Influence of water treatment residuals on phosphorus solubility and leaching

Laboratory and greenhouse studies compared the ability of water treatment residuals (WTRs) to alter P solubility and leaching in Immokalee sandy soil (sandy, siliceous, hyperthermic Arenic Alaquod) amended with biosolids and triple superphosphate (TSP). Aluminum sulfate (Al-WTR) and ferric sulfate (Fe-WTR) coagulation residuals, a lime softening residual (Ca-WTR) produced during hardness removal, and pure hematite were examined. In equilibration studies, the ability to reduce soluble P followed the order Al-WTR > Ca-WTR = Fe-WTR > hematite. Differences in the P-fixing capacity of the sesquioxide-dominated materials (Al-WTR, Fe-WTR, hematite) were attributed to their varying reactive Fe- and Al-hydrous oxide contents as measured by oxalate extraction. Leachate P was monitored from greenhouse columns where bahiagrass (Paspalum notatum Flugge) was grown on Immokalee soil amended with biosolids or TSP at an equivalent rate of 224 kg P ha(-1) and WTRs at 2.5% (56 Mg ha(-1)). In the absence of WTRs, 21% of TSP and 11% of Largo cake biosolids total phosphorus (PT) leached over 4 mo. With co-applied WTRs, losses from TSP columns were reduced to 3.5% (Fe-WTR), 2.5% (Ca-WTR), and <1% (Al-WTR) of applied P. For the Largo biosolids treatments all WTRs retarded downward P flux such that leachate P was not statistically different than for control (soil only) columns. The phosphorus saturation index (PSI = [Pox]/ [Al(ox) + Fe(ox)], where Pox, Al, and Fe(ox) are oxalate-extractable P, Al, and Fe, respectively) based on a simple oxalate extraction of the WTR and biosolids is potentially useful for determining WTR application rates for controlled reduction of P in drainage when biosolids are applied to low P-sorbing soils.     

Evaluating phosphorus loss from a Florida spodosol as affected by phosphorus-source application methods

Incorporating applied phosphorus (P) sources can reduce P runoff losses and is a recommended best management practice. However, in soils with low P retention capacities, leaching can be a major mechanism for off-site P loss, and the P-source application method (surface or incorporation) may not significantly affect the total amount of off-site P loss. We utilized simulated rainfall protocols to investigate effects of P-source characteristics and application methods on the forms and amounts of P losses from six P sources, including five biosolids materials produced and/or marketed in Florida, and one inorganic fertilizer (triple superphosphate). A typical Florida Spodosol (Immokalee fine sand; sandy, siliceous, hyperthermic Arenic Alaquods) was used for the study, to which the P sources were each applied at a rate of 224 kg P ha(-1) (approximately the P rate associated with N-based biosolids applications). The P sources were either surface-applied to the soil or incorporated into the soil to a depth of 5 cm. Amended soils were subjected to three simulated rainfall events, at 1-d intervals. Runoff and leachate were collected after each rainfall event and analyzed for P losses in the form of soluble reactive P (SRP), total dissolved P (TDP), total P (TP), and bioavailable P (BAP) (in runoff only). Cumulative masses (runoff + leachate for the three rainfall events) of P losses from all the P sources were similar, whether the amendments were surface-applied or incorporated into the soil. The solubility of the amendment, rather than application method, largely determines the P loss potential in poorly P-sorbing Florida Spodosols.     

