采油系统硫化氢治理技术探索

文章提出一种针对油田采油系统由于井筒原生和地面集输系统次生造成硫化氢污染的综合治理技术,研究形成了集输系统次生硫化氢外源微生物抑制硫酸盐还原菌技术,实现对次生硫化氢的生物抑制。该技术能使油井硫化氢降至5mg/m3,集输系统次生硫化氢降至25mg/m3以下,改善了原油集输系统作业场所工作环境,消除了硫化氢气体对人体危害的安全隐患。     

微生物燃料电池在污水处理中的研究进展

微生物燃料电池（Microbial Fuelcell，MFC）是一种以微生物为催化剂，将有机物中的化学能转化为电能的装置。本文介绍了微生物燃料电池的原理和特点，阐述了反应器结构、底物种类、电极等方面的研究进展，分析了微生物燃料电池未来的发展方向，并对今后的研究提出建议。     

Shift to continuous operation of an air-cathode microbial fuel cell long-running in fed-batch mode boosts power generation

Microbial fuel cells (MFCs) which are operated in continuous mode are more suitable for practical applications than fed batch ones. The aim of the present study was to characterize an air-cathode MFC operating in continuous mode and to determine the intrinsic properties for suitable performance and scalability. Air-cathode MFCs were constructed from plexiglass with a total working volume of 220 mL. Zirfon® separator used in this MFC had cross section area of 100 cm². The air cathode MFCs were operated in fed-batch mode and then shifted to the continuous mode. To determine the behavior of anode and cathode in long term operation (274 days), their contribution in MFC performance was evaluated over time. Once the active biofilm was formed, power production and substrate consumption rate were significantly higher. The internal resistance increased with the passage of time. After stabilization of biofilm when the MFC was placed in close circuit by connecting an external resistance, the anode-reference and cathode-reference electrode behavior showed that anode potential is near to the bacterial cell inside potential. The maximum open circuit voltage achieved was 623 mV and the highest power and volumetric power density were 38.03 mW/m² and 1296 mW/m³, respectively.     

硫酸盐废水处理产电过程中的电子分流机制研究

为探讨废水中硫酸盐对微生物燃料电池（MFC）产电效能的影响,采用单室空气阴极MFC反应器处理模拟硫酸盐废水,并对硫酸盐的电子分流过程进行了监测。结果表明,在一定范围内,提高硫酸盐浓度能使MFC的稳定电压上升,电池持续时间延长,MFC输出功率增大。随着进水硫酸盐浓度提高,微生物产生的电子总量中,硫酸盐还原捕获的电子和通过外电路的电子所占的比例均下降,分别由12．54％和31．45％下降至7_32％和8．49％。研究表明,较低浓度硫酸盐能够提高MFC的电能输出功率,但由于硫酸盐的还原将消耗掉大量电子,进而降低MFC的库伦效率。     

Determination of effects of turbulence flow in a cathode environment on electricity generation using a tidal mud-based cylindrical-type sediment microbial fuel cell

We examined the possibility of harvesting electricity from the surface of a tidal mud flat using a cylindrical-type sediment microbial fuel cell (SMFC), a marine mud battery (MMB), which can be applied in a sea environment where the ebb and flow occur due to tidal difference. In addition, we indirectly investigated the influence of ebb and flow in a lab, using aeration, argon gassing, and by agitating the cathodic solution. The MMBs consisted of cylindrical acrylic compartments containing a nylon membrane, an anode, and a cathode in a single body. The MMBs were stuck vertically into an artificial tidal mud flat such that the anode electrode was in direct contact with the tidal mud surface. As a result, the maximum current and power density generated were 35 mA/m² and 9 mW/m², respectively, thus verifying that it is possible to harvest electricity from the surface of a tidal mud flat using an MMB without burying the anode electrode in the tidal mud. Furthermore, the results of tests using an artificial turbulence flow showed the flow induced by the tidal ebb and flow could allow the performance of MMBs to be enhanced.     

