黄孢原毛平革菌处理染料废水过程中细胞结构损伤效应研究

利用透射电子显微镜观察分析白腐真菌(黄孢原毛平革菌)在处理染料废水活性艳红X-3B过程中,染料和盐度对黄孢原毛平革菌的细胞结构产生的毒性作用.结果表明:活性艳红X-3B染料对黄孢原毛平革菌产生生物毒性作用,且随着染料浓度的增加,细胞受损伤程度不断加深.加入100 mg/L的染料活性艳红X-3B后,黄孢原毛平革菌菌丝细胞形态发生变化,出现质壁分离现象;染料浓度进一步加大,菌丝细胞超微结构受到损伤逐渐严重.染料废水中的盐度对黄孢原毛平革菌细胞也会造成损伤,且损伤程度随盐度增大而增大.NaCl浓度为3 g/L时,菌丝细胞发生质壁分离;而当NaCl加入量高于8 g/L时,细胞膜受损,线粒体、细胞核呈现空泡化,表现为受到不可逆的损伤.染料和盐双因子对黄孢原毛平革菌细胞的损伤效应表现为其损伤程度与单因子作用一致,且染料的影响作用占主导.     

污泥加热预处理对中温厌氧消化的影响

对污泥加热预处理给中温厌氧混合消化和污泥单独消化带来的影响进行了研究.研究结果表明,污泥加热预处理有利于提高混合消化对 COD 的去除率,尤其是 SCOD 的去除率由 77%增长到 93%,但不利于 TS 和 VS 的去除;而对污泥单独消化,预处理则不利于有机物的去除.采用加热预处理后的污泥进样,混合消化和污泥单独消化的甲烷产气量均有所提高.     

铅锌矿区玉米中重金属污染特征及健康风险评价

以西南某铅锌矿区为研究区域,测定了92份玉米样品中Pb、Zn、Cd、Cr和Ni的含量,开展了矿区玉米籽粒中重金属污染特征及健康风险研究.应用单因子污染指数和内梅罗综合污染指数分析了重金属在玉米中的污染状况,采用健康风险评价模型评价了重金属对人体健康造成的风险,同时利用主成分分析法解析了重金属的主要来源.结果表明,玉米籽粒中Pb、Zn、Cd、Cr和Ni的平均含量分别为0.30、23.75、0.21、1.33和1.15 mg ·kg^-1;除重金属Zn外,其他4种重金属均超过我国食品卫生标准限值,研究区玉米籽粒中Pb、Cd、Cr和Ni的综合污染指数范围介于4.32~9.07之间,均属于重度污染,Zn的综合污染指数小于1;重金属通过玉米籽粒摄入引起的复合重金属污染对成人和儿童均存在健康风险,且对儿童造成的健康风险高于成人.玉米籽粒中5种重金属可以由2个主成分来反映,第一主成分主要支配Pb、Cd、Cr和Ni的来源,第二主成分支配Zn的来源.玉米籽粒重金属含量与土壤重金属含量之间没有明显相关性.     

河岸过滤中氨氮的削减及其浓度对细菌与氨氧化微生物的影响

通过小试滤柱模拟河岸过滤,结合荧光定量PCR和高通量测序等手段研究了河岸过滤对氨氮的削减效能和进水氨氮浓度对细菌与氨氧化微生物的影响.结果表明,低浓度（0.2 mg·L^-1）氨氮未被削减,较高浓度（1.0 mg·L^-1和2.0 mg·L^-1）氨氮的削减率可达70%.进水处细菌丰度随氨氮浓度升高而增加,细菌群落组成随氨氮浓度升高发生规律性变化.出水处氨氧化古菌（Ammonia oxidizing archaea,AOA）丰度与氨氮浓度呈负相关,氨氧化细菌（Ammonia oxidizing bacteria,AOB）丰度与氨氮浓度无显著相关关系;进水处AOA-α多样性与氨氮浓度呈正相关,但AOB-α多样性与氨氮浓度呈负相关;进水处AOA群落组成受氨氮浓度影响,而进、出水处AOB群落组成均受氨氮浓度影响.可见,进水氨氮浓度会影响河岸过滤对氨氮的削减效能,还会影响细菌、氨氧化微生物的丰度及群落结构,AOB对氨氮浓度的变化比AOA更敏感.     

