Simultaneous control of Hg0, SO2, and NOx by novel oxidized calcium-based sorbents

Efforts to develop multipollutant control strategies have demonstrated that adding certain oxidants to different classes of Ca-based sorbents leads to a significant improvement in elemental Hg vapor (Hg0), SO2, and NOx removal from simulated flue gases. In the study presented here, two classes of Ca-based sorbents (hydrated limes and silicate compounds) were investigated. A number of oxidizing additives at different concentrations were used in the Ca-based sorbent production process. The Hg0, SO2, and NOx capture capacities of these oxidant-enriched sorbents were evaluated and compared to those of a commercially available activated carbon in bench-scale, fixed-bed, and fluid-bed systems. Calcium-based sorbents prepared with two oxidants, designated C and M, exhibited Hg0 sorption capacities (approximately 100 microg/g) comparable to that of the activated carbon; they showed far superior SO2 and NOx sorption capacities. Preliminary cost estimates for the process utilizing these novel sorbents indicate potential for substantial lowering of control costs, as compared with other processes currently used or considered for control of Hg0, SO2, and NOx emissions from coal-fired boilers. The implications of these findings toward development of multipollutant control technologies and planned pilot and field evaluations of more promising multipollutant sorbents are summarily discussed.     

Hydroxychloroquine in COVID-19: therapeutic promises,current status,and environmental implications

Environmental Science and Pollution Research - The outbreak of novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has affected the entire world with its infectious spread and...     

Impact of different types of polluted irrigation water on soil fertility and wheat grain yield in clayey black soils of central India

This study was carried out in three different cities of western Madhya Pradesh (India) to investigate the effects of long-term irrigation with industrial waste water (IWW), contaminated groundwater (CGW), and untreated municipal sewage water (USW) on soil fertility as well as on wheat crop yield. Irrigation with these three types of polluted water increased organic matter content as well as contents of available P (with IWW and USW only), available K, available S, available Zn, available Cu (IWW only), and available Mn (IWW and CGW only). The magnitude of improvement in soil fertility status was the highest in the case of USW, followed by IWW and finally, by CGW. Concentrations of Na in wheat leaf tissue increased by 198 and 58 % whereas concentrations of Ca decreased significantly by 16 and 13 % due to the use of IWW and CGW, respectively, resulting in poor Ca nutrition to the crop. Although wheat grain yield increased considerably due to USW, the same recorded significant decreases with IWW and CGW. In spite of the enhancement in the available nutrient status, decrease in wheat grain yield with the use of IWW and CGW could be due to the build-up of salts in the soil and an imbalance in the Na/Ca ratio in wheat crops irrigated with IWW and CGW. The adverse effect on wheat productivity was more pronounced with IWW as compared to CGW.     

Ggum-poly(Itaconic Acid) Based Superabsorbents Via Two-Step Free-Radical Aqueous Polymerization for Environmental and Antibacterial Applications

Ggum-based conducting hydrogels possessing dye removal and antibacterial property were developed by two-step free-radical aqueous polymerization method. Conductivity was introduced with polyaniline (PANI) chains incorporated within the crosslinked network of Ggum-poly(itaconic acid) superabsorbent. The material properties of the synthesized samples were characterized using FTIR spectroscopy, thermal analysis and scanning electron microscopy techniques. Results showed that synthesized samples exhibited the best antibacterial activity against Gram-positive bacteria. Synthesized samples were found to be effective in removal of toxic methylene blue (MB) dye from the waste water. The adsorption kinetics of superabsorbents has been described by using pseudo first and pseudo second order kinetics models. Furthermore, application of hydrogels to improve the water retention properties of different soils was also studied for agricultural purpose.     

