锐钛矿型二氧化钛的低温合成及其吸附除氟性能的研究

通过水解法在50℃低温条件下合成了锐钛矿型TiO₂,使用XRD、FT-IR、BET等方法对TiO₂进行了表征,并研究其对水中氟离子的吸附行为。结果表明:所合成锐钛矿型TiO₂比表面积达到278.93 m2/g,常温下对氟离子的最大吸附量为30.02 mg/g。吸附过程符合Langmuir等温线模型和准一级动力学模型,是自发性的吸热过程,吸附机理为静电吸引。     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

精神活性物质在北京市某污水处理厂中的污染特征与生态风险

为了解污水处理厂对精神活性物质的去除特征及总出水对受纳水体的生态风险,采用固相萃取-高效液相色谱-串联质谱法调查了北京市某污水处理厂中13种精神活性物质的浓度水平与负荷量变化,并运用RQ（risk quotient,风险熵）对总出水中精神活性物质进行风险评估.结果表明:①13种精神活性物质在总进水与总出水中均能检出,总质量浓度平均值分别为2 395.10和63.59 ng/L,其中ρ（EPH）（EPH表示麻黄碱）占比分别为93.9%和67.9%,其次为COD（可待因）与METH（甲基苯丙胺）.污水处理厂上游地表水中ρ（EPH）、ρ（METH）与ρ（KET）（KET为氯胺酮）均高于总出水及其下游地表水,说明上游沿河可能有新的污染源输入.②污水处理厂对NK（去甲氯胺酮）、BE（苯甲酰爱康宁）和MTD（美沙酮）均呈负去除,其他精神活性物质的去除主要发生在二级生物处理与三级处理（超滤膜与UV消毒）阶段.③污水处理厂服务区域内精神活性物质的周内负荷量存在一定波动,AMP（苯丙胺）、METH、MDA（3,4-亚甲二氧基苯丙胺）、MDMA（3,4-亚甲二氧基甲基苯丙胺）、KET与HER（海洛因）的负荷量均在周末升高.④污水处理厂总出水中精神活性物质的生态风险均较低（RQ < 0.10）.研究显示,污水处理厂不能完全去除污水中的精神活性物质,总出水中残留精神活性物质对受纳河流生态系统产生的长期混合效应不容忽视.      

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

基于TMVOC的地下水位波动带苯系物迁移转化模拟

为探究水位波动情况下苯系物的迁移转化规律,提高石油污染场地地下水污染治理精度,以西北某傍河石化场地为研究对象,基于TMVOC模型对特征污染物苯系物开展泄漏模拟,通过情景模拟比较水位波动对苯系物迁移转化的影响,并从污染分布、相间转化等方面,解析地下水位稳定和波动状态下苯系物迁移转化过程差异.结果表明:①TMVOC模型较好地模拟了水位波动状态下苯系物迁移转化过程.②相较于水位稳定状态下,水位波动作用下苯系物污染深度增加0.5 m,污染面积增加25%,总质量增加12 kg.③水位稳定和波动状态下苯系物"气-液-NAPL（Non-Aqueous Phase Liquids）相"占比分别为0.17%、2.03%、97.8%和0.04%、3.69%、96.27%.④NAPL相苯系物饱和度分布与苯系物质量分布呈正相关,水位波动造成NAPL相初始饱和度降低,且初始水位面以下NAPL相饱和度升高.⑤对于苯而言,水位波动状态下非饱和带中苯在液相中的质量是水位稳定状态下的1.11倍,饱和带为10.15倍.研究显示,水位波动显著地影响了苯系物的迁移转化过程,促进了苯系物的溶解,并使更多的苯系物残留在地下介质中.      

深圳市龙岗区大气颗粒物中多溴联苯醚的污染特征研究

为了解深圳市龙岗区大气颗粒物中多溴联苯醚的污染状况,于2017年1月、4月、8月和11月分别采集龙岗区大气颗粒物样品.利用气相色谱-质谱联用仪（GC/MS）对深圳市龙岗区4个功能区（工业区、商业区、居民区和生态区）的80个大气颗粒物样品进行检测,得到PBDEs（多溴联苯醚）8种单体（BDE-28、BDE-47、BDE-99、BDE-100、BDE-153、BDE-154、BDE-183、BDE-209）的质量浓度,同时研究了大气颗粒物中PBDEs质量浓度的时空分布特征.结果表明:①深圳市龙岗区大气颗粒物中ρ（∑₈PBDEs）（∑₈PBDEs为PBDEs 8种单体的加和）范围为0.07~77.80 pg/m3,ρ（∑₈PBDEs）年均值为（6.86±14.17）pg/m3.ρ（BDE-209）范围为0.01~76.23 pg/m3,年均值为（5.10±13.58）pg/m3,BDE-209为主要污染单体.② 4个功能区的ρ（∑₈PBDEs）平均值大小顺序依次为工业区（13.65 pg/m3）>商业区（7.75 pg/m3）>生态区（3.95 pg/m3）>居民区（2.19 pg/m3）,工业区是环境空气颗粒物中PBDEs的主要污染区.③ ρ（∑₈PBDEs）平均值的季节性变化规律为春季（13.32 pg/m3）>冬季（9.18 pg/m3）>秋季（2.17 pg/m3）>夏季（1.51 pg/m3）,符合深圳市亚热带海洋季风气温和气候对环境空气中颗粒物质量浓度的影响规律.研究显示,深圳市龙岗区大气颗粒物中PBDEs质量浓度处于较高水平,污染严重,建议减少含PBDEs产品的生产、使用和运输等活动,或找到更利于环境安全和人体健康的替代品,降低PBDEs对该地区的污染.      

