某基岩区工业固体废物填埋场地递进式场地环境调查实例

针对某基岩区简易封场后的固体废物填埋场,采用多层次、递进式调查策略,配合使用地球物理探测、直压式土壤快速取样、现场快速检测等技术,分3个阶段开展填埋场及其周边环境调查。第1阶段,调查地质环境特征,开展地球物理探测;第2阶段,调查填埋物、渗滤液主要组分及对周边积水、农田土壤、民用井水的污染情况;第3阶段,划定重点污染区域,开展土壤和地下水污染调查。调查结果显示,填埋区已发生明显渗漏,对邻近区域土壤、地下水及地表积水造成了一定污染,但未对周边农用地土壤、民用井水质等产生不利影响,总体处于可控范围。提出,通过削减污染源,切断污染物迁移、暴露途径,消除已有污染影响,长期跟踪监测等多项管控治理措施进行综合整治。     

金属冶炼进口物料的固体废物鉴别方法

建立了金属冶炼进口物料的固体废物鉴别方法,并利用该方法对海关查扣的3种金属冶炼进口物料进行了固体废物鉴别。鉴别结果显示:物料1、2和3的自然属性分别为砷含量超标铜精矿、锰阳极泥、回转窑氧化锌,产生来源分别为有害物质超标的产品、污染控制设施产生的物质、有意识加工的目标产物;物料1和2属于我国禁止进口的固体废物,物料3不属于固体废物。本文建立的固体废物鉴别方法可行,可为金属冶炼进口物料的固体废物鉴别和监管提供参考。     

Synthesis of branched,nano channeled,ultrafine and nano carbon tubes from PET wastes using the arc discharge method

Upcycling polymer wastes into useful, and valuable carbon based materials, is a challenging process. We report a novel catalyst-free and solvent-free technique for the formation of nano channeled ultrafine carbon tubes (NCUFCTs) and multiwalled carbon nanotubes (MWCNTs) from polyethylene terephthalate (PET) wastes, using rotating cathode arc discharge technique. The soot obtain from the anode contains ultrafine and nano-sized solid carbon spheres (SCS) with a mean diameter of 221 nm and 100 nm, respectively, formed at the lower temperature region of the anode where the temperature is approximately 1700 °C. The carbon spheres are converted into long “Y” type branched and non-branched NCUFCTs and MWCNTs at higher temperature regions where the temperature is approximately 2600 °C, with mean diameters of 364 nm and 95 nm, respectively. Soot deposited on the cathode is composed of MWCNTs with a mean diameter of 20 nm and other nanoparticles. The tubular structures present in the anode are longer, bent and often coiled with lesser graphitization compared to the nanotubes in the soot on the cathode.     

模拟阳光下Ag／I-TiO2光催化预处理山核桃加工废水

研究了在模拟太阳光下，采用银修饰的碘掺杂二氧化钛光催化剂（Ag／I—TiO2）对某食品厂山核桃加工废水进行光催化预处理的效果。结合x射线衍射（XRD）、比表面积分析（BET）、紫外-可见漫反射光谱（uV—Vis）的表征结果，来分析催化剂结构对于废水处理效果的影响。探讨了Ag含量、废水初始pH（pHi）和光照时间等因素对化学需氧量（COD）去除及水质可生化性（B／C）提高的影响。并得出适宜的反应参数为：3％Ag含量；pHi为6；光照时间为240min。在最佳条件下，COD去除率45％，废水B／C比由0．17上升到0．31。光催化氧化法能够有效降低山核桃加工废水的COD含量，并达到显著提高废水可生化性的目的。     

典型钢铁企业汞排放水平及排放特征研究

以某典型钢铁企业为研究对象,测定企业废气、废水、固废汞排放水平,并分析汞排放特征。研究表明,球团、烧结、高炉工艺废气排口烟尘中汞排放浓度和排放速率明显低于烟气;汞主要以气态形式排放,烧结工艺排口废气汞最高浓度分别是其他2个排口的7倍和3倍。球团、烧结、高炉、电炉四工艺环节中,烧结汞排放速率占四工艺汞排放速率总和的87%。半干法脱硫、氨法脱硫、石灰石石膏脱硫对废气中汞的去除效率分别为90.0%、78.7%和29.9%。企业废水排放未检出汞,脱硫产生固废汞含量明显高于除尘产生固废汞含量,脱硫灰汞含量是脱硫石膏的15倍。     

Full-scale blending treatment of fresh MSWI leachate with municipal wastewater in a wastewater treatment plant

