柴油车尾气微粒的燃烧性能

采用热解质量分析方法（TGA）对机动车柴油发动机尾气微粒（PM）的燃烧性能进行了研究。分别在空气和氮气条件下对柴油微粒的失重情况进行了测试。实验表明，柴油微粒的起始失重温度Tb为200℃左右，起始氧化温度Tox为410-450℃，最大失重温度Tmax为650℃-700℃，其可挥发组分（VOC）含量为48%-55%，增加氧气浓度仅在调温时对微粒燃烧有利。     

催化技术去除柴油机排放碳颗粒的研究进展

综述了柴油机排放碳颗粒催化燃烧中运用的贵金属催化剂、过渡金属催化剂、(类)钙钛矿催化剂以及催化技术与低温等离子体技术协同作用的最新研究进展,介绍了上述催化剂和催化技术的作用机理,并探讨了它们在实际应用中存在的问题和应用前景。     

柴油车尾气颗粒物排放现状评价

对2013年哈尔滨市不同供油方式的柴油车排气细颗粒物或黑碳测量参数—光吸收系数进行了统计分析,结果表明:涡轮增压和自然吸气供油方式光吸收系数均值分别为1.39 m-1和1.27 m-1,超标率分别为5.8%和2.4%,采用颗粒物控制措施及排气装置强制维护降低了颗粒物排放,符合排放标准。     

Modeling and predicting low-speed vehicle emissions as a function of driving kinematics

An instantaneous emission model was developed to model and predict the real driving emissions of the low-speed vehicles. The emission database used in the model was measured by using portable emission measurement system (PEMS) under actual traffic conditions in the rural area, and the characteristics of the emission data were determined in relation to the driving kinematics (speed and acceleration) of the low-speed vehicle. The input of the emission model is driving cycle, and the model requires instantaneous vehicle speed and acceleration levels as input variables and uses them to interpolate the pollutant emission rate maps to calculate the transient pollutant emission rates, which will be accumulated to calculate the total emissions released during the whole driving cycle. And the vehicle fuel consumption was determined through the carbon balance method. The model predicted the emissions and fuel consumption of an in-use low-speed vehicle type model, which agreed well with the measured data.     

含氮有机物深度氧化催化剂：PCN—1型性能的研究

考察了PCN—1型催化剂对N.N-二甲基甲酰胺(DMF)、正丁胺、环己胺,苯胺、硝基苯、丙酮、甲苯等有机物完全氧化的活性,检测了DMF、正丁胺在不同温度下氧化分解产生的NOx含量。实验结果表明,PCN—1型催化剂对DMF、正丁胺、丙酮的氧化活性较高,而且能抑制DMF、正丁胺氧化过程NOx的形成在空速5000～15000h~1,DMF、正丁胺浓度分别在3000～5000mg/m~3、2000～3000mg/m~3时,T_(98)≤300℃,在完全氧化温度以上,100℃以下时,NOx控制率≥90％该催化剂主要应用于含有机胺及酮类的工业废气的净化     

柴油机排出颗粒物致突变性研究

采用Ａｍｅｓ试验，检测６种国产和进口牌号柴油机排出颗粒物的诱变性，研究发现，６种柴油机排出颗粒物均呈阳性，其颗粒提取物和诱变性之间，存在剂量一反应关系。Ａｍｅｓ试验结果，主要引起ＴＡ９８－Ｓ９的回变菌落落数加，显示受试物中含有移码型直接致突物，试验还发现，国产和进口柴油机排出颗粒物的致突突变性，在怠速和加速工况下，其诱变活性有一定差异。     

重型柴油车污染物排放因子测量的影响因素

为了调查我国重型柴油车排放污染物的基本水平,确定CO、HC、NO_x和颗粒物等污染物的排放因子,利用满足国Ⅲ排放标准的重型柴油车,分别采用PEMS(portable emission measurement system,车载排放测试系统,由便携式SEMTECH-DS型气态污染物排放测量设备和DMM颗粒物排放测量设备组成)及满足法规排放测量要求的重型车整车底盘测功机方法,研究了不同负载(0%、50%、100%及120%)和2种测试工况对重型车排放因子测量的影响. 结果表明:过载(120%负载)下NO_x和颗粒物等排放因子均比零负载下高出近90%;在平均车速较低、怠速时间长的VECC工况下,气态污染物、颗粒物的排放因子比平均车速高、怠速时间短的C-WTVC工况高出30%左右;PEMS系统和重型车底盘测功机系统所测气态污染物排放因子的相关性较好,但DMM颗粒物排放测试设备与重型车整车底盘测功机所测的颗粒物排放因子相差可达50%左右.      

