Transport of chlorinated dioxins and furans in soil columns: modeling pentachlorophenol pole-treating oil influence

Column experiments were conducted to validate a screening model predicting the influence of pentachlorophenol (PCP) pole-treating oil on the vertical migration of its impurities, chlorinated dioxins and furans (PCDD/Fs). PCP pole-treating oil (15 mL d⁻¹) and water (20 mL d⁻¹) were added daily to the top of sand and organic soil columns during 35 d. Column soil samples were analyzed to determine concentrations of hydrocarbons and PCDD/Fs at several depths in the columns (0-30 cm) and their evolution in time (7, 14, 21 and 35 d).The model predicted a significant vertical migration of PCDD/Fs due to the presence of oil as a free phase and PCDD/Fs were found in the different column layers at concentrations consistent with model predictions (same order of magnitude). Measured PCDD/Fs concentrations are in total disagreement with literature data and with model prediction in the absence of oil free phase, which implies PCDD/F properties alone cannot be used to predict their fate in the current context: the influence of PCP pole-treating oil must be accounted for to properly explain their migration.     

Significance of Regional Source Contributions to Urban PM-10 Concentrations

Based on data collected in St. Louis, Philadelphia and other eastern U.S. cities, we conclude that a significant fraction of the PM-10 concentration is "background." In these urban areas the background fraction ranges from 35 to 80 percent of the daily, monthly or annual concentration. The bulk of the background appears to be of regional origin. The average chemical makeup of eastern U.S. PM-10 is sulfate as SO₄, 21-34 percent; crustal material, 14-39 percent; "unknown" (carbonaceous matter, ammonium, nitrate and water), 36-51 percent, all of which is difficult to apportion to specific sources. Dispersion modeling using a local source inventory can account only for a small portion of the total PM-10 mass. Emission roll-back of local sources may have a limited effect on reducing total concentrations of PM-10.     

Sisal/Carbon Fibre Reinforced Hybrid Composites: Tensile, Flexural and Chemical Resistance Properties

The variation of mechanical properties such as tensile and flexural properties of randomly oriented unsaturated polyester based sisal/carbon fibre reinforced hybrid composites with different fibre weight ratios have been studied. The chemical resistance test of these hybrid composites to various solvents, acids and alkalies were studied. The effect of NaOH treatment of sisal fibres on the tensile, flexural and chemical resistance properties of these sisal/carbon hybrid composites has also been studied. The hybrid composites showed an increase in tensile and flexural properties with increase in the carbon fibre loading. The tensile properties and flexural properties of these hybrid composites have been found to be higher than that of the matrix. Significant improvement in tensile properties and flexural properties of the sisal/carbon hybrid composites has been observed by alkali treatment. The chemical resistance test results showed that these untreated and alkali treated hybrid composites are résistance to all chemicals except carbon tetra chloride. Hand lay-up technique was used for making the composites and tests are carried out by using ASTM methods.     

Chemical fluxes in time through forest ecosystems in the UK - Soil response to pollution recovery

Long term trend analysis of bulk precipitation, throughfall and soil solution elemental fluxes from 12 years monitoring at 10 ICP Level II forest sites in the UK reveal coherent national chemical trends indicating recovery from sulphur deposition and acidification. Soil solution pH increased and sulphate and aluminium decreased at most sites. Trends in nitrogen were variable and dependant on its form. Dissolved organic nitrogen increased in bulk precipitation, throughfall and soil solution at most sites. Nitrate in soil solution declined at sites receiving high nitrogen deposition. Increase in soil dissolved organic carbon was detected - a response to pollution recovery, changes in soil temperature and/or increased microbial activity. An increase of sodium and chloride was evident - a possible result of more frequent storm events at exposed sites. The intensive and integrated nature of monitoring enables the relationships between climate/pollutant exposure and chemical/biological response in forestry to be explored.     

Assessment of dietary exposure to PCDD/F and dioxin-like PCB in infant formulae available on the EU market

In infant period, human milk and infant formulae are the major sources of exposure to dioxins (polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDFs) and dioxin-like polychlorinated biphenyls (PCB). Since in many parts of Europe the mothers are increasingly reluctant to breastfeed their babies, the main objective of the present study is to assess the level of exposure of non-breast-fed infants during their early development. Consequently, the concentration levels of PCDD/F and dioxin-like PCB were determined in industrial infant formulae including "starting" (aged 0-4months) and "follow-on" (after 4months) products of milk formula, soy formula and hypoallergenic infant formula, available on the EU market. Furthermore, dietary exposure to dioxin of exclusively formula-fed infants was assessed at each month from 0 to 9months. The results suggest that dietary exposure to dioxins via formulae is higher when consuming "starting" than "follow-on" infant formulae on a body-weight basis. Estimated dietary exposure after 4months of age was always below the lowest range of the Tolerable Daily Intake (TDI) of 1pg WHO-TEQkg(-1)bwd(-1) and Provisional Tolerable Monthly Intake (PTMI) of 70pg WHO-TEQkg(-1)bwmonth(-1). The highest estimated cumulative dietary exposure to PCDD/F and dioxin-like PCB was obtained considering infants of 0-1months fed with the "starting" hypoallergenic infant formula (2.8pg WHO-TEQkg(-1)bwd(-1) and 84pg WHO-TQkg(-1)bwmonth(-1)). However, these elevated levels are much lower than those observed in some studies in breast-fed infants. The study can be used for further risk assessments in regard to infant exposure.     

