Hazard property classification of waste according to the recent propositions of the EC using different methods

Hazard classification of waste is a necessity, but the hazard properties (named “H” and soon “HP”) are still not all defined in a practical and operational manner at EU level. Following discussion of subsequent draft proposals from the Commission there is still no final decision. Methods to implement the proposals have recently been proposed: tests methods for physical risks, test batteries for aquatic and terrestrial ecotoxicity, an analytical package for exhaustive determination of organic substances and mineral elements, surrogate methods for the speciation of mineral elements in mineral substances in waste, and calculation methods for human toxicity and ecotoxicity with M factors.In this paper the different proposed methods have been applied to a large assortment of solid and liquid wastes (>1 0 0).Data for 45 wastes – documented with extensive chemical analysis and flammability test – were assessed in terms of the different HP criteria and results were compared to LoW for lack of an independent classification. For most waste streams the classification matches with the designation provided in the LoW. This indicates that the criteria used by LoW are similar to the HP limit values.This data set showed HP 14 ‘Ecotoxic chronic’ is the most discriminating HP. All wastes classified as acute ecotoxic are also chronic ecotoxic and the assessment of acute ecotoxicity separately is therefore not needed. The high number of HP 14 classified wastes is due to the very low limit values when stringent M factors are applied to total concentrations (worst case method). With M factor set to 1 the classification method is not sufficiently discriminating between hazardous and non-hazardous materials. The second most frequent hazard is HP 7 ‘Carcinogenic’. The third most frequent hazard is HP 10 ‘Toxic for reproduction’ and the fourth most frequent hazard is HP 4 “Irritant – skin irritation and eye damage”. In a stepwise approach, it seems relevant to assess HP 14 first, then, if the waste is not classified as hazardous, to assess subsequently HP 7, HP 10 and HP 4, and then if still not classified as hazardous, to assess the remaining properties.The elements triggering the HP 14 classification in order of importance are Zn, Cu, Pb, Cr, Cd and Hg. Progress in the speciation of Zn and Cu is essential for HP 14. Organics were quantified by the proposed method (AFNOR XP X30-489) and need no speciation. Organics can contribute significantly to intrinsic toxicity in many waste materials, but they are only of minor importance for the assessment of HP 14 as the metal concentrations are the main HP 14 classifiers. Organic compounds are however responsible for other toxicological characteristics (hormone disturbance, genotoxicity, reprotoxicity…) and shall be taken into account when the waste is not HP 14 classified.     

典型钢铁企业汞排放水平及排放特征研究

以某典型钢铁企业为研究对象,测定企业废气、废水、固废汞排放水平,并分析汞排放特征。研究表明,球团、烧结、高炉工艺废气排口烟尘中汞排放浓度和排放速率明显低于烟气;汞主要以气态形式排放,烧结工艺排口废气汞最高浓度分别是其他2个排口的7倍和3倍。球团、烧结、高炉、电炉四工艺环节中,烧结汞排放速率占四工艺汞排放速率总和的87%。半干法脱硫、氨法脱硫、石灰石石膏脱硫对废气中汞的去除效率分别为90.0%、78.7%和29.9%。企业废水排放未检出汞,脱硫产生固废汞含量明显高于除尘产生固废汞含量,脱硫灰汞含量是脱硫石膏的15倍。     

Recycling-oriented characterization of plastic frames and printed circuit boards from mobile phones by electronic and chemical imaging

This study characterizes the composition of plastic frames and printed circuit boards from end-of-life mobile phones. This knowledge may help define an optimal processing strategy for using these items as potential raw materials. Correct handling of such a waste is essential for its further “sustainable” recovery, especially to maximize the extraction of base, rare and precious metals, minimizing the environmental impact of the entire process chain. A combination of electronic and chemical imaging techniques was thus examined, applied and critically evaluated in order to optimize the processing, through the identification and the topological assessment of the materials of interest and their quantitative distribution. To reach this goal, end-of-life mobile phone derived wastes have been systematically characterized adopting both “traditional” (e.g. scanning electronic microscopy combined with microanalysis and Raman spectroscopy) and innovative (e.g. hyperspectral imaging in short wave infrared field) techniques, with reference to frames and printed circuit boards. Results showed as the combination of both the approaches (i.e. traditional and classical) could dramatically improve recycling strategies set up, as well as final products recovery.     

