基于TMVOC的地下水位波动带苯系物迁移转化模拟

为探究水位波动情况下苯系物的迁移转化规律,提高石油污染场地地下水污染治理精度,以西北某傍河石化场地为研究对象,基于TMVOC模型对特征污染物苯系物开展泄漏模拟,通过情景模拟比较水位波动对苯系物迁移转化的影响,并从污染分布、相间转化等方面,解析地下水位稳定和波动状态下苯系物迁移转化过程差异.结果表明:①TMVOC模型较好地模拟了水位波动状态下苯系物迁移转化过程.②相较于水位稳定状态下,水位波动作用下苯系物污染深度增加0.5 m,污染面积增加25%,总质量增加12 kg.③水位稳定和波动状态下苯系物"气-液-NAPL（Non-Aqueous Phase Liquids）相"占比分别为0.17%、2.03%、97.8%和0.04%、3.69%、96.27%.④NAPL相苯系物饱和度分布与苯系物质量分布呈正相关,水位波动造成NAPL相初始饱和度降低,且初始水位面以下NAPL相饱和度升高.⑤对于苯而言,水位波动状态下非饱和带中苯在液相中的质量是水位稳定状态下的1.11倍,饱和带为10.15倍.研究显示,水位波动显著地影响了苯系物的迁移转化过程,促进了苯系物的溶解,并使更多的苯系物残留在地下介质中.      

Evidence for biodegradation and volatilisation of dissolved petroleum hydrocarbons during in situ air sparging in large laboratory columns

Laboratory column experiments run for up to 13 days compared air sparging of groundwater contaminated by dissolved petroleum hydrocarbons in sterile and non-sterile aquifer sediments as well as uncontaminated sediments and groundwater. Loss of dissolved BTEX compounds in the contaminated columns was very rapid, occurring through volatilisation. The majority of the dissolved total organic carbon (TOC) persisted for much longer periods however. A direct comparison between losses from sterile and non-sterile columns suggested a negligible contribution of biodegradation to the removal of TOC. This was difficult to confirm through examination of O₂ utilisation because oxidation of a small amount of reduced sulphur in the aquifer materials was the dominant sink for O₂. Despite this, it was possible to conclude that less than 22% of the removal of TOC was through biodegradation during the first three days of air sparging.     

BTEX pollution caused by motorcycles in the megacity of HoChiMinh

Monitoring of benzene, toluene and xylenes (BTEX) was conducted along with traffic counts at 17 roadside sites in urban areas of HoChiMinh. Toluene was the most abundant substance, followed by p,m-xylenes, benzene, o-xylene and ethylbenzene. The maximum observed hour-average benzene concentration was 254 μg/m3 . Motorcycles contributed to 91% of the traffic fleet. High correlations among BTEX species, between BTEX concentrations and the volume of on-road motorcycles, and between inter-species ratios in air and in gasoline indicate the motorcycle-exhaust origin of BTEX species. Daily concentrations of benzene, toluene, ethylbenzene, p,m-xylenes and o-xylene were 56, 121, 21, 64 and 23 μg/m 3 , respectively. p,m-xylenes possess the highest ozone formation potential among the BTEX family.     

生物活性炭去除水中挥发性苯系物的基础研究

采用连续流生物活性炭(BAC)工艺处理水中挥发性苯系物(BTEX,包括苯、甲苯、乙苯、二甲苯),评价进水负荷、活性炭炭型等因素对于BAC处理性能的影响.研究表明,在40d的处理时间内,除苯之外,其余BTEX的BAC出水中均未检出苯系物(进水为6mg/L).为了检验BAC在高BTEX负荷情况时的处理效果,将进水浓度设定为19~32mg/L左右,在EBCT为1.2min条件下同样只有苯的出水浓度上升至10mg/L(C/Cin为0.45),然后略有下降,最终保持在5~10mg/L(C/Cin为0.3以下),其余苯系物出水浓度均一直保持小于5mg/L.这表明BAC可以有效地处理高负荷BTEX(8.68~12.9kgTOC/(m3·d))的进水.生物活性炭对于活性炭吸附容量的恢复有比较明显的作用,煤质炭和椰壳炭的生物再生效率分别为53.6%和26.6%,煤质炭再生效率高的原因可能是其具备更多的大型中孔和大孔.     