Integrating science and business models of sustainability for environmentally-challenging industries such as secondary lead smelters: A systematic review and analysis of findings

Secondary lead smelters (SLS) represent an environmentally-challenging industry as they deal with toxic substances posing potential threats to both human and environmental health, consequently, they operate under strict government regulations. Such challenges have resulted in the significant reduction of SLS plants in the last three decades. In addition, the domestic recycling of lead has been on a steep decline in the past 10 years as the amount of lead recovered has remained virtually unchanged while consumption has increased. Therefore, one may wonder whether sustainable development can be achieved among SLS. The primary objective of this study was to determine whether a roadmap for sustainable development can be established for SLS. The following aims were established in support of the study objective: (1) to conduct a systematic review and an analysis of models of sustainable systems with a particular emphasis on SLS; (2) to document the challenges for the U.S. secondary lead smelting industry; and (3) to explore practices and concepts which act as vehicles for SLS on the road to sustainable development.An evidence-based methodology was adopted to achieve the study objective. A comprehensive electronic search was conducted to implement the aforementioned specific aims. Inclusion criteria were established to filter out irrelevant scientific papers and reports. The relevant articles were closely scrutinized and appraised to extract the required information and data for the possible development of a sustainable roadmap. The search process yielded a number of research articles which were utilized in the systematic review. Two types of models emerged: management/business and science/mathematical models. Although the management/business models explored actions to achieve sustainable growth in the industrial enterprise, science/mathematical models attempted to explain the sustainable behaviors and properties aiming at predominantly ecosystem management. As such, there are major disconnects between the science/mathematical and management/business models in terms of aims and goals. Therefore, there is an urgent need to integrate science and business models of sustainability for the industrial enterprises at large and environmentally-challenging industrial sectors in particular. In this paper, we offered examples of practices and concepts which can be used in charting a path towards sustainable development for secondary lead smelters particularly that the waste generated is much greater outside the industrial enterprise than inside.An environmentally-challenging industry such as secondary lead smelters requires a fresh look to chart a path towards sustainable development (i.e., survivability and purposive needs) for all stakeholders (i.e., industrial enterprise, individual stakeholders, and social/ecological systems). Such a path should deal with issues beyond pollution prevention, product stewardship and clean technologies.     

Predicting molybdenum toxicity to higher plants: Estimation of toxicity threshold values

Four plant species (oilseed rape, Brassica napus L.; red clover, Trifolium pratense L.; ryegrass, Lolium perenne L.; and tomato, Lycopersicon esculentum L.) were tested on ten soils varying widely in soil properties to assess molybdenum (Mo) toxicity. A larger range (66-fold-609-fold) of added Mo concentrations resulting in 50% inhibition of yield (ED₅₀) was found among soils than among plant species (2-fold-38-fold), which illustrated that the soils differed widely in the expression of Mo toxicity. Toxicity thresholds based on soil solution Mo narrowed the variation among soils compared to thresholds based on added Mo concentrations. We conclude that plant bioavailability of Mo in soil depends on Mo solubility, but this alone did not decrease the variability in observed toxicity enough to be used in risk assessment and that other soil properties influencing Mo toxicity to plants need to be considered.     

Printed wiring boards for mobile phones: characterization and recycling of copper

The popularization of mobile phones, combined with a technological evolution, means a large number of scrap and obsolete equipment are discarded every year, thereby causing economic losses and environmental pollution. In the present study, the printed wiring boards scrap of mobile phones were characterized in order to recycle some of the device components, using techniques of mechanical processing, hydrometallurgy and electrometallurgy. The use of the techniques of mechanical processing (milling, particle size classification, magnetic and electrostatic separation) was an efficient alternative to obtain a concentrated fraction (mainly iron in the magnetic fraction and copper in the conductive fraction) and another fraction containing polymers and ceramics. At the end of mechanical processing, a concentrated fraction of metals could be obtained with an average concentration of 60% copper. This concentrated fraction in metals was dissolved in aqua regia and sent to electrowinning to recover 92% of the dissolved copper. The obtained cathodes have a copper content above 95%, which demonstrates the technical feasibility of recovery of copper using the techniques of mechanical processing, hydrometallurgy and electrometallurgy.