Monitoring contaminants from oil production at sea by measuring gill EROD activity in Atlantic cod (Gadus morhua)

An ex vivo gill EROD assay was applied in Atlantic cod (Gadus morhua) as a biomarker for waterborne CYP1A-inducing compounds derived from oil production at sea. Exposure to nominal concentrations of 1 ppm or 10 ppm North Sea crude oil in a static water system for 24 h caused a concentration-dependent gill EROD induction. Further, exposure of cod for 14 days to environmentally relevant concentrations of produced water (PW, diluted 1:200 or 1:1000) from a platform in the North Sea using a flow-through system resulted in a concentration-dependent induction of gill EROD. Crude oil (0.2 ppm) from the same oil field also proved to induce EROD. Finally, gill EROD activity in cod caged for 6 weeks at 500-10 000 m from two platforms outside Norway was measured. The activities in these fish were very low and did not differ from those in fish caged at reference sites.     

Bioenergy to save the world

BACKGROUND AND AIM: Following to the 2006 climate summit, the European Union formally set the goal of limiting global warming to 2 degrees Celsius. But even today, climate change is already affecting people and ecosystems. Examples are melting glaciers and polar ice, reports about thawing permafrost areas, dying coral reefs, rising sea levels, changing ecosystems and fatal heat periods. Within the last 150 years, CO2 levels rose from 280 ppm to currently over 400 ppm. If we continue on our present course, CO2 equivalent levels could approach 600 ppm by 2035. However, if CO2 levels are not stabilized at the 450-550 ppm level, the consequences could be quite severe. Hence, if we do not act now, the opportunity to stabilise at even 550 ppm is likely to slip away. Long-term stabilisation will require that CO2 emissions ultimately be reduced to more than 80% below current levels. This will require major changes in how we operate. RESULTS: Reducing greenhouse gases from burning fossil fuels seems to be the most promising approach to counterbalance the dramatic climate changes we would face in the near future. It is clear since the Kyoto protocol that the availability of fossil carbon resources will not match our future requirements. Furthermore, the distribution of fossil carbon sources around the globe makes them an even less reliable source in the future. We propose to screen crop and non-crop species for high biomass production and good survival on marginal soils as well as to produce mutants from the same species by chemical mutagenesis or related methods. These plants, when grown in adequate crop rotation, will provide local farming communities with biomass for the fermentation in decentralized biogas reactors, and the resulting nitrogen rich manure can be distributed on the fields to improve the soil. DISCUSSION: Such an approach will open new economic perspectives to small farmers, and provide a clever way to self sufficient and sustainable rural development. Together with the present economic reality, where energy and raw material prices have drastically increased over the last decade, they necessitate the development and the establishment of alternative concepts. CONCLUSIONS: Biotechnology is available to apply fast breeding to promising energy plant species. It is important that our valuable arable land is preserved for agriculture. The opportunity to switch from low-income agriculture to biogas production may convince small farmers to adhere to their business and by that preserve the identity of rural communities. PERSPECTIVES: Overall, biogas is a promising alternative for the future, because its resource base is widely available, and single farms or small local cooperatives might start biogas plant operation.     