离子液体吸收废印刷线路板热拆解过程中挥发性有机物——基于COSMO-RS模型

模拟废印刷线路板（WPCB）的热拆解过程,分析热拆解过程中的挥发性有机物（VOCs）组分;利用真实溶剂似导体屏蔽（COSMO-RS）模型对浓度较高的污染物进行量子力学模拟,研究离子液体（ILs）组成单元对目标污染物溶解度的影响差异,分析溶解过程中主导分子间作用力类型,确定优选吸收剂;测定不同溶剂进行溶解性,验证模型适用性.结果表明：①乙酸乙酯和环戊酮是浓度较高的VOCs组分,在240和250℃时浓度分别为43.1,153mg/m³和105,252mg/m³,质量百分比总和分别为76.3%和67.3%.②高表面屏蔽电荷密度分布峰、长烷基链阴阳离子和亲电基团的存在可提高乙酸乙酯和环戊酮在ILs中的溶解度.双三氟甲磺酰基亚胺盐（NTf₂^-）类ILs是一类优良吸收剂.静电力和范德华力对溶解过程起主导作用.③COSMO-RS模型可定性和半定量用于预测乙酸乙酯和环戊酮的溶解度.     

基于AIS轨迹修复的船舶排放空间表征改进方法与应用

基于船舶自动识别系统（Automatic Identification System,AIS）数据表征船舶排放是目前船舶排放空间表征的主流方法,但AIS船舶轨迹点缺失会造成船舶排放量低估和船舶空间分布表征错误,进而影响船舶排放控制区的划分.为改进船舶排放空间表征,本研究以2013年广东省AIS船舶数据为例,采用基于时间和经纬度的三次样条方法对AIS船舶轨迹进行修复,结合动力法计算船舶排放,分析对比AIS轨迹修复前后船舶排放表征的差异,并利用空气质量模型和卫星观测评估AIS轨迹修复对船舶排放表征和广东沿海空气质量模拟的改进效果.结果表明：轨迹修复后广东省海域船舶轨迹点总数由4685773个增至5746664个,船舶NO_x排放量增加了0.6%.对于轨迹点与排放缺失集中的粤东海域,轨迹修复后船舶轨迹点数增加了88%,NO_x排放量在广东省船舶排放量的占比提升至22%,特别是在粤东重点修复海域NO_x排放量增加了2.7倍.原始轨迹在广东省海域较为稀疏,在粤东海域有明显轨迹缺失;轨迹修复后广东省海域船舶轨迹更为密集,粤东海域船舶轨迹得以补充,船舶排放空间分布更连贯.对比模拟结果与卫星观测结果,轨迹修复后粤东重点修复海域船舶模拟浓度与观测浓度的偏差由51%减至6%,总体上船舶排放模拟结果更接近卫星观测结果.     

污泥生物炭去除水中重金属的研究进展

重金属带来的环境风险日益严峻,利用污泥生物炭去除水中重金属污染方面的研究得到了广泛关注。结合当前国内外研究现状,归纳了不同条件下制备的污泥生物炭对水中重金属,如Cd、Pb、Cr、As等的吸附机理,污泥生物炭对大多数重金属的吸附满足物理吸附和化学吸附的多重作用,可通过增加生物炭表面有效基团及有效吸附位点提升吸附性能。同时,总结了影响吸附效率的各种因素,探究了污泥生物炭的再生问题,并对今后污泥生物炭去除水中重金属的研究方向做出了展望。     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

Revealing the changes of bacterial community from water source to consumers tap: A full-scale investigation in eastern city of China

This study profiled the bacterial community variations of water from four water treatment systems, including coagulation, sedimentation, sand filtration, ozonation-biological activated carbon filtration (O₃-BAC), disinfection, and the tap water after the distribution process in eastern China. The results showed that different water treatment processes affected the bacterial community structure in different ways. The traditional treatment processes, including coagulation, sedimentation and sand filtration, reduced the total bacterial count, while they had little effect on the bacterial community structure in the treated water (before disinfection). Compared to the traditional treatment process, O₃-BAC reduced the relative abundance of Sphingomonas in the finished water. In addition, ozonation may play a role in reducing the relative abundance of Mycobacterium. NaClO and ClO₂ had different effects on the bacterial community in the finished water. The relative abundance of some bacteria (e.g. Flavobacterium, Phreatobacter and Porphyrobacter) increased in the finished water after ClO₂ disinfection. The relative abundance of Mycobacterium and Legionella, which have been widely reported as waterborne opportunistic pathogens, increased after NaClO disinfection. In addition, some microorganisms proliferated and grew in the distribution system, which could lead to turbidity increases in the tap water. Compared to those in the finished water, the relative abundance of Sphingomonas, Hyphomicrobium, Phreatobacter, Rheinheimera, Pseudomonas and Acinetobacter increased in the tap water disinfected with NaClO, while the relative abundance of Mycobacterium increased in the tap water disinfected with ClO₂. Overall, this study provided the detailed variation in the bacterial community in the drinking water system.