氧活性粒子氧化NO生成HNO_3

采用强电离介质阻挡放电方法制取高浓度氧活性粒子(O+2、O3)并注入气体外排烟道中,实现O+2、O3氧化NO转化成资源酸(HNO3)的等离子化学反应。描述强电离放电的氧活性粒子产生器,讨论烟道中O+2、O3氧化NO成HNO3等离子体反应机制,分析回收酸液的NO-2、NO-3离子种类及浓度。考察强电离放电等离子体源的输入功率、水体积百分比、气体温度、气体流速对NOx氧化率的影响。氧化率为97.2%的最佳实验条件是:O+2浓度为1.38×1010个/cm3,O3浓度为210 mg/L,烟气温度为65℃,H2O体积浓度为5.6%,停留时间为0.94 s。     

改性活性炭对水中铬离子(Ⅵ)的吸附性能

为了研究改性前后活性炭对水中铬离子(Ⅵ)的吸附效果,以磷酸活性炭(PAC)为原料,用10%硝酸改性得到硝酸改性活性炭(N-PAC)及直接蒸发法载铁改性得到载铁活性炭(Fe-PAC)。通过静态吸附研究表明,改性后活性炭对Cr(Ⅵ)的吸附率有较大提高。在常温、自然pH条件下,0.2 g活性炭处理50 mL浓度为100 mg/L的含Cr(Ⅵ)溶液,N-PAC和Fe-PAC对Cr(Ⅵ)的吸附率分别为79.21%和90.59%,都高于原PAC对Cr(Ⅵ)的吸附率49.58%。pH从2.2升高到11.92,Fe-PAC对Cr(Ⅵ)的吸附率从99.86%降低到14.77%,N-PAC则从99.86%降低到3.23%,PAC从97.05%降低到2.53%。温度从25℃升高到70℃,3种活性炭对Cr(Ⅵ)吸附率都有较大提高,都增加到98%以上。且吸附过程较符合Langmuir等温吸附模型。     

两级EGSB反应器处理焦化废水的实验研究

采用两级膨胀颗粒污泥床(EGSB)反应器在微氧条件下处理焦化废水,分别考察了一级和二级EGSB反应器(EGSBⅠ和EGSBⅡ)对污染物的去除效果。结果表明,系统能够高效去除COD和NH3-N,EGSBⅠ主要用于去除COD,EGSBⅡ主要用于去除NH3-N。总水力停留时间(HRT)为24 h(EGSBⅠ12 h+EGSBⅡ12 h),系统对952 mg/L的COD、41.3 mg/L的NH3-N、34.55 mg/L的挥发酚、295.8 mg/L的硫氰化物和0.89 mg/L的氰化物的平均去除率分别为78.1%、81.3%、100%、98.1%和89.9%。出水COD、NH3-N、挥发酚、硫氰化物和氰化物的平均浓度分别为208、7.7、0、5.7和0.09 mg/L。出水NH3-N、挥发酚和氰化物浓度均低于《炼焦化学工业污染物排放标准》(GB 16171-2012)的直接排放限值。     

高铝粉煤灰提取氧化铝后硅钙渣用作水泥混合材

为了使高铝粉煤灰提取氧化铝后所产生的硅钙渣被大量的用作水泥混合材,通过水泥强度、水化放热和干缩性实验研究了原状硅钙渣和脱碱硅钙渣对水泥强度和稳定性的影响。结果表明,当硅钙渣掺量达30%时,硅钙渣水泥强度仍可满足P·C 32.5水泥要求。且随硅钙渣掺入量的增加,水泥早期水化放热速率增加的同时水泥累计水化放热量和干缩率还会显著降低。与原状硅钙渣相比,在同等掺量的情况下,脱碱硅钙渣更有利于保持水泥强度,降低其水化热和改善干缩性。     

A comparative study on milk packaging using life cycle assessment: from PA-PE-Al laminate and polyethylene in China

A Life Cycle Assessment (LCA) approach was used to compare the environmental impacts in the life cycle of two milk packaging systems, PA-PE-Al laminate—a laminated foil made from paper, polyethylene and aluminum foil—and polyethylene. The data for the mass, energy fluxes and environmental emissions were obtained from published literature and from site investigations, for the two systems being analyzed for environmental impacts. The application of LCA using Eco-Indicator 99 has made the comparison of the environmental impacts of the two milk packages possible. The results of this LCA study are discussed and the results reveal that the composite packaging has a slightly higher environmental impact than the plastic one. In addition, the environmental impact of raw material extraction is the highest in all of the life cycle stages except for disposal. The environmental impact of composite packaging mainly comes from the fossil fuels, land use and respiratory inorganics categories, while the plastic packaging mainly comes from the fossil fuels category. However, the composite packaging has a greater environmental impact because it has not been well recycled and reused. This environmental impact could be decreased by developing the technology to separate out polyethylene and aluminum from the packaging.     

