用氟化钾水溶液从制药废液中回收吡啶

研究了普通精馏与加盐分相技术在回收吡啶中的应用。测定了吡啶 水 氟化钾体系在25℃时的液液相平衡数据,采用Pitzer理论和UNIQUAC方程对相平衡数据进行了理论计算,结果表明计算值与实验值符合良好。采用氟化钾水溶液回收吡啶,当60%氟化钾浓溶液与50%吡啶/50%水的物料的质量比为2.0时,有机相中吡啶的纯度可达到92.60%(质量分数),水相中氟化钾稀溶液经蒸发回收后循环使用不影响分离性能。该工艺的开发成功为制药行业从制药废液中回收吡啶开辟了一条新途径。     

蚀刻液水合肼还原除铜

将电路板厂废弃的蚀刻液,经氢氧化铜沉淀法回收大部分铜后,再采用水合肼还原,进一步除铜。反应温度为50℃,水合肼质量分数为3．0％,溶液pH为6．0,废液中铜的去除率可达98.5％,处理后废液中铜的质量浓度低于0．2g／L,可作为碱性蚀刻液重复利用。     

采用络合萃取法从维生素B12发酵废液中回收丙酸

采用络合萃取法回收维生素B12发酵废液中的丙酸,确定了络合萃取的最佳工艺条件：以0．5mol／L的磷酸三丁酯(TBP)为络合剂,油水比(体积比)为1：2,常温下萃取30min。在最佳工艺条件下单级萃取率为56％左右,四级萃取率可达98％以上。络合萃取过程中使用的有机溶剂可反复使用,使成本大大降低。     

均匀设计法优化造纸黑液的湿式氧化法处理工艺

通过均匀设计实验,对造纸黑液进行湿式氧化处理,数据回归得到CODCr、吸光度、浊度的回归方程,各回归方程显著,氧分压对造纸黑液各指标影响最大;研究反应过程中反应温度、氧分压、进水pH值、进水浓度、搅拌强度、反应时间对造纸黑液湿式氧化(WAO)处理的影响,6因素优化的操作条件依次为:180℃、3.0MPa、7.25、5500mg/L、500r/min、60min;在优化的操作条件下,造纸黑液的CODCr、CODCr去除率为1661mg/L、69.8%,吸光度、脱色率为0.63、96.3%,浊度、浊度去除率为661NTU、74.8%.均匀设计法在造纸黑液WAO处理中得到了较好的应用.     

Fermentative hydrogen production from beet sugar factory wastewater treatment in a continuous stirred tank reactor using anaerobic mixed consortia

A low pH, ethanol-type fermentation process was evaluated for wastewater treatment and bio-hydrogen production from acidic beet sugar factory wastewater in a continuous stirred tank reactor (CSTR) with an effective volume of 9.6 L by anaerobic mixed cultures in this present study. After inoculating with aerobic activated sludge and operating at organic loading rate (OLR) of 12 kgCOD?m^-3·d^-1, HRT of 8h, and temperature of 35°C for 28 days, the CSTR achieved stable ethanol-type fermentation. When OLR was further increased to 18 kgCOD?m^-3·d^-1 on the 53rd day, ethanol-type fermentation dominant microflora was enhanced. The liquid fermentation products, including volatile fatty acids (VFAs) and ethanol, stabilized at 1493 mg·L^-1 in the bioreactor. Effluent pH, oxidation-reduction potential (ORP), and alkalinity ranged at 4.1–4.5, -250–(-290) mV, and 230–260 mgCaCO₃?L^-1. The specific hydrogen production rate of anaerobic activated sludge was 0.1 L?gMLVSS^-1·d^-1 and the COD removal efficiency was 45%. The experimental results showed that the CSTR system had good operation stability and microbial activity, which led to high substrate conversion rate and hydrogen production ability.     

草浆造纸黑液无污染排放治理新方案——双极膜电渗析法回收碱

介绍碱法草浆黑液采用膜技术处理的各种方案,着重介绍了碱法草浆黑液资源化全回收技术并提出了新的技术方案,该方案是先用硫酸中和酸析黑液中的木质素,或用纳滤方案回收木质素,然后采用双极膜电渗析法回收已去除木质素的黑液中的酸和碱,最后经蒸发和喷雾干燥回收其中的糖、其他营养成分及大部分水,达到无污染排放的目的。该方案碱回收率在50%～80%,取决于黑液中碱的浓度,回收1 t碱的耗电量低于2 500 kW.h。该法的基本投资比同规模碱回收法节省60%以上,具有较好的经济效益。     

苇浆造纸黑液的Fenton预处理研究

采用Fenton试剂预处理高浓度苇浆造纸黑液,经正交设计得出各因素对黑液COD去除率的影响顺序为:pH＞[H2O2]＞[Fe2 ]＞反应时间.确定最佳操作条件为:初始pH=4、[H2O2]=0.088 mol/L、[Fe2 ]=14.39 mmol/L、反应40 min,此条件下废水COD去除率可达80%以上,色度及浊度去除率达96%.动力学表明:Fenton试剂预处理高浓度苇浆造纸黑液的表观过程近似符合一级反应规律.废水经处理后可生化性指标BOD/COD平均从0.303升高到0.558.     

将混凝技术应用于大规模污水处理

介绍采用混凝技术大规模处理运河污水时所遇到的一些问题,以及一些生产经验,提出在设施、设备及工艺方面的相应解决办法。强调设备维护、员工技能和管理机制在生产中的重要性,提出科学地进行设备日常维护的方法。通过小试验,提出对东莞运河水污染治理的一点设想,并解释工程中混凝反应需要足够搅拌力度的问题。     

中型针织面料印染厂废水处理研究

针对中型针织面料印染厂含有机污染物浓度较高的废水,设计了一套废水处理工艺流程,并通过实例对其进行了检验。废水水质CODcr为1 200 mg/L、BOD5为400 mg/L、SS为280 mg/L、色度为400倍、处理水量1 000 m^3/d,在经过水解、生物接触氧化和沉淀等工艺处理后,出水指标稳定,并且达到了环保部门的排放要求。     

Studies on solvent extraction of iron(III) as a step for conversion of a waste effluent to a value added product

Solvent extraction of iron(III) from actual sulphate waste pickle liquor was investigated using trialkylphosphine oxide diluted with kerosene. The waste pickle liquor was procured from a local company which deals with the manufacturing of pipes and tubes made of iron and steel. Various parameters were studied to optimise a suitable condition for the maximum extraction of iron. The composition of the aqueous feed used in the experiment was 60.88 g/L Fe(III), 53 g/L acid with traces of Cu, Ni and Co. An ambient extraction at 30 °C yielded acceptable kinetics and loading efficiency for 40% trialkylphosphine oxide with a saturated loading capacity of 51.85 g/L in four contacts at O/A ratio of 1/1 in a multiple contact mode. Iron from the loaded organic was stripped using various strippants such as distilled water, H₂SO₄ and oxalic acid. Since only 32% of loaded Fe could be stripped with 2 M H₂SO₄ in five contacts, further stripping was done with 5% oxalic acid which showed a very promising result. It was found that almost 100% of Fe(III) could be stripped out with 5% oxalic acid at O/A of 1/1 in five contacts.