Runoff and leachate losses of phosphorus in a sandy Spodosol amended with biosolids

Florida Spodosols are sandy, inherently low in Fe- and Al-based minerals, and sorb phosphorus (P) poorly. We evaluated runoff and leachate P losses from a typical Florida Spodosol amended with biosolids and triple superphosphate (TSP). Phosphorus losses were evaluated with traditional indoor rainfall simulations but used a double-deck box arrangement that allowed leaching and runoff to be determined simultaneously. Biosolids (Lakeland, OCUD, Milorganite, and Disney) represented contrasting values of total P, percent water-extractable P (PWEP), and percentage of solids. All P sources were surface applied at 224 kg P ha(-1), representing a soil P rate typical of N-based biosolids application. All biosolids-P sources lost less P than TSP, and leachate-P losses generally dominated. For Lakeland-amended soil, bioavailable P (BAP) was mainly lost by runoff (81% of total BAP losses). This behavior was due to surface sealing and drying after application of the slurry (31 g kg(-1) solids) material. For all other P sources, BAP losses in leachate were much greater than in runoff, representing 94% of total BAP losses for TSP, 80% for Milorganite, 72% for Disney, and 69% for OCUD treatments. Phosphorus leaching can be extreme and represents a great concern in many coarse-textured Florida Spodosols and other coastal plain soils with low P-sorption capacities. The PWEP values of P sources were significantly correlated with total P and BAP losses in runoff and leachate. The PWEP of a source can serve as a good indicator of potential P loss when amended to sandy soils with low P-retention capacities.     

Biosolids effects on phosphorus retention and release in some sandy Florida soils

The soil solid phase components most responsible for P sorption in Florida soils are Fe and Al oxides. Thus, we hypothesized that land application of biosolids would significantly increase a soil's P retention by increasing its content of P-sorbing solids, especially when biosolids with high Fe and Al concentrations are applied to soils that sorb P poorly. Biosolids effects were quantified by a series of single-point isotherms on soils from two field studies sampled for up to 4 yr after initial biosolids application. Biosolids additions had little effect on P retention in a soil with abundant oxalate-extractable Fe and Al and a correspondingly large native P-sorbing capacity. However, biosolids significantly increased P retention in a soil with low oxalate-extractable Fe and Al content and low native P-sorbing capacity. Biosolids effects on P retention lasted 1 to 3 yr after application, depending on biosolids source and rate of application, and generally mimicked persistence of increased extractable Fe and Al concentrations in the poorly P-sorbing soil. Disappearance of added Fe and Al (and, hence, P retention capacity) from the surface horizons over time was relatively rapid, perhaps due to abundant organic acid production associated with biosolids degradation. Phosphorus in biosolids containing (or tailored to contain) abundant Fe and/or Al can be expected to behave as a slowly available P source, and to be less subject to leaching losses than completely soluble P sources.     

Surface applied water treatment residuals affect bioavailable phosphorus losses in Florida sands

Water treatment residuals (WTR) can reduce runoff P loss and surface co-application of P-sources and WTR is a practical way of land applying the residuals. In a rainfall simulation study, we evaluated the effects of surface co-applied P-sources and an Al-WTR on runoff and leacheate bioavailable P (BAP) losses from a Florida sand. Four P-sources, namely poultry manure, Boca Raton biosolids (high water-soluble P), Pompano biosolids (moderate water-soluble P), and triple super phosphate (TSP) were surface applied at 56 and 224kgPha(-1) (by weight) to represent low and high soil P loads typical of P- and N-based amendments rates. The treatments further received surface applied WTR at 0 or 10gWTRkg(-1) soil. BAP loss masses were greater in leachate (16.4-536mg) than in runoff (0.91-46mg), but were reduced in runoff and leachate by surface applied WTR. Masses of total BAP lost in the presence of surface applied WTR were less than approximately 75% of BAP losses in the absence of WTR. Total BAP losses from each of the organic sources applied at N-based rates were not greater than P loss from TSP applied at a P-based rate. The BAP loss at the N-based rate of moderate water-soluble P-source (Pompano biosolids) was not greater than BAP losses at the P-based rates of other organic sources tested. The hazards of excess P from applying organic P-sources at N-based rates are not greater than observed at P-based rates of mineral fertilizer. Results suggest that management of the environmental P hazards associated with N-based rates of organic materials in Florida sands is possible by either applying P-sources with WTR or using a moderate water-soluble P-source.     