Groundwater contamination and natural attenuation capacity at a petroleum spilled facility in Korea

As a remedial option, the natural attenuation capacity of a petroleum contaminated groundwater at a military facility was examined. Hydrogeological conditions, such as high water level, permeable uppermost layer and frequent heavy rainfall, were favorable to natural attenuation at this site. The changes in the concentrations of electron acceptors and donors, as well as the relevant hydrochemical conditions, indicated the occurrence of aerobic respiration, denitrification, iron reduction, manganese reduction and sulfate reduction. The calculated BTEX expressed biodegradation capacity ranged between 20.52 and 33.67 mg/L, which appeared effective for the reduction of the contaminants levels. The contribution of each electron accepting process to the total biodegradation was in the order: denitrification > iron reduction > sulfate reduction > aerobic respiration > manganese reduction. The BTEX and benzene point attenuation rates were 0.0058-0.0064 and 0.0005-0.0032 day^-1, respectively, and the remediation time was 0.7-1.2 and 2.5-30 years, respectively. The BTEX and benzene bulk attenuation rates were 8.69 × 10^-4 and 1.05 × 10^-3 day^-1, respectively, and the remediation times for BTEX and benzene were 7.2 and 17.5 years, respectively. However, most of the natural attenuation occurring in this site can be attributed to dilution and dispersion. Consequently, the biodegradation and natural attenuation capacities were good enough to lower the contaminants levels, but their rates appeared to be insufficient to reach the remediation goal within a reasonable time frame. Therefore, some active remedial measures would be required.     

趋势分析法评价苯系物标准气体的时间稳定性

根据GB/T 15000.3—2008设计了苯系物标准气体的时间稳定性研究方案,制备了4瓶苯系物标准气体,随着时间的推移进行测定并将结果制图,结果显示量值随时间没有显著的变化趋势。以线性关系为模型,计算线性直线的斜率和斜率的标准偏差,用t检验判断斜率是否显著来评价标准气体的稳定性。计算结果显示,所有斜率均不显著,因此该研究制备的苯系物标准气体能够稳定保存22个月。根据时间稳定性数据计算由不稳定性引起的不确定度,并讨论了这种计算不稳定性引起不确定度的方法对结果有放大的可能性。     

Cation exchange in a glacial till drumlin at a road salt storage facility

At a former wood preservation plant severely contaminated with coal tar oil, in situ bulk attenuation and biodegradation rate constants for several monoaromatic (BTEX) and polyaromatic hydrocarbons (PAH) were determined using (1) classical first order decay models, (2) Michaelis–Menten degradation kinetics (MM), and (3) stable carbon isotopes, for o-xylene and naphthalene. The first order bulk attenuation rate constant for o-xylene was calculated to be 0.0025 d^− 1 and a novel stable isotope-based first order model, which also accounted for the respective redox conditions, resulted in a slightly smaller biodegradation rate constant of 0.0019 d^− 1. Based on MM-kinetics, the o-xylene concentration decreased with a maximum rate of k_max = 0.1 µg/L/d. The bulk attenuation rate constant of naphthalene retrieved from the classical first order decay model was 0.0038 d^− 1. The stable isotope-based biodegradation rate constant of 0.0027 d^− 1 was smaller in the reduced zone, while residual naphthalene in the oxic part of the plume further downgradient was degraded at a higher rate of 0.0038 d^− 1. With MM-kinetics a maximum degradation rate of k_max = 12 µg/L/d was determined. Although best fits were obtained by MM-kinetics, we consider the carbon stable isotope-based approach more appropriate as it is specific for biodegradation (not overall attenuation) and at the same time accounts for the dominant electron-accepting process. For o-xylene a field based isotope enrichment factor ε_field of − 1.4 could be determined using the Rayleigh model, which closely matched values from laboratory studies of o-xylene degradation under sulfate-reducing conditions.     

A strategy for aromatic hydrocarbon bioremediation under anaerobic conditions and the impacts of ethanol: a microcosm study

