洪水灾害评估体系研究

从系统论的观点出发，提出了洪水灾害系统的概念，并结合洪水灾害评估的特点，设计了洪水灾害评估体系的总体框架。     

玉米芯为碳源实现酸性矿山废水生物处理

引入了一种新的碳源——玉米芯，对SRB法处理酸性矿山废水进行了更加深入的探索，分析了各种参数条件对s暖一还原效果的影响，确定了常温下这种碳源所需要的最适宜工况条件，探讨了硫酸盐矿山废水的水质资源化问题，并对山西矿山废水的生物治理进行了可行性实验验证。实验证明，玉米芯为碳源时，矿山废水中SO^2-4的出水值可达221．1mg／L，金属离子的浓度也都达到了生活饮用水的质量标准，所以玉米芯可作为酸性矿山废水资源化生物处理的合适有效碳源。     

水解-接触氧化工艺处理针织染整废水

介绍了采用水解-接触氧化工艺处理针织染整废水,工程运行结果表明：CODcr和色度的去除率分别达到91.3%、88%,最终排放污水达到国家污水Ⅰ级标准.该工艺具有处理效果好、经济、运行稳定等特点,在染整废水处理中具有实用性.     

Sustainability of Current Agricultural Practices in The Cameron Highlands, Malaysia

Cameron Highlands is a mountainous region with steep slopes. Gradients exceeding 20^∘ are common. The climate is favourable to the cultivation of tea, sub-tropical vegetables and flowers (under rain-shelter). Crop production is sustained by high fertiliser and manure applications. However, agriculture in this environment is characterised by high levels of soil erosion and environmental pollution. A study on the sustainability of these agro-ecosystems was conducted. Results indicated that soil loss was in the range of 24–42 ton/ha/yr under vegetables and 1.3 ton under rain-shelter. Sediment load in the vegetable sub-catchment reached 3.5 g/L, 50 times higher than that associated with flowers under rain-shelter and tea. The sediments contained high nutrient loads of up to 470 kg N/ha/yr. The N, P and K lost in runoff from cabbage farms was 154 kg/season/ha, whereas in chrysanthemum farms it was 5 kg. In cabbage farms, the N, P, and K lost through leaching was 193 kg/season/ha. The NO₃–N concentration in the runoff from the cabbage farms reached 25 ppm but less than 10 ppm in runoff from rain-shelters. Inorganic pollution in the rivers was within the acceptable limit of 10 ppm. The sustainability of the agro-ecosystems is in the order of tea { > } rain–shelter ≫ vegetables.     

Residues of endosulfan and other selected organochlorine pesticides in farm areas of the Lower Fraser Valley, British Columbia, Canada

Crop soils, ditch sediments, and water flowing from several farm areas to salmon tributary streams of the Fraser River in the Lower Fraser Valley (LFV) of British Columbia, Canada, were sampled in 2002-2003 to quantify for residues of an organochlorine cyclodiene pesticide, endosulfan (END = alpha-endosulfan + beta-endosulfan + endosulfan sulfate). Residues from historical use of other selected organochlorine pesticides, namely, cyclodienes (aldrin, alpha-chlordane, gamma-chlordane, dieldrin, endrin, endrin aldehyde, heptachlor, and heptachlor epoxide), hexachlorocyclohexanes [alpha-benzene-hexachloride (alpha-BHC), beta-BHC, delta-BHC, and gamma-BHC (lindane)], and DDT-related compounds (p,p-DDT, p,p-DDD, p,p-DDE, and methoxychlor) were also determined. Reference and background levels of these pesticides in ditches leading to fish streams were obtained from pristine watershed areas. Varying amounts of END residues were detected in soils (<0.02-5.60 mg kg(-1) dry wt.) and ditch sediments (<0.02-3.33 mg kg(-1) dry wt.) in mainly three of five farm areas sampled. Likewise, residues (excluding END) of other selected organochlorine compounds such as aldrin, BHC, chlordane, endrin, p,p-DDT, methoxychlor, and their respective major transformation products (endosulfan sulfate, dieldrin, endrin aldehyde, heptachlor, heptachlor epoxide, p,p-DDD, and p,p-DDE) were found in crop soils (<0.02-16.2 mg kg(-1) dry wt.) and sediments (<0.02-9.73 mg kg(-1) dry wt.). Most of these pesticides (END: <0.01-1.86 microg L(-1); other selected organochlorine pesticides: <0.0.1-1.50 microg L(-1)) were also found in ditch water leading to salmon streams in several farms. The END levels of crop soils from the same LFV study farms in 1994 and 2003 indicated an estimated decline of 22% to 1.35 mg kg(-1) dry wt. during that period. This reduction was probably due to the increasing use of alternate pesticides (e.g., organophosphorus compounds). Some possible biological implications of these pesticide residues on nontarget organisms in the LFV are discussed.     

