黄海麻坑群沉积物磷的保存与转化及环境效应

基于对北黄海典型麻坑群海域某单位麻坑内部和外缘沉积物中不同赋存形态的磷、甲烷（CH₄）和硫化物等参数的分析,探讨了麻坑独特的环境中磷的转化与埋藏机制、沉积物-水体系磷的释放及对区域磷循环的影响.研究表明,沉积物中碎屑态磷（Det-P）是磷主要的赋存形态（>50%）,其次是有机磷（Org-P）、铁结合态磷（Fe-P）和自生态磷（Auth-P）,交换态磷（Exch-P）对总磷的贡献较小;麻坑内部与麻坑外缘处沉积物中溶解态活性磷（DRP）向水体的释放通量分别为2.84μmol/（cm²·a）和1.03μmol/（cm²·a）,对上层水体的贡献依次为19.6%和3.03%,是上层水体磷的重要来源.麻坑内外磷的埋藏速率与转化过程存在不同;研究区地下水的渗漏是磷的沉积速率和释放通量都普遍高的原因.北黄海麻坑区沉积物中磷的保存与转化还与浅层CH₄的逸出相关,潜在提高黄铁矿的生成速率.较高的沉积物-水界面磷通量必然对区域富营养化等生态环境问题产生深远影响,值得关注.     

粗放型绿色屋顶基质层对降雨出流水质影响

为研究粗放型绿色屋顶基质层对雨水出流N、P、COD和SS淋失的影响,根据华中地区降雨强度和水质实际情况,构建了3种不同基材配方的绿色屋顶基质层,在9场模拟暴雨下进行绿色屋顶的基质出流水质监测。结果表明:本试验各绿色屋顶设施对TN、NH₄+-N、NO₃--N和SS都有较好的削减作用,但对TP和PO₄3--P淋失现象明显,绿色屋顶的出流中以颗粒态P和溶解态N为主;去除出流中SS,对净化COD效果显著;生物炭的添加对出流污染物有明显的控制作用,能有效缓解降雨初期污染物浓度高的问题,同时能显著增加植物地上部生物量;厚度为5 cm的绿色屋顶出流水中N和COD较10 cm厚度低,但其SS出流平均浓度偏高,且植物后期不能维持良好的长势。粗放型绿色屋顶设施运行稳定后截污效应良好,具有较高的可行性和广阔的应用前景。     

新型厌氧多级喷动床及其厌氧氨氧化脱氮性能分析

为改善厌氧反应器内的流态,加快污泥的颗粒化和形成具有生态梯度的微生物生态系统,设计并制作了新型厌氧多级喷动床,实验测试了反应器的水力喷动、气体喷涌和污泥分层分级现象。在常温下,利用新型厌氧多级喷动床接种混合污泥,经过42 d的培养,成功启动厌氧氨氧化反应器,稳定运行18 d后,NH₄+-N、NO₂--N去除率均达到90%以上。启动60 d后,反应器底部出现大量粒径2 mm左右的颗粒污泥,且污泥具有良好的稳定性和沉降性能,沉降速度达到70 m/h。结果表明:厌氧多级喷动床因其特殊的水力结构,可有效加快污泥的颗粒化。     

二乙烯三胺五甲叉膦酸酸解磷尾矿的实验探究

为减少磷尾矿堆积带来的环境污染问题,实现磷尾矿的钙、镁、磷元素的分离,以高镁磷尾矿为原料,采用二乙烯三胺五甲叉膦酸(DTPMP)进行酸解,探究磷尾矿中主要物相在DTPMP中的分解机制,并通过单因素实验探究pH、反应时间、反应温度及投料比对磷尾矿中MgO、CaO和P_2O_5分解率的影响。实验结果表明:pH对P_2O_5的分解率影响较大,高温更有利于尾矿中镁的溶出,在pH为2. 5,反应时间为60 min,反应温度为80℃,投料比为1. 56时,MgO、CaO和P_2O_5的分解率分别达到61. 05%、38. 23%和9. 67%。     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Synergistic effects of Cu species and acidity of Cu-ZSM-5 on catalytic performance for selective catalytic oxidation of n-butylamine

