Thermal energy storage and thermodynamic properties of (E)-3-m-tolylbut-2-enoic acid as a medium temperature phase change material

Phase change materials (PCMs) that can store and release heat energy over the temperature range from 363 to 393 K are crucial for solar absorption cooling, and it is worthy to seek new solid-liquid PCMs candidates that melt and crystallize in this temperature range. In this paper, (E)-3-m-tolylbut-2-enoic acid (mTBEA) was applied as a PCM candidate. Its thermal energy storage properties and thermal stability were systematically investigated. The results showed that mTBEA melted at 382.9 ± 0.5 K and crystallized at about 364 K, with a melting enthalpy (Δ_fusH) of 138.4 ± 6.9 J g^?1 and showed good long-term cyclic stability and thermal stability. The supercooling of mTBEA was stabilized at about 20 K, indicating that the conservation condition of melted mTBEA could be simple. In addition, the melted mTBEA could release all the absorbed thermal energy upon crystallizing. Besides, mTBEA exhibited good thermal stability for it to be applied as PCM. Hence, mTBEA is a promising PCM candidate for solar absorption cooling. Furthermore, the heat capacity of mTBEA was measured by modulated temperature differential scanning calorimetry (MTDSC) over the temperature range from 198.15 to 431.15 K, and the molar thermodynamic functions, [H_T-H_298.15]_m and [S_T-S_298.15]_m, were calculated based on the fitted molar heat capacity data.     

PCM thermal conductivity effect on mechanism of PV/PCM thermal control characteristics

ABSTRACT

According to the structure of photovoltaic/phase change material (PV/PCM), the mechanism of internal heat transfer, transmission, storage, and temperature control is analyzed, and a two-dimensional finite element analysis model of PV/PCM structure is established. This study is carried out on the effect of PCM thermal conductivity on internal temperature distribution characteristics of PV/PCM and temperature control characteristics of solar cells. The results show that the increase in thermal conductivity of PCM can prolong the temperature control time of solar cell in PV/PCM system, for example, when the thermal conductivity is increased from 0.2 W/(m·K) to1.5 W/(m·K) under a thickness of 4 cm, the duration when PV/PCM solar cell temperature is controlled below 40°C and extended from 52 min to 184 min. In addition, PV/PCM experimental prototypes are designed with the LA-SA-EG composite PCM peak melting point of 46°C and thermal conductivity of 0.8 W/(m·K) and 1.1 W/(m·K), respectively. The results indicate that compared with PCM-free solar cells, the maximum temperature of PV/PCM prototype solar cells with thermal conductivity of 0.8 W/(m·K) and 1.1 W/(m·K) is reduced by 10.8°C and 4.6°C, respectively, with average output power increased by 4.1% and 2.2%, respectively, under simulated light sources. Under natural light conditions, the average output power is increased by 6.9% and 4.3%, respectively. The results provide theoretical and experimental basis for the optimization of PV/PCM design by changing the thermal conductivity of PCM.     

Investigation of activated carbon/ethanol for low temperature adsorption cooling

Commercially available adsorption cooling systems use water/silica gel, water/zeolite and ammonia/ chloride salts working pairs. The water-based pairs are limited to work above 0°C due to the water high freezing temperature, while ammonia has the disadvantage of being toxic. Ethanol is a promising refrigerant due to its low freezing point (161 K), nontoxicity, zero ozone depletion, and low global warming potential. Activated carbon (AC) is a porous material with high degree of porosity (500–3000 m²/g) that has been used in wide range of applications. Using Dynamic Vapour Sorption (DVS) test facility, this work characterizes the ethanol adsorption of eleven commercially available activated carbon materials for cooling at low temperature of ?15°C. DVS adsorption results show that Maxsorb has the best performance in terms of ethanol uptake and adsorption kinetics compared to the other tested materials. The Maxsorb/ethanol adsorption process has been numerically modeled using computational fluid dynamics (CFD) and simulation results are validated using the DVS experimental measurements. The validated CFD simulation of the adsorption process is used to predict the effects of adsorbent layer thickness and packing density on cycle uptake for evaporating temperature of ?15°C. Simulation results show that as the thickness of the Maxsorb adsorbent layer increases, its uptake decreases. As for the packing density, the amount of ethanol adsorbed per plate increases with the packing density reaching maximum at 750 kg/m³. This work shows the potential of using Maxsorb/ethanol in producing low temperature cooling down to ?15°C with specific cooling energy reaching 400 kJ/kg.     