Phosphorus release from a biosolids-amended sandy spodosol

Most regulations governing biosolids land application do not consider that phosphorus (P) solubility can vary widely among biosolids. Current regulations typically group all biosolids together in one category or group biosolids together with manures. Research has shown that not all biosolids have the same potential to affect the environment when land applied, but the database is limited. The purpose of this study was to characterize P release from several biosolids produced and/or marketed in Florida. A small soil column dynamic laboratory incubation was conducted to assess P release potential. Eleven biosolids and a mineral fertilizer (triple super phosphate) were individually mixed with a typical low-P sorbing Florida soil (Immokalee fine sand) at 56 and 224 kg P ha(-1). Columns were periodically leached over 5.5 mo to attain 60 mL (1/2 pore volume) of drainage in each leaching. Soluble reactive P was determined and summed over the eight leachings to represent total P source release. Cumulative P release (as a percentage of P applied) was greatest from biological P removal (BPR) and BPR-like biosolids and least from heat-dried materials. Phosphorus release from biosolids depends on biosolids treatment type (digestion) and P chemistry, suggesting that biosolids regulations must account for differences in P lability to accurately gauge environmental risk.     

Phytoavailability of biosolids phosphorus

Efficient utilization of biosolids P for agronomic purposes requires accounting for differences in the phytoavailability of P in various biosolids. Greenhouse studies were conducted with a common pasture grass grown in two P-deficient soils amended with 12 biosolids and a commercial fertilizer (triple superphosphate, TSP) to quantify P uptake and to assess the relative phytoavailabilities of the P sources. Biosolids were grouped into three general categories of phytoavailability relative to TSP: high (> 75% of TSP), moderate (25-75% of TSP), and low (< 25% of TSP). Two biosolids, produced via biological phosphorus removal (BPR) processes, were in the high category, and mimicked fertilizer P with regard to P phytoavailability. Most biosolids produced by conventional wastewater and solids digestion and additional treatments like composting were in the moderate category. Also included in this category was a BPR that had been pelletized and another BPR supplemented with Al. The low category included biosolids containing greater than normal (> 50 g kg(-1)) total Fe and Al concentrations and processed to high (> 60%) solids content.     

Nutrient and trace element leaching following mine reclamation with biosolids

Mine reclamation with biosolids increases revegetation success but nutrient addition well in excess of vegetation requirements has the potential to increase leaching of NO3 and other biosolids constituents. A 3-yr water quality monitoring study was conducted on a Pennsylvania mine site reclaimed with biosolids applied at the maximum permitted and standard loading rate of 134 Mg ha(-1). Zero-tension lysimeters were installed at 1-m depth 1 yr before reclamation: three in the biosolids application area, one in a control area (no biosolids). Before reclamation, all water samples had pH in the range 4.7 to 6.2, acidity < 20 mg L(-1), and very low levels of all other measured parameters. Following reclamation, percolate water in the biosolids-treated area had lower pH and greater acidity than the control area. Acidity was greatest during the first winter following biosolids application, decreased during the spring, and showed a similar pattern but with much smaller concentrations the second year. Maximum first- year leachate NO3 concentrations were approximately 300 mg L(-1) and half as large the second year. Estimated inorganic N leaching loss during the first 2 yr after biosolids application was 2327 kg N ha(-1). Aluminum, Mn, Cu, Ni, Pb, and Zn followed similar leaching patterns as did acidity, and their mobilization appeared to be the result of the increased acidity. These results indicate that large applications of low-C/N-ratio biosolids could negatively impact area water quality and that biosolids reclamation practices should be modified to reduce this possibility.     