In this work, a series of Cu-ZSM-5 catalysts with different SiO₂/Al₂O₃ ratios (25, 50, 100 and 200) were synthesized and investigated in n-butylamine catalytic degradation. The n-butylamine can be completely catalytic degradation at 350°C over all Cu-ZSM-5 catalysts. Moreover, Cu-ZSM-5 (25) exhibited the highest selectivity to N₂, exceeding 90% at 350°C. These samples were investigated in detail by several characterizations to illuminate the dependence of the catalytic performance on redox properties, Cu species, and acidity. The characterization results proved that the redox properties and chemisorption oxygen primarily affect n-butylamine conversion. N₂ selectivity was impacted by the Brønsted acidity and the isolated Cu²⁺ species. Meanwhile, the surface acid sites over Cu-ZSM-5 catalysts could influence the formation of Cu species. Furthermore, in situ diffuse reflectance infrared Fourier transform spectra was adopted to explore the reaction mechanism. The Cu-ZSM-5 catalysts are the most prospective catalysts for nitrogen-containing volatile organic compounds removal, and the results in this study could provide new insights into catalysts design for VOC catalytic oxidation.     

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.     

Analytical methods and environmental processes of nanoplastics

The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.     

废塑料再生过程废水中微塑料去除模拟试验

微塑料是一种存在于不同环境介质中的新兴污染物,主要来源于废弃塑料制品,其存在污染范围广、潜在环境污染大的问题.废塑料再生企业生产废水中微塑料浓度远高于其他类型废水,对其生产废水中的微塑料进行处理具有重要的环境意义.模拟废塑料再生过程的生产废水并进行微塑料去除的絮凝沉淀试验,研究絮凝剂投加量、pH、水力快速搅拌条件的单因素和正交试验对废水中微塑料去除率及其各因素作用的影响.结果表明:①当PAC (聚合氯化铝)投加量为10 mL,PAM (聚丙烯酰胺)投加量为7 mL,pH为9,水力快速搅拌条件为100 r/min下维持40 s再200 r/min下维持40 s时,微塑料的总去除率最高,达91%.②PAC投加量是影响微塑料去除效果的主要因素,其次是pH.③微塑料的去除率与其本身的密度有关,密度大的ABS (acrylonitrile butadiene styrene,丙烯腈-丁二烯-苯乙烯)去除率最高,密度小的PE (polyethylene,聚乙烯)去除率最低.④不同粒径区间的微塑料去除率区别较大,粒径小(0.1~0.25 mm)的微塑料去除效果最好.研究显示,通过控制PAC和PAM的投加量、pH和水力搅拌速率等条件,能够有效将废水中的微塑料通过絮凝沉淀的方法去除,从而达到净化含微塑料生产废水的目的.      

基于底栖动物的松花江流域不同地形分区水质指标阈值研究

为全面了解松花江流域不同地形分区内底栖动物群落对水质指标的响应规律,识别不同分区水质指标指示物种的差异,于2016—2018年对松花江流域97个采样点的水质指标〔EC、ρ（DO）、ρ（COD_Mn）、ρ（NH₃-N）、ρ（TN）、ρ（TP）〕和大型底栖动物群落进行调查分析,采用临界指示物种分析法（threshold indicator taxa analysis,TITAN）分别探讨松花江流域山区、丘陵区和平原区水质指标的生态阈值,当污染物浓度超过负响应阈值时敏感种密度降低,当超过正响应阈值时耐受种也会受到明显影响,底栖动物群落结构会发生显著变化.将TITAN法所得的负响应阈值作为触发底栖动物群落发生变化的最低值,正响应阈值为底栖动物群落的耐受极限值.结果表明:①松花江流域水质指标在不同地形分区内的阈值不同,除ρ（DO）和ρ（COD_Mn）外,其他指标负响应阈值均表现为山区 < 丘陵区 < 平原区,ρ（DO）则表现相反,ρ（COD_Mn）在丘陵区出现最高阈值（5.46 mg/L）、山区出现最低阈值（4.01 mg/L）.除ρ（DO）以外,其他指标的正响应阈值均呈山区 < 丘陵区 < 平原区的趋势,ρ（DO）正响应阈值的变化趋势则与之相反.②松花江流域内超过50%的采样点水质指标值均超过其负响应阈值,超出正响应阈值的采样点比例在6%~40%之间,说明流域受到一定的干扰,但干扰程度不严重.③同一物种在不同地形分区内对水体理化指标的指示方向可能相反.萝卜螺属在丘陵区为ρ（NH₃-N）的正响应指示物种,在平原区则转变为负响应指示物种;短沟蜷属在丘陵区为ρ（TN）和ρ（TP）的正响应物种,在平原区则转变为负响应物种.研究显示,大型底栖动物群落结构的分布特征是影响水质指标阈值指示物种识别的主要原因,而不同分区的自然地理状况、栖境状况和水质状况则是造成大型底栖动物群落结构分布差异的主要因素.