漓江流域δD和δ18O对蒸发的指示作用

以漓江流域为例查明不同水体之间氢氧稳定同位素组成特征,并探讨氢氧稳定同位素对漓江流域的蒸发过程指示作用.结果表明：流域内不同水体之间,氢氧稳定同位素表现出不同的组成特征,地表水和地下水,在丰水期δD值和δ¹⁸O值要比枯水期更容易富集,地下水的δD值和δ¹⁸O值分布范围较地表水小;随着水温的升高,δ¹⁸O的变化趋势比d-excess明显.从漓江上游到下游高程逐渐下降,河水线的斜率和截距也在逐渐减小,其中漓江下游河水线的斜率和截距要低于当地大气降水线,表明下游受到蒸发作用较强烈;地下河水线、地表河水线在一定程度上偏离当地大气降水线,但偏离程度较小,表明三者之间有很好的水力联系.受温度和湿度的共同影响,漓江干流丰水期河水的蒸发量占最初水体总量的0.7%~9.1%,枯水期河水的蒸发量占最初水体总量的2.6%~9.7%,丰水期的蒸发比例低于枯水期,从上游到下游蒸发比例在逐渐上升.研究区蒸发量估算值为959.40mm,与多年实测值少43.11mm,相对误差4.70%.氢氧稳定同位素对研究区降水、地表水、地下水之间的转换规律具有重要的实际意义,在今后的漓江流域水文研究中有着更加广阔的空间.     

离子液体吸收废印刷线路板热拆解过程中挥发性有机物——基于COSMO-RS模型

模拟废印刷线路板（WPCB）的热拆解过程,分析热拆解过程中的挥发性有机物（VOCs）组分;利用真实溶剂似导体屏蔽（COSMO-RS）模型对浓度较高的污染物进行量子力学模拟,研究离子液体（ILs）组成单元对目标污染物溶解度的影响差异,分析溶解过程中主导分子间作用力类型,确定优选吸收剂;测定不同溶剂进行溶解性,验证模型适用性.结果表明：①乙酸乙酯和环戊酮是浓度较高的VOCs组分,在240和250℃时浓度分别为43.1,153mg/m³和105,252mg/m³,质量百分比总和分别为76.3%和67.3%.②高表面屏蔽电荷密度分布峰、长烷基链阴阳离子和亲电基团的存在可提高乙酸乙酯和环戊酮在ILs中的溶解度.双三氟甲磺酰基亚胺盐（NTf₂^-）类ILs是一类优良吸收剂.静电力和范德华力对溶解过程起主导作用.③COSMO-RS模型可定性和半定量用于预测乙酸乙酯和环戊酮的溶解度.     

裂解温度和离子强度对不同来源生物炭胶体释放行为的影响

近年来环境中生物炭胶体形成受到广泛关注,它是生物炭在环境中物理分解作用的重要过程,对污染物迁移有着重要影响.然而,目前对生物炭胶体释放过程和影响因素的研究甚少,人们对生物炭胶体释放机理的认识还很有限.本研究以小麦秸秆和花生壳为生物质来源,系统地探讨了生物炭的裂解温度（300~700 ℃）和溶液离子强度（0.1~10 mmol·L^-1）对生物炭胶体产率的影响.结果表明,随着裂解温度的升高,生物炭的耐磨性增强,且在较高的裂解温度下（≥500 ℃）花生壳生物炭的耐磨性显著强于小麦秸秆生物炭.生物炭的胶体产率受到生物质来源和裂解温度的显著影响,花生壳生物炭的胶体产率低于小麦秸秆生物炭,高温裂解（≥600 ℃）生物炭的胶体产率显著低于中低温裂解生物炭.在相同溶液离子强度下,生物炭胶体产率与其亚微米级碎片率呈显著正相关（p<0.05）,即生物炭中亚微米级碎片率越高,生物炭胶体产率越高.当溶液离子强度从1 mmol·L^-1增加到10 mmol·L^-1时,两种来源生物炭的胶体产率均显著降低,其降低的程度因生物炭裂解温度而异,其中低温裂解（300 ℃）生物炭的胶体产率降低了11.1%~11.2%,中高温裂解（≥ 500 ℃）生物炭的胶体产率降低了60.0%~97.2%.     