Net Carbon Sequestration Potential and Emissions in Home Lawn Turfgrasses of the United States

Soil analyses were conducted on home lawns across diverse ecoregions of the U.S. to determine the soil organic carbon (SOC) sink capacity of turfgrass soils. Establishment of lawns sequestered SOC over time. Due to variations in ecoregions, sequestration rates varied among sites from 0.9 Mg carbon (C) ha^?1 year^?1 to 5.4 Mg C ha^?1 year^?1. Potential SOC sink capacity also varied among sites ranging from 20.8 ± 1.0–96.3 ± 6.0 Mg C ha^?1. Average sequestration rate and sink capacity for all sites sampled were 2.8 ± 0.3 Mg C ha^?1 year^?1 and 45.8 ± 3.5 Mg C ha^?1, respectively. Additionally, the hidden carbon costs (HCC) due to lawn mowing (189.7 kg Ce (carbon equivalent) ha^?1 year^?1) and fertilizer use (63.6 kg Ce ha^?1 year^?1) for all sites totaled 254.3 kg Ce ha^?1 year^?1. Considering home lawn SOC sink capacity and HCC, mean home lawn sequestration was completely negated 184 years post establishment. The potential SOC sink capacity of home lawns in the U.S. was estimated at 496.3 Tg C, with HCC of between 2,504.1 Gg Ce year^?1 under low management regimes and 7551.4 Gg Ce year^?1 under high management. This leads to a carbon-positive system for between 66 and 199 years in U.S. home lawns. More efficient and reduction of C-intensive maintenance practices could increase the overall sequestration longevity of home lawns and improve their climate change mitigation potential.     

Experimental investigation on effect of an absorber plate covered by a layer of sand on the efficiency of passive solar air collector

A passive flat-plate solar air collector was constructed in the laboratory of New and Renewable Energy in Arid Zones, Ouargla University, South East Algeria. The absorber of the passive flat-plate solar air collector was laminated with a thin layer of local sand. This acted as a thermal packed bed with a collecting area of 0.5 m² (1 m × 0.5 m). Three series of experiments were performed. The first consisted of choosing the best sand brought from three different places of the Algerian desert. The second consisted of studying the effect of the thickness of the sand layer on the daily efficacy of the collector. The influence of the sand diameter was investigated in the third series. The experimental results showed that: All collectors covered with sand had higher efficiency than those without. It was noticed that, for a fixed mass of sand (given thickness of the sand layer), the improvement of the collector was inversely proportional to the sand particle diameters. The maximum efficiency approximates 62.1% for a particle diameter 0.063 mm, compared to 41.71% for a diameter 0.250 mm.The efficiency of the collector for a fixed particle diameter increases with the increase in the thickness of the sand layer. The collector with thickness sand layer 0.84 mm gave the best efficiency of 46.14% compared to 27.8% for 0.28 mm of thickness sand layer.     

Novel mesoporous microspheres of Al and Ni doped LMO spinels and their performance as cathodes in secondary lithium ion batteries

A facile, scalable, and solution-based technique is used to fabricate Al and Ni-doped (LiAl_0.1Mn_1.9O₄ and LiAl_0.1Ni_0.1Mn_1.8O₄) microspheres of lithium manganese oxide (LMO) spinels for use as reversible cathode materials for lithium ion batteries (LIBs). The spheres of the two samples exhibit different porosities. Cells with these LMO-based cathodes are then cycled between 4.5 V and 2 V to study their stabilities while simultaneously being subjected to the undesirable Jahn-Teller distortion that occurs around the ~3 V regime. The LiAl_0.1Mn_1.9O₄ (LAMO) and the LiAl_0.1Ni_0.1Mn_1.8O₄ (LANMO) cells exhibit comparable open circuit voltages (OCV) of 2.94 V and 2.97 V, respectively. During cell cycling, the LAMO cell exhibits a maximum specific capacity of 122.51 mAh g^?1 with a capacity fade of 65.35% after 75 cycles. The LiAl_0.1Ni_0.1Mn_1.8O₄ (LAMO) sample fares better and exhibits a maximum of 140.49 mAh g^?1 and a capacity drop of 52.59%. Detailed structural studies indicate that Ni doping and the greater degree of porosity of the LANMO sample to be a stabilizing factor. This is further confirmed by cyclic voltammetry (CV) and AC impedance spectra analysis.     

