle assessment (LCA) methodology. The system studied is the first commercial scale SCWO plant for sewage sludge in the world, treating sludge from the municipal wastewater treatment facility in Harlingen, TX, USA. The environmental impacts were evaluated using three specific environmental attributes: global warming potential (GWP), photo-oxidant creation potential (POCP) and resource depletion; as well as two single point indicators: EPS2000 and EcoIndicator99. The LCA results show that for the described process, gas-fired preheating of the sludge is the major contributor to environmental impacts, and emissions from generating electricity for pumping and for oxygen production are also important. Overall, SCWO processing of undigested sewage sludge is an environmentally attractive technology, particularly when heat is recovered from the process. Energy-conserving measures and recovery of excess oxygen from the SCWO process should be considered for improving the sustainability potential.     

An Experimental Study of Heat Pipe Performance Using Nanofluids

Heat pipe cooling is widely used in computer processors. Advances in microprocessor technology have resulted in reduced heat transfer surface area. Maintaining an efficient cooling process is therefore challenging. The main goal of this experimental study is to perform a parametric study on heat pipe performance using nanofluids. Nanofluids of 1 and 3 vol% of alumina nanoparticles of 20–50 nm diameters in deionized water versus deionized water as a base fluid were considered in the present study. The nanofluids are prepared in our laboratory using two-step method. The nanofluids thermal properties are measured to confirm the properties enhancement that could indicate a corresponding performance enhancement of the heat pipe. A 10 mm inner diameter, 200 mm long brass tube with 50 mm long evaporator, and 50 mm long water cooled condenser were used. Heat pipe wall temperature is reduced with nanofluids as is the temperature difference between the evaporator and condenser. The thermal diffusivity of the nanofluids is increased by 10%. The pipe pressure in case of deionized water was higher than the corresponding one for the nanofluids by 20–32%.     

Life cycle assessment of EPS and CPB inserts: design considerations and end of life scenarios

Expanded polystyrene (EPS) and corrugated paperboard (CPB) are used in many industrial applications, such as containers, shock absorbers or simply as inserts. Both materials pose two different types of environmental problems. The first is the pollution and resource consumption that occur during the production of these materials; the second is the growing landfills that arise out of the excessive disposal of these packaging materials. Life cycle assessment or LCA will be introduced in this paper as a useful tool to compare the environmental performance of both EPS and CPB throughout their life cycle stages. This paper is divided into two main parts. The first part investigates the environmental impacts of the production of EPS and CPB from 'cradle-to-gate', comparing two inserts--both the original and proposed new designs. In the second part, LCA is applied to investigate various end-of-life cases for the same materials. The study will evaluate the environmental impacts of the present waste management practices in Singapore. Several 'what-if' cases are also discussed, including various percentages of landfilling and incineration. The SimaPro LCA Version 5.0 software's Eco-indicator 99 method is used to investigate the following five environmental impact categories: climate change, acidification/eutrophication, ecotoxicity, fossil fuels and respiratory inorganics.     

The joint use of LCA and emergy evaluation for the analysis of two Italian wine farms

The aim of this paper is to evaluate two agroindustrial productive processes in their entirety (one organic and one semi-industrial), focusing on the comparison of impacts derived from the inputs and outputs of the system (life cycle assessment, LCA), integrated with a physical evaluation of the resources and natural services, on a common basis (emergy). Methods based on the joint use of LCA and emergy evaluation are useful, as they measure the contribution of environmental services and products to the productive process thus focusing primarily on the environmental impact of emissions and non-renewable energy inputs. The complementarity of the methods used in this paper contributes important elements and information useful for the comprehension of the organization of agriculture within Siena's territory. The results show important elements and useful information: (1) for the comprehension of the two agroecosystems' organization; (2) for the use of the energy flows that determine their development. Moreover, the combined use of emergy and LCA gives a comparative thermodynamic performance evaluation between organic and semi-industrial farming.     