脂肪酰基氨基酸对矿物润滑油生物降解性的影响研究

通过生物降解试验研究了N-月桂酰基谷氨酸、N-月桂酰基甘氨酸、N-月桂酰基丙氨酸和N-油酰基甘氨酸4种脂肪酰基氨基酸对HVI 350矿物润滑油生物降解性的影响，采用高倍电子显微镜分析了生物降解过程中微生物数量和形态变化。结果表明，在矿物润滑油中添加少量脂肪酰基氨基酸后，矿物润滑油的生物降解性能明显改善，且生物降解过程中微生物数量增多、形态发生变化，这可能是脂肪酰基氨基酸增加了微生物的营养，且具有表面活性，有利于细胞的吸收，从而促进了矿物润滑油生物降解。     

Online detection of waterborne bioavailable copper by valve daily rhythms in freshwater clam Corbicula fluminea

Freshwater clam Corbicula fluminea, a surrogate species in metal toxicity testing, is a promising bioindicator of impairment in aquatic ecosystems. Little is known, however, about the relationship between clam valve daily rhythmic response and metal bioavailability related to a metal biological early warning system (BEWS) design. The purpose of this study was to link biotic ligand model (BLM)-based bioavailability and valve daily rhythm in C. fluminea to design a biomonitoring system for online in situ detection of waterborne copper (Cu). We integrated the Hill-based dose-time-response function and the fitted daily rhythm function of valve closure into a constructed programmatic mechanism. The functional presentation of the present dynamic system was completely demonstrated by employing a LabVIEW graphic control program in a personal computer. We used site-specific effect concentration causing 10% of total valve closure response (EC10) as the detection threshold to implement the proposed C. fluminea-based Cu BEWS. Here our results show that the proposed C. fluminea-based BEWS could be deliberately synthesized to online in situ transmit rapidly the information on waterborne bioavailable Cu levels under various aquatic environmental conditions through monitoring the valve daily rhythmic changes. We suggested that the developed C. fluminea-based dynamic biomonitoring system could assist in developing technically defensible site-specific water quality criteria to promote more efficient uses in water resources for protection of species health in aquatic environments.     

Polymers as Solid Waste in Municipal Landfills

Abstract

Synthetic polymers reach municipal landfills as components of products such as waste household paints, packaging films, storage containers, carpet fibers, and absorbent sanitary products. Some polymers in consumer products that reach landfills are designed to photodegrade or biodegrade. This article examines the significance of degradable polymers in management of solid waste in municipal landfills. Most landfills are not designed to photodegrade or biodegrade solid waste. Landfill disposal of stable polymers such as polyacrylics and polyethylenes is not associated with significant polymer degradation or mobility. Stability to photodegradation and biodegradation is an advantage when municipal landfills are used for disposal of polymer products as solid waste. Use of landfill disposal can be a responsible means to manage polymer waste and can be part of an overall waste management plan which includes source reduction, recycling, reuse, composting, and waste-to-energy incineration.     

Filter Beds: Energy-Efficient Packing Diameter

Factors which help minimize pressure drop at a given level of collection efficiency for a bed packed with roughly spherical collectors are studied here by using the quality factor, the ratio of the single collector collection efficiency to the force per unit area on the single collector. This analysis indicates that energy-efficient designs can be obtained as follows: choose a representative particle size; if impaction predominates, design for an impaction parameter near one; if interception predominates, design for the smallest packing diameters feasible; if gravitational settling predominates, design for the largest packing diameters possible; if diffusion predominates, design for collector Reynolds numbers near 10². Some more general cases are also discussed.     

Dry Deposition Velocity as an Indicator for SO2 Damage to Materials

Data from the literature on dry deposition of SO₂ to various common materials in outdoor atmospheres are reviewed and presented in the context of a theoretical model. The model postulates two resistances to deposition: the aerodynamic resistance, controlled by atmospheric properties; and the surface resistance, controlled by the chemistry of the surface and its moisture layer. Since the dissolution of SO₂ is sensitive to pH, buffering of the moisture layer by corrosion products is essential for SO₂ deposition to continue. Thus, it is hypothesized that SO₂ deposits preferentially on those surfaces that are sensitive to SO₂ attack. Based on extant data, estimates of aerodynamic and surface resistances are derived from the literature and maximum "dry" deposition rates for SO₂ are estimated. Such information could be used to formulate SO₂ dose-response or "damage" functions for certain materials, based on short-term laboratory tests.