Numerical studies on the thermal regimes of the horizontal tube falling film evaporation under varying feeder height

ABSTRACT

This paper discusses about the effect of feeder height and heat flux on the heat transfer characteristics of horizontal tube falling film evaporation in the thermal regimes. In order to investigate this, a two- dimensional CFD model was developed to perform simulation and results were compared and validated with published data available in the literature. Heat transfer co-efficients in the thermal regimes were determined from the CFD simulation and the results were recorded, analyzed and validated with the mathematical models available in the literature. The novelty of the current study is to predict the commencement of the fully developed thermal region over the tube from the simulation model under varying feeder height and heat flux. An effort was also made to measure the liquid film thickness around the tube from the CFD model in the thermal regimes. It is observed that angle of thermally developing region contracts and fully developed thermal region extends with the increase of the feeder height and heat flux. It is observed from the study that increase of heat flux by 10 kW/m² resulted in increase of heat transfer co-efficient value by 10–12% average in thermally developing region and 12–15% average in fully developed region. Thinnest liquid film thickness observed between 85 and 127°angle. Shifting of thinnest region of liquid film upward from the mid tube with the increase of the feeder height and heat flux is noted.     

Fatty Acids as Phase Change Materials (PCMs) for Thermal Energy Storage: A Review

Abstract

Thermal energy storage (TES) technologies in general and phase change materials (PCMs) in particular, have been topic in research for the last 20 years. Traditionally, available heat has been stored in the form of sensible heat (typically by raising temperature of water, rocks, etc). Latent heat storage on the other hand, is a novel and developing technology, which has found considerable interest due to its operational advantages of smaller temperature swing, smaller size, and lower weight per unit of storage capacity. The interest on thermal energy storage by using fatty acids as PCM has risen in recent times since they have desired thermodynamic and kinetic criteria for low temperature latent heat storage. An added advantage is that fatty acids are derived from the vegetable and animals oil that provides an assurance of continuous supply. This article will review the development of fatty acids as PCMs for solar thermal energy storage application.     

Effect of Fenton pretreatment on anaerobic digestion of olive mill wastewater and olive mill solid waste in mesophilic conditions

The olive mill waste (OMW) generated from olive oil extraction process constitutes a major environmental concern owing to its high organic and mineral matters and acidic pH. Anaerobic digestion (AD) is a main treatment for reducing the organic matter and toxic substances contained in OMW and generating at the same time, energy in the form of biogas. AD of OMW that contains lignocellulose is limited by the rate of hydrolysis due to their recalcitrant structure. This study is devoted to the effect of Fenton process (FP) pretreatment on olive mill wastewater (OMSW) /olive mill solid waste (OMWW) co-digestion to improve their digestibility and in this way the biogas production. The FP pretreatment was performed in batch mode at 25°C, various H₂O₂/[Fe²⁺] ratios (100–1200), catalyst concentration ([Fe²⁺]) ranging from 0.25 to 2 mM, reaction time varying from 30 to150 min, and different pH (3–11). The best performance was obtained with H₂O₂/[Fe²⁺] = 1000, [Fe²⁺] = 1.5 mM, 120 min, and pH 3. Biochemical methane potential (BMP) tests conducted in batch wise digester and at mesophilic conditions (37 °C) showed that cumulative biogas and methane production were higher without FP treatment, and correspond to 699 and 416 mL/g VS, respectively. However, pre-treated OMSW results into an increase of 24% of methane yield. After 30 days of AD, the methane yield was 63%, 54%, and 48%, respectively, for OMSW treated without iron precipitation, with iron precipitation and untreated OMSW sample.     

Experimental thermal storage research of organic binary phase change materials in building environment

This paper aims to reveal the heat transfer mechanism of low-temperature phase change material (PCM) and design PCM heat storage device in building heating environment. Firstly, low-temperature binary PCMs of lauric acid and stearic acid are prepared, and their thermal properties are investigated by DSC. Then, shell and tube latent heat thermal energy storage units are conducted, and heat transfer experiments are carried out to analyze the heat transfer mechanism of PCM. The results demonstrate that natural convection plays an important role in heat transfer process, and the heat storage efficiency of PCMs can be significantly enhanced by increasing the fin width and improving the inlet heat transfer fluid (HTF) temperature. Furthermore, some proposals are put forward to guide the design of PCM storage device in building heating environment.     

