Occurrence of alternative flame retardants in indoor dust from New Zealand: indoor sources and human exposure assessment

Due to worldwide restrictions on polybrominated diphenyl ethers (PBDEs), the demand for alternative flame retardants (AFRs), such as organophosphate flame retardants (OPFRs), novel brominated FRs (NBFRs) and hexabromocyclododecanes (HBCDs), has recently increased. Little is known about human exposure to NBFRs and OPFRs and that their levels in dust have been scarcely evaluated worldwide. To increase the knowledge regarding these chemicals, we measured concentrations of five major NBFRs, ten OPFRs and three HBCD isomers in indoor dust from New Zealand homes. Dust samples were taken from living room floors (n=34) and from mattresses of the same houses (n=16). Concentrations (ngg(-1)) of NBFRs were: 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE) (<2-175), decabromodiphenyl ethane (DBDPE) (<5-1430), 2-ethylhexyl-2,3,4,5-tetrabromobenzoate (TBB) (<2-2285) and bis(2-ethylhexyl)-3,4,5,6-tetrabromophthalate (TBPH) (<2-640). For OPFRs, concentrations (ngg(-1)) ranged between: tri-ethyl-phosphate (TEP) (<10-235), tri-n-butyl-phosphate (TnBP) (<20-7545), tris-(2-chloroethyl)-phosphate (TCEP) (<20-7605), tris-(1-chloro-2-propyl) phosphate (TCPP) (20-7615), tri-(2-butoxyethyl)-phosphate (TBEP) (50-27325), tris-(2,3-dichloropropyl)-phosphate (TDCPP) (20-16560), tri-phenyl-phosphate (TPhP) (20-35190), and tri-cresyl-phosphate (TCP) (<50-3760). HBCD concentrations fell in the range <2-4100ngg(-1). BTBPE, DBDPE, TBPH, TBEP, and TnBP showed significant positive correlation (p<0.05) between their concentrations in mattresses and the corresponding floor dust (n=16). These data were used to derive a range of plausible exposure scenarios. Although the estimated exposure is well below the corresponding reference doses (RfDs), caution is needed given the likely future increase in use of these FRs and the currently unknown contribution to human exposure by other pathways such as inhalation and diet.     

Minimization of the formation of disinfection by-products

The drinking water industry is required to minimize DBPs levels while ensuring adequate disinfection. In this study, efficient and appropriate treatment scheme for the reduction of disinfection by-product (DBPs) formation in drinking water containing natural organic matter has been established. This was carried out by the investigation of different treatment schemes consisting of enhanced coagulation, sedimentation, disinfection by using chlorine dioxide/ozone, filtration by sand filter, or granular activated carbon (GAC). Bench scale treatment schemes were applied on actual samples from different selected sites to identify the best conditions for the treatment of water. Samples were collected from effluent of each step in the treatment train in order to analyze pH, UV absorbance at 254 nm (UVA₂₅₄), specific UV absorbance at 254 nm (SUVA₂₅₄), dissolved organic carbon (DOC), haloacetic acids (HAAs) and trihalomethanes (THMs). The obtained results indicated that using pre-ozonation/enhanced coagulation/activated carbon filtration treatment train appears to be the most effective method for reducing DBPs precursors in drinking water treatment.     

Incorporating organizational factors into probabilistic risk assessment of complex socio-technical systems: Principles and theoretical foundations

The current generation of Probabilistic Risk Analysis (PRA), particularly those for technical systems, does not include an explicit representation of the possible impacts of organization and management on the safety performance of equipment and personnel. There are a number of technical challenges in developing a predictive model of organizational safety performance. There is a need for a widely accepted and theoretically sound set of principles on which models of organizational influences could be developed and validated. As a result of a multidisciplinary effort, this paper explores the feasibility of developing such principles and proposes a set of principles for organizational safety risk analysis. Then, as a realization of the proposed modeling principles, a safety risk framework, named Socio-Technical Risk Analysis (SoTeRiA), is developed. SoTeRiA formally integrates the technical system risk models with the social (safety culture and safety climate) and structural (safety practices) aspects of safety prediction models, and provides a theoretical basis for the integration. A systematic view of safety culture and safety climate leaves an important gap in modeling complex system safety risk, and SoTeRiA, describing the relationship between these two concepts, bridges this gap. The framework explicitly recognizes the relationship among constructs at multiple levels of analysis, and extends the PRA framework to include the effects of organizational factors in a more comprehensive and defensible way.     

