Development of Federal Air Standards to Reduce Sulfur Dioxide Emissions from New Industrial Boilers

Federal new source performance standards to control air emissions of sulfur dioxide from new industrial boilers were proposed by EPA on June 19, 1986. These standards would require boiler owners to reduce SO₂ emissions by 90 percent and meet an emission limit of 1.2 lb/MM Btu of heat input for coal-fired boilers and 0.8 lb/MM Btu for oil-fired boilers. In developing these standards, several regulatory options were considered, from standards that could be met by firing low sulfur fuels to standards that would necessitate flue gas treatment. The environmental, economic, and cost impacts of each option were analyzed. National impacts were estimated by a computer model that projects the population of new boilers over the 5-year period following proposal, predicts the compliance strategy that will be used to comply with the particular option (always assuming that the lowest cost method of compliance will be selected), and estimates the resulting emission reductions and costs. Impacts on specific industries and on model boilers were also analyzed. This paper focuses on these analyses and their results. The Agency's conclusions from these analyses, which led to the decision to establish percent reduction standards, are provided, and the proposed SO₂ standards are summarized. The proposed standards also include an emission limit for particulate matter from oil-fired boilers (0.1 lb/MM Btu). However, this article focuses only on the SO₂ standards.     

Low Concentration Mercury Sorption Mechanisms and Control by Calcium-Based Sorbents: Application in Coal-Fired Processes

ABSTRACT

The capture of elemental mercury (Hg⁰) and mercuric chloride (HgCl₂) by three types of calcium (Ca)-based sor-bents was examined in this bench-scale study under conditions prevalent in coal-fired utilities. Ca-based sorbent performances were compared with that of an activated carbon. Hg⁰ capture of about 40% (nearly half that of the activated carbon) was achieved by two of the Ca-based sorbents. The presence of sulfur dioxide (SO₂) in the simulated coal combustion flue gas enhanced the Hg⁰ capture from about 10 to 40%. Increasing the temperature in the range of 65-100 °C also caused an increase in the Hg⁰ capture by the two Ca-based sorbents. Mercuric chloride (HgCl₂) capture exhibited a totally different pattern. The presence of SO₂ inhibited the HgCl₂ capture by Ca-based sorbents from about 25 to less than 10%. Increasing the temperature in the studied range also caused a decrease in HgCl₂ capture. Upon further pilot-scale confirmations, the results obtained in this bench-scale study can be used to design and manufacture more cost-effective mercury sorbents to replace conventional sorbents already in use in mercury control.     

Development and Pilot Plant Evaluation of Silica- Enhanced Lime Sorbents for Dry Flue Gas Desulfurization

EPA’s efforts to develop low cost, retrofitable flue gas cleaning technology include the development of highly reactive sorbents. Recent work addressing lime enhancement and testing at the bench-scale followed by evaluation of the more promising sorbents in a pilot plant are discussed here.

The conversion of Ca(OH)₂ with SO₂ increased several-fold compared with Ca(OH)₂ alone when Ca(OH)₂ was slurrled with fly ash first and later exposed to SO₂ in a laboratory packed bed reactor. Ca(OH)₂ enhancement increased with the increased fly ash amount. Dlatomaceous earths were very effective reactivity promoters of lime-based sorbents. Differential scanning calorimetry of the promoted sorbents revealed the formation of a new phase (calcium silicate hydrates) after hydration, which may be the basis for the observed Improved SO₂ capture.

Fly ash/lime and diatomaceous earth/lime sorbents were tested in a 100 m³/h pilot facility incorporating a gas humidifier, a sorbent duct injection system, and a baghouse. The inlet SO₂ concentration range was 1000-2500 ppm. With once-through dry sorbent injection into the humidified flue gas [approach to saturation 10–20°C (18–36°F) in the baghouse], the total SO₂ removal ranged from 50 to 90 percent for a stoichiometric ratio of 1 to 2. Recycling the collected solids resulted in a total lime utilization exceeding 80–90 percent. Increased lime utilization was also investigated by the use of additives.     

Simultaneous control of Hg0, SO2, and NOx by novel oxidized calcium-based sorbents

Efforts to develop multipollutant control strategies have demonstrated that adding certain oxidants to different classes of Ca-based sorbents leads to a significant improvement in elemental Hg vapor (Hg0), SO2, and NOx removal from simulated flue gases. In the study presented here, two classes of Ca-based sorbents (hydrated limes and silicate compounds) were investigated. A number of oxidizing additives at different concentrations were used in the Ca-based sorbent production process. The Hg0, SO2, and NOx capture capacities of these oxidant-enriched sorbents were evaluated and compared to those of a commercially available activated carbon in bench-scale, fixed-bed, and fluid-bed systems. Calcium-based sorbents prepared with two oxidants, designated C and M, exhibited Hg0 sorption capacities (approximately 100 microg/g) comparable to that of the activated carbon; they showed far superior SO2 and NOx sorption capacities. Preliminary cost estimates for the process utilizing these novel sorbents indicate potential for substantial lowering of control costs, as compared with other processes currently used or considered for control of Hg0, SO2, and NOx emissions from coal-fired boilers. The implications of these findings toward development of multipollutant control technologies and planned pilot and field evaluations of more promising multipollutant sorbents are summarily discussed.     

