Magnetic mapping of fly-ash pollution and heavy metals from soil samples around a point source in a dry tropical environment

The Singrauli region in the southeastern part of Uttar Pradesh, India is one of the most polluted industrial sites of Asia. It encompasses 11 open cast coalmines and six thermal power stations that generate about 7,500 MW (about 10% of India’s installed generation capacity) electricity. Thermal power plants represent the main source of pollution in this region, emitting six million tonnes of fly-ash per annum. Fly-ash is deposited on soils over a large area surrounding thermal power plants. Fly-ashes have high surface concentrations of several toxic elements (heavy metals) and high atmospheric mobility. Fly ash is produced through high-temperature combustion of fossil fuel rich in ferromagnetic minerals. These contaminants can be identified using rock-magnetic methods. Magnetic susceptibility is directly linked to the concentration of ferromagnetic minerals, primarily high values of magnetite. In this study, magnetic susceptibility of top soil samples collected from surrounding areas of a bituminous-coal-fired power plant were measured to identify areas of high emission levels and to chart the spatial distribution of airborne solid particles. Sites close to the power plant have shown higher values of susceptibility that decreases with increasing distance from the source. A significant correlation between magnetic susceptibility and heavy metal content in soils is found. A comparison of the spatial distribution of magnetic susceptibility with heavy-metal concentrations in soil samples suggests that magnetic measurements can be used as a rapid and inexpensive method for proxy mapping of air borne pollution due to industrial activity.     

氨基改性生物炭负载纳米零价铁去除水中Cr(VI)

以聚乙烯亚胺（PEI）为功能单体,玉米秸秆生物炭为载体,制备了氨基改性生物炭负载型纳米零价铁（nZVI@PEI-HBC）,并利用扫描电镜（SEM）、红外光谱（FTIR）和X射线光电子能谱（XPS）等手段对材料进行了表征,分析了溶液pH、温度、材料投加量等因素对其去除Cr（VI）的影响及其去除机理.结果表明：在投加量为0.5 g·L^-1,温度为20℃,pH值为5,Cr（VI）初始浓度为20 mg·L^-1条件下,各材料对Cr（VI）的去除率大小为nZVI@PEI-HBC > nZVI > PEI-HBC > HBC.SEM显示nZVI颗粒较均匀地分散在生物炭表面,FTIR分析表明PEI改性后材料表面增加了氨基等重金属配位基团,这可能是nZVI@PEI-HBC去除Cr（VI）效果更好的原因.影响因素研究表明,材料具有较好稳定性,老化28 d后其Cr（VI）去除性能变化不大;酸性环境、升温、增大材料投加量均有利于nZVI@PEI-HBC对Cr（VI）的去除.机理研究发现,水中溶解氧加速了nZVI的腐蚀和Fe（II）的释放,促进Cr（VI）还原为Cr（III）,然后通过共沉淀作用和氨基等基团的吸附作用被去除.     

AMD铁絮体改性生物炭对重金属吸附机理研究 ——以Pb(II)为例

以酸性矿山废水生成的铁絮体和秸秆生物炭为原料,采用化学改性和紫外辐射联用技术制备改性生物炭,并通过正交试验确定最佳改性条件,同时利用FTIR、SEM和BET等方法对吸附材料的形貌特征、孔隙结构及其表面化学性质进行表征.结果表明,通过改性使吸附材料比表面积增大,吸附位点增多,在25℃、pH为7时,吸附材料改性后比表面积为295.71 m²·g^-1,对Pb（II）的拟合吸附量可达278 mg·g^-1.改性材料对Pb（II）的吸附过程符合Langmuir吸附等温线模型和准二级动力学模型,主要为单分子层吸附,受化学吸附控制.     

裂解温度和离子强度对不同来源生物炭胶体释放行为的影响

近年来环境中生物炭胶体形成受到广泛关注,它是生物炭在环境中物理分解作用的重要过程,对污染物迁移有着重要影响.然而,目前对生物炭胶体释放过程和影响因素的研究甚少,人们对生物炭胶体释放机理的认识还很有限.本研究以小麦秸秆和花生壳为生物质来源,系统地探讨了生物炭的裂解温度（300~700 ℃）和溶液离子强度（0.1~10 mmol·L^-1）对生物炭胶体产率的影响.结果表明,随着裂解温度的升高,生物炭的耐磨性增强,且在较高的裂解温度下（≥500 ℃）花生壳生物炭的耐磨性显著强于小麦秸秆生物炭.生物炭的胶体产率受到生物质来源和裂解温度的显著影响,花生壳生物炭的胶体产率低于小麦秸秆生物炭,高温裂解（≥600 ℃）生物炭的胶体产率显著低于中低温裂解生物炭.在相同溶液离子强度下,生物炭胶体产率与其亚微米级碎片率呈显著正相关（p<0.05）,即生物炭中亚微米级碎片率越高,生物炭胶体产率越高.当溶液离子强度从1 mmol·L^-1增加到10 mmol·L^-1时,两种来源生物炭的胶体产率均显著降低,其降低的程度因生物炭裂解温度而异,其中低温裂解（300 ℃）生物炭的胶体产率降低了11.1%~11.2%,中高温裂解（≥ 500 ℃）生物炭的胶体产率降低了60.0%~97.2%.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Removal and desorption of chromium in synthetic effluent by a mixed culture in a bioreactor with a magnetic field

