深圳大气PM2.5中水溶性有机物的来源特征

对2017年9月~2018年8月深圳市北部大气PM_2.5中水溶性有机物（WSOM）的质量浓度、质谱及来源结构进行测量和分析.结果表明：PM_2.5的质量浓度为（32.3±18.4）μg/m³,WSOM的质量浓度为（9.4±5.7）μg/m³,占颗粒物总有机物的（77.6%±14.0%）.质谱分析显示,WSOM的氧碳比（O/C）平均值达到（0.57±0.09）,属于二次有机物的O/C值范围,且生物质燃烧排放的离子碎片C₂H₄O₂⁺的丰度显著,说明WSOM的来源中有显著的生物质燃烧排放的有机气溶胶.为了明确WSOM的来源结构,利用正矩阵因子分解法（PMF）模型进行来源解析,发现3个合理因子：高氧化态有机气溶胶（MO-OOA）,低氧化态有机气溶胶（LO-OOA）和生物质燃烧（BBOA）,贡献比例分别为51.7%,31.8%和16.5%.MO-OOA和BBOA贡献浓度均呈现秋冬高、春夏低的季节变化特征,反向轨迹分析显示其与内陆污染传输关系密切.LO-OOA的变化相对稳定,本地源的贡献较大.结合¹⁴C同位素示踪法对秋冬季WSOM样品分析,发现机动车等化石源二次有机物是WSOM的主要来源,贡献比例达到53.9%,需继续加强对化石燃料控制来降低WSOM污染.     

裂解温度和离子强度对不同来源生物炭胶体释放行为的影响

近年来环境中生物炭胶体形成受到广泛关注,它是生物炭在环境中物理分解作用的重要过程,对污染物迁移有着重要影响.然而,目前对生物炭胶体释放过程和影响因素的研究甚少,人们对生物炭胶体释放机理的认识还很有限.本研究以小麦秸秆和花生壳为生物质来源,系统地探讨了生物炭的裂解温度（300~700 ℃）和溶液离子强度（0.1~10 mmol·L^-1）对生物炭胶体产率的影响.结果表明,随着裂解温度的升高,生物炭的耐磨性增强,且在较高的裂解温度下（≥500 ℃）花生壳生物炭的耐磨性显著强于小麦秸秆生物炭.生物炭的胶体产率受到生物质来源和裂解温度的显著影响,花生壳生物炭的胶体产率低于小麦秸秆生物炭,高温裂解（≥600 ℃）生物炭的胶体产率显著低于中低温裂解生物炭.在相同溶液离子强度下,生物炭胶体产率与其亚微米级碎片率呈显著正相关（p<0.05）,即生物炭中亚微米级碎片率越高,生物炭胶体产率越高.当溶液离子强度从1 mmol·L^-1增加到10 mmol·L^-1时,两种来源生物炭的胶体产率均显著降低,其降低的程度因生物炭裂解温度而异,其中低温裂解（300 ℃）生物炭的胶体产率降低了11.1%~11.2%,中高温裂解（≥ 500 ℃）生物炭的胶体产率降低了60.0%~97.2%.     

机动车轮胎磨损颗粒物化学组分特征研究

为研究机动车道路行驶过程中轮胎磨损排放的颗粒物理化特性,利用轮胎轮廓仿真磨耗仪,对国内主流17种轮胎胎面进行仿真磨耗实验,获得颗粒物样品,提取并检测其中18种元素和20种多环芳烃（PAHs）的含量.结果显示,元素和PAHs含量因轮胎品牌和速度等级的不同而差异显著.18种元素平均含量为（99.04±68.43）mg/g,占样品总重的9.90%,其中Si（88.97±67.85）mg/g、Zn（6.77±1.64）mg/g和Na（1.05±0.75）mg/g的平均含量均超过1mg/g,Cd的含量最低,为（0.43±0.31）μg/g.20种PAHs含量之和（∑20PAHs）在12.13~433.64 μg/g,平均为（94.13±110.18）μg/g,PY的平均含量最高（30.98±31.27）μg/g,其次是CHR、BaP、FA、PHE和BghiP,平均含量最低的是AC（0.58±0.2）μg/g;从环数看,以4环PAHs为主（占∑20PAHs的45.03%~67.93%）,其次为3环（平均含量为15.45%）和5环（平均含量为12.62%）.总体来说,国外品牌轮胎样品中元素和PAHs含量略高于国内品牌,而主要PAHs环数略低于国内品牌.     

