内压式中空纤维超滤膜污染模型研究

以流体力学和过滤理论为基础,建立了一个描述内压式中空纤维超滤膜污染的数学模型。该模型将膜的性质、原水的性质、清洗条件等多种因素对超滤过程的影响,用一个参数——膜堵塞系数表示。实验以造纸黒液稀释水为原水,对模型参数进行了拟合、验证,模拟计算结果与实验实测数据比较吻合,说明该模型能较好的模拟内压式中空纤维超滤膜过滤过程。     

一体式膜生物反应器处理生活污水的研究

研究了一体式膜生物反应器对生活污水的处理效果。实验结果表明,膜生物反应器对COD、TOC、NH4+-N、TN、TP的平均去除率为93.4%、96.2%、97.2%、63.8%、60.6%,并且污泥活性随着运行时间的延长而有所降低。     

pH值调节对红霉素膜浆中抗生素的降解作用

利用微生物法对红霉素膜浆中的红霉素药物残留量进行测定,红霉素残留量为265．88μg／mL。再通过调节pH值不同对膜浆残留红霉素的降解进一步研究。利用盐酸将膜浆的pH值调到2时,残留红霉素浓度为15．03μg／mL;降解率为94．35％。     

纤维乙醇黑液处理

采用微电解＋厌氧折流板反应器（ABR）＋上流式厌氧污泥床（UASB）＋膜生物反应器（MBR）组合工艺对纤维乙醇黑液进行处理。结果表明：当黑液中COD质量浓度在12000mg／L左右,该组合工艺中厌氧停留时间（HRT）为48h时,厌氧COD去除率达到72％,MBR中的HRT为20h时,COD的去除率在80．8％～87．5％之间,出水COD质量浓度稳定在301～537mg／L．且MBR抗冲击负荷能力较强。     

生物表面活性剂强化植物修复重金属污染土壤的可行性

利用有机配体强化植物修复重金属污染土壤是提高植物修复效果的常用措施．但大部分有机配体会引起二次污染而限制了其在土壤重金属修复中的应用。如果能将生物表面活性剂强化植物修复不仅会弥补这一不足．而且还能降低费用。生物表面活性剂在重金属污染土壤修复中的应用以及生物表面活性剂去除重金属的机理表明,将其强化植物修复是完全可行的,并且可以增加植物细胞膜透性,更好地促进植物对重金属的吸收。     

水膜预湿行为对典型保温材料燃烧抑制实验研究*

为探索喷淋形成水膜的预湿行为对外立面典型保温材料燃烧抑制机理,采用自建水膜预湿抑制保温材料燃烧实验装置,研究外加辐射作用下,水膜流率对聚苯乙烯（PS）保温材料表面出现干斑、变形和熔融的影响规律。结果表明:实验结束时PS材料表面水膜出现干斑、材料发生变形和熔融面积占比均与无量纲辐射强度呈正相关;PS材料表面水膜出现干斑、材料发生变形和熔融的时间随着无量纲辐射强度增大呈先变小后稳定的趋势;实验条件下,PS材料表面水膜出现干斑、材料发生变形和熔融的临界无量纲辐射强度分别为0.002 0,0.002 6,0.003 3。水膜预湿行为会很大程度阻止保温材料的熔融热解燃烧,为灭火救援提供一定的理论参考。     

平板膜生物反应器临界通量测定方法研究

临界通量在膜污染控制中是一个非常重要的概念.本文采用通量阶梯式递增法测定平板膜生物反应器的临界通量,在此基础上考察了不同测定参数对临界通量的影响.结果表明,测定临界通量过程中,当初始启动通量小于临界通量时,其对临界通量的测定值影响不大;当通量阶梯递增量增大时,临界通量的测定结果变小;当测定间隔时间段变长时,临界通量的测定结果相应变小.在测定临界通量时,推荐以下测定参数:通量阶梯递增量不大于4 L/(m2·h),测定间隔时间段取15～30 min;初始启动通量的选择要适宜,太大可能导致试验结果的误差.     

Di（2-ethylhexyl）phosphoric acid-coconut oil supported liquid membrane for the separation of copper ions from copper plating wastewater

Permeation of Cu(II) from its aqueous solution through a supported liquid membrane (SLM) containing di(2-ethylhexyl)phosphoric acid (D2EHPA) carrier dissolved in coconut oil has been studied. The effects of Cu(II), pH (in feed), H2SO4 (stripping) and D2EHPA (in membrane) concentrations have been investigated. The stability of the D2EHPA-coconutoil has also been evaluated. High Cu(II) concentration in the feed leads to an increase in flux from 4.1 × 10-9 to 8.9 × 10-9 mol/(m2·s) within the Cu(II) concentration range 7.8×10-4-78.6×10-4 mol/L at pH of 4.0 in the feed and 12.4 × 10-4 mol/L D2EHPA in the membrane phase. Increase in H2SO4 concentration in strip solution leads to an increase in copper ions flux up to 0.25 mol/L H2SO4, providing a maximum flux of 7.4 × 10-9 mol/(m2·s). The optimum conditions for Cu(II) transport are, pH of feed 4.0, 0.25 mol/L H2SO4 in strip phase and 12.4 × 10-4 mol/L D2EHPA (membrane) in 0.5 (m pore size polytetrafluoroethylene (PTFE) membrane. It has been observed that Cu(II) flux across the membrane tends to increase with the concentration of copper ions. Application of the method developed to copper plating bath rinse solutions has been found to be successful in the recovery of Cu(II). rane. It     

Improvement of antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes(PPMMs). Attenuated total reflection-Fourier transform infrared spectroscopy(ATR/FT-IR)and field emission scanning electron microscope(FE- SEM)were used to characterize the chemical and morphological changes on the membrane surfaces.Water contact angles and relative pure water fluxes were measured.The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes.To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor(MBR),filtration for active sludge was performed using synthetic wastewater.With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d,the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.     

Performances of biological aerated filter employing hollow fiber membrane segments of surface-improved poly （sulfone） as biofilm carriers

Using the surface of poly （sulfone） hollow fiber membrane segments as grafted layer, the hydrophilic acrylamide chain was grafted on by UV-photoinduced grafting polymerization. The gained improvement of surface wettability for the modified membrane was tested by measuring the contact-angle as well as FTIR spectra. Then correlation between the hydrophilic ability of support material and the biofilm adherence ability was demonstrated by comparing the pollutant removal rates from urban wastewater via two identical lab-scale up-flow biological aerated filters, one employed the surface wettability modified poly （sulfone） hollow fiber membrane segment as biofilm carder and the other employed unmodified membrane segment as biofilm carder. The experimental results showed that under the conditions of influent flux 5 L/h, hydraulic retention time 9 h and gas to liquid ratio （G/L） 10： 1, the removal rates of chemical oxygen demand （COD） and ammonium nitrogen （NH4^＋-N） for the modified packing filter and the unmodified packing filter was averaged at 83.64% and 96.25%, respectively, with the former filter being 5%-20% more than the latter. The effluent concentration of COD, NH4^＋-N and turbidity for the modified packing filter was 25.25 mg/L, 2 mg/L and 8 NTU, respectively. Moreover, the ammonium nitrogen removal performance of the filter packing the modified PSF was compared with the other bioreactor packing of an efficient floating medium. The biomass test indicated that the modified membrane matrixes provided better specific adhesion （3310-5653 mg TSS/L support）, which gave a mean of 1000 mg TSS/L more than the unmodified membrane did. In addition, the phenomenon of simultaneous denitrification on the inner surface of the support and nitrification on the outer surface was found in this work.