On-road pollutant emission and fuel consumption characteristics of buses in Beijing

On-road emission and fuel consumption (FC) levels for Euro III and IV buses fueled on diesel and compressed natural gas (CNG) were compared, and emission and FC characteristics of buses were analyzed based on approximately 28,700 groups of instantaneous data obtained in Beijing using a portable emissions measurement system (PEMS). The experimental results revealed that NOx and PM emissions from CNG buses were decreased by 72.0% and 82.3% respectively, compared with Euro IV diesel buses. Similarly, these emissions were reduced by 75.2% and 96.3% respectively, compared with Euro III diesel buses. In addition, CO2, CO, HC, NOx, PM emissions and FC of Euro IV diesel buses were reduced by 26.4%, 75.2%, 73.6%, 11.4%, 79.1%, and 26.0%, respectively, relative to Euro III diesel buses. The CO2, CO, HC, NOx, PM emissions and FC factors all decreased with bus speed increased, while increased as bus acceleration increased. At the same time, the emission/FC rates as well as the emission/FC factors exhibited a strong positive correlation with the vehicle specific power (VSP). They all were the lowest when VSP < 0, and then rapidly increased as VSP increased. Furthermore, both the emission/FC rates and emission/FC factors were the highest at accelerations, higher at cruise speeds, and the lowest at decelerations for non-idling buses. These results can provide a base reference to further estimate bus emission and FC inventories in Beijing.     

La-Na-Co-Mn-O系钙钛矿型催化剂同时去除柴油机碳颗粒和NO_x性能的研究

采用低温燃烧法制备了Na+部分取代La3+的La1-xNaxCo0.5Mn0.5O3系钙钛矿型复合氧化物催化剂。利用程序升温反应(TPR)技术,对催化剂应用于柴油机常规排放物中的碳微粒(soot)和氮氧化合物(NOx)的同时催化脱除性能进行了研究。     

低温等离子体治理柴油机尾气污染的研究进展

柴油发动机以其良好的燃油经济性和动力学特性得到广泛应用,但是其尾气排放中的氮氧化物有害气体和难以分解的微粒物含量较多,造成了严重环境污染。目前,研究开发中的柴油机尾气后处理技术,如还原催化转化、氧化催化转化和微粒捕集等,存在催化剂价格昂贵、催化活性低、有效温度范围小和捕集器保持清洁状态困难等不足。国内外大量的研究结果证明,基于气体放电的低温等离子体技术能有效降低柴油机尾气污染物排放,且无二次污染。本文通过低温等离子体的产生,柴油机尾气中的氮氧化物和微粒物的净化,综合介绍了低温等离子体净化柴油机尾气技术的研究进展,针对当前研究中存在的问题,论述了今后的发展趋势。     

Real-world gaseous emission characteristics of natural gas heavy-duty sanitation trucks

As compared to conventional diesel heavy-duty vehicles, natural gas vehicles have been proved to be more eco-friendly due to their lower production of greenhouse gas and pollutant emissions, which are causing enormous adverse effects on global warming and air pollution. However, natural gas vehicles were rarely studied before, especially through on-road measurements. In this study, a portable emission measurement system (PEMS) was employed to investigate the real-world emissions of nitrogen oxides (NOx) (nitrogen monoxide (NO), nitrogen dioxide (NO₂)), total hydrocarbons (THC), carbon monoxide (CO), and carbon dioxide (CO₂) from two liquified natural gas (LNG) China V heavy-duty cleaning sanitation trucks with different weight. Associated with the more aggressive driving behaviors, the vehicle with lower weight exhibited higher CO₂ (3%) but lower NOx (48.3%) (NO₂ (78.2%) and NO (29.4%)), CO (44.8%), and THC (3.7%) emission factors. Aggressive driving behaviors were also favorable to the production of THC, especially those in the medium-speed range but significantly negative to the production of CO and NO₂, especially those in the low-speed range with high engine load. In particular, the emission rate ratio of NO₂/NO decreased with the increase of speed/scaled tractive power in different speed ranges.     

柴油机尾气净化用的钙钛矿型催化剂的研究

用浸渍法制备了多种ABO_3型催化剂,考察了多种因素对其活性的影响及作用机制。柴油机台架实验结果表明,在A位掺杂Sr可提高催化剂的活性;稀土在最后一次浸渍液中浸渍,以二次浸渍为宜;堇青石陶瓷蜂窝状催化剂的性能优于γ-Al_2O_3球状催化剂。蜂窝状催化剂上CO的起燃温度T_(50)％=110℃,而T_(90)％=157℃;在温度仅为200℃,而空速高达70000h~(-1)的条件下CO的净化率仍达90％;积碳起燃温度为323℃,优于Pt族贵金属催化剂;热稳定性和对CO浓度的适应性较好,且具有抗SO_2中毒能力。     