陕北不同沟道土地盐碱化现状及影响因素

沟道土地是陕北黄土丘陵沟壑区重要的土地资源。然而,当前对黄土高原沟道土地的盐碱化问题关注不够,对盐碱化的现状、发生机制和防治措施也缺乏深入系统的认识,知识储备不能满足生产实际的需要。本文以陕北黄土丘陵沟壑区自然和人为形成的沟道土地为研究对象,分别是延安顾屯新造耕地(治沟造地)、延川马家湾淤地坝土地和子洲黄土洼天然古聚湫土地,在这些流域内沿沟道采集土壤样品,测定土壤的电导率(EC)、p H值、含水量及粒度,分析土壤盐碱化的现状和影响因子。结果表明:马家湾淤地坝土地盐碱化最为严重,流域中游至上游均出现不同程度的盐碱化;顾屯新造地上游出现盐碱化,盐碱化程度较马家湾轻,而黄土洼古聚湫全流域未出现盐碱化。地下水位较浅是沟道土地发生盐碱化的主要影响因素,因此陕北沟道土地盐碱化防治应着力控制地下水位,建设良好的排水系统,加强排水。     

悬浮填料投加对AnMBR性能及膜污染的影响

研究了悬浮填料投加对分置式厌氧膜生物反应器（AnMBR）的COD去除效果、污泥混合液特性及膜污染的影响。试验结果表明:在反应器有机负荷为2.09 kg/（m3·d）,污泥负荷为0.54 kg/（kg·d）,水力停留时间（HRT）为48 h,温度为（35±2）℃的条件下,与未投加悬浮填料阶段比较,投加填料后AnMBR的COD总去除率由96.6%提高至97.9%,甲烷产率提高16.0%。同时投加悬浮填料后AnMBR混合液污泥平均粒径增大,滤饼层阻力、总阻力、滤饼层阻力在总阻力中的占比较未投加悬浮填料时分别降低7.8、6.5和1.3百分点,溶解性胞外聚合物（SEPS）和结合性胞外聚合物（BEPS）浓度分别降低了20.5%和29.4%,跨膜压差（TMP）线性增长速率降低,膜污染速率明显减缓。因此,投加悬浮填料可在不增加能耗的情况下改善污泥混合液特性,起到强化AnMBR处理效果和控制膜污染的作用。     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

中国工业园区绿色发展政策对比分析及对策研究

为了提升我国工业园区绿色发展水平,对目前我国工业园区发展历程、现状特征进行了分析,对工业园区绿色发展政策进行了梳理和对比,并结合工业园区绿色发展中存在的问题提出了对策建议.研究表明:①我国工业园区经历了快速发展、调整发展和科学发展等阶段,在经济发展、资源与能源优化利用、污染减排等方面成效显著.②我国工业园区绿色发展的相关政策主要体现在国家生态工业示范园区创建、园区循环化改造、国家低碳工业园区试点、绿色园区建设和UNIDO绿色工业园区创建等工作中,这些政策在推动主体、实施路径、侧重方向上各不相同又各有特色,对推动工业园区节能减排绩效明显.③目前,我国工业园区绿色发展存在的问题主要表现在重视程度有待提升、风险防范意识有待加强、创新能力有待提高等方面.为此,提出了我国工业园区绿色发展对策建议:积极践行绿色发展理念,推进园区绿色化、生态化、低碳化建设,实现经济环境双赢;注意环境风险防控,确保环境安全;创新管理机制,强化监督管理.      

Plasmonic silver/silver oxide nanoparticles anchored bismuth vanadate as a novel visible-light ternary photocatalyst for degrading pharmaceutical micropollutants

The degradation of pharmaceutical micropollutants is an intensifying environmental problem and synthesis of efficient photocatalysts for this purpose is one of the foremost challenges worldwide. Therefore, this study was conducted to develop novel plasmonic Ag/Ag₂O/BiVO₄ nanocomposite photocatalysts by simple precipitation and thermal decomposition methods, which could exhibit higher photocatalytic activity for mineralized pharmaceutical micropollutants. Among the different treatments, the best performance was observed for the Ag/Ag₂O/BiVO₄ nanocomposites (5 wt.%; 10 min's visible light irradiation) which exhibited 6.57 times higher photodegradation rate than the pure BiVO₄. Further, the effects of different influencing factors on the photodegradation system of tetracycline hydrochloride (TC-HCl) were investigated and the feasibility for its practical application was explored through the specific light sources, water source and cycle experiments. The mechanistic study demonstrated that the photogenerated holes (h⁺), superoxide radicals (?O₂^?) and hydroxyl radicals (?OH) participated in TC-HCl removal process, which is different from the pure BiVO₄ reaction system. Hence, the present work can provide a new approach for the formation of novel plasmonic photocatalysts with high photoactivity and can act as effective practical application for environmental remediation.     

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.     

2015—2018年河南省辖海河流域水质改善效果评价

分别采用单因子评价法、综合污染指数评价法和模糊综合评价法对2015—2018年河南省辖海河流域的水质改善效果进行评价分析。结果表明:3种方法的评价结果基本一致,2015—2018年河南省辖海河流域整体水质呈现改善趋势。但各方法侧重点有所不同。单因子评价结果显示,海河流域21项污染因子Ⅰ—Ⅲ类数量占比由2015年的69.63%增加至2018年的89.52%,劣Ⅴ类占比由2015年的15.13%减少至2018年的0.85%;海河流域综合污染指数由2015年的0.89降低至2018年的0.56,水质级别由中度污染改善为轻度污染,其中卫河、共产主义渠、大沙河、安阳河、汤河、马颊河的水质状况均有一定改善;模糊评价结果显示,NH₃-N和TP在9项评价因子中权重占比较大,是河南省辖海河流域的主要污染因子;2018年8条河流均达到Ⅰ—Ⅲ类水质。前2种评价方法适用于管理分析,模糊评价法可补充说明河流存在的问题,更适用于研究工作。