Tracing sources of sulfur in the Florida Everglades

We examined concentrations and sulfur isotopic ratios (34S/32S, expressed as delta34S in parts per thousand [/1000] units) of sulfate in surface water, ground water, and rain water from sites throughout the northern Everglades to establish the sources of sulfur to the ecosystem. The geochemistry of sulfur is of particular interest in the Everglades because of its link, through processes mediated by sulfate-reducing bacteria, to the production of toxic methylmercury in this wetland ecosystem. Methylmercury, a neurotoxin that is bioaccumulated, has been found in high concentrations in freshwater fish from the Everglades, and poses a potential threat to fish-eating wildlife and to human health through fish consumption. Results show that surface water in large portions of the Everglades is heavily contaminated with sulfate, with the highest concentrations observed in canals and marsh areas receiving canal discharge. Spatial patterns in the range of concentrations and delta34S values of sulfate in surface water indicate that the major source of sulfate in sulfur-contaminated marshes is water from canals draining the Everglades Agricultural Area. Shallow ground water underlying the Everglades and rain water samples had much lower sulfate concentrations and delta34S values distinct from those found in surface water. The delta34S results implicate agricultural fertilizer as a major contributor to the sulfate contaminating the Everglades, but ground water under the Everglades Agricultural Area (EAA) may also be a contributing source. The contamination of the northern Everglades with sulfate from canal discharge may be a key factor in controlling the distribution and extent of methylmercury production in the Everglades.     

Nutrient conversions by photosynthetic bacteria in a concentrated animal feeding operation lagoon system

A diurnal examination was conducted to determine the effect of photosynthetic bacteria on nutrient conversions in a two-stage concentrated animal feeding operation (CAFO) lagoon system in west-central Oklahoma. Changes in nutrients, microbial populations, and physical parameters were examined at three depths (0, 1.5, and 3.0 m) every 3 h over a 36-h period. The south lagoon (SL) was anaerobic (dissolved oxygen [DO] = 0.09 +/- 0.12 mg/L) while the north lagoon (NL) was facultative (DO ranged from 4.0-0.1 mg/L over 36-h period). Negative sulfide-sulfate (-0.85) and bacteriochlorophyll a (bchl a)-sulfate (-0.83) correlations, as well as positive bchl a-sulfide (0.87) and light intensity (I)-bchl a (0.89) correlations revealed that the SL was dominated by sulfur conversions driven by the photosynthetic purple sulfur bacteria (PSB). The correlation data was supported by diurnal trends for sulfate, sulfide, and bchl a. Both nitrogen and sulfur conversions played a role in the NL; however, nitrogen conversions appeared to dominate this system because of the activity of cyanobacteria. This was shown by positive chlorophyll a (chl a)-I (0.91) and chl a-nitrate (0.98) correlations and the negative correlation between ammonium and nitrite (-0.88). Correlation data was further supported by diurnal trends observed for chl a, DO, and ammonium. For both lagoons, the dominant photosynthetic microbial species determined which nutrient conversion processes were most important.     

Mesocosm-scale evaluation of faunal and microbial communities of aerated and unaerated leachfield soil

Aeration improves the capacity of leachfields to decontaminate and reduce the nutrient load of wastewater. To gain a better understanding of the effects of aeration, we examined the faunal and microbial communities of septic system leachfield soil (0-4 and 4-13 cm) using replicated (n = 3) mesocosms that were actively aerated (AIR) or unaerated (LEACH). Protozoa were 40 to 140 times more abundant in AIR than in LEACH soil. No nematodes were found in LEACH soil, whereas AIR soil contained 5 to 14 x 10(3) nematodes (all bacteriovores) kg(-1). Active microbial biomass was four to five times higher in AIR than LEACH soil. Proteobacteria and actinomycetes/sulfate-reducing bacteria constituted a higher proportion of the community in AIR soil, whereas anaerobic Gram-negative bacteria/firmicutes were more prominent in LEACH soil. Ratios of prokaryotic to eukaryotic phospholipid fatty acids (PLFAs) were higher in LEACH soil, as were membrane stress index values, whereas the starvation index was higher in AIR soil. Community-level physiological profiles showed that 29 and 30 different substrates were used for growth by LEACH and AIR soil microorganisms, respectively. The AIR soil had more microorganisms capable of growing on 10 substrates, whereas growth on two substrates was higher in LEACH soil. Polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) analysis of 16S rRNA gene fragments revealed greater diversity of dominant phylotypes in AIR than LEACH soil, with communities separated by treatment. Aerated leachfield soil had a larger and more diverse faunal and microbial community than unaerated soil, possibly due to differences in the type and availability of electron acceptors.     