Removal of dinitrotoluenes from water via reduction with iron and peroxidase-catalyzed oxidative polymerization: a comparison between Arthromyces ramosus peroxidase and soybean peroxidase

A two-step process for the removal of dinitrotoluene from water is presented: zero-valent iron reduction is coupled with peroxidase-catalyzed polymerization of the resulting diaminotoluenes (DAT). The effect of pH was examined in the reduction step: at pH 6 the reaction occurred much more rapidly than at pH 8. In the second step, optimal pH and substrate ratio, minimal enzyme concentration and effect of polyethylene glycol (PEG) as an additive for greater than 95% conversion of DAT, over a 3h reaction period were determined using high performance liquid chromatography. Two enzymes were investigated and compared: Arthromyces ramosus peroxidase (ARP) and soybean peroxidase (SBP). The optimal pH values were 5.4 and 5.2 for ARP and SBP, respectively, but SBP was more resistant to mild acid whereas ARP was more stable in neutral solutions. SBP was found to have a greater hydrogen peroxide demand (optimal peroxide/DAT molar ratio for SBP: 2.0 and 3.0 for 2,4-diaminotoluene (2,4-DAT) and 2,6-diaminotoluene (2,6-DAT), respectively; for ARP: 1.5 and 2.75 for 2,4-DAT and 2,6-DAT, respectively) but required significantly less enzyme (0.01 and 0.1 U ml(-1) for 2,4-DAT and 2,6-DAT, respectively) to convert the DAT than ARP (0.4 and 1.5 U ml(-1) for 2,4-DAT and 2,6-DAT, respectively). PEG was shown to have no effect upon the degree of substrate conversion for either enzyme.     

Heavy metal contamination from mining sites in South Morocco: Monitoring metal content and toxicity of soil runoff and groundwater

The aim of the present work is the assessment of metal toxicity in runoff, in their contaminated soils and in the groundwater sampled from two mining areas in the region of Marrakech using a microbial bioassay MetPLATE™. This bioassay is based on the specific inhibition of the β-galactosidase enzyme of a mutant strain of Escherichia coli, by the metallic pollutants. The stream waters from all sampling stations in the two mines were all very toxic and displayed percent enzyme inhibition exceeding 87% except SWA₄ and SWB₁ stations in mine C. Their high concentrations of copper (Cu) and zinc (Zn) confirm the acute toxicity shown by MetPLATE. The pH of stream waters from mine B and C varied between 2.1 and 6.2 and was probably responsible for metal mobilization, suggesting a problem of acid mine drainage in these mining areas. The bioassay MetPLATE™ was also applied to mine tailings and to soils contaminated by the acidic waters. The results show that the high toxicity of these soils and tailings was mainly due to the relatively concentration of soluble Zn and Cu. The use of MetPLATE™ in groundwater toxicity testing shows that, most of the samples exhibited low metal toxicity (2.7–45.5% inhibition) except GW3 of the mine B (95.3% inhibition during the wet season and 82.9% inhibition during the dry season). This high toxicity is attributed to the higher than usual concentrations of Cu (189 μg Cu l⁻¹) and Zn (1505 μg Zn l⁻¹). These results show the potential risk of the contamination of different ecosystems situated to the vicinity of these two metalliferous sites. The general trend observed was an increase in metal toxicity measured by the MetPLATE with increasing total and mobile metal concentrations in the studied matrices. Therefore, the MetPLATE bioassay is a reliable and fast bioassay to estimate the metals toxicity in the aquatic and solids samples.     

Water Quality Changes in Chini Lake, Pahang, West Malaysia

A study of the water quality changes of Chini Lake was conducted for 12 months, which began in May 2004 and ended in April 2005. Fifteen sampling stations were selected representing the open water body in the lake. A total of 14 water quality parameters were measured and Malaysian Department of Environment Water Quality Index (DOE-WQI) was calculated and classified according to the Interim National Water Quality Standard, Malaysia (INWQS). The physical and chemical variables were temperature, dissolved oxygen (DO), conductivity, pH, total dissolved solid (TDS), turbidity, chlorophyll-a, biochemical oxygen demand (BOD), chemical oxygen demand (COD), total suspended solid (TSS), ammonia-N, nitrate, phosphate and sulphate. Results show that base on Malaysian WQI, the water in Chini Lake is classified as class II, which is suitable for recreational activities and allows body contact. With respect to the Interim National Water Quality Standard (INWQS), temperature was within the normal range, conductivity, TSS, nitrate, sulphate and TDS are categorized under class I. Parameters for DO, pH, turbidity, BOD, COD and ammonia-N are categorized under class II. Comparison with eutrophic status indicates that chlorophyll-a concentration in the lake was in mesotrophic condition. In general water quality in Chini Lake varied temporally and spatially, and the most affected water quality parameters were TSS, turbidity, chlorophyll-a, sulphate, DO, ammonia-N, pH and conductivity.     