Distribution,sources, and ecological risk assessment of SVOCs in surface sediments from Guan River Estuary,China

The contamination of semi-volatile organic compounds (SVOCs) in the surface sediments of the Guan River Estuary, China was fully investigated. Total concentrations of 56 species of SVOCs ranged from 132 to 274 ng/g with an average of 186 ng/g (dry weight). Polycyclic aromatic hydrocarbon (PAH) concentrations were positively correlated with clay content and negatively correlated with sediment grain size. Source identification indicated that PAHs originated mainly from pyrolytic sources. However, intense ship traffic in the estuary may provide sources of petrogenic PAHs. Organochlorine pesticides (OCPs) mainly originated from direct input of dichlorodiphenyltrichloroethanes (DDTs) during some industrial processes. The SVOC concentrations were also compared with International Sediments Quality Guidelines and Sediments Quality Criteria, and the results indicated that negative biological impacts may originate from high concentrations of FLO, p,p′-DDE, and total DDTs.     

Effects of fly ash addition on physical properties of porous clay-fly ash composites via polymeric replica technique

The porous composites of clay and fly ash have the potential to be used in many fields, such as catalyst support and gas adsorbents. In this study, various ratios of fly ash (1–2) with different percentage of suspension (50–70 wt%) were applied to produce porous clay-fly ash composites via polymeric replica technique. Fabrication process starts by mixing clay and fly ash in distilled water to form slurry. The process is followed by fully immersing polymer sponge in slurry. The excess slurry is then removed through squeezing. Finally, the sponge coated with slurry is sintered at 500 and 1250 °C for 1 h. It is found that the compressive strength of porous composites improves significantly (0.178–1.28 MPa) when the amount of clay-fly ash suspension mixture (50–70 wt%) increases. The compressive strength of porous composites is mainly attributed to the mullite, quartz and amorphous phase formations. These results are supported by X-ray diffraction analysis. On the other hand, increase in the amount of suspension reduces the apparent density (from 2.44 to 2.32 g/cm³) and porosity (from 97 to 85 %). The reduction in apparent density is believed to be caused by the presence of high fly ash content in porous composites. The melted fly ash cenospheres have closed the internal pores and increased density of samples. Higher suspension level not only reduces porosity, but also increases close pores of the porous composites. The results are justified through the observation from the structures of porous clay-fly ash composites.     

Catalytic activities and mechanism of formaldehyde oxidation over gold supported on MnO<Subscript>2</Subscript> microsphere catalysts at room temperature

MnO₂ microspheres with various surface structures were prepared using the hydrothermal method, and Au/MnO₂ catalysts were synthesized using the sol-gel method. We obtained three MnO₂ microspheres and Au/MnO₂ samples: coherent solid spheres covered with wire-like nanostructures, solid spheres with nanosheets, and hierarchical hollow microspheres with nanoplatelets and nanorods. We investigated the properties and catalytic activities of formaldehyde oxidation at room temperature. Crystalline structures of MnO₂ are the main factor affecting the catalytic activities of these samples, and γ-MnO₂ shows high catalytic performance. The excellent redox properties are responsible for the catalytic ability of γ-MnO₂. The gold-supported interaction can change the redox properties of catalysts and accelerate surface oxygen species transition, which can account for the catalytic activity enhancement of Au/MnO₂. We also studied intermediate species. The dioxymethylene (DOM) and formate species formed on the catalyst surface were considered intermediates, and were ultimately transformed into hydrocarbonate and carbonate and then decomposed into CO₂. A proposed mechanism of formaldehyde oxidation over Au/MnO₂ catalysts was also obtained.     

An investigation on pollutant emissions from co-firing of RDF and coal

Pollutant emissions from co-firing of refuse derived fuel (RDF) and coal were investigated in a vortexing fluidized bed combustor (VFBC). RDF-5 was made of common municipal solid waste (MSW). CaCO₃ was injected in the combustor to absorb HCl at 850 °C. The results show that NO_x and HCl emissions increase with RDF-5 co-firing ratio. The NO_x concentration in flue gas at the bottom of the combustor is higher than that at the top. However, the trend of HCl released is reverse compared with NO_x emissions. It was found that the HCl concentration decreases with increasing the molar ratio of Ca/Cl. However, the effect of CaCO₃ addition on HCl retention is not significant when the molar ratio of Ca/Cl is higher than 5. The chlorine content in fly ash increases obviously with the molar ratio of Ca/Cl. PCDD/Fs emissions decrease slightly with an addition of CaCO₃. In this study incomplete combustion is regarded as the main cause for polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) formation.     

Factors affecting the implementation of green specifications in construction

Green specifications constitute one of the important elements in green construction. New sustainability requirements and changing priorities in construction management have spurred the emerging green specifications to a faster pace of development. A cross-sectional survey has been conducted in Hong Kong in 2007 to identify principal factors leading to the success of preparing green specifications. Based on extensive construction management literature, 20 variables concerning sustainable construction were summarized. Using the Mann–Whitney U-test, the subtle differences between stakeholders in specifying construction work have been detected even with the high consistency of the responses among the groups. Moreover, five independent factors for successful specification of green construction have been categorized by factor analysis. They are related to (1) green technology and techniques, (2) reliability and quality of specification, (3) leadership and responsibility, (4) stakeholder involvement, and (5) guide and benchmarking systems. Whilst the first and fourth factors are generally more important, different stakeholder groups have different emphases. The results of the survey have been validated against established principles.