Simultaneous Control of Hg0, SO2, and NOx by Novel Oxidized Calcium-Based Sorbents

Abstract

Efforts to develop multipollutant control strategies have demonstrated that adding certain oxidants to different classes of Ca-based sorbents leads to a significant improvement in elemental Hg vapor (Hg⁰), SO₂, and NO_x removal from simulated flue gases. In the study presented here, two classes of Ca-based sorbents (hydrated limes and silicate compounds) were investigated. A number of oxidizing additives at different concentrations were used in the Ca-based sorbent production process. The Hg⁰, SO₂, and NO_x capture capacities of these oxidant-enriched sorbents were evaluated and compared to those of a commercially available activated carbon in bench-scale, fixed-bed, and fluid-bed systems. Calcium-based sorbents prepared with two oxidants, designated C and M, exhibited Hg⁰ sorp-tion capacities (~100 μg/g) comparable to that of the activated carbon; they showed far superior SO₂ and NO_x sorption capacities. Preliminary cost estimates for the process utilizing these novel sorbents indicate potential for substantial lowering of control costs, as compared with other processes currently used or considered for control of Hg⁰, SO₂, and NO_x emissions from coal-fired boilers. The implications of these findings toward development of multipollutant control technologies and planned pilot and field evaluations of more promising multipollutant sorbents are summarily discussed.     

Preliminary Estimates of Performance and Cost of Mercury Control Technology Applications on Electric Utility Boilers

ABSTRACT

Under the Clean Air Act Amendments of 1990, the U.S. Environmental Protection Agency (EPA) determined that regulation of mercury emissions from coal-fired power plants is appropriate and necessary. To aid in this determination, preliminary estimates of the performance and cost of powdered activated carbon (PAC) injection-based mercury control technologies were developed. This paper presents these estimates and develops projections of costs for future applications.

Cost estimates were developed using PAC to achieve a minimum of 80% mercury removal at plants using electrostatic precipitators and a minimum of 90% removal at plants using fabric filters. These estimates ranged from 0.305 to 3.783 mills/kWh. However, the higher costs were associated with a minority of plants using hot-side electrostatic precipitators (HESPs). If these costs are excluded, the estimates range from 0.305 to 1.915 mills/kWh. Cost projections developed using a composite lime-PAC sorbent for mercury removal ranged from 0.183 to 2.270 mills/kWh, with the higher costs being associated with a minority of plants that used HESPs.     

Current Status of the ADVACATE Process for Flue Gas Desulfurization

The following report discusses current bench- and pilot-plant advances in preparation of ADVAnced siliCATE (ADVACATE) calcium silicate sorbents for flue gas desulfurization. It also discusses current bench- and pilot-plant advances in sorbent preparation. Fly ash was ground in a laboratory scale grinder prior to slurring in order to decrease the slurring time needed for the sorbent to be reactive with SO₂. Reactivity of ADVACATE sorbents with SO₂ in the bench-scale reactor correlated with their surface area.

ADVACATE sorbents produced with ground fly ash were evaluated in the 50 cfm (85 m³/h) pilot plant providing 2 s duct residence time. ADVACATE sorbent was produced by slurrying ground fly ash (median particle size of 4.3 µm) with Ca(OH)₂ at the weight ratio of 3:1 at 90°C (194°F) for 3hto yield solids with 30 weight percent of initial free moisture. When this sorbent was injected into the duct with 1500 ppm SO₂ and at 11°C (20°F) approach to saturation, the measured SO₂ removal was approximately 60percent at a Ca/S stoichiometric ratio of 2. Previously, when ADVACATE sorbent was produced at 90°C (194°F) and at the same fly-ash-to-Ca(OH)₂ weight ratio using unground fly ash, removal under the same conditions in the duct was approximately 50 percent following 12 h slurring. The report presents the results of pilot-scale recycle tests at the recycle ratio of 2. Finally, the report discusses future U.S. Environmental Protection Agency plans for commercialization of ADVACATE.     