Use of adjuvants to minimize leaching of herbicides in soil

Excessive leaching of herbicides affects their efficacy against target weeds and results in contamination of groundwater. Use of adjuvants that can weakly bind herbicides and in turn release them slowly is a valuable technique to prolong the efficacy of herbicides and to minimize their leaching into groundwater. Effects of activated charcoal, three humic substances (Enersol SP 85%, Enersol 12%, and Agroliz), or a synthetic polymer (Hydrosorb) on the leaching of bromacil, dicamba, and simazine were investigated in leaching columns using a Candler fine sand (Typic Quartzipsamment). The addition of adjuvants had no harmful effects on physical properties of the soil as evident from lack of its affects on water percolation. When no adjuvants were used, 69%, 37%, and 4% of applied dicamba, bromacil, and simazine, respectively, were leached in the first pore volume of leachate (⋍3.2 cm rainfall). With five pore volumes of leachate (⋍16 cm rainfall), bromacil and dicamba were leached completely and only 80% of simazine was leached. Using Enersol 12% adjuvant resulted in a 13%–18% reduction in leaching of dicamba and bromacil in five pore volumes of leachate. The leaching of simazine was significantly decreased when any of the five adjuvants mentioned above were used. However, the decrease in leaching was significantly greater when using Enersol SP 85% or Enersol 12% (24%–28%) than when using the other adjuvants (12%–16%).     

Accelerated weathering of biosolid-amended copper mine tailings

Application of municipal biosolids to mine tailings can enhance revegetation success, but may cause adverse environmental impacts, such as increased leaching of NO3- and metals to ground water. Kinetic weathering cells were used to simulate geochemical weathering to determine the effects of biosolid amendment on (i) pH of leachate and tailings, (ii) leaching of NO3- and SO4(2-), (iii) leaching and bioavailability (DTPA-extractable) of selected metals, and (iv) changes in tailing mineralogy. Four Cu mine tailings from southern Arizona differing in initial pH (3.3-7.3) and degree of weathering were packed into triplicate weathering cells and were unamended and amended with two rates (equivalent to 134 and 200 Mg dry matter ha(-1)) of biosolids. Biosolid application to acid (pH 3.3) tailings resulted in pH values as high as 6.3 and leachate pH as high as 5.7, and biosolids applied to circumneutral tailings resulted in no change in tailing or leachate pH. Concentrations of NO3--N of up to 23 mg L(-1) occurred in leachates from circumneutral tailings. The low pH of the acidic tailing apparently inhibited nitrification, resulting in leachate NO3--N of <5 mg L(-1). Less SO4(2-)-S was leached in biosolid-amended versus unamended acid tailings (final rate of 0.04 compared with 0.11 g SO4(2-)-S wk(-1)). Copper concentrations in leachates from acidic tailings were reduced from 53 to 27 mg L(-1) with biosolid amendment. Copper and As concentrations increased slightly in leachates from biosolid-amended circumneutral tailings. Small increases in DTPA-extractable Cu, Ni, and Zn occurred in all tailings with increased biosolid rate. Overall, there was little evidence of potential for adverse environmental impacts resulting from biosolid application to these Cu mine tailings.     

Phosphorus restrictions for land application of biosolids: current status and future trends

The application of biosolids (sewage sludge) to agricultural soils provides P in excess of crop needs when applied to meet the N needs of most agronomic crops. These overapplications can result in the buildup of P in soils to values well above those needed for optimum crop yields and also may increase risk of P losses to surface and ground waters. Because of concerns regarding the influence of P on water quality in the USA, many state and federal agencies now recommend or require P-based nutrient management plans for animal manures. Similar actions are now under consideration for the land application of biosolids. We reviewed the literature on this subject and conducted a national survey to determine if states had restrictions on P levels in biosolids-amended soils. The literature review indicates that while the current N-based approach to biosolids management does result in increases of soil P, some properties of biosolids may mitigate the environmental risk to water quality associated with land application of P in biosolids. Results of the survey showed that 24 states have regulations or guidelines that can be imposed to restrict land application of biosolids based on P. Many of these states use numerical thresholds for P in biosolids-amended soils that are based on soil test phosphorus (STP) values that are much greater than the values considered to be agronomically beneficial. We suggest there is the need for a comprehensive environmental risk assessment of biosolids P. If risk assessment suggests the need for regulation of biosolids application, we suggest regulations be based on the P Site Index (PSI), which is the method being used by most states for animal manure management.     

