普伐他汀的光催化降解性能及机理研究

通过水热法合成Bi₂WO₆,并利用XPS,XRD,BET,UV-Vis和SEM等方法对样品进行了表征;通过光催化性能实验考察了Bi₂WO₆投加量,溶液pH值对普伐他汀（PR）降解效果的影响;通过自由基捕获实验及中间产物的鉴定探明了Bi₂WO₆光催化降解PR过程的主要活性自由基,中间产物及降解机理,并采用发光细菌急性毒性试验评估了PR降解前后的毒性.结果表明,所制备的Bi₂WO₆是由大量纳米片组成的正交晶系花瓣状微球,各元素物质的量比为Bi：W：O=2.5：1：6.7,比表面积为26.67m²/g,带隙能为2.74eV;光催化性能结果表明,对于10mg/L PR,当溶液pH=6.5,Bi₂WO₆投加量为0.4g/L时降解效果最佳,降解率可达80.6%,矿化度为40.2%;自由基捕获实验结果表明降解过程中h⁺起主要的氧化作用,·OH和·O₂^-的氧化起辅助作用.基于活性自由基和中间产物的鉴别结果提出了Bi₂WO₆光催化降解PR的机理,即以h⁺为主,·OH和·O₂^-为辅联合攻击PR分子中C－C键,C＝C双键,酯键等化学键,进而将其分解为易降解小分子有机物.另外,毒性测试结果表明PR经光催化降解后的小分子产物与PR原液相比毒性并没有增强.     

Photocatalytic degradation of phenol

In this study photocatalytic degradation of phenol in thepresence of UV irradiated TiO₂ catalyst andH₂O₂was investigated. Effects of TiO₂ andH₂O₂concentrations and pH on photocatalytic degradation were examined. The rate constants for photocatalytic degradation wereevaluated as a function of TiO₂ and H₂O₂ concentrations and pH of the solution. It was found thatphotodegradation is an effective method for the removal of phenoland disappearance of phenol obeyed first order kinetics. The amount of CO₂h produced during photocatalytic degradation wascorresponding to the complete mineralization. Photodegradationcan be an alternative method for the treatment of phenol containing wastewaters.     

Modeling photocatalytic destruction of the organic contaminants in continuous stir flow reactor

Thin-film technique is becoming an industry standard for the preparation of TiO₂-based photocatalyst for organic destruction. The catalyst provides several advantages over the conventional powder TiO₂ in the treatment of wastewater and groundwater. In this study, a continuous stir flow reactor model is developed capable of describing the photocatalytic process. The model incorporates the following fundamental mechanisms: adsorption, diffusion, liquid-film transfer, UV attenuation, and photocatalytic reaction. All of the simulation results indicate that there exists a highly nonlinear relation between each of these parameters and the destruction rate. Various incident light intensities also are incorporated to simulate the energy efficiency. The simulations illustrate that the photocatalytic model can be used to elucidate the effect of process variables. It is also possible to “custom-design” a catalyst for the treatment of a particular waste stream.     

Al_2O_3光催化降解染料性能研究

液相加热法制备了Al2O3作为光催化剂,研究了不同光源、光照时间、催化剂用量和溶液酸度等条件对常见有机染料光催化降解性能影响。结果表明,用太阳光作为光源照射3h,50mL染料溶液中加入Al2O3 30mg,溶液pH8～10,孔雀石绿,酚藏花红,甲基紫等染料脱色率达93%以上。将使用过的Al2O3经过简单处理,孔雀石绿溶液脱色率仍达到94.1%,催化性能稳定,可以重复利用。通过紫外可见光谱分析,表明染料分子在催化剂和光照条件下发生了降解。     

Fulvic acid removal by nanoparticle TiO2 using a submerged membrane photocatalysis reactor