Dam Design can Impede Adaptive Management of Environmental Flows: A Case Study from the Opuha Dam, New Zealand

The Opuha Dam was designed for water storage, hydropower, and to augment summer low flows. Following its commissioning in 1999, algal blooms (dominated first by Phormidium and later Didymosphenia geminata) downstream of the dam were attributed to the reduced frequency and magnitude of high-flow events. In this study, we used a 20-year monitoring dataset to quantify changes associated with the dam. We also studied the effectiveness of flushing flows to remove periphyton from the river bed. Following the completion of the dam, daily maximum flows downstream have exceeded 100 m³ s^?1 only three times; two of these floods exceeded the pre-dam mean annual flood of 203 m³ s^?1 (compared to 19 times >100 m³ s^?1 and 6 times >203 m³ s^?1 in the 8 years of record before the dam). Other changes downstream included increases in water temperature, bed armoring, frequency of algal blooms, and changes to the aquatic invertebrate community. Seven experimental flushing flows resulted in limited periphyton reductions. Flood wave attenuation, bed armoring, and a shortage of surface sand and gravel, likely limited the effectiveness of these moderate floods. Floods similar to pre-dam levels may be effective for control of periphyton downstream; however, flushing flows of that magnitude are not possible with the existing dam infrastructure. These results highlight the need for dams to be planned and built with the capacity to provide the natural range of flows for adaptive management, particularly high flows.     

The convective hot air drying of Lactuca sativa slices

The storage of fresh agricultural products is not easy because of its high moisture. Dehydration is an efficient preservation method. The investigation of drying modeling and transfer characteristics are important for selecting operating conditions and equipment design. The drying behavior of Lactuca sativa slices, with the thickness of 2 mm, was investigated at 60.0–80.0°C and 0.60–1.04 m sec^?1 velocity in a convective hot air drier. The mass transfer during the drying process was described using six thin drying models. The convective heat transfer coefficient α and mass transfer coefficient k_H were finally calculated. The results showed that the drying process could be separated into three stages including accelerating rate, constant rate, and falling rate period, which was influenced by hot air temperature and velocity, and the Modi?ed Page model agreed well with the experimental data. When the operating temperature was increased from 60.0°C to 80.0°C, α was found increased from 88.07 to 107.93 W·m^?2·K^?1, and k_H increased from 46.32 × 10^–3 to 68.04 × 10^–3 kg·m^?2·sec^?1·ΔH^?1. With the increase of air velocity from 0.60 to 1.04 m·sec^?1, α was increased from 78.85 to 101.35 W·m^?2·K^?1, and k_H was enhanced from 51.78 × 10^–3 to 65.85 × 10^–3 kg·m^?2·sec^?1·ΔH^?1.     

Generation Performance of Gas-Feed Direct Methanol Fuel Cell

Abstract

The modification effect of Nafion on the generation performance at different temperatures and methanol concentrations was investigated. The direct methanol fuel cell performances and electrochemical properties of the DMFC system using as-received Nafion117, a modified Nafion membrane, and using the Nafion117 MEA preparation by spray treatment on the surface of each catalyst layer for conductivity improvement. The open circuit voltage using the modified Nafion membrane was higher than that using Nafion117 at the cell temperature of 343–383 K and methanol concentration of 1.5–10 kmol/m³. The spray treatment of MEA was effective and improved the short circuit current up to 461 mA/cm² at a 5 kmol/m³ methanol concentration in comparison with no treatment of MEA because of the low interfacial resistance. The power density of 75 mW/cm² (no treatment Nafion117 MEA:40 mW/cm²) was obtained. The method of the spray treatment was found to be very effective for the DMFC system. The cell performance of Nafion117 MEA increased with the methanol concentration because of the reduction of the concentration overvoltage.     