Phosphorus in Hawaiian kikuyugrass pastures and potential phosphorus release to water

Pasture systems in Hawaii are based primarily on kikuyugrass (Pennisetum clandestinum Hochst. ex Chiov.). Relationships among kikuyugrass P concentration, animal P requirements, and various soil P determinations are needed to help identify source areas for implementing pasture management strategies to limit P loss via overland flow. A total of 51 rotationally stocked kikuyugrass pastures (>20 yr old) with contrasting soil chemical properties were sampled. A satisfactory predictive relationship between modified-Truog (MT)-extractable phosphorus (P(MT)) and dissolved (<0.45-mum pore diameter), molybdate-reactive phosphorus (DRP) desorbed from soil in a water extract (DRP(WE)) was found when 0- to 4-cm-depth data for the soil orders with medium to high DRP(WE) (two Mollisols and an Inceptisol) were pooled separately from those with low DRP(WE) (five Andisols, three Ultisols, and an Oxisol). The oxalate phosphorus saturation index (PSI(ox)) procedure was the best predictor of DRP(WE) across soil orders when oxalate-extractable molybdate-reactive phosphorus (RP(ox)) was used to calculate PSI(ox) (PSI(ox)RP) rather than when total oxalate-extractable phosphorus (TP(ox)) was used (PSI(ox)TP). There was little DRP(WE) until PSI(ox)RP exceeded 6% or PSI(ox)TP exceeded 8%. A more empirical dilute-acid phosphorus saturation index (PSI(MT)) was also calculated using P(MT) and MT-extractable iron (Fe(MT)) and aluminum (Al(MT)). The PSI(MT) procedure showed some utility in predicting DRP(WE), was positively related to the PSI(ox) procedures, and can be more readily performed in agronomic soil testing laboratories than PSI(ox). The present research suggests that while Hawaiian kikuyugrass pastures tend to be sufficient to high in forage P, potential soil P release to water only appeared to be a possible environmental concern for the Mollisol and Inceptisol sites.     

Phosphorus release from a manure-impacted spodosol: effects of a water treatment residual

Long-term depositions of animal manures affect P dynamics in soils and can pose environmental risks associated with P losses. Laboratory studies were done on P solubility characteristics in a manure-impacted Immokalee soil (sandy, siliceous, hyperthermic Arenic Alaquod) and the effectiveness of water treatment residual (WTR) in controlling P leaching. Soil samples with contrasting initial total P concentrations were prepared by mixing samples of a manure-impacted surface A horizon and a minimally P-impacted E horizon. Effects of mixing various ratios of A and E horizons, WTR rates (0, 25, 50, and 100 g kg(-1)), and depths of WTR incorporation (mixed throughout the soil column or partially incorporated) on P leaching were determined. Between 62 and 77% of total P was released from the soil mixes by successive water extractions, suggesting a considerable buffering capacity of this manure-impacted soil to resupply P into solution. Between 224 and 408 mg kg(-1) P were leached during the 36-wk leaching period in the absence of WTR. Mixing WTRs with soil reduced soluble P concentration in leachates by as much as 99.8% compared with samples without WTR. Thoroughly mixing WTR with the entire soil column (15 cm) was much more efficient than mixing WTR with only the top 7.5 cm of soil. Calcium- and Mg-P forms appear to control P release in soils without WTR, whereas sorption-desorption reactions probably determine P leaching in WTR-treated samples. Soil P distribution in various chemical forms was affected by WTR additions. Data suggest that WTR-immobilized P is stable in the long term.     