Heavy metal contamination in the vicinity of an industrial area near Bucharest

BACKGROUND, AIMS AND SCOPE: Chromium enters into the aquatic environment as a result of effluent discharge from steel works, electroplating, leather tanning industries and chemical industries. As the Cr(VI) is very harmful to living organisms, it should be quickly removed from the environment when it happens to be contaminated. Therefore, the aim of this laboratory research was to develop a rapid, simple and adaptable solvent extraction system to quantitatively remove Cr(VI) from polluted waters. METHODS: Aqueous salt-solutions containing Cr(VI) as CrO4(2-) at ppm level (4-6 ppm) were prepared. Equal volumes (5 ml) of aqueous and organic (2-PrOH) phases were mixed in a 10 ml centrifuge tube for 15 min, centrifuged and separated. Concentrations of Cr(VI), in both the aqueous and organic phases, were determined by atomic absorption spectrometry. The effects of salt and acid concentrations, and phase-contact time on the extraction of Cr(VI) were investigated. In addition, the extraction of Cr(VI) was assessed in the presence of tetramethylammonium chloride (TMAC) in 2-PrOH phase. Effects of some other metals, (Cd(II), Co(II), Cu(II), Ni(II) and Zn(II)), on the extraction of Cr(VI) were also investigated. RESULTS AND DISCUSSION: The Cr(VI) at ppm level was extracted quantitatively by salting-out the homogeneous system of water and 2-propanol(2-PrOH) using chloride salts, namely CaCl2 or NaCl, under acidic chloride media. The extracted chemical species of Cr(VI) was confirmed to be the CrO3Cl-. The ion-pair complex extracted into the organic phase was rationalized as the solvated ion-pair complex of [2-PrOH2+, CrO3Cl-]. The complex was no longer stable. It implied the reaction between extracted species. Studies revealed that salts and acid directly participated in the formation of the above complex. Use of extracting agents (TMAC) didn't show any significant effect on the extraction of Cr(VI) under high salting-out conditions. There is no significant interference effect on the extraction of Cr(VI) by the presence of other metals. The Cr(VI) in the organic phase was back-extracted using an aqueous ammonia solution (1.6 mol dm(-3)) containing 3 mol dm(-3) NaCl. The extraction mechanism of Cr(VI) is also discussed. CONCLUSIONS: Salting-out of homogeneous mixed solvent of 2-propanol can be employed to extract Cr(VI) quantitatively, as an ion-pair of [2-PrOH2+ * CrO3Cl-] solvated by 2-PrOH molecules. Then, the complex becomes 'solvent-like' and is readily separated into the organic phase. The increase of Cl- ion concentration in the aqueous phase favors the extraction. The 2-PrOH, salts and acid play important roles in the extraction process. There is no need to use an extracting agent at a high salting-out condition. RECOMMENDATIONS AND PERSPECTIVES: Chromium(VI) must be quickly removed before it enters into the natural cycle. As the 2-PrOH is water-miscible in any proportion, ion-pairing between 2-PrOH2+ and CrO3Cl- becomes very fast. As a result, Cr(VI) can easily be extracted. Therefore, the method is recommended as a simple, rapid and adaptable method to quickly separate Cr(VI) from aqueous samples.     

A fluorescence-based bioassay for aquatic macrophytes and its suitability for effect analysis of non-photosystem II inhibitors