Genotoxicity assessment of acute exposure of chlorpyrifos to freshwater fish Channa punctatus (Bloch) using micronucleus assay and alkaline single-cell gel electrophoresis

Chlorpyrifos (O,O-diethyl O-3,5,6-trichloro-2-pyridylphosphorothioate) is one of the organophosphate pesticides widely used in agricultural practices throughout world and irreversible inhibitor of cholinesterase in all animal species. Limited efforts have been made to study acute genotoxic effects of chlorpyrifos (CPF) in different tissues of fish using genotoxic biomarkers. Therefore, the present investigation was aimed to study the induction of DNA damage by CPF in freshwater teleost fish Channapunctatus using micronucleus assay (MN assay) and alkaline single-cell gel electrophoresis (comet assay). The value of LC(50) - 96 h of CPF was determined as 811.98 microgl(-1) for C. punctatus, in a semi-static system and on the basis of LC(50) value three acute concentrations viz., 203, 406 and 609 microgl(-1) were determined. The fishes were exposed to the different concentrations of CPF for 96 h and samplings were done at regular intervals for assessment of the MN frequencies and DNA damage. In general, significant effects (P<0.01) from both concentrations and time of exposure were observed in exposed fishes. It was found that the micronucleus induction was highest on 96 h at all concentrations in the peripheral blood. Similar trend was observed for the DNA damage measured in terms of the percentage of tail DNA in the lymphocyte and gill cells. This study explored the combined use of micronucleus assay and comet assay for in vivo laboratory studies using fresh water fish for screening the genotoxic potential of xenobiotics.     

28-homobrassinolide protects chickpea (Cicer arietinum) from cadmium toxicity by stimulating antioxidants

In the present experiment the seeds of Cicer arietinum (L.) cv. Uday were inoculated with specific Rhizobium grown in sandy loam soil and were allowed to grow for 15 days. At this stage, the seedlings were supplied with 0, 50, 100 or 150 microM of cadmium in the form of cadmium chloride and sprayed with 0.01 microM of 28-homobrassinolide (HBL) at 30-day stage. The data indicated that plant fresh and dry mass, number of nodules, their fresh and dry mass, leghemoglobin content, nitrogen and carbohydrate content in the nodules, leaf chlorophyll content, nitrate reductase and carbonic anhydrase activities decreased proportionately with the increasing concentrations of cadmium but the content of proline and the activities of catalase, peroxidase and superoxide dismutase increased. The ill effect, generated by cadmium, was overcome if the stressed plants were sprayed with HBL.     

A mathematical model to predict the composition and generation of hospital wastes in Iran

The aim of this study is to investigate the quality and quantity of hospital wastes in Iran. The generated hospital wastes have been estimated by the number of hospitals and the number of active beds in each province of Iran in 2001. All data and information have been gathered from: (i) Iran Statistics Center, (ii) literature review, and (iii) hospital waste investigations for an average hospital. Physical analyses have been conducted in terms of various materials (plastic, textile, paper, metal, and others) and components (biological, infectious, medical, and regular wastes). Based on the above-mentioned investigation and information, a mathematical model has been developed to calculate the generation of (infectious) hospital wastes for any desired year. Utilizing the model, generated infectious hospital wastes has been estimated as 698,937 tones for 2008 (short-term) and 3,494,387 tones for 2028 (long-term period). If the real infectious wastes are collected separately, then the generated infectious wastes will be reduced by 15.1% of the above-mentioned amount (139,787 tones for 2008, and 698,877 tones for 2028). Results of physical analysis show the components of the hospital waste as: (a) infectious, 67.3%; (b) medical, 8.8%; (c) biological, 1.8%; and (d) common municipal wastes, 22.1%. An appropriate collection method requires training the staff at hospitals along with preparation of the required facilities. Of course, both of these requirements are cost intensive.     

The CO2 abatement cost curve for the Thailand cement industry

The cement industry is one of the largest carbon dioxide (CO₂) emitters in the Thai industry. The cement sector accounted for about 20,633 kilotonnes (ktonnes) CO₂ emissions in 2005 in Thailand. A bottom-up CO₂ abatement cost curve (ACC) is constructed in this study for the Thai cement industry to determine the potentials and costs of CO₂ abatement, taking into account the costs and CO₂ abatement of different technologies. The period of 2010–2025 is chosen as the scenario period. We analyzed 41 CO₂ abatement technologies and measures for the cement industry. Using the bottom-up CO₂ ACC model, the cost-effective annual CO₂ abatement potential for the Thai cement industry during the 15 year scenario period (2010–2025) is equal to 3095 ktonnes CO₂/year. This is about 15% of the Thai cement industry’s total CO₂ emissions in 2005. The total technical annual CO₂ abatement potential is 3143 ktonnes CO₂/year, which is about 15.2% of the Thai cement industry’s total CO₂ emissions in 2005. We also conducted a sensitivity analysis for the discount rate parameter.