Increased use of ethanol-blended gasoline (gasohol) and its potential release into the subsurface have spurred interest in studying the biodegradation of and interactions between ethanol and gasoline components such as benzene, toluene, ethylbenzene and xylene isomers (BTEX) in groundwater plumes. The preferred substrate status and the high biological oxygen demand (BOD) posed by ethanol and its biodegradation products suggests that anaerobic electron acceptors (EAs) will be required to support in situ bioremediation of BTEX. To develop a strategy for aromatic hydrocarbon bioremediation and to understand the impacts of ethanol on BTEX biodegradation under strictly anaerobic conditions, a microcosm experiment was conducted using pristine aquifer sand and groundwater obtained from Canadian Forces Base Borden, Canada. The initial electron accepter pool included nitrate, sulfate and/or ferric iron. The microcosms typically contained 400 g of sediment, 600 approximately 800 ml of groundwater, and with differing EAs added, and were run under anaerobic conditions. Ethanol was added to some at concentrations of 500 and 5000 mg/L. Trends for biodegradation of aromatic hydrocarbons for the Borden aquifer material were first developed in the absence of ethanol, The results showed that indigenous microorganisms could degrade all aromatic hydrocarbons (BTEX and trimethylbenzene isomers-TMB) under nitrate- and ferric iron-combined conditions, but not under sulfate-reducing conditions. Toluene, ethylbenzene and m/p-xylene were biodegraded under denitrifying conditions. However, the persistence of benzene indicated that enhancing denitrification alone was insufficient. Both benzene and o-xylene biodegraded significantly under iron-reducing conditions, but only after denitrification had removed other aromatics. For the trimethylbenzene isomers, 1,3,5-TMB biodegradation was found under denitrifying and then iron-reducing conditions. Biodegradation of 1,2,3-TMB or 1,2,4-TMB was slower under iron-reducing conditions. This study suggests that addition of excess ferric iron combined with limited nitrate has promise for in situ bioremediation of BTEX and TMB in the Borden aquifer and possibly for other sites contaminated by hydrocarbons. This study is the first to report 1,2,3-TMB biodegradation under strictly anaerobic condition. With the addition of 500 mg/L ethanol but without EA addition, ethanol and its main intermediate, acetate, were quickly biodegraded within 41 d with methane as a major product. Ethanol initially present at 5000 mg/L without EA addition declined slowly with the persistence of unidentified volatile fatty acids, likely propionate and butyrate, but less methane. In contrast, all ethanol disappeared with repeated additions of either nitrate or ferric iron, but acetate and unidentified intermediates persisted under iron-enhanced conditions. With the addition of 500 mg/L ethanol and nitrate, only minor toluene biodegradation was observed under denitrifying conditions and only after ethanol and acetate were utilized. The higher ethanol concentration (5000 mg/L) essentially shut down BTEX biodegradation likely due to high EA demand provided by ethanol and its intermediates. The negative findings for anaerobic BTEX biodegradation in the presence of ethanol and/or its biodegradation products are in contrast to recent research reported by Da Silva et al. [Da Silva, M.L.B., Ruiz-Aguilar, G.M.L., Alvarez, P.J.J., 2005. Enhanced anaerobic biodegradation of BTEX-ethanol mixtures in aquifer columns amended with sulfate, chelated ferric iron or nitrate. Biodegradation. 16, 105-114]. Our results suggest that the apparent conservation of high residual labile carbon as biodegradation products such as acetate makes natural attenuation of aromatics less effective, and makes subsequent addition of EAs to promote in situ BTEX biodegradation problematic.     

Serious BTEX pollution in rural area of the North China Plain during winter season

Atmospheric BTEX compounds(benzene, toluene, ethylbenzene and xylenes) in a rural site of the North China Plain(NCP) were preliminarily investigated in winter, and the outdoor concentrations(25.8–236.0 μg/m3) were found to be much higher than those reported in urban regions. The pollution of BTEX inside a farmer's house was even more serious, with combined concentrations of 254.5–1552.9 μg/m3. Based on the ratio of benzene to toluene(1.17 ± 0.34) measured, the serious BTEX pollution in the rural site was mainly ascribed to domestic coal combustion for heating during the winter season. With the enhancement of farmers' incomes in recent years, coal consumption by farmers in the NCP is rapidly increasing to keep their houses warm, and hence the serious air pollution in rural areas of the NCP during winter, including BTEX, should be paid great attention.     

典型印染废水处理过程中芳香烃化合物的污染特征及污泥生态风险评价

采用GC-MS测定了典型综合印染废水处理厂废水和污泥中芳香烃化合物的含量.结果表明,原水中苯系物总量为203.96±15.18μg·L-1,其中二甲苯占62.7%,尾水中苯系物总量为0.2±0.029μg·L-1,整个处理工艺对苯系物的去除效率为99%.原水中多环芳烃(PAHs)总浓度达1349.51±35.77 ng·L-1,以3—6环为主,主要富集在颗粒物上.整个工艺对PAHs的去除效率为95%,尾水中PAHs总浓度为65.81±20.99ng·L-1,以2—3环为主.干污泥中PAHs含量高达2996.10±151.0 ng·g-1,污泥吸附为水相中PAHs去除的主要机理之一.印染污泥直接填埋或农用会引起潜在的生态危害.