Optimizing Li2O-2B2O3 coating layer on LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode material for high-performance lithium-ion batteries

ABSTRACT

In this paper, a wet chemical method is used to coat LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811) cathode material by Li₂O-2B₂O₃ (LBO) layer for Lithium-ion batteries (LIBs). For performance optimization, the effects of different contents (thicknesses) of LBO coating layers on NCM811 particle surface on the morphologies, structures, compositions, and electrochemical properties of the corresponding LIBs are studied using XRD, SEM, TEM, and electrochemical measurements. Coin LIBs are assembled with such coated NCM811 cathode materials for performance validation. Results show that LBO coating layer does not change the original lattice structure of the bulk material, it can only adhere to the surface of the bulk material. After coating, NCM811 shows a good crystallinity and the ordered layered structure. TEM images show that the thickness of LBO coating is increased with increasing LBO content, and that the appropriate LBO coating thickness and uniform coating state are conducive to the improvement of the electrochemical properties of NCM811 cathode materials. Particularly, NCM811 with LBO coating content of 1000 ppm shows the best performance compared to other coating contents. In this case, the coating thickness is relatively uniform, which is about 40～100 nm, giving a good first charge-discharge capacity of 214.1mAh/g, and a high Coulomb efficiency of 90.06%. After 50 cycles, the capacity retention rate of LIBs still keeps as high as 99.64%. Therefore, LBO coating can improve the performance of NCM811 and then the lithium-ion batteries.     

The global solar radiation estimation and analysis of solar energy: Case study for Osmaniye,Turkey

This paper investigates the prediction of solar radiation model and actual solar energy in Osmaniye, Turkey. Four models were used to estimate using the parameters of sunshine duration and average temperature. In order to obtain the statistical performance analysis of models, the coefficient of determination (R²), mean absolute percentage error (MAPE), mean absolute bias error (MABE), and root mean square error (RMSE) were used. Results obtained from the linear regression using the parameters of sunshine duration and average temperature showed a good prediction of the monthly average daily global solar radiation on a horizontal surface. In order to obtain solar energy, daily and monthly average solar radiation values were calculated from the five minute average recorded values by using meteorological measuring device. As a result of this measurement, the highest monthly and yearly mean solar radiation values were 698 (April in 2013) and 549 (2014 year) W/m² respectively. On an annual scale the maximum global solar radiation changes from 26.38 MJ/m²/day by June to 19.19 MJ/m²/day by September in 2013. Minimum global solar radiation changes from 14.05 MJ/m²/day by October to 7.20 MJ/m²/day by January in 2013. Yearly average energy potential during the measurement period was 16.53 MJ/m²/day (in 2013). The results show that Osmaniye has a considerable solar energy potential to produce electricity.     

Soil Organic Carbon Stock and Distribution in Cultivated Land Converted to Grassland in a Subtropical Region of China

Land-use change from one type to another affects soil carbon (C) stocks which is associated with fluxes of CO₂ to the atmosphere. The 10-years converted land selected from previously cultivated land in hilly areas of Sichuan, China was studied to understand the effects of land-use conversion on soil organic casrbon (SOC) sequestration under landscape position influences in a subtropical region of China. The SOC concentrations of the surface soil were greater (P < 0.001) for converted soils than those for cultivated soils but lower (P < 0.001) than those for original uncultivated soils. The SOC inventories (1.90–1.95 kg m^?2) in the 0–15 cm surface soils were similar among upper, middle, and lower slope positions on the converted land, while the SOC inventories (1.41–1.65 kg m^?2) in this soil layer tended to increase from upper to lower slope positions on the cultivated slope. On the whole, SOC inventories in this soil layer significantly increased following the conversion from cultivated land to grassland (P < 0.001). In the upper slope positions, converted soils (especially in 0–5 cm surface soil) exhibited a higher C/N ratio than cultivated soils (P = 0.012), implying that strong SOC sequestration characteristics exist in upper slope areas where severe soil erosion occurred before land conversion. It is suggested that landscape position impacts on the SOC spatial distribution become insignificant after the conversion of cultivated land to grassland, which is conducive to the immobilization of organic C. We speculate that the conversion of cultivated land to grassland would markedly increase SOC stocks in soil and would especially improve the potential for SOC sequestration in the surface soil over a moderate period of time (10 years).     