The degradation of fulvic acid（FA） by nanoparticle TiO2 in a submerged membrane photocatalysis（SMPC） reactor was studied. In this reactor, photocatalytic oxidation and membrane separation co-occured. The continuous air supplier provided O2 for the photocatalytical reaction and mixed the solution through an airflow controller. The particle TiO2 could automatically settle due to gravity without particle agglomeration so it could be easily separated by microfiltration（MF） membrane. It was efficient to maintain high flux of membranes. The effects of operational parameters on the photocatalytic oxidation rate of FA were investigated. Results indicated that photocatalyst at 0.5 g/L and airflow at 0.06 m^3/h were the optimum condition for the removal of fulvic acid, the removal efficiency was higher in acid media than that in alkaline media. The effects of different filtration duration on permeate flux rate of MF with P25 powder and with nanoparticle TiO2 were compared. Experimental results indicated that the permeate flux rate of MF was improved and the membrane fouling phenomenon was reduced with the addition of nanoparticle TiO2 catalyst compared with conventional P25 powder. Therefore, this submerged membrane photocatalysis reactor can faciliate potential application of photocatalytic oxidation process in drinking water treatment.     

UV/TiO_2膜深度处理垃圾渗滤液的研究

研究了以固定相TiO2为催化剂光催化降解垃圾渗滤液中有机污染物的可行性。试验了制备TiO2膜的适宜条件以及光照时间等各种因素对COD的去除率和UV335脱色率的影响。研究表明,COD为418mg/L的垃圾渗滤液经400W高压汞灯光照30min,COD的去除率和UV335脱色率分别为44.3%和75.0%。光照时间60min时,COD的去除率和UV335脱色率可提高至54%和90%。光照30min后与活性炭柱联用,COD的去除率和UV335脱色率分别提高到68.3%和84.6%。     

新型负载型纳米TiO_2光催化降解苯酚的试验研究

以岩棉为载体制备一种新型负载型纳米TiO2,对有机污染物苯酚的降解效果较好。岩棉对苯酚有一定的吸附作用。经过120min的处理,苯酚基本上被完全降解。流速对降解率的影响较大,本试验选择流速为5mL/min。初始浓度越小,苯酚的降解效果越好。通入O2和加入适量H2O2均有利于苯酚的降解,且少量的H2O2可使苯酚的降解率大大提高。苯酚在pH=4.5时降解效果最好。     

纳米复合GeO2/TiO2的制备及光催化性能研究

采用改进的Sol-gel方法,制备了一种新型的单分散椭球形微孔结构的纳米GeO2/TiO2复合光催化剂,并用TG-DTA、XRD、XPS、UV-vis、FT-IR、TEM、BET等手段进行了表征.以难生化降解的染料罗丹明B为目标降解物,采用HPLC测定不同光照时间下催化剂对染料降解的情况,考察了催化剂的光催化活性结果表明,改进的Sol-gel法制得的复合光催化剂具有明显的孔结构,而且比表面积大、粒径小、粒径分布窄、分散性好;与适量GeO2复合后能够有效提高TiO2纳米粒子的光催化活性;复合光催化剂的最佳制备条件为GeO2摩尔含量为0.1%,煅烧温度为400℃,所制得的GeO2/TiO2光催化活性比纯TiO2有显著提高.     

太阳能光催化降解法去除水中罗丹明染料的研究

在太阳光的紫外线辐射下，应用载有ＴｉＯ２薄层的平板式光催化反应器，进行了光催化降解法去除水中罗丹明染料的试验，结果表明，当紫外线辐射强度平均为３３Ｗ／ｍ＾２，反应时间为１８ｍｉｎ时，水中罗丹明染料浓度由１０ｍｇ／Ｌ降至０．０１ｍｇ／Ｌ，在室国家排放标准，探讨了太阳能光催化反应系统的改进方向及工业化应用的有关问题。     

TiO2光催化氧化的研究进展

概述了TiO2光催化氧化降解水中污染物的原理及TiO2光催化剂的制备，提出了增强其活性的途径。TiO2光催化氧化可应用于印染、农药、造纸等工业废水及饮用水处理中，研制高效的负栽型纳米TiO2光催化剂、解决太阳能利用问题、开发多功能光催化反应器是今后TiO2光催化氧化的发展趋势。