村镇供水管网优化设计探讨

如何合理确定村镇供水管网敷设方案，关系到整个供水系统的安全性和可靠性。通过生成树变化法，将环状管网转化成树状管网，确定供水管网中最短供水路线，再计算最短供水路线下的最低综合费用、供水系统的经济管径，以确定最优管道敷设方案。根据该方法对四川省某镇供水系统进行了设计。     

From the LCA of food products to the environmental assessment of protected crops districts: a case-study in the south of Italy

In the present study, Life Cycle Assessment (LCA) methodology was applied to evaluate the energy consumption and environmental burdens associated with the production of protected crops in an agricultural district in the Mediterranean region. In this study, LCA was used as a 'support tool', to address local policies for sustainable production and consumption patterns, and to create a 'knowledge base' for environmental assessment of an extended agricultural production area. The proposed approach combines organisation-specific tools, such as Environmental Management Systems and Environmental Product Declarations, with the environmental management of the district. Questionnaires were distributed to producers to determine the life cycle of different protected crops (tomatoes, cherry tomatoes, peppers, melons and zucchinis), and obtain information on greenhouse usage (e.g. tunnel vs. pavilion). Ecoprofiles of products in the district were also estimated, to identify supply chain elements with the highest impact in terms of global energy requirements, greenhouse gas emissions, eutrophication, water consumption and waste production. These results of this study enable selection of the 'best practices' and ecodesign solutions, to reduce the environmental impact of these products. Finally, sensitivity analysis of key LCA issues was performed, to assess the variability associated with different parameters: vegetable production; water usage; fertiliser and pesticide usage; shared greenhouse use; substitution of plastics coverings; and waste recycling.     

Salt enrichment of municipal sewage: New prevention approaches in Israel

Wastewater irrigation is an environmentally sound wastewater disposal practice, but sewage is more saline than the supplied fresh water and the salts are recycled together with the water. Salts have negative environmental effects on crops, soils, and groundwater. There are no inexpensive ways to remove the salts once they enter sewage, and the prevention of sewage salt enrichment is the most immediately available solution. The body of initiatives presently structured by the Ministry of the Environment of Israel are herein described, with the aim to contribute to the search for a long-term solution of salinity problems in arid countries. The new initiatives are based on: (1) search for new technologies to reduce salt consumption and discharge into sewage; (2) different technologies to cope with different situations; (3) raising the awareness of the public and industry on the environmental implications of salinity pollution; and (4) an elastic legal approach expressed through new state-of-the-art regulations. The main contributor to the salinity of sewage in Israel is the watersoftening process followed by the meat koshering process. Some of the adopted technical solutions are: the discharge of the brine into the sea, the substitution of sodium by potassium salts in the ion-exchangers, the construction of centralized systems for the supply of soft water in industrial areas, the precipitation of Ca and Mg in the effluents from ion-exchangers and recycling of the NaCI solution, a reduction of the discharge of salts by the meat koshering process, and new membrane technology for salt recovery.     

Effect of pipes in heat pump system on electric vehicle energy saving

ABSTRACT

Refrigerant pressure drop and temperature change in pipes are normally ignored in the thermodynamic analysis of traditional vehicle air conditioning system, this will result in serious errors. In this Paper, pressure drop and temperature difference are simulated in different pipes of electric vehicle (EV) heat pump system to analysis the effects of pipes in the actual EV heat pump system. The results indicate that the greater the mass flow, the faster pressure drop increases, the temperature difference decreases. Pressure drop of saturated liquid refrigerant is smaller than that of saturated gas refrigerant at the same saturation pressure and mass flow rate. The higher the refrigerant pressure (no phase change), the slower pressure drop decreases, the faster the temperature difference decreases. Pressure drop decreases with the increment of bending angle of the pipe. For EV heat pump system, suitable valves and less branches are helpful for energy saving of the system. Shortening the pipe between compressor and condenser can reduce temperature change obviously. Pressure drop per unit length in the pipe between evaporator and compressor is large especially in heating mode because of lower refrigerant density. It even reaches to over 100 times of that in the pipe between condenser and throttle valve in heating mode and has negative effects on the performance of the system. If the evaporator is closer to the compressor and the number of branches is less, then pressure drop will decrease a lot, which will be advantageous for energy saving of the heat pump system.     

