The influence of pH on cadmium toxicity to the green alga Stichococcus bacillaris and on the cadmium forms present in the culture medium

Cadmium toxicity to the green alga Stichococcus bacillaris was investigated in media of pH 3-9. A significant decrease of cadmium toxicity occurred in both the acidic and alkaline ranges of pH. In media of pH 3 and 9, cadmium did not affect the dry mass content substantially. Maximum toxicity of cadmium was noticed at pH 6-7. Voltametric investigations showed a significant effect of pH on electrochemically measured cadmium content in the culture media. Hydrolysis of the medium components and formation of cadmium complexes with OH(-) ions caused a considerable decrease in amounts of electrochemically measured cadmium in the alkaline range of pH.     

Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.     

Soil sampling and analysis for volatile organic compounds

Concerns over data quality have raised many questions related to sampling soils for volatile organic compounds (VOCs). This paper was prepared in response to some of these questions and concerns expressed by Remedial Project Managers (RPMs) and On-Scene Coordinators (OSCs). The following questions are frequently asked:

1. Is there a specific device suggested for sampling soils for VOCs?
2. Are there significant losses of VOCs when transferring a soil sample from a sampling device (e.g., split spoon) into the sample container?
3. What is the best method for getting the sample from the split spoon (or other device) into the sample container?
4. Are there smaller devices such as subcore samplers available for collecting aliquots from the larger core and efficiently transferring the sample into the sample container?
5. Are certain containers better than others for shipping and storing soil samples for VOC analysis?
6. Are there any reliable preservation procedures for reducing VOC losses from soil samples and for extending holding times?

Guidance is provided for selecting the most effective sampling device for collecting samples from soil matrices. The techniques for sample collection, sample handling, containerizing, shipment, and storage described in this paper reduce VOC losses and generally provide more representative samples for volatile organic analyses (VOA) than techniques in current use. For a discussion on the proper use of sampling equipment the reader should refer to other sources (Acker, 1974; U.S. EPA, 1983; U.S. EPA, 1986a). Soil, as referred to in this report, encompasses the mass (surface and subsurface) of unconsolidated mantle of weathered rock and loose material lying above solid rock. Further, a distinction must be made as to what fraction of the unconsolidated material is soil and what fraction is not. The soil component here is defined as all mineral and naturally occurring organic material that is 2 mm or less in size. This is the size normally used to differentiate between soils (consisting of sands, silts, and clays) and gravels. Although numerous sampling situations may be encountered, this paper focuses on three broad categories of sites that might be sampled for VOCs:

1. Open test pit or trench.
2. Surface soils (<5 ft in depth).
3. Subsurface soils (>5 ft in depth).

     

Analysing the sensitivity behaviour of two hydrology models

Recently, the New Morris Method has been presented as an effective sensitivity analysis tool for mathematical models. The New Morris Method estimates the sensitivity of an output parameter to a given set of input parameters (first-order effects) and the extent these parameters interact with each other (second-order effects). This method requires the specification of two parameters (runs and resolution) that control the sampling of the output parameter to determine its sensitivity to various inputs. The criteria for these parameters have been set on the analysis of a well-behaved analytical function (see Cropp and Braddock, Reliab. Eng. Syst. Saf. 78:77–83, 2002), which may not be applicable to other physical models that describe complex processes. This paper will investigate the appropriateness of the criteria from (Cropp and Braddock, 2002) and hence the effectiveness of the New Morris Method to determine the sensitivity behaviour of two hydrologic models: the Soil Erosion and Deposition System and Griffith University Representation of Urban Hydrology. In the first case, this paper will separately analyse the sensitivity of an output parameter on a set of input parameters (first- and second-order effects) for each model and discuss the physical meaning of these sensitivities. This will be followed by an investigation into the sampling criteria by exploring the convergence of the sensitivity behaviour for each model as the sampling of the parameter space is increased. By comparing these trends to the convergence behaviour from Cropp and Braddock (2002), we will determine how well the New Morris Method estimates the sensitivity for each model and whether the sampling criteria are appropriate for these models. It will be shown that the New Morris Method can provide additional insight into the functioning of these models, and that, under a different metric, the sensitivity behaviour of these models does converge confirming the sampling criteria set by Cropp and Braddock.     

超临界二氧化碳萃取－GC／MS测定土壤中的多环芳烃

本文开发了一种采用超临界二氧化碳萃取土壤中多环芳烃、不须经过纯化步骤，直接可用于ＧＣ／ＭＳ分析的简便、高效的方法。本实验中超临界革取的流体是二氧化碳，改善剂是５％的二氯甲烷／甲醇，萃取温度为１２０℃、压力为３４ＭＰａ。ＧＣ／ＭＳ分析时除了采用外标外，还加入了６种同位素ＰＡＨｓ内标以校正各段ＰＡＨｓ的响应因子。采用本方法成功地测定了我国未开垦森林土壤中的ＰＡＨｓ。     

Laboratory-polluted soils: a methodological approach to establish equilibrium conditions for different metal chemical forms in soils

An approach based on the number of extractions performed over time was applied to study the time necessary to attain equilibrium conditions between the different chemical forms present in two natural soils laboratory-loaded with heavy metals (Cu(II), Pb(II), Zn(II)). The influence of some soil parameters, such as pH value, cation exchange capacity and organic matter content, on the equilibrium time was evidenced both by the different nature of the soils and by the treatment of soils with paper mill sludge. Equilibrium conditions were determined by studying the metal partitioning in the soil on a case by case basis. The behaviour of the three metals was not the same, and the conditions of equilibrium among the different chemical forms were the result of the amount of heavy metals added as well as of the nature of the soil.     