Effect of tomato packinghouse wastewater properties on phosphorus and cation leaching in a spodosol

Land application of wastewater is a common practice. However, coarse-textured soils and shallow groundwater in Florida present favorable conditions for leaching of wastewater-applied constituents. Our objective in this study was to determine phosphorus (P) and associated cations (Ca, Mg, K, Na) leaching in a Spodosol irrigated with tomato packinghouse wastewater. We packed 12 polyvinyl chloride soil columns (30 cm internal diameter × 50 cm length) with two soil horizons (Ap and A/E) and conducted 30 sequential leaching events by irrigating with wastewater at low (0.84 cm d), medium (1.68 cm d), and high (2.51 cm d) rates. The control treatment received deionized water at 1.68 cm d Leachate pH was lower (6.4-6.5) and electrical conductivity (EC) was higher in the wastewater-treated columns (0.85-1.78 dS m) than in the control treatment (pH 6.9; EC, 0.12 dS m) due to the low pH (6.2) and high EC (2.16 dS m) of applied wastewater. Mean leachate P concentrations were greatest in the control treatment (0.70 mg L), followed by the high (0.60 mg L) and low and medium wastewater-treated columns (0.28-0.33 mg L). Leachate concentrations of Na, Ca, Mg, and K were significantly ( < 0.05) greater in wastewater-treated columns than in the control. Concentrations of P, Na, and K in leachate remained lower than the concentrations in the applied wastewater, indicating their retention in the soil profile. In contrast, leachate Ca and Mg concentrations were greater than in applied wastewater during several leaching events, suggesting that additional Ca and Mg were leached from the soil. Our results suggest that tomato packinghouse wastewater can be beneficially land-applied at 1.68 cm d in Florida's Spodosols without significant P and cation leaching.     

Distribution of copper, zinc, and phosphorus in coastal plain soils receiving repeated liquid biosolids applications

Continuous N-based application of biosolids contributes to a gradual increase of trace elements and P in soils. The objectives of this study were to assess the accumulation and vertical transport of Cu, Zn, C, N, and P within the profile of two coastal plain soils. Liquid (6-8% total solids) biosolids were applied to an Acredale silt loam (fine silty, mixed, thermic typic Ochraqualfs) and Bojac loamy sand (coarse loamy, mixed, thermic typic Hapludult) annually from 1984 to 1998. The repeated applications supplied 70, 204, and 3823 kg ha(-1) of Cu, Zn, and P, respectively, to the Acredale and 81, 225, and 4265 kg ha(-1) of Cu, Zn, and P, respectively, to the Bojac. The total C and N contents were not different than background levels in the Bojac soil and were slightly higher in the Acredale soil 7 years after cessation of biosolids application. Phosphorus, Cu and Zn are still concentrated in the top 0.25 m of the Acredale soil. Enrichment of P, Cu, and Zn were detected to the deepest soil increment in the coarse-textured Bojac soil. Approximately 20 to 40% of the Cu and Zn applied in the biosolids could not be accounted, which was likely due to a combination of leaching and incomplete extraction. Excessive Mehlich 1-P concentrations and a high degree of P saturation were found in amended soil, raising the potential for P release to runoff or leaching water.     