Background, Goals and Scope During the last years the miniaturization of toxicity test systems for rapid and parallel measurements of large quantities of samples has often been discussed. For unicellular algae as well as for aquatic macrophytes, fluorescence-based miniaturized test systems have been introduced to analyze photosystem II (PSII) inhibitors. Nevertheless, high-throughput screening should also guarantee the effect detection of a broad range of toxicants in order to ensure routinely applicable, high-throughput measuring device experiments which can cover a broad range of toxicants and modes of action others than PSII inhibition. Thus, the aim of this study was to establish a fast and reproducible measuring system for non-PSII inhibitors for aquatic macrophyte species to overcome major limitations for use. Methods A newly developed imaging pulse-amplitude-modulated chlorophyll fluorometer (I-PAM) was applied as an effect detector in short-term bioassays with the aquatic macrophyte species Lemna minor. This multiwell-plate based measuring device enabled the incubation and measurement of up to 24 samples in parallel. The chemicals paraquat-dichloride, alizarine and triclosan were chosen as representatives for the toxicant groups of non-PSII herbicides, polycyclic aromatic hydrocarbons (PAHs) and pharmaceuticals and personal care products (PPCPs), which are often detected in the aquatic environment. The I-PAM was used (i) to establish and validate the sensitivity of the test system to the three non-PSII inhibitors, (ii) to compare the test systems with standardized and established biotests for aquatic macrophytes, and (iii) to define necessary time scales in aquatic macrophyte testing. For validation of the fluorescence-based assay, the standard growth test with L. minor (ISO/DIS 20079) was performed in parallel for each chemical. Results The results revealed that fluorescence-based measurements with the I-PAM allow rapid and parallel analysis of large amounts of aquatic macrophyte samples. The I-PAM enabled the recording of concentration-effect-curves with L. minor samples on a 24-well plate with single measurements. Fluorescence-based concentration-effect-curves could be detected for all three chemicals after only 1 h of incubation. After 4–5 h incubation time, the maximum inhibition of fluorescence showed an 80–100% effect for the chemicals tested. The EC50 after 24 h incubation were estimated to be 0.06 mg/L, 0.84 mg/L and 1.69 mg/L for paraquatdichloride, alizarine and triclosan, respectively. Discussion The results obtained with the I-PAM after 24 h for the herbicide paraquat-dichloride and the polycyclic aromatic hydrocarbon alizarine were in good accordance with median effective concentrations (EC50s) obtained by the standardized growth test for L. minor after 7 d incubation (0.09 mg/L and 0.79 mg/L for paraquat-dichloride and alizarine, respectively). Those results were in accordance with literature findings for the two chemicals. In contrast, fluorescence-based EC50 of the antimicrobial agent triclosan proved to be two orders of magnitude greater when compared to the standard growth test with 7 d incubation time (0.026 mg/L) as well as with literature findings. Conclusion Typically, aquatic macrophyte testing is very time consuming and relies on laborious experimental set-ups. The I-PAM measuring device enabled fast effect screening for the three chemicals tested. While established test systems for aquatic macrophytes need incubation times of ≥ 7 d, the I-PAM can detect inhibitory effects much earlier (24 h), even if inhibition of chemicals is not specifically associated with PSII. Thus, the fluorescence-based bioassay with the I-PAM offers a promising approach for the miniaturization and high-throughput testing of chemicals with aquatic macrophytes. For the chemical triclosan, however, the short-term effect prediction with the I-PAM has been shown to be less sensitive than with long-term bioassays, which might be due to physicochemical substance properties such as lipophilicity. Recommendations and Perspectives The results of this study show that the I-PAM represents a promising tool for decreasing the incubation times of aquatic macrophyte toxicity testing to about 24 h as a supplement to existing test batteries. The applicability of this I-PAM bioassay on emergent and submerged aquatic macrophyte species should be investigated in further studies. Regarding considerations that physicochemical properties of the tested substances might play an important role in microplate bioassays, the I-PAM bioassay should either be accompanied by evaluating physicochemical properties modeled from structural information prior to an experimental investigation, or by intensified chemical analyses to identify and determine nominal concentrations of the toxicants tested. The chemicals paraquat-dichloride, alizarine and triclosan were chosen as representatives for the toxicant groups of non-PSII herbicides, PAHs and PPCPs which are often detected in the aquatic environment. Nevertheless, in order to ensure a routinely applicable measuring device, experiments with a broader range of toxicants and samples of surface and/or waste waters are necessary. ESS-Submission Editor: Dr. Markus Hecker (MHecker@Entrix.com)     

Physicochemical substance properties as indicators for unreliable exposure in microplate-based bioassays

In the last years many efforts were made to transform standardized algal test protocols into low-cost microplate assays. While advantages were pointed out frequently, limitations are not systematically addressed, thus hindering a widespread utilisation. In this study a group of organic substances with a wide distribution of volatility (log K_AW from −6.53 to −2.13) and lipophilicity (log K_OW from 1.26 to 4.92) was investigated with respect to the influence of these physicochemical properties on their algal toxicity in different assays. Therefore the EC₅₀ values were determined with a microplate assay based on ISO 8692 protocol and the results were compared with those of an established algal growth inhibition test conducted in air tight glass vessels. Using the ratio of the EC₅₀ values, a clear connection between biological response and volatility as well as lipophilicity of test substances could be detected. Chemicals with a log K_OW higher than 3 or a Henry coefficient log K_AW higher than −4 were identified as less effective in the microplate assay than in the comparative assay. The loss in nominal concentration due to physicochemical properties could be shown to contribute to this using HPLC analysis. Consequently, when using microplate assay’s one should be aware that lipophilic and volatile chemicals might be underestimated in their toxicity, which could be indicated from evaluating related physicochemical properties modelled from structural information prior to an experimental investigation.     

