长江三峡柑桔的冻害和热害（二）

本文从柑桔冻害和热害的危害因子和指标等级划分的研究和选取入手,着重探讨了长江三峡地区(湖北境内)两害显著的时空变化特征、差异与关联性及对柑桔生产的影响;揭示了80年代以来冬暖春热的重大气候变化是使两害向“两极分化”的根本原因;讨论了三峡水利工程对两害时空格局的可能调整及减灾原理;最后提出了可能的对策。     

高原高寒污水处理系统的微生物群落特征

为研究高原高寒污水处理系统活性污泥的微生物群落结构及多样性,以拉萨、云南、四川的3座高原污水厂作为实验组,同时以重庆2座非高原污水厂作为对照,采用PCR-DGGE技术对比分析了高原与非高原污水厂的微生物特性.研究表明：高原污水厂样品与非高原样品在聚类中展现出了较为疏远的关系,微生物群落区别明显.受强紫外线辐照的抑制,高原高寒污水处理系统微生物多样性的平均水平显著低于非高原污水厂,较低的微生物多样性是导致高原高寒地区污染物去除效果不佳的一项重要原因.群落构成方面,共鉴定出16个优势菌属,对应Proteobacteria、Bacteroidetes、Firmicutes、Verrucomicrobia 4个门.组间差异分析结果发现,高原组中丰度显著偏高的菌属只有Prosthecobacter,该菌在污水厂内分布广泛,且能够适应高原低温的条件.对于大多数活性污泥微生物而言,高原强紫外线是不利的生存条件.因此,减少高原露天污水处理系统的紫外辐照,是提升污水处理效能的一个潜在措施.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

硅胶表面TEOS疏水化改性及吸附VOCs特性

以正硅酸乙酯（TEOS）为疏水改性剂,通过硅胶表面的羟基接枝反应,得到具备一定疏水性的改性硅胶;利用BET、FT-IR、XRD和TG-DTG等手段对改性硅胶的结构及稳定性进行了表征;在此基础上考察了改性硅胶对各类有机废气的吸附性能.结果表明,TEOS成功接枝在了硅胶表面,改性硅胶不仅具备一定的疏水性,而且机械强度增加到原来的66.85%,稳定性也都得到了提高; 550℃空气下焙烧后的改性硅胶仍具有疏水性且吸附容量是焙烧之前的2倍;在高湿度高浓度的废气治理中,TEOS改性硅胶表现出更高的吸附能力和优良的热再生性能.高浓度下改性硅胶的吸附容量是低浓度下的10倍且不受水汽的影响;改性硅胶循环10次的吸附/脱附几乎不变,且在一定条件下,15~30min就达到90%的脱附率.     

磁性氧化石墨处理乳化含油废水及磁致增强效应

以高铁酸钾为氧化剂,基于改进Hummers法制备了新型磁性氧化石墨材料,在SEM、FTIR、氮气吸脱附和表面接触角表征基础上,探究了该材料处理乳化含油废水的效果及磁致增强效应.结果表明：相较于石墨,磁性氧化石墨比表面积增大,表面有卷曲结构并负载着Fe₃O₄颗粒,具有含氧官能团,存在疏水性较强的微观孔隙结构.在外加磁场条件下,磁性氧化石墨团聚,形成疏水性宏观孔隙结构,利于乳化油滴的吸附和附着.磁性氧化石墨处理乳化含油废水的能力远好于石墨与粉末活性炭,且处理效率与磁场强度成正相关,COD去除率可达95%以上.使用后的磁性氧化石墨进行溶剂萃取或热处理,可以循环使用.磁性氧化石墨经过4次循环使用,热再生效率为92%,溶剂萃取再生效率为86%.以上研究为乳化含油废水的处理提供了一种有效的方法.     

Multipoint source method in air pollution modelling of cold start emission

The paper presents a new method of air pollution modelling on a micro scale. For estimation of concentration of car exhaust pollutants, each car is treated as an instantaneous moving emission source. This approach enables us to model time and spatial changes of emission, especially during cold and cool start of an engine. These stages of engine work are a source of significant pollution concentration in urban areas. In this work, two models are proposed: one for the estimation of emission after cold start of the engine and another for the prediction of pollutant concentration. The first model (defined for individual exhaust gas pollutants) enables us to calculate the emission as a function of time after the cold or cool start, ambient temperature and average speed of motion. This model uses the HBEFA database. The second mathematical model is developed in order to calculate the pollutant dispersion and concentrations. The finite volume method is applied to discretise the set of partial differential equations describing wind flow and pollutant dispersion in the domain considered. Models presented in this paper can be called short-term models on a small spatial scale. The results of numerical simulation of pollutant emission and dispersion are also presented.     

钢门框型材冷弯成形工艺

介绍了不对称钢门框型材孔型设计中工艺参数、变形方式的选择方法     

废旧塑料回收利用技术

从我国废塑料回收利用的现状出发 ,分析了今后我国废塑料回收利用技术的发展趋势和应采取的措施 ,指出了废塑料回收利用的重要性。     

应用低温等离子体技术治理空气污染研究进展

低温等离子体技术在治理空气污染方面以其效率高、能耗低、适用范围广等特点而成为研究热点.本文介绍了低温等离子体的概念及分类,概述了国内外利用单一低温等离子体技术及其与吸附、催化协同、多性能颗粒混合物结合治理空气污染的最新进展,指出了存在的问题并讨论了今后的研究方向和应用前景.     

冷拉螺旋叶片展开的精确算法

提出了一种新的、更趋精确合理的关于冷拉螺旋叶片坯料的展开与放样计算方法 ,并从实践中探索出叶片在展开与放样时其内径的精确修正系数k之值。