Two chromium removal experiments were performed in bioreactors with and without a magnetic field under the same conditions.The release of the chromium present in the biomass was tested in two experiments one with the initial pH of the medium and one with pH 4.0.The objective was to remove Cr(Ⅵ) and total Cr from the effluent,this was carried out by placing biological treatments of synthetic effluent contaminated with 100 mg/L of Cr(Ⅵ) in a bioreactor with neodymium magnets that applied a magnetic field(intensity85.4 mT) to the mixed culture.The removal of Cr(Ⅵ) was approximately 100.0% for the bioreactor with a magnetic field and 93,3% for the bioreactor without a magnetic field for9 hr of recirculation of the synthetic effluent by the bioreactor.The removal of total Cr was61.6% and 48.4%,with and without a magnetic field,respectively;for 24 hr.The desorption of Cr(VI) in the synthetic effluent was 0.05 mg/L,which is below the limit established by Brazilian legislation(0.1 mg/L) for the discharge of effluent containing Cr(Ⅵ) into bodies of water.The results obtained for the removal of chromium in synthetic effluent suggested that there was no significant influence on the viable cell count of the mixed culture.The desorption of Cr(Ⅵ) in synthetic effluent after bioadsorption of chromium by the mixed culture in the process of removal of chromium in bioreactors with and without a magnetic field was not significant in either of the experiments with different initial pHs.     

水稻秸秆生物炭中铜和镉的形态分布及释放特性

由于目前缺乏对生物质原料来源的管控办法,极有可能用产自受污染农田土壤的秸秆制备出具有高重金属含量的生物炭,因此,研究生物炭中重金属的形态分布及其释放特性对于防控生物炭应用产生的环境风险具有重要意义.基于此,分别采集江西省贵溪铜冶炼厂周边九牛岗污染区和中国科学院鹰潭红壤生态实验站清洁区种植的水稻秸秆制备生物炭（分别记为“九牛岗生物炭”和“红壤站生物炭”）,分析两种生物炭中Cu、Cd的含量及其化学形态分布,考察不同固液比及pH对生物炭中Cu、Cd浸出的影响.结果表明:九牛岗生物炭中Cu、Cd的总量（以w计）分别为119.99、3.83 mg/kg,显著高于红壤站生物炭（19.50、0.96 mg/kg）.尽管九牛岗生物炭中w（酸溶态Cu）、w（酸溶态Cd）显著高于红壤站生物炭,但在形态分布上,九牛岗生物炭中Cu、Cd主要为相对稳定态（可氧化态和残渣态）,二者占比分别为80.3%、76.7%,高于红壤站生物炭（二者占比分别为53.2%、48.0%）.高固液比和低pH可有效增加两种生物炭中Cu、Cd的浸出毒性,其中,九牛岗生物炭在固液比为1:20和1:60时,浸出液中ρ（Cu）、ρ（Cd）均超过GB/T 14848—2017《地下水质量标准》中Ⅱ类标准限值.动力学及累积释放试验表明,两种生物炭中的部分Cu、Cd可在短时间内迅速释放而后逐渐平稳并有上升趋势,且九牛岗生物炭中Cu、Cd释放量显著高于红壤站生物炭.研究显示,来自污染区水稻秸秆生物炭中的Cu、Cd活性显著高于清洁区生物炭,具有更高的环境风险.      