Effect of sulfate on the simultaneous bioreduction of iron and uranium

The biogeochemistry related to iron- and sulfate-reducing conditions influences the fate of contaminants such as petroleum hydrocarbons, trace metals, and radionuclides (i.e., uranium) released into the subsurface. An understanding of these processes is imperative to successfully predict the fate of contaminants during bioremediation scenarios. A series of flow-through sediment column experiments were performed to determine if the commencement of sulfate-reducing conditions would occur while bioavailable Fe(III) was present and to determine how the bioreduction of a contaminant (uranium) was affected by the switch from iron-dominated to sulfate-dominated reducing conditions. The results presented herein demonstrated that, under biostimulation, sulfate reduction can commence even though a significant pool of bioavailable Fe(III) is present. In addition, the rate of U(VI) reduction was not negatively affected by the commencement of sulfate-reducing conditions.     

Cloning and expression of α-amylase in E. coli: genesis of a superior biocatalyst for substrate-specific MFC

One of the most practical approaches for establishing a successful microbial fuel cell (MFC) is to fasten the oxidation rate of the substrate by the microorganisms to get quick paced electron transfer between microbes and electrode. A genetically modified Escherichiacoli, overexpressing α-amylase, is constructed and applied as biocatalyst in MFC using starch as substrate. The results are compared with nonrecombinant, native E.coli. The results show better performance for the MFC containing the recombinant strain demonstrated by higher power density (PD), lower resistance, and significant electrochemical activity. Maximum PD has been recorded as 279.04 mW m^?2 compared to 120.33 Mw m^?2 for the MFC operated with nonrecombinant E.coli. The impedance results also suggest the effectiveness of the recombinant strain by lowering the internal resistance by more than half order as compared to the nonrecombinant one. These results affirm that the engineered strain can be used as a superior biocatalyst in contrast to the native strain and by using the technique of genetic alteration; gene of interest can be inserted based on the substrate to be treated. So, this work gives a useful insight for accomplishing successful MFC operation with the use of bacterial stains engineered at the molecular level.     

Effects of cattle slurry acidification on ammonia and methane evolution during storage

Slurry acidification before storage is known to reduce NH(3) emissions, but recent observations have indicated that CH(4) emissions are also reduced. We investigated the evolution of CH(4) from fresh and aged cattle slurry during 3 mo of storage as influenced by pH adjustment to 5.5 with sulfuric acid. In a third storage experiment, cattle slurry acidified with commercial equipment on two farms was incubated. In the manipulation experiments, effects of acid and sulfate were distinguished by adding hydrochloric acid and potassium sulfate separately or in combination, rather than sulfuric acid. In one experiment sulfur was also added to slurry as the amino acid methionine in separate treatments. In each treatment 20-kg portions of slurry (n = 4) were stored for 95 d. All samples were subsampled nine to 10 times for determination of NH(3) and CH(4) evolution rates using a 2-L flow-through system. In all experiments, the pH of acidified cattle slurry increased gradually to between 6.5 and 7. Acidification of slurry reduced the evolution of CH(4) by 67 to 87%. The greatest reduction was observed with aged cattle slurry, which had a much higher potential for CH(4) production than fresh slurry. Sulfate and methionine amendment to cattle slurry without pH adjustment also significantly inhibited methanogenesis, probably as a result of sulfide production. The study suggests that complex microbial interactions involving sulfur transformations and pH determine the potential for CH(4) emission during storage of cattle slurry, and that slurry acidification may be a cost-effective greenhouse gas mitigation option.     

塔中油田硫酸盐还原菌恶性繁殖机理分析＊

硫酸盐还原菌等的恶性繁殖使油田生产管线设施腐蚀破坏、结垢堵塞,注入地层后对油层造成伤害。研究发现,塔中油田联合站水体可检测SRB菌数高达2.5×104个/mL,注水管垢含FeS高达29.8%,属硫酸盐还原菌恶性繁殖代谢产物。塔中油田水系统各主要环节中硫酸盐还原菌和硫化氢含量与油田水处理工艺特点密切相关,其中塔中油田联合站完全密闭的水处理压力流程是造成该站硫酸盐还原菌恶性繁殖的主要原因。实验表明,前端适度曝氧、添加H2O2等氧化性杀菌剂和300mg/L冲击式加药等都是抑制硫酸盐还原菌的有效方法。     

Effect of culture time on the growth curve and power performance in a microbial fuel cell at a fixed amount of liquid culture

The microbial fuel cell uses the microorganism biochemistry to carry on the energy conversion. Concerning the experimental precision, the colony culture would be replaced by a fixed amount of liquid culture for Microbial fuel cell of Escherichia coli. The anode and cathode chambers whose each volume is 100 mL were utilized, the effective surface area of proton exchange membrane Nafion-117 is about 9 cm². In addition, the electrode area of carbon cloth is 20 cm². Three kinds of Escherichia coli, named as BCRC No. 10322, 10675 and 51534, respectively, would be selected. Results show that the electricity performance of Escherichia coli of BCRC No.51534 is better than the other microorganism studied because of having a larger open circuit voltage of 1.01 V and limiting current 22 mA, the maximum power density of 1342 mW/m^2, and average working power density of 295 mW/m² would be produced. These results would be useful to improve the performance of microbial fuel cell.     