Fresh leachate, generated in municipal solid waste incineration (MSWI) plants, contains various pollutants with extremely high strength organics, which usually requires expensive and complex treatment processes. This study investigated the feasibility of blending treatment of MSWI leachate with municipal wastewater. Fresh MSWI leachate was pretreated by coagulation–flocculation with FeCl₃ 2 g/L and CaO 25 g/L, plate-and-frame filter press, followed by ammonia stripping at pH above 12. After that, blending treatment was carried out in a full-scale municipal wastewater treatment plant (WWTP) for approximately 3 months. Different operational modes consisting of different pretreated leachate and methanol addition levels were tested, and their performances were evaluated. Results showed that throughout the experimental period, monitored parameters in the WWTP effluent, including COD (<60 mg/L), BOD₅ (<20 mg/L), ammonium (<8 mg/L), phosphorus (<1.5 mg/L) and heavy metals, generally complied with the Chinese sewage discharged standard. Under the experimental conditions, a certain amount of methanol was needed to fulfill TN removal. An estimation of the operation cost revealed that the expenditure of blending treatment was much lower than the total costs of respective treatment of MSWI leachate and municipal wastewater. The outcomes indicated that blending treatment could not only improve the treatability of the MSWI leachate, but also reduce the treatment cost of the two different wastewaters.     

TiO2-Cu2O/蒙脱土复合光催化剂的制备与性能

以钠基蒙脱土（MMT）为载体，先采用溶胶-凝胶法将纳米TiO₂引入到MMT层间，再采用化学沉积法将纳米Cu₂O负载在TiO₂/MMT上，制备出TiO₂-Cu₂O/MMT纳米复合光催化剂。采用XRD、SEM、紫外-可见漫反射技术对催化剂进行了表征。以甲基橙为目标污染物，考察了催化剂的光催化性能。表征结果显示：TiO₂与Cu₂O均匀分布在MMT的表面与片层孔隙中;TiO₂-Cu₂O/MMT结合了TiO₂和Cu₂O的特性，拓宽了催化剂的光吸收范围。实验结果表明，在光源为可见光、初始甲基橙质量浓度为20 mg/L、光催化剂加入量为2 g/L的条件下，TiO₂-Cu₂O/MMT纳米复合光催化剂对甲基橙的光催化降解效果明显优于单一负载的Cu₂O/MMT和TiO₂/MMT，大幅提高了催化剂的光催化效率，反应300 min时TiO₂-Cu₂O/MMT对甲基橙溶液的脱色率达到93%。     

Multi-criteria evaluation technique for SFI site identification of NORMS and oil industry waste disposal – Possibilities in Kuwait

Waste generation and accumulating quantities of oil field waste are a matter of environmental concern. This study proposes the Slurry Fracture Injection (SFI) technique as an alternative waste disposal method. The slurried solids injection waste disposal method is environmentally secure and permanent, leaving no future liabilities that must be risk-evaluated or priced. An entire waste stream comprising ground solids and waste water can be injected into deep and hydraulically secure target strata with no contamination of potable water-bearing formations or formations outside the target zone that may contain resources (gas and oil). The slurry injection method can be used to clean and reclaim landfills, oil pits and granular waste dumps. This article proposes a two-tier screening method for evaluating the feasibility of this technique and the identification of suitable target zones. A stringent environmental and process control monitoring program should complement the planning and operational period to ensure environmental protection, waste containment, and regulatory HSE compliance.     

ZnO/LixNi1-xO光催化降解甲基橙的研究

采用溶胶凝胶法制备LixNi1-xO和ZnO粉体,利用球磨法制备ZnO/LixNi1-xO复合粉体,以紫外光为光源,通过降解甲基橙,研究了锂掺杂及n-p复合对氧化镍的光催化性能影响。结果表明：当投放量为0.1 g/L,x≤0.075（摩尔分数）的锂掺杂氧化镍均比未掺杂氧化镍的光催化活性高。当锂掺杂摩尔分数为0.025,投放量为0.4 g/L时锂掺杂氧化镍的光催化活性最佳,甲基橙最高降解率达到93.1%。当ZnO/Li0.025Ni0.975O在质量比为1∶1,投放量为0.2 g/L时光催化活性最佳,甲基橙最高降解率达到98.1%。     

制革废水和印染废水的综合毒性评估及鉴别

研究采用成组生物毒性试验(发光菌急性毒性、斑马鱼幼鱼急性毒性,斑马鱼胚胎发育毒性和小球藻急性毒性),结合理化指标,通过毒性单位、平均毒性(average toxicity,Av Tx)、毒性指数(toxic print,Tx Pr)、最敏感的测试(most sensitive test,MST)和潜在毒性效应指数(potential ecotoxic effects probe,PEEP)对不同工艺阶段印染及制革废水进行毒性削减评估.结果表明PEEP能兼顾废水排放量与毒性效应,更为客观地表征了废水综合毒性,PEEP评价结果显示制革废水和印染废水的毒性削减率分别达到36.8%和23.2%.最后,以发光菌作为受试生物,采用毒性鉴别评估(toxicity identification evaluation,TIE)技术,对印染废水进行毒性鉴别.结果表明,印染废水中主要的致毒物质为非极性有机污染,其次为可滤性化合物,然后是重金属、氧化性物质以及挥发性物质.