Certified and Uncertified Logging Concessions Compared in Gabon: Changes in Stand Structure, Tree Species, and Biomass

Forest management certification is assumed to promote sustainable forest management, but there is little field-based evidence to support this claim. To help fill this gap, we compared a Forest Stewardship Council (FSC)-certified with an adjacent uncertified, conventionally logged concession (CL) in Gabon on the basis of logging damage, above-ground biomass (AGB), and tree species diversity and composition. Before logging, we marked, mapped, and measured all trees >10 cm dbh in 20 and twelve 1-ha permanent plots in the FSC and CL areas, respectively. Soil and tree damage due to felling, skidding, and road-related activities was then assessed 2–3 months after the 508 ha FSC study area and the 200 ha CL study area were selectively logged at respective intensities of 5.7 m³/ha (0.39 trees/ha) and 11.4 m³/ha (0.76 trees/ha). For each tree felled, averages of 9.1 and 20.9 other trees were damaged in the FSC and CL plots, respectively; when expressed as the impacts per timber volume extracted, the values did not differ between the two treatments. Skid trails covered 2.9 % more of the CL surface, but skid trail length per unit timber volume extracted was not greater. Logging roads were wider in the CL than FSC site and disturbed 4.7 % more of the surface. Overall, logging caused declines in AGB of 7.1 and 13.4 % at the FSC and CL sites, respectively. Changes in tree species composition were small but greater for the CL site. Based on these findings and in light of the pseudoreplicated study design with less-than perfect counterfactual, we cautiously conclude that certification yields environmental benefits even after accounting for differences in logging intensities.     

Thermally chargeable supercapacitor based on nickel-coated nanoporous carbon

Nanoporous carbon is coated by pure nickel via an electroless plating method. The nanoporous carbon provides a high-surface-area substrate, leading to a large capacitance; the nickel surface layer is of a high work function, resulting in a thermally sensitive electrode potential. Such a system is ideal for thermally chargeable supercapacitor (TCS) system, which converts low-grade heat (LGH) to electrical energy. The specific energy per thermal cycle per gram of electrode mass is ~1.8 mJ, with a temperature difference of 50°C.     

Regional and Local Scale Modeling of Stream Temperatures and Spatio-Temporal Variation in Thermal Sensitivities

Understanding variation in stream thermal regimes becomes increasingly important as the climate changes and aquatic biota approach their thermal limits. We used data from paired air and water temperature loggers to develop region-scale and stream-specific models of average daily water temperature and to explore thermal sensitivities, the slopes of air–water temperature regressions, of mostly forested streams across Maryland, USA. The region-scale stream temperature model explained nearly 90 % of the variation (root mean square error = 0.957 °C), with the mostly flat coastal plain streams having significantly higher thermal sensitivities than the steeper highlands streams with piedmont streams intermediate. Model R ² for stream-specific models was positively related to a stream’s thermal sensitivity. Both the regional and the stream-specific air–water temperature regression models benefited from including mean daily discharge from regional gaging stations, but the degree of improvement declined as a stream’s thermal sensitivity increased. Although catchment size had no relationship to thermal sensitivity, steeper streams or those with greater amounts of forest in their upstream watershed were less thermally sensitive. The subset of streams with three or more summers of temperature data exhibited a wide range of annual variation in thermal sensitivity at a site, with the variation not attributable to discharge, precipitation patterns, or physical attributes of streams or their watersheds. Our findings are a useful starting point to better understand patterns in stream thermal regimes. However, a more spatially and temporally comprehensive monitoring network should increase understanding of stream temperature variation and its controls as climatic patterns change.     

Pyrolysis of commingled waste textile fibers in a batch reactor: Analysis of the pyrolysis gases and solid product

The main object of this study was the investigation of the thermal recycling of commingled waste textile fibers, with the aim of the production of useful end products. Differential scanning calorimetry/Thermo gravimetric analysis (DSC/TGA) was applied to determine the thermal degradation characteristics of the commingled waste textile fibers and there are two peaks located at the temperature ranges of 299–360°C and 399–500°C. Commingled waste fiber was pyrolyzed in a nitrogen atmosphere in relation to three different temperatures (500, 600, and 700°C), heating rates (25 and 50°C min^?1), and retention times (15 and 30 min). The effect of the experimental conditions such as pyrolysis temperature, heating rates, and retention time on the formation of char and gas--liquid products was investigated and the product yields were determined from the rate of the weight loss. The highest conversion rate 82.9 wt.% liquid--gas product and 17.1 wt.% char product was achieved at 700°C. Pyrolysis gases were taken for every 7, 15, and 25 min and were analyzed for major components such as CO, CO₂, CH₄, and H₂ by gas chromatography. The pyrolysis char called as carbon black derived from the pyrolysis of commingled waste textile fibers was analyzed for a range of properties, including the elemental analysis, moisture content, ash content, calorific value, and trace metal analysis.