浸矿微生物胞外聚合物研究进展

浸矿微生物的胞外聚合物因其在细菌和矿物界面之间的重要作用而成为生物湿法冶金研究的热点。目前,浸矿微生物EPS研究集中在不同营养条件下的EPS组分分析、EPS合成途径和EPS对硫化矿物的生物作用过程等方面。详细归纳并总结了浸矿微生物胞外聚合物研究的最新进展,并指出未来的发展方向。     

Passive treatment of acid mine drainage in bioreactors using sulfate-reducing bacteria: critical review and research needs

Acid mine drainage (AMD), characterized by low pH and high concentrations of sulfate and heavy metals, is an important and widespread environmental problem related to the mining industry. Sulfate-reducing passive bioreactors have received much attention lately as promising biotechnologies for AMD treatment. They offer advantages such as high metal removal at low pH, stable sludge, very low operation costs, and minimal energy consumption. Sulfide precipitation is the desired mechanism of contaminant removal; however, many mechanisms including adsorption and precipitation of metal carbonates and hydroxides occur in passive bioreactors. The efficiency of sulfate-reducing passive bioreactors is sometimes limited because they rely on the activity of an anaerobic microflora [including sulfate-reducing bacteria (SRB)] which is controlled primarily by the reactive mixture composition. The most important mixture component is the organic carbon source. The performance of field bioreactors can also be limited by AMD load and metal toxicity. Several studies conducted to find the best mixture of natural organic substrates for SRB are reviewed. Moreover, critical parameters for design and long-term operation are discussed. Additional work needs to be done to properly assess the long-term efficiency of reactive mixtures and the metal removal mechanisms. Furthermore, metal speciation and ecotoxicological assessment of treated effluent from on-site passive bioreactors have yet to be performed.     

Natural alkalinity generation in neutral lakes affected by acid mine drainage

Lakes in surface mining areas are often subject to continuous loads of acid mine drainage. The knowledge of internal alkalinity generation in a lake is necessary to predict if the lake will stay circumneutral or may acidify. The most important processes of alkalinity production in lakes are sulfate reduction, denitrification, and the burial of N in the sediment. By summarizing data from the literature, we present probable rates of these different processes in circumneutral mining lakes. The critical acidity load that can probably be compensated for by internal processes, is 5.09 mmol(-) m(-2) d(-1) in productive lakes and 0.50 mmol(-) m(-2) d(-1) in less productive lakes. Under the assumption that methanogenesis is inhibited by high sulfate concentrations, the highest probable acidity loads in such lakes are 6.85 mmol(-) m(-2) d(-1) and 1.06 mmol(-) m(-2) d(-1), respectively. Denitrification, sulfate reduction, and N burial contributed significantly to total alkalinity production. Sulfate reduction had the largest potential. However, existing models cannot predict alkalinity generation from sulfate concentrations alone because the long-term stability of reduced S compounds in the sediment is crucial for a sustainable biological alkalinity generation. The larger acid-neutralizing potential of higher trophic lakes is caused both by higher rates of microbial activity and by a greater stability of reduced reaction products in the sediment. The largest uncertainties in our knowledge with respect to the total alkalinity budget are related to microbial processes in sulfate-rich freshwater lakes and the long-term stability of reduced reaction products in the sediment.     