吸入柴油机排出物对小鼠骨髓细胞微核出现率的影响

小鼠吸入过滤或未过滤的柴油机排出物，染毒８ｈ／ｄ，分别染毒２、５、８ｄ后，发现小鼠骨髓细胞微核率明显升高。吸入过滤后排出物的小鼠骨髓细胞微核出现率低于未过滤组。柴油机排出物对小鼠染色体有一定的损伤作用，过滤后的柴油机排出颗粒物中，致染色体损伤的物质减少，不同吸入时间（２、５、８ｄ）对小鼬骨髓细胞微核出现率，没有显著差异。     

催化湿式氧化技术中催化剂应用研究的新进展

催化湿式氧化技术是在高温高压条件下处理高浓度、有毒有害且难生物降解污染物的一种高级氧化技术。本文在检索了国内外大量参考文献的基础上,概述了催化湿式氧化技术的最新进展,总结了催化湿式氧化技术中催化剂的分类、组成、应用及失活现象,以期对有关研究者提供一定的参考。     

提高柴油质量减少汽车排气污染

柴油机车应用于道路运输具有许多优点，但环境保护要求减少排气污染、颗粒排放污染至关重要，为此，强化柴油燃料规格是其主要的驱动力。本文介绍了美国，西欧和亚太地区柴油质量现状和趋势，分析了我国柴油燃料质量及其改进意见。     

基于PEMS技术的交叉口尾气排放特性分析

利用车载尾气检测设备(PEMS)OEM-2100收集了在交叉口和路段上的实时尾气排放数据,利用GIS和相应二次开发工具构造了排放数据的分析平台,提出了交叉口尾气排放的空间分析方法,并对所收集的数据进行了对比分析。在此基础上,得到了交叉口处车辆各转向下的不同排放物的排放特征,计算了交叉口各转向相对于路段的排放系数,并对PEMS技术交叉口尾气排放进行了探讨。     

柴油机污染物排放后处理技术的研究进展

国内外柴油机主要排放物NOx和微粒的后处理技术的研究现状和最新技术发展动态表明，机内、机外处理技术的组合，是达到未来柴油机排放标准、实现大幅度降低柴油机污染物排放的趋势。分析了各种机外净化技术的特点和存在问题，阐述了燃油含硫量对柴油机排放后处理的影响。     

Raman spectroscopy of diesel and gasoline engine-out soot using different laser power

We studied engine-out soot samples collected from a heavy-duty direct-injection diesel engine and port-fuel injection gasoline spark-ignition engine. The two types of soot samples were characterized using Raman spectroscopy with different laser powers. A Matlab program using least-square-method with trust-region-reflective algorithm was developed for curve fitting. A DOE (design of experiments) method was used to avoid local convergence. The method was used for two-band fitting and three-band fitting. The fitting results were used to determine the intensity ratio of D (for “Defect” or “Disorder”) and G (for “Graphite”) Raman bands. It is found that high laser power may cause oxidation of soot sample, which gives higher D/G intensity ratio. Diesel soot has consistently higher amorphous/graphitic carbon ratio, and thus higher oxidation reactivity, compared to gasoline soot, which is reflected by the higher D/G intensity ratio in Raman spectra measured under the same laser power.     

Experimental investigation into the oxidation reactivity, morphology and graphitization of soot particles from diesel/n-octanol mixtures

Aiming to investigate the impacts of n-octanol addition on the oxidation reactivity, morphology and graphitization of diesel exhaust particles, soot samples were collected from a four-cylinder turbocharged diesel engine fueled with D100（neat diesel fuel）, DO15（85% diesel and 15% n-octanol, V/V） and DO30（70% diesel and 30% n-octanol, V/V）. All tests were conducted at two engine speeds of 1370 and 2150 r/min under a fixed torque of 125 N ·m. The soot properties were characterized by thermogravimet...     

国Ⅰ～国Ⅲ重型柴油车尾气PM_(2.5)及其碳质组分的排放特征

机动车排放是大气PM2.5污染的主要来源之一,而在机动车排放的PM2.5中,约80%以上来自重型柴油车.为了研究重型柴油车尾气PM2.5及其碳质组分的排放特征,本研究基于车载排放测试系统(PEMS),对7辆不同排放阶段的重型柴油车进行了尾气PM2.5采样分析,并进一步分析了PM2.5中的OC和EC组分.结果显示,从国Ⅰ到国Ⅲ阶段,重型柴油车PM2.5排放因子分别为(0.466±0.300)g·km-1、(0.112±0.025)g·km-1和(0.056±0.034)g·km-1,表明随着排放标准的加严,测试车辆的尾气PM2.5排放因子呈现显著的下降趋势.行驶工况对重型柴油车尾气PM2.5及其碳质组分排放存在较大影响,PM2.5排放因子在高速和市区工况下相对较高,而在市郊工况下则较低;OC和EC的比值在市区工况下为(2.86±1.07)∶1,而在市郊和高速工况下为(0.97±0.49)∶1.