Spectroscopic speciation and quantification of lead in phosphate-amended soils

The immobilization of Pb in contaminated soils as pyromorphite [Pb(5)(PO(4))(3)Cl, OH, F] through the addition of various phosphate amendments has gained much attention in the remediation community. However, it is difficult to fully determine the speciation and amount of soil Pb converted to pyromorphite by previously employed methods, such as selective sequential extraction procedures and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, which often lead to erroneous results in these non-equilibrated and heterogeneous systems. Statistical analysis by linear combination fitting (LCF) applied to X-ray absorption fine structure (XAFS) spectroscopic data of Pb-contaminated soil samples relative to known Pb reference material provides direct, in situ evidence of dominate Pb species in the amended soils without chemical or physical disruption to the Pb species as well as a weighted quantification output. The LCF-XAFS approach illustrated that pyromorphite concentration ranged from 0% (control soil) to 45% (1% phosphoric acid amendment, residence time of 32 mo) relative to the total Pb concentration. The Pb speciation in the nonamended control soil included Pb-sulfur species (galena + angelsite = 53%), adsorbed Pb (inner-sphere + outer-sphere + organic-bound = 45%), and Pb-carbonate phases (cerussite + hydrocerussite = 2%). The addition of P promoted pyromorphite formation and the rate of formation increased with increasing P concentration (up to 45%). The supplemental addition of an iron amendment as an iron-rich byproduct with triple superphosphate (TSP) enhanced pyromorphite formation relative to independent TSP amendment of like concentrations (41 versus 29%). However, the amendment of biosolids and biosolids plus TSP observed little pyromorphite formation (1-16% of total Pb), but a significant increase of sorbed Pb was determined by LCF-XAFS.     

Role of organic matter in microbial transport during irrigation with sewage effluent

Reduction of migration of fecal coliforms (FC) and streptococci (FS) by limiting the leaching in effluent-irrigated soil was tested in lysimeters packed with quartz sand without or with added biosolids compost or with one of two clayey soils. The 200-L, 70-cm-deep lysimeters were either planted with a Eucalyptus camaldulensis or an Oroblanco citrus tree (in the sand only), or not planted. The Eucalyptus was irrigated with oxidation pond effluent (OPE) and the Oroblanco with mechanical-biological treatment plant effluent (MBTPE). The leaching fraction (LF) ranged from 0.2 to about 1.0, and the residence time (RT) from under 1 to 40 d. The Eucalyptus was also tested under intermittent leaching (RT 11-20 d) and deficit irrigation (without leaching for about 6 mo) regimes. Under MBTPE irrigation there was little or no leaching of FC and FS. Under OPE irrigation at LF 1 without a Eucalyptus there was little or no bacterial leaching at irrigation rates below 40 L d(-1) per lysimeter (RT > or = 0.8 d). Bacterial counts in the leachate were substantial in the presence of a Eucalyptus tree under LF 0.2 and intermittent leaching regimes, and when sand-packed unplanted lysimeters received OPE effluent at >45 L d(-1). Bacterial recovery peaked at LF 0.2, at up to 45% of the input level. At LF 1 (RT 0.6-2.8 d) and with intermittent leaching the recoveries were minute. Bacterial counts in the washout from the deficit-irrigated lysimeters were typical of nonpolluted soils. The bacterial concentration and recovery patterns in the leachate mostly matched the organic carbon (OC) load in the irrigation water, and its concentration and bioavailablity in the leachate. We related the leaching patterns of the fecal bacteria to their relative reproduction and die-off rates, and to the dependence of their regrowth on available carbon sources.     

Runoff phosphorus losses from surface-applied biosolids

Runoff losses of dissolved and particulate phosphorus (P) may occur when rainfall interacts with manures and biosolids spread on the soil surface. This study compared P levels in runoff losses from soils amended with several P sources, including 10 different biosolids and dairy manure (untreated and treated with Fe or Al salts). Simulated rainfall (71 mm h(-1)) was applied until 30 min of runoff was collected from soil boxes (100 x 20 x 5 cm) to which the P sources were surfaced applied. Materials were applied to achieve a common plant available nitrogen (PAN) rate of 134 kg PAN ha(-1), resulting in total P loading rates from 122 (dairy manure) to 555 (Syracuse N-Viro biosolids) kg P ha(-1). Two biosolids produced via biological phosphorus removal (BPR) wastewater treatment resulted in the highest total dissolved phosphorus (13-21.5 mg TDP L(-1)) and total phosphorus (18-27.5 mg TP L(-1)) concentrations in runoff, followed by untreated dairy manure that had statistically (p = 0.05) higher TDP (8.5 mg L(-1)) and TP (10.9 mg L(-1)) than seven of the eight other biosolids. The TDP and TP in runoff from six biosolids did not differ significantly from unamended control (0.03 mg TDP L(-1); 0.95 mg TP L(-1)). Highest runoff TDP was associated with P sources low in Al and Fe. Amending dairy manure with Al and Fe salts at 1:1 metal-to-P molar ratio reduced runoff TP to control levels. Runoff TDP and TP were not positively correlated to TP application rate unless modified by a weighting factor reflecting the relative solubility of the P source. This suggests site assessment indices should account for the differential solubility of the applied P source to accurately predict the risk of P loss from the wide variety of biosolids materials routinely land applied.     