HACH氨氮水质自动监测分析仪进口试剂国产化配方研究

分析HACH氨氮自动监测分析仪所用进口试剂配方中氧化剂、显色剂、催化剂、掩蔽剂、缓冲液的组分、试剂用量、反应机理、吸收光谱、酸碱度、发色时间和温度、显色产物的稳定性、灵敏度、干扰及消除,以及存放条件的差异,自行研发国产配方,并将该国产配方试剂与进口试剂做试验比对,结果 2种试剂的效能无显著差异。     

Mechanical and toxicological evaluation of concrete artifacts containing waste foundry sand

The creation of metal parts via casting uses molds that are generally made from sand and phenolic resin. The waste generated after the casting process is called waste foundry sand (WFS). Depending on the mold composition and the casting process, WFS can contain substances that prevent its direct emission to the environment. In Brazil, this waste is classified according to the Standard ABNT NBR 10004:2004 as a waste Class II (Non-Inert). The recycling of this waste is limited because its characteristics change significantly after use. Although the use (or reuse) of this byproduct in civil construction is a technically feasible alternative, its effects must be evaluated, especially from mechanical and environmental points of view. Thus, the objective of this study is to investigate the effect of the use of WFS in the manufacture of cement artifacts, such as masonry blocks for walls, structural masonry blocks, and paving blocks. Blocks containing different concentrations of WFS (up to 75% by weight) were produced and evaluated using compressive strength tests (35 MPa at 28 days) and toxicity tests on Daphnia magna, Allium cepa (onion root), and Eisenia foetida (earthworm). The results showed that there was not a considerable reduction in the compressive strength, with values of 35 ± 2 MPa at 28 days. The toxicity study with the material obtained from leaching did not significantly interfere with the development of D. magna and E. foetida, but the growth of the A. cepa species was reduced. The study showed that the use of this waste in the production of concrete blocks is feasible from both mechanical and environmental points of view.     

An investigation on the fuel savings potential of hybrid hydraulic refuse collection vehicles

Refuse trucks play an important role in the waste collection process. Due to their typical driving cycle, these vehicles are characterized by large fuel consumption, which strongly affects the overall waste disposal costs. Hybrid hydraulic refuse vehicles offer an interesting alternative to conventional diesel trucks, because they are able to recuperate, store and reuse braking energy. However, the expected fuel savings can vary strongly depending on the driving cycle and the operational mode. Therefore, in order to assess the possible fuel savings, a typical driving cycle was measured in a conventional vehicle run by the waste authority of the City of Stuttgart, and a dynamical model of the considered vehicle was built up. Based on the measured driving cycle and the vehicle model including the hybrid powertrain components, simulations for both the conventional and the hybrid vehicle were performed. Fuel consumption results that indicate savings of about 20% are presented and analyzed in order to evaluate the benefit of hybrid hydraulic vehicles used for refuse collection.     