不同制备温度下污泥生物炭对Cr(Ⅵ)的吸附特性

以城市剩余污泥为原料,于300,400,500,600 ℃温度条件下制备生物炭,通过单因素静态吸附实验探讨制备温度对生物炭吸附Cr（Ⅵ）的影响。结果表明:在500 ℃以内随着温度上升制备的生物炭对Cr（Ⅵ）的吸附量增加,制备温度高于500 ℃后变化不明显;扫描电镜（SEM）、比表面积（BET）、傅里叶红外光谱（FTIR）表征结果显示,热解温度对生物炭表面形貌和官能团组成有显著影响;等温模型及动力学拟合结果表明,生物炭吸附Cr（Ⅵ）为单分子层吸附、物理-化学复合吸附。热解温度对污泥制备生物炭吸附Cr（Ⅵ）的性能有显著影响,最佳制备温度为500 ℃,在此条件制备的生物炭对Cr（Ⅵ）的理论吸附量可达7.93 mg/g。     

污水处理过程专家系统的结构特点与应用研究进展

综述了专家系统在污水处理领域的结构和特点、针对的工艺以及应用现状方面取得的研究成果。重点介绍了专家系统中知识的获取和表示、规则的建立以及与故障树和其他人工智能技术的结合情况,并对专家系统在污水处理工艺选择、运行控制以及故障诊断3个阶段的研究现状进行了细致分析。在此基础上,提出了尚需解决的问题以及进一步研究与发展的方向。     

Concentrations and chemical compositions of PM10 during hazy and non-hazy days in Beijing

In order to study the concentrations of major components,characteristics and comparison in hazy and non-hazy days of PM_(10) in Beijing,aerosol samples were collected at urban site in Beijing from December 29,2014 to January 22,2015.Heavy metals like Zn,Pb,Mn,Cu,As,V,Cr and Cd were deeply studied considering their toxic effects on human being;nine water-soluble inorganic ions(SO_4~(2-),NO_3~-,NH_4~+,Na~+,K~+,Cl~-,Ca~(2+) and Mg~(2+)) and carbon fractions(OC and EC) were also analyzed.The concentrations of heavy metals were 1.03–1.98 times higher in hazy days than those in non-hazy days,mainly due to biomass burning and coal burning.The trends in total heavy metals concentrations were basically consistent with the trends in PM concentrations except for two obvious periods(12.29–12.30;1.14–1.15);but when air masses accumulated locally or around Beijing,trends in PM concentrations and heavy metals were opposite.The proportion for NO_3~-/SO_4~(2-) indicated that mobile sources such as automobiles were important reasons for haze in Beijing.Correlation between OC and EC during non-hazy days was strong(R~2= 0.95) but it was low(R~2= 0.67) during hazy days,and large variations for OC/EC values occurred in hazy days.The calculated mass concentration of SOC is 2.58 μg/m~3,which only accounted for 10.1% of the OC concentration.When air masses from the far north-west,they decreased PM concentration in Beijing and they were relatively clean;however,those from the near east,south-east and south of the mainland increased PM concentration and they were dirty.     

过硫酸钠缓释材料的释放性能及其对2, 4-二硝基甲苯的降解效果

针对原位化学氧化技术修复土壤和地下水时氧化剂因释放过快而导致的利用率低等问题,通过熔化成型法制备过硫酸钠缓释材料,分析石蜡、硅砂和过硫酸钠不同配比对材料成型度和释放性能的影响,研究缓释过程中溶液pH的变化,探讨其在水溶液中的缓释行为及其对2,4-二硝基甲苯（2,4-DNT）的降解效果.结果表明:当固定过硫酸钠质量为6 g、硅砂质量为18 g、蜡砂比（石蜡、硅砂质量之比）为1:4~1:8时,过硫酸钠缓释材料成型度适中,且过硫酸钠的累积缓释量随着时间的延长而逐渐增大,第31天时过硫酸钠累积释放百分比为74.67%~88.40%,可实现过硫酸钠的持续可控释放.当硅砂质量为18 g、蜡砂比为1:1~1:6时,过硫酸钠累积释放百分比随着过硫酸钠质量的增加而增大,且溶液中的pH呈先降低后上升的变化规律.缓释材料缓释前后实物图和显微镜分析结果显示,过硫酸钠缓释材料的释放是一个由外到内、速率由快变慢最终趋于平稳的过程.过硫酸钠质量为12 g、硅砂质量为18 g、蜡砂比为1:4的缓释材料对2,4-DNT具有较好的降解效果,第16次置换浓度为0.2 mg/L的2,4-DNT水溶液时,2,4-DNT的降解率为56.38%.研究显示,改变制备材料的配比可有效实现缓释材料中过硫酸钠的缓慢释放及对污染物的有效降解,可为原位化学氧化修复土壤和地下水提供理论支撑.