Enhanced biogeochemical cycling and subsequent reduction of hydraulic conductivity associated with soil-layer interfaces in the vadose zone

Biogeochemical dynamics in the vadose zone are poorly understood due to the transient nature of chemical and hydrologic conditions but are nonetheless critical to understanding chemical fate and transport. This study explored the effects of a soil layer on linked geochemical, hydrological, and microbiological processes. Three laboratory soil columns were constructed: a homogenized medium-grained sand, a homogenized organic-rich loam, and a sand-over-loam layered column. Upward and downward infiltration of water was evaluated during experiments to simulate rising water table and rainfall events, respectively. In situ collocated probes measured soil water content, matric potential, and Eh. Water samples collected from the same locations were analyzed for Br, Cl, NO, SO, NH, Fe, and total sulfide. Compared with homogeneous columns, the presence of a soil layer altered the biogeochemistry and water flow of the system considerably. Enhanced biogeochemical cycling was observed in the layered column over the texturally homogeneous soil columns. Enumerations of iron- and sulfate-reducing bacteria showed 1 to 2 orders of magnitude greater community numbers in the layered column. Mineral and soil aggregate composites were most abundant near the soil-layer interface, the presence of which likely contributed to an observed order-of-magnitude decrease in hydraulic conductivity. These findings show that quantifying coupled hydrologic-biogeochemical processes occurring at small-scale soil interfaces is critical to accurately describing and predicting chemical changes at the larger system scale. These findings also provide justification for considering soil layering in contaminant fate and transport models because of its potential to increase biodegradation or to slow the rate of transport of contaminants.     

Metal bioavailability and speciation in a wetland tailings repository amended with biosolids compost,wood ash,and sulfate

Lead poisoning of waterfowl from direct ingestion of wetland mine tailings has been reported at the Coeur d'Alene River basin in Idaho. A greenhouse study was conducted to evaluate the effects of surface applications of amendments on lead bioavailability in the tailings. Treatments included sediment only, and sediment with three different surface amendments: (i) biosolids compost plus wood ash, (ii) compost + wood ash + a low SO4(2-) addition as K2SO4, and (iii) compost + wood ash + a high SO4(2-) addition. Measured variables included growth and tissue Pb, Zn, and Cd concentration of arrowhead (Sagittaria latifolia Willd.) and cattail (Typha latifolia L.) and soil pH, redox potential (Eh), pore water Pb, Pb speciation by X-ray absorption spectroscopy, and in vitro Pb bioavailability. The compost + ash amendment alleviated phytotoxicity for both plant species. Bioavailability of Pb as measured by a rapid in vitro extract decreased by 24 to 34% (over control) in the tailings directly below the amendment layer in the compost + SO4 treatments. The ratio of acid volatile sulfide (AVS) to simultaneously extracted metals (SEM) also indicated a reduction in Pb bioavailability (1:40 control, 1:20 compost, 1:8 compost + low SO4, and 1:3 compost + high SO4). Extended X-ray adsorption fine structure (EXAFS) and X-ray absorption near edge structure (XANES) spectroscopy data indicated that lead sulfide was greater after 99 d in the treatments that included additions of sulfate. These results indicated that, under reducing conditions, surface amendments of compost + wood ash (with or without sulfate) decreased the bioavailability of Pb in metal-contaminated mine tailings.     

The living banana plant as a long-lasting battery cell

Among citrus fruits, lemon is widely used as a low-power electrical source. Although, it can generate a potential difference, this phenomenon is only sustainable for few days, and no other alternative organism has been reported to provide a similar potential with longer duration. This study reports the discovery of living banana plant as an inexpensive, reliable, stable, and long-lasting power. A Zn anode and Cu cathode are inserted into banana plant to extract electricity, and the organic compounds of plant act as electrolyte. This new discovery may introduce an era of providing renewable energy to who live in proximity to banana plantations.     

Investigation of titanium liquid/gas diffusion layers in proton exchange membrane electrolyzer cells

In a proton exchange membrane electrolyzer cell (PEMEC), liquid/gas diffusion layer (LGDL) is expected to transport electrons, heat, and reactants/products to and from the catalyst layer with minimum voltage, current, thermal, interfacial, and fluidic losses. In addition, carbon materials, which are typically used in PEM fuel cells (PEMFCs), are unsuitable in PEMECs due to the high ohmic potential and highly oxidative environment of the oxygen electrode. In this study, a set of titanium gas diffusion layers with different thicknesses and porosities are designed and examined coupled with the development of a robust titanium bipolar plate. It has been found that the performance of electrolyzer improves along with a decrease in thickness or porosity of the anode LGDL of titanium woven meshes. The ohmic resistance of anode LGDL and contact resistance between anode LGDL and the anode catalyst play dominant roles in electrolyzer performance, and better performance can be obtained by reducing ohmic resistance. Thin titanium LGDLs with straight-through pores and optimal pore morphologies are recommended for the future developments of low-cost LGDLs with minimum ohmic/transport losses.