实施注采一体管柱技术 节能降耗减污增效

超稠油蒸汽吞吐注采一体管柱技术,是对多项稠油开采工艺技术进行实践、总结、分析而来。该项技术,解决了作业频繁的问题,实现了不动管柱直接转抽,并可以多次注汽、转抽;由此而改变传统的蒸汽吞吐注采工艺技术,做到注、采、焖、放一体管柱,减少作业工序和降低井筒热损失,降低环境污染及电能消耗,实现超稠油不动管柱开采,有效降低超稠油开采成本,提高了油井的生产实效,并取得可观的经济效益和环境效益,实现节能、降耗、减污、增效的清洁生产目标。     

ECONOMIC APPRAISAL OF A GROUND WATER DEVELOPMENT PROJECT1

A ground water development project in the northern part of Thailand was appraised by means of benefit-cost analysis. This is the first project in Thailand to develop ground water for irrigation purposes and it is also the first project which made use of an underground PVC pipe water distribution system. Results indicate that the project is economically feasible. In comparing different water distribution systems, it is also found that distribution by means of underground PVC pipes is more economical compared to an open ditch system if the life of the latter is relatively short and the rates of inflation are high.     

利用污水管道处理生活污水试验研究

本文针对污水管道系统管径大，距离长，污水在当中输送时间长等特点和环境污染现状，提出充分利用污水管道巨大空间的如下设想；采用前置高负荷生物接触氧化渠和在沿途的污水提升泵站中注入空气的管道生化反应工艺，从而有机污染物质在输送过程中得到部分降解，并且进行了模拟试验和研究。     

Life cycle analysis (LCA) for the incorporation of rice husk ash in mortar coating

Considering that the civil construction segment is responsible for a significant amount of the environmental impact, once it consumes a large amount of natural resources and energy, the incorporation of waste in the process brings sustainable benefits for the companies as well as for society. In addition, the reduction of the useful life of mortar coating related to the lack of adherence to the substrate provokes a large generation of waste, increasing the environmental liability of the respective industry. This study aimed to determine the technical and environmental viability of the incorporation of rice husk ash (RHA) waste in mortar coatings, in order to reduce the consumption of natural resources and improve the conditions of adherence of the cementitious matrix. For this evaluation, mechanical tests were carried out to test the adherence to the substrate, besides a survey of all the processes related to mortar coating production, from natural resources extraction till the application of the product and its consequent impact. Finally it was used the life cycle analysis (LCA) tool to evaluate the environmental issue. The results showed an increase of 100% of bond strength for the mortars with 5% addition of RHA, and it was identified, among the processes surveyed, a smaller number of significant impacts in relation to the mortar with no addition. It is noticed that, for the conditions of this study, the mortars with RHA addition present better technical and environmental performance compared to the usual mortars.     

生物滤池—PE管微孔压滤技术治理中药废水

应用ＰＥ管微孔压滤技术，并辅以自然沉降、曝气、生物滤池等技术手段治理中药废水，出水达ＧＢ８９７８－８８中的一级排放标准，并回收了约７０％的水资源，文中的油污给ＰＥ管微孔压液技术带来的影响作了介绍。     

Practical life cycle assessment through streamlining

Life cycle assessment (LCA) provides a concept, framework, and method to identify and evaluate the environmental burdens of products and processes. An ongoing concern of companies trying to implement LCA is the value of LCA in supporting actual decisions versus the resources and time needed to conduct a “full” LCA. In response to these concerns, there has been a lot of activity surrounding the “streamlining” of LCA to keep it more manageable yet provide useful and acceptably accurate results. This article explores the concept of streamlining, discusses where and how streamlining decisions can be made in an LCA, and presents issues related to conducting more streamlined LCAs. Due to the wide variety of purposes and scenarios in which LCAs are conducted, it is difficult to devise a one-size-fits-all method for streamlining. Instead, we have focused on presenting the streamlining options in the context of major decision points that are common to most LCAs.