A spatially explicit investigation of phosphorus sorption and related soil properties in two riparian wetlands

Soils of riparian wetlands are highly effective at phosphorus (P) sorption. However, these soils exhibit extreme spatial variability across riparian zones. We used a spatially explicit sampling design in two riparian wetlands in North Carolina to better understand the relationships among P sorption, soil properties, and spatial variability. Our objectives were to quantify patterns of spatial variability of P sorption and related soil properties, and to determine which soil properties best explained the variability in P sorption after accounting for the effects of spatial autocorrelation. We measured bulk density, moisture, pH, soil organic matter (SOM), texture (percent clay, silt, and sand), oxalate-extractable aluminum (Al(ox)), iron (Fe(ox)), and the phosphorus sorption index (PSI). Due to differences in texture, Al(ox), and Fe(ox), the two sites had substantially different mean PSIs. At each site, we found considerable differences in the spatial variability of soil properties. For example, semivariance analysis and kriging illustrated that soil properties at Site 1 varied at smaller scales than those at Site 2. At both sites, after accounting for the effects of spatial autocorrelation and all other soil properties, we determined that Al(ox) had the highest Mantel correlation with PSI. We believe this geostatistic and Mantel approach is robust and could serve as a model for research on other biogeochemical processes such as denitrification.     

A method for determining the phosphorus sorption capacity and amorphous aluminum of aluminum-based drinking water treatment residuals

A high amorphous aluminum or iron oxide content in drinking water treatment residuals (WTRs) can result in a high phosphorus (P) sorption capacity. Therefore, WTR may be used beneficially to adsorb P and reduce P loss to surface or ground water. The strong relationship between acid ammonium oxalate-extractable aluminum (Al(ox)) and Langmuir phosphorus adsorption maximum (P(max)) in WTR could provide a useful tool for determining P(max) without the onus of the multipoint batch equilibrations necessary for the Langmuir model. The objectives of this study were to evaluate and/or modify an acid ammonium oxalate extraction of Al(ox) and the experimental conditions used to generate P adsorption isotherms to strengthen the relationship between Al(ox) and P(max). The oxalate extraction solution to WTR ratio varied from 40:1, 100:1, and 200:1. Batch equilibration conditions were also varied. The WTR particle size was reduced from <2 mm to <150 microm, and batch equilibration was extended from 17 h to 6 d. Increasing the solution to WTR ratio to 100:1 extracted significantly greater Al(ox) at levels of >50 mg Al kg(-1). No additional increase was found at 200:1. Reducing WTR particle size from <2 mm to <150 microm increased P(max) 2.46-fold. Extending the equilibration time from 17 h to 6 d increased P(max) by a mean of 5.83-fold. The resulting empirical regression equation between the optimized Al(ox) and P(max) (r(2) = 0.91, significant at the 0.001 probability level) may provide a tool to estimate the P(max) of Al-based WTR simply by measuring Al(ox). The accurate determination of WTR P(max) and Al(ox) is essential in using WTR effectively to reduce P loss in runoff or to reduce the solubility of P in agricultural soils or organic waste materials (biosolids, manure).