Assessment of physicochemical characteristics of Ganga Canal water quality in Uttarakhand

Assessment of physicochemical parameters of Ganga Canal water was carried out during 2012–2013 at Haridwar (Uttarakhand) with two different sites, i.e., Bhimgoda Barrage (site 1—control site) and Bahadrabad (site 2—contaminated site), where canal water flows with loads of pollution from highly commercial and industrial areas. During investigation, maximum turbidity (287.72 ± 56.28 JTU), total solids (1167.60 ± 303.90 mg l^?1), free CO₂ (1.88 ± 0.22 mg l^?1), total hardness (60.14 ± 1.13 mg l^?1), pH (7.1 ± 0.13), nitrate (0.048 ± 0.010), nitrite (0.019 ± 0.001), biochemical oxygen demand (2.866 ± 1.098), chemical oxygen demand (6.8 ± 2.61) and phosphate (0.087 ± 0.015), while minimum velocity (1.71 ± 0.19 ms^?1), transparency (0.12 ± 0.08 m) and dissolved oxygen (7.95 ± 0.44 mg l^?1) were recorded in monsoon season at site 2 in comparison with site 1. The mean values of these parameters were compared with WHO and ISI standards and found significant differences (p < 0.05) in the mean values of turbidity, total solids, pH, dissolved oxygen, free CO₂ and total hardness with sampling sites. The turbidity of both the sites 1 and 2 was recorded above the permissible limit. Turbidity of site 2 is much higher than of site 1, so it is counted as more polluted. The values of the studied parameters were more during monsoon season and summer season at site 2 as compared to site 1. The results indicated that most of the physicochemical parameters from Ganga Canal system were within or at periphery in comparison with permissible limit of ISI and WHO for drinking water and therefore may be suitable for domestic purposes, but it requires perceptible consideration due to intense changes in climate and increase in pollution.     

Application of ameliorated wood pulp to recover Cd(II), Pb(II), and Ni(II) from e-waste

In this study, dl-malic acid and hydrogen peroxide were used as leaching agents to remove metals from e-waste (printed-circuit boards) and itaconic acid-grafted poly(vinyl alcohol)-encapsulated wood pulp (IA-g-PVA-en-WP) to uptake metals from leachate with high proficiency [11.63 mg g^?1; 93.03 % for Cd(II), 11.90 mg g^?1; 95.18 % for Pb(II), and 12.14 mg g^?1; 97.08 % for Ni(II)]. Metals were recovered from the loaded biosorbent by desorption studies. The standard analytical techniques, such as elemental analysis, Fourier-transform-infrared spectroscopy, scanning electron microscopy, atomic force microscopy, and thermogravimetric analysis, were used to characterize the recovering agent (biosorbent). At equilibrium, the metal uptake data were fitted to Langmuir and D–R isotherms (R ² > 0.99) significantly, revealing, the homogeneous distribution of active sites on biosorbent’s backbone. The possible mechanism appeared to be ion exchanges of metal ions with H⁺ together with binding over functionalities (COO^?). Dimensionless equilibrium parameter (R _L) showed the favourability of metal uptake at lower concentration, while mean adsorption energy (E) certified the physical binding of metal on functionalities which was further confirmed by sticking probability and activation energy parameters. Reusability studies were also conducted to state the performance of biosorbent.     

Study of ultrasonic assisted cryogenically cooled EDM process using sintered (Cu–TiC) tooltip

In most EDM operations, the maximum contribution in the total operation cost is the tool cost. Electrode wear is a major problem in EDM process. Therefore, in this paper, the process performance of sintered copper (Cu)–titanium carbide (TiC) electrode tip in ultrasonic assisted cryogenically cooled electrical discharge machining (UACEDM) has been studied. The performance parameters studied in this paper are electrode wear ratio (EWR), material removal rate (MRR), surface roughness (SR), out of roundness and surface integrity. The process parameters considered in this study are discharge current, pulse on time, duty cycle and gap voltage. Cermet was fabricated, having copper content of 75% and titanium carbide content of 25%, by mixing, pressing, and sintering. The performance of the newly formed cermet electrode tip is compared with conventional copper electrode tip for UACEDM process and analyzed. It has been observed that EWR and out of roundness decreases when cermet electrode tip is used as compared to conventional tooltip. It has also been observed that MRR and SR increase when cermet tooltip is used. The surface cracks density and crack width on workpiece machined by cermet tooltip have been found to be lesser as compared to the specimen machined by conventional tooltip.