Silica-Enhanced Sorbents for Dry Injection Removal of SO2 from Flue Gas

Novel silica-enhanced lime sorbents were tested in a bench-scale sand-bed reactor for their potential for SO₂ removal from flue gas. Reactor conditions were 64°C (147°F), relative humidity of 60 percent [corresponding to an approach to saturation temperature of 10°C (18°F)], and inlet SO₂ concentration of 500 or 1000 ppm. The sorbents were prepared by pressure hydration of CaO or Ca(OH)₂ with siliceous materials at 100°C (101 kPa) [212°F (14.7 psi)] to 230°C (2793 kPa) [446°F (405 psi)] for 15 min to 4 h. Pressure hydration fostered the formation of a sorbent reactive with SO₂ from fly ash and Ca(OH)₂ in a much shorter time than did atmospheric hydration. The conversion of Ca(OH)₂ in the sand-bed reactor increased with the increasing weight ratio of fly ash to lime and correlated well with B.E.T. surface area, increasing with increasing surface area. The optimum temperature range for the pressure-hydration of fly ash with Ca(OH)₂ was between 110 and 160°C (230 and 320 °F). The pressure hydration of diatomaceous earth with CaO did not offer significant reactivity advantages over atmospheric hydration; however, the rate of enhancement of Ca(OH)₂ conversions was much faster with pressure hydration. Scanning electron microscope (SEM) and x-ray diffraction studies showed solids of different morphology with different fly ash/lime ratios and changing conditions of pressure hydration.     

The first world conservation lecture

Summary This, The First World Conservation Lecture, was presented at the Royal Institution, London, UK, on 12 March 1981. The Lecture celebrated the 20th anniversary of the World Wildlife Fund, and the first anniversary of the World Conservation Strategy. The Lecture was organized by the World Wildlife Fund, UK.Published with the kind permission of the World Wildlife Fund, UK.Edward Max Nicholson, CB, CVO, Commandeur (Netherlands), Order of the Golden Ark, holds honorary doctorates from the University of Aberdeen, and The Royal College of Art London. He was educated at the University of Oxford, and was a member of the University's expeditions to Greenland (1928) and to British Guiana (1929). He was General Secretary (until 1940), later Chairman of PEP (Political and Economic Planning): now Vice-President of its successor body, the Policy Studies Institute. From 1945 to 1952 he was Secretary of the Office of the Lord President of the Council, then Deputy Prime Minister of the United Kingdom. He was member of the Advisory Council on Scientific Policy from 1948–1964. In 1952 he was leader of the joint UN/FAO Development Team in Baluchistan. Charter Member from 1949, and Director-General (1952–1966) of the Nature Conservancy, London, UK. From 1963 to 1974 he was Convenor of the Conservation Section of the International Council of Scientific Unions' International Biological Programme. President of the IUCN Technical Meeting in Edinburgh in 1956, concerned with rehabilitation of areas biologically devastated by human disturbance, and relation of ecology to landscape planning. Member, Panel on Landscape Action Program, The White House Conference (USA) on Natural Beauty (1965). Secretary, HRH The Duke of Edinburgh's Study Conference on The Countryside in 1970 (1963 and 1965). Council and Board Member of IIED. Godman-Salvin Medallist British Ornithologist Unions. Phillips Medallist and Member of Honour IUCN, Geoffroy St. Hilaire Gold Medal, Société Nationale de Protection de Nature de France, Premio Europeo Cortina-Ulisse (1971), Europa Preis für Landespflege (1972), Hon Member of World Wildlife Fund, Chairman Ecological Parks Trust, President RSPB, 1980. Principal Consultant and Chairman of Land Use Consultants Ltd (London) since 1966. Author of many books,Birds and Men (1951);Britain's Nature Reserves (1958),The System (1967);The Environmental Revolution (1970).     

Preliminary estimates of performance and cost of mercury control technology applications on electric utility boilers.

Under the Clean Air Act Amendments of 1990, the U.S. Environmental Protection Agency (EPA) determined that regulation of mercury emissions from coal-fired power plants is appropriate and necessary. To aid in this determination, preliminary estimates of the performance and cost of powdered activated carbon (PAC) injection-based mercury control technologies were developed. This paper presents these estimates and develops projections of costs for future applications. Cost estimates were developed using PAC to achieve a minimum of 80% mercury removal at plants using electrostatic precipitators and a minimum of 90% removal at plants using fabric filters. These estimates ranged from 0.305 to 3.783 mills/kWh. However, the higher costs were associated with a minority of plants using hot-side electrostatic precipitators (HESPs). If these costs are excluded, the estimates range from 0.305 to 1.915 mills/kWh. Cost projections developed using a composite lime-PAC sorbent for mercury removal ranged from 0.183 to 2.270 mills/kWh, with the higher costs being associated with a minority of plants that used HESPs.