Microbiological characteristics in a zero-valent iron reactive barrier

Zero-valent iron (Fe⁰)-based permeable reactive barriertreatment has been generating great interest for passivegroundwater remediation, yet few studies have paid particularattention to the microbial activity and characteristics withinand in the vicinity of the Fe⁰-barrier matrix. The presentstudy was undertaken to evaluate the microbial population andcommunity composition in the reducing zone of influence byFe⁰ corrosion in the barrier at the Oak Ridge Y-12 Plantsite. Both phospholipid fatty acids and DNA analyses were usedto determine the total microbial population and microbialfunctional groups, including sulfate-reducing bacteria,denitrifying bacteria, and methanogens, in groundwater andsoil/iron core samples. A diverse microbial community wasidentified in the strongly reducing Fe⁰ environment despitea relatively high pH condition within the Fe⁰ barrier (up topH 10). In comparison with those found in the backgroundsoil/groundwater samples, the enhanced microbial populationranged from 1 to 3 orders of magnitude and appeared to increase from upgradient of the barrier to downgradient soil. Inaddition, microbial community composition appeared to change overtime, and the bacterial types of microorganismsincreased consistently as the barrier aged. DNA analysisindicated the presence of sulfate-reducing and denitrifyingbacteria in the barrier and its surrounding soil. However, theactivity of methanogens was found to be relatively low,presumably as a result of the competition by sulfate/metal-reducing bacteria and denitrifying bacteria because of the unlimited availability of sulfate and nitrate in the site groundwater. Results of this study provide evidenceof a diverse microbial population within and in the vicinity ofthe iron barrier, although the important roles of microbial activity, either beneficially or detrimentally, on the longevityand enduring efficiency of the Fe⁰ barriers are yet to be evaluated.     

A national framework for monitoring and reporting on environmental sustainability in Canada

In 1991, a collaborative project to revise the terrestrial component of a national ecological framework was undertaken with a wide range of stakeholders. This spatial framework consists of multiple, nested levels of ecological generalization with linkages to existing federal and provincial scientific databases. The broadest level of generalization is the ecozone. Macroclimate, major vegetation types and subcontinental scale physiographic formations constitute the definitive components of these major ecosystems. Ecozones are subdivided into approximately 200 ecoregions which are based on properties like regional physiography, surficial geology, climate, vegetation, soil, water and fauna. The ecozone and ecoregion levels of the framework have been depicted on a national map coverage at 1:7 500 000 scale. Ecoregions have been subdivided into ecodistricts based primarily on landform, parent material, topography, soils, waterbodies and vegetation at a scale (1:2 000 000) useful for environmental resource management, monitoring and modelling activities. Nested within the ecodistricts are the polygons that make up the Soil Landscapes of Canada series of 1:1 000 000 scale soil maps. The framework is supported by an ARC-INFO GIS at Agriculture Canada. The data model allows linkage to associated databases on climate, land use and socio-economic attributes.     

Development of Ecological Land Classification and mapping in support of forest management in northern Newfoundland,Canada

For the sustainable development of forest land, as recently prescribed by the Canadian Forest Strategy, a land classification project in northern Newfoundland was initiated to support the local forest management activities. The method adopted here is a modification of the Canadian Committee for Ecological Land Classification's (CCELC) system, and it applies various levels of mapping to uniform areas based on geomorphology, soils, vegetation, climate, water, and fauna.In this study, all CCELC levels were mapped; resulting maps were digitized and imported into a Geographic Informations System (GIS). The GIS data base contained the following maps: 1) digital terrain model, 2) bedrock geology, 3) surficial geology, 4) forest inventory, and 5) various levels of the ecological land classification, including Vegetation Types at the lowest level. In addition to the mapping, mensurational data were analyzed to provide stand and stock tables for each of the forest types, including growth curves that could be entered into specific forest growth modelling systems to predict wood supply scenarios based upon different management interventions.     

Reduction of SO2 emissions by ammonia gas during unstaged combustion

The reduction of SO₂ by the addition of ammonia gas has been studied in a 2 m high fluidized bed combustor having a 30 cm static bed height and a freeboard height of 170 cm. Ammonia gas was injected at 52 cm above the distributor where the temperature is ca. 700° C by an uncooled stainless steel tube injector. Experiments were carried out to investigate the effects of amminia gas injection on sulphur dioxide emissions at unstaged conditions of: (i) excess air level, (ii) NH₃:SO₂ molar ratio, (iii) fluidizing velocity and (iv) bed height.A maximum reduction of 75% in SO₂ emissions was found at 40% excess air, at an NH₃:SO₂ molar ratio of 5.4. The onset of SO₂ reduction occurred at an NH₃:SO₂ ratio of 1.5 However, the most effective ratio was found to be between 3 and 5. Fluidizing velocity and bed height were also found to have significant influence on SO₂ reduction.It is difficult to determine how the SO₂ reduction varied with operating conditions. When ammonia is added in the main combustor zone, the temperature is much higher than that required for the occurrence of sulphur dioxide-ammonia and sulphur trioxide-ammonia reactions. However, this paper points out the significance of ammonia addition in the reduction of sulphur dioxide.