基于AIS轨迹修复的船舶排放空间表征改进方法与应用

基于船舶自动识别系统（Automatic Identification System,AIS）数据表征船舶排放是目前船舶排放空间表征的主流方法,但AIS船舶轨迹点缺失会造成船舶排放量低估和船舶空间分布表征错误,进而影响船舶排放控制区的划分.为改进船舶排放空间表征,本研究以2013年广东省AIS船舶数据为例,采用基于时间和经纬度的三次样条方法对AIS船舶轨迹进行修复,结合动力法计算船舶排放,分析对比AIS轨迹修复前后船舶排放表征的差异,并利用空气质量模型和卫星观测评估AIS轨迹修复对船舶排放表征和广东沿海空气质量模拟的改进效果.结果表明：轨迹修复后广东省海域船舶轨迹点总数由4685773个增至5746664个,船舶NO_x排放量增加了0.6%.对于轨迹点与排放缺失集中的粤东海域,轨迹修复后船舶轨迹点数增加了88%,NO_x排放量在广东省船舶排放量的占比提升至22%,特别是在粤东重点修复海域NO_x排放量增加了2.7倍.原始轨迹在广东省海域较为稀疏,在粤东海域有明显轨迹缺失;轨迹修复后广东省海域船舶轨迹更为密集,粤东海域船舶轨迹得以补充,船舶排放空间分布更连贯.对比模拟结果与卫星观测结果,轨迹修复后粤东重点修复海域船舶模拟浓度与观测浓度的偏差由51%减至6%,总体上船舶排放模拟结果更接近卫星观测结果.     

基于RF-LSTM的鸡舍恶臭气体预测研究

以鸡舍氨气为研究对象,对鸡舍氨气预测模型进行了研究.首先,利用随机森林算法（RF）对影响鸡舍氨气浓度的环境变量进行重要性排序,选取温度、湿度、光照、气象温度、降雨量作为模型的输入变量;在此基础上,构建了基于长短时记忆神经网络（LSTM）的鸡舍氨气浓度预测模型,并将提出的预测模型应用于江苏省宜兴市某养鸡场的氨气浓度预测中,并与LSTM模型、RF-Elman模型和RF-BP模型进行了对比实验,结果表明,基于RF-LSTM模型的预测效果最好,其平均绝对误差（MAE）、平均绝对百分误差（MAPE）和均方根误差（RMSE）分别为0.9183、4.9637%和1.4262;同时,为了验证该模型的性能,本文还实现了不同时间尺度的鸡舍氨气浓度预测,提前2h、3h、4h、5h氨气预测的平均绝对误差（MAE）分别为1.6218、2.1991、2.8553和3.0677.本文提出的预测模型提高了鸡舍氨气浓度的预测精度,可为减少鸡舍恶臭气体排放提供科学依据.     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

污泥生物炭去除水中重金属的研究进展

重金属带来的环境风险日益严峻,利用污泥生物炭去除水中重金属污染方面的研究得到了广泛关注。结合当前国内外研究现状,归纳了不同条件下制备的污泥生物炭对水中重金属,如Cd、Pb、Cr、As等的吸附机理,污泥生物炭对大多数重金属的吸附满足物理吸附和化学吸附的多重作用,可通过增加生物炭表面有效基团及有效吸附位点提升吸附性能。同时,总结了影响吸附效率的各种因素,探究了污泥生物炭的再生问题,并对今后污泥生物炭去除水中重金属的研究方向做出了展望。     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

Performance of different macrophytes in the decontamination of and electricity generation from swine wastewater via an integrated constructed wetland-microbial fuel cell process

Plants constitute a major element of constructed wetlands(CWs).In this study,a coupled system comprising an integrated vertical flow CW(IVCW) and a microbial fuel cell(MFC) for swine wastewater tre atment was developed to research the effects of macrophytes commonly employed in CWs,Canna indica,Acorus calamus,and Ipomoea aquatica,on decontamination and electricity production in the system.Because of the different root types and amounts of oxygen released by the roots,the rates of chemical oxygen demand(COD) and ammonium nitrogen(NH_4~+-N) removal from the swine wastewater differed as well.In the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,the COD removal rates were 80.20%,88.07%,84.70%,and 82.20%,respectively,and the NH_4~+-N removal rates were 49.96%,75.02%,70.25%,and 68.47%,respectively.The decontamination capability of the Canna indica system was better than those of the other systems.The average output voltages were 520±42,715±20,660±27,and 752±26 mV for the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,respectively,and the maximum power densities were 0.2230,0.4136,0.3614,and0.4964 W/m~3,respectively.Ipomoea aquatica had the largest effect on bioelectricity generation promotion.In addition,electrochemically active bacteria,Geobacter and Desulfuromonas,were detected in the anodic biofilm by high-throughput sequencing analysis,and Comamonas(Proteobacteria),which is widely found in MFCs,was also detected in the anodic biofilm.These results confirmed the important role of plants in IVCW-MFCs.