生物炭复合青霉菌修复砷污染土壤对其微生物群落功能多样性的影响

真菌修复砷污染土壤是一种能够有效吸附固化环境中砷的重要措施.生物炭作为目前修复重金属的热点,其多空疏松的结构、较高的离子交换量、丰富的有机碳含量等都说明了其在土壤修复中的地位.为了探究生物炭与青霉菌在修复砷污染土壤的同时对土壤中微生物活性及其多样性的影响,在室内孵育条件下,运用Biolog法研究了3×3随机区组试验（3个生物炭梯度分别为0%、2%、4%,3个青霉菌梯度分别为0%、10%、20%）下土壤微生物对不同类型碳源的利用能力以及多种功能性指数的影响.结果表明:①添加青霉菌与生物炭后,土壤中有效砷含量较对照组显著下降,从而影响其微生物群落功能多样性.②砷污染土壤中微生物群落功能多样性、碳源利用丰富度随生物炭浓度梯度的升高呈先升后降的趋势.③高接菌量（20%）与低接菌量（10%）对砷污染土壤中微生物群落功能多样性的影响没有显著性差异.④2%生物炭与10%青霉菌处理土壤中微生物群落功能多样性、碳源利用丰度最高.⑤青霉菌对胺类及少部分酸类碳源的利用能力较弱（AWCD < 0.5,AWCD为Biolog微平板孔中溶液吸光值平均颜色变化率）,对氨基酸类中大部分碳源以及脂类碳源的代谢能力较强（AWCD>1.0）,对糖类、酚酸类的代谢能力稍弱（AWCD为0.3~1.0）,青霉菌对D-半乳糖醛酸、L-天冬酰胺酸、L-丝氨酸、L-精氨酸、r-羟基丁酸这5种碳源的利用率最高（AWCD>1.2）.研究显示,低浓度生物炭可增加砷污染土壤中微生物群落多样性,生物炭含量的继续增加会对微生物产生抑制作用;青霉菌添加到砷污染土壤后,会显著提升砷污染土壤中微生物的群落功能多样性,改善砷污染土壤中微生的物群落结构;青霉菌的优势碳源大多为植物根系分泌物,可为后续青霉菌与超积累植物复合修复砷污染土壤提供参考.      

不同基质生物炭对厌氧处理餐厨垃圾效能及微生态的影响

探究了剩余污泥（SS）、餐厨垃圾（FW）、玉米芯（CC）、甘蔗渣（BG）4种不同基质生物炭对厌氧生物处理餐厨垃圾效能的影响,对厌氧污泥的关键酶活性、微生物群落分布以及代谢途径等微生态进行了分析.结果表明,厌氧反应器分别加入4种生物炭后,COD平均去除率分别提高了29.49%、23.16%、29.42%、40.32%;傅里叶红外分析表明,投加SS生物炭组出水中羟基、酰胺基以及C-O-C伸缩振动峰减弱.4个厌氧反应器中厌氧污泥的乙酸激酶活性分别为0.40,0.42,0.96,0.98 μmol/g,表明投加CC与BG生物炭促进了餐厨垃圾的厌氧水解酸化过程;厌氧污泥胞外聚合物的蛋白质/多糖之比分别为0.415、0.56、1.89、2.8,投加CC、BG生物炭提高了污泥的稳定性.4个厌氧反应器中拟杆菌门、变形菌门、厚壁菌门为主要菌群,投加BG生物炭促进了变形菌门与厚壁菌门的生长;对于古细菌而言,甲烷杆菌属与甲烷丝菌属为优势种群,SS组的甲烷杆菌属丰度最高（53.48%）,而BG组中甲烷丝菌属丰度最高（42.72%）.KEGG功能分析表明古菌及细菌均以碳水化合物代谢、氨基酸代谢为主;而投加BG与SS生物炭后,微生物膜运输水平得到了提高.     

不同裂解温度稻壳生物炭对阿特拉津的吸附行为及机制

为探究不同裂解温度下稻壳生物炭的结构和性质差异及其对阿特拉津（AT）的吸附作用机制和构-效关系,以稻壳为原料在300、500和700℃下制备稻壳生物炭（分别记为RH300、RH500、RH700）,通过电镜扫描、元素分析仪、比表面积分析仪和傅里叶变换红外光谱分析仪等对3种稻壳生物炭进行结构表征分析,并采用批量等温吸附法研究稻壳生物炭对AT的吸附特性.结果表明:裂解温度由300℃升至700℃时,稻壳生物炭中w（C）由48.81%升至64.67%,w（H）、w（N）和w（O）则由3.22%、1.45%和34.66%分别降至0.89%、0.92%和16.29%,原子比H/C、O/C和（O+N）/C值均降低.可见,随着裂解温度升高,稻壳生物炭的芳香性增强,亲水性和极性降低,且比表面积和孔体积增大,平均孔径减小.3种稻壳生物炭对AT的吸附均可用Freundlich和Langmuir两种等温吸附模型进行较好地拟合（R≥0.948,P < 0.01）,吸附作用及非线性程度与生物炭的比表面积（SSA）、芳香性（H/C）、亲水性（O/C）和极性〔（O+N）/C〕呈良好的指数关系,大小表现为RH700 > RH500 > RH300.稻壳生物炭对AT的吸附机制主要包括分配作用和表面吸附,分配作用强度与生物炭的极性和炭化程度有关;而表面吸附作用与AT的分子大小有关,3种稻壳生物炭对AT的表面吸附除表面覆盖外,还存在多层平铺、毛细管现象和孔隙填充等.研究显示,裂解温度是影响生物炭吸附有机污染物的重要因素,在综合考虑成本和制备工艺的同时,适当提高裂解温度可增强生物炭对有机污染物的吸附作用.