Determination of specific gravity of municipal solid waste

This investigation was conducted to evaluate experimental determination of specific gravity (G_s) of municipal solid waste (MSW). Water pycnometry, typically used for testing soils was adapted for testing MSW using a large flask with 2000 mL capacity and specimens with 100–350 g masses. Tests were conducted on manufactured waste samples prepared using US waste constituent components; fresh wastes obtained prior and subsequent to compaction at an MSW landfill; and wastes obtained from various depths at the same landfill. Factors that influence specific gravity were investigated including waste particle size, compaction, and combined decomposition and stress history. The measured average specific gravities were 1.377 and 1.530 for as-prepared/uncompacted and compacted manufactured wastes, respectively; 1.072 and 1.258 for uncompacted and compacted fresh wastes, respectively; and 2.201 for old wastes. The average organic content and degree of decomposition were 77.2% and 0%, respectively for fresh wastes and 22.8% and 88.3%, respectively for old wastes. The G_s increased with decreasing particle size, compaction, and increasing waste age. For fresh wastes, reductions in particle size and compaction caused occluded intraparticle pores to be exposed and waste particles to be deformed resulting in increases in specific gravity. For old wastes, the high G_s resulted from loss of biodegradable components that have low G_s as well as potential access to previously occluded pores and deformation of particles due to both degradation processes and applied mechanical stresses. The G_s was correlated to the degree of decomposition with a linear relationship. Unlike soils, the G_s for MSW was not unique, but varied in a landfill environment due both to physical/mechanical processes and biochemical processes. Specific gravity testing is recommended to be conducted not only using representative waste composition, but also using representative compaction, stress, and degradation states.     

Liquefaction process for a hydrothermally treated waste mixture containing plastics

Most landfilled plastic waste is a mixture or is in the form of composites with incombustible wastes such as glass, metals, and ceramics. After hydrothermal treatment, including a steam-explosion process, the separation of mixed waste (MW) into organic and inorganic substances becomes easy. However, the effect of hydrothermal pretreatment on the subsequent liquefaction of organic substances from MW is not obvious. In this study, the effects on the liquefaction of polystyrene and high-density polyethylene are discussed. Moreover, optimum conditions for the liquefaction of organic substances from hydrothermally treated MW are identified. By means of this hydrothermal pretreatment, including the steam-explosion process, polystyrene and high-density polyethylene can be significantly converted to oil by liquefaction at 300°–400°C. In comparison with liquefaction of hydrothermally pretreated mixed waste (HMW) at 300°–400°C with a batch type reactor, the yield of oil increases significantly on liquefaction using a semi-batch type reactor. It is considered that the radical chain and termination reactions among the radicals from HMW were inhibited in the semi-batch type reactor. On liquefaction of HMW in a semi-batch reactor, the conversion of HMW to oil was enhanced on increasing the liquefaction temperature to 350°C and the holding time to 60 min. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

Multi-criteria evaluation technique for SFI site identification of NORMS and oil industry waste disposal – Possibilities in Kuwait

Waste generation and accumulating quantities of oil field waste are a matter of environmental concern. This study proposes the Slurry Fracture Injection (SFI) technique as an alternative waste disposal method. The slurried solids injection waste disposal method is environmentally secure and permanent, leaving no future liabilities that must be risk-evaluated or priced. An entire waste stream comprising ground solids and waste water can be injected into deep and hydraulically secure target strata with no contamination of potable water-bearing formations or formations outside the target zone that may contain resources (gas and oil). The slurry injection method can be used to clean and reclaim landfills, oil pits and granular waste dumps. This article proposes a two-tier screening method for evaluating the feasibility of this technique and the identification of suitable target zones. A stringent environmental and process control monitoring program should complement the planning and operational period to ensure environmental protection, waste containment, and regulatory HSE compliance.     

Structure and activity of thermophilic methanogenic microbial communities exposed to quaternary ammonium sanitizer

Food processing facilities often use antimicrobial quaternary ammonium compound (QAC) sanitizers to maintain cleanliness. These QACs can end up in wastewaters used as feedstock for anaerobic digestion. The aim of this study was to measure the effect of QAC contamination on biogas production and structure of microbial communities in thermophilic digester sludge. Methane production and biogas quality data were analyzed in batch anaerobic digesters containing QAC at 0, 15, 50, 100 and 150 mg/L. Increasing sanitizer concentration in the bioreactors negatively impacted methane production rate and biogas quality. Microbial community composition data was obtained through 16S rRNA gene sequencing from the QAC-contaminated sludges. Sequencing data showed no significant restructuring of the bacterial communities. However, significant restructuring was observed within the archaeal communities as QAC concentration increased. Further studies to confirm these effects on a larger scale and with a longer retention time are necessary.