Suborganismic and organismic effects of aldicarb and its metabolite aldicarb-sulfoxide to the zebrafish embryo (Danio rerio)

The new European chemical regulation (REACH) requires a short-term fish test for chemicals where the level of production exceeds 10tons per year. For ethical reasons (3R-concept), an alternative to the acute fish test should be introduced to decrease the number of animal testing with fish. The zebrafish embryo (Danio rerio) test became a valuable tool in ecotoxicology and already replaces the acute fish test for the evaluation of wastewater in Germany. Recent efforts are targeted to use this and other fish embryo tests for the effect assessment of chemicals. The toxic effects of the carbamate insecticide aldicarb and its metabolite aldicarb-sulfoxide to zebrafish embryos were analysed using two approaches with different endpoints. Organismic tests were conducted with zebrafish embryos exposed to the pesticides for 48h. In addition, suborganismic effects were examined analysing the enzyme inhibition of cholinesterases and carboxylesterases. On the organismic level, the only sublethal effect seen was the increase of heart rate at low and decrease at higher concentration with the use of aldicarb-sulfoxide but not with aldicarb (concentration range 0.2-300microM). In contrast, analysis of enzyme inhibitions showed high to very high effects caused by the two carbamates. The enzyme inhibition analysis of whole homogenates of exposed embryos may be advantageous for toxicant screening (biomarker of exposure) and might be used to bridge the gap of sensitivity of the (48h old) zebrafish embryos to adult fish when exposed to anti-cholinesterase substances (biomarker of prospective effect).     

Metals, non-metals and PCB in electrical and electronic waste--actual levels in Switzerland

The chemical composition of waste of small electrical and electronic equipment (s-WEEE), a rapidly growing waste stream, was determined for selected metals (Cu, Sb, Hg etc.) and non-metals (Cl, Br, P) and PCBs. During a 3-day experiment, all output products and the s-WEEE input mass flows in a WEEE recycling plant were measured. Only output products were sampled and analyzed. Material balances were established, applying substance flow analysis (SFA). Transfer coefficients for the selected substances were also determined. The results demonstrate the capability of SFA to determine the composition of the highly heterogeneous WEEE for most substances with rather low uncertainty (2 sigma +/- 30%). The results confirm the growing importance of s-WEEE regarding secondary resource metals and potential toxic substances. Nowadays, the thirty times smaller s-WEEE turns over larger flows for many substances, compared to municipal solid waste. Transfer coefficient results serve to evaluate the separation efficiency of the recycling process and confirm--with the exception of PCB and Hg--the limitation of hand-sorting and mechanical processing to separate pollutants (Cd, Pb, etc.) out of reusable fractions. Regularly applied SFA would serve to assess the efficacy of legislative, organizational and technical measures on the WEEE.     

气候变化与紫外线B辐射对北极苔原和极地荒漠生态系统的影响重要发现和扩展总结

引言 北极已成为对当前气候波动和预计的全球变暖增强的影响进行评估的重要地区.原因有以下几个方面:①在过去几十年中北极经历了大幅度的变暖过程(温度平均升高3℃,而在许多地区温度升高了4～5℃);②气候预测表明气候呈现持续变暖趋势,在2080年之前年平均气温升高4～5℃;③近期的气候变暖正在影响北极的环境和经济,这些影响还会加大,并对生活方式、文化及生态系统造成影响;④北极的变化可能会影响到地球上的其它地区.