厌氧—好氧—生物炭系统处理印染废水实例

阐述了采用厌氧水解－好氧生物接触－生物炭吸附氧化工艺处理印染废水的工艺流程、原理、工艺参数及特点。该系统对印染废水ＣＯＤｃｒ及色度的处理取得良好效果，且污泥量少，节省了污泥处理费用。     

山西矿区矸石山复垦种植施肥策略

围绕煤矸石缺乏有机活性物质及有效养分的问题，在矸石山复垦种植时，对施肥作了试验研究。结果表明，煤矸石风化物由于吸附性能低，保肥性差，所以施用化肥时一次用量不宜过大。并从降低复垦的投资与难度以及尽快建立一个可自我维持生长的植被出发，提出了矸石山复垦种植时化肥与污泥配合施用的施肥策略，并对污泥的施用效果做了研究。     

Petroleum waste biodegradation with porous biomass support system (PBSS) on rotating biological contactor

A laboratory scale study was conducted to assess the feasibility of the new coupling of rotating biological contactor (RBC) plus porous biomass support system (PBSS) using polyurethane foam as porous support media to biodegrade petroleum refinery wastewater. Polyurethane foam was attached on disks of two four-stage laboratory scale cascade connected RBC units.The two RBC units were operated simultaneously at different but constant, flowrates giving hydraulic loading rates of 0.01, 0.02, 0.03, 0.04 m3/m2/d in two runs keeping the same rotational speed 10 r/min throughout. Organic loading was a less controllable factor in this study.For all of the hydraulic loadings, it was found that the removal efficiency of total chemical oxygen demand (TCOD) and oil were above 80 percent. Ammonia nitrogen and phenol removal were above 90 and 80 percent respectively. The maximum biomass concentration within polyurethane foam was about 30 g/m2 in the first stage for 0.03 m3/m2/d hydraulic loading.The results show that t     

中度污染水资源用于电厂循环冷却系统工艺研究

采用曝气生物滤池与高效混凝沉淀工艺对城市污水厂二级处理出水进行了2 m3/h规模的中试研究,并在此基础上对被污染的地表水进行了600m3/h规模的工程试验研究。研究表明,中度污染水资源通过这一工艺处理,可以满足电厂循环冷却水补给水的水质要求,并可以取得较高的处理效率。工程试验证实,此工艺运行稳定,系统易启动,抗冲击能力强,管理方便,具有推广应用的价值。     

曝气生物滤池Biostyr处理微污染水源

采用曝气生物滤池Biostyr对浙江省T市某水厂微污染水源水进行生物预处理,现场试验研究表明:在气水比为2∶1,滤速6m/h,水温24～32℃的运行条件下,其对水中各污染物的平均去除率为:高锰酸盐指数24.1%,氨氮81.7%,亚硝酸盐氮79.9%,浊度49.0%。完全能达到生物预处理目的。     

微污染饮用水生物过滤影响因素的研究

通过试验探讨了过滤介质、空床接触时间、水温和反冲洗方式对生物过滤去除有机物的影响。试验结果表明 :活性炭、石英砂组成的双层滤料生物滤池对高锰酸盐指数、UV2 5 4的去除效果比无烟煤、石英砂组成的双层滤料滤池和单层石英砂滤料滤池好 ;在一定的范围内 ,随着接触时间或水温的增加 ,各滤柱对高锰酸盐指数的去除率增加 ;加氯水反冲洗方式对生物滤池去除高锰酸盐指数、UV2 5 4的影响比未加氯水反冲洗方式大     

生物膜MBR反应器和MBR反应器处理洗涤废水比较

比较生物膜MBR反应器和MBR反应器处理洗涤废水的效果。结果表明,两个系统对COD、LAS及氨氮的去除均具有良好的处理效果。和MBR反应器相比,生物膜MBR反应器的运行条件要好。生物膜MBR反应器的运行条件:水力停留时间(HRT)4～4.5h,气水比351∶,而MBR反应器的运行条件:水力停留时间(HRT)9～10h,气水比451∶。通过两个反应器抗冲击负荷实验的研究,结果表明,在进水水质相同的条件下,就膜生物反应器的上清液而言,生物膜MBR反应器具有更好的抗冲击负荷能力。     

AF+BAF深度处理PCB生产废水的试验研究

针对PCB废水难降解及含重金属铜的特点,在经过一系列的物化处理的基础上,采用AF+BAF组合工艺对其进行深度处理。试验研究中,通过控制污水在反应器中的停留时间,使得废水在AF中水解酸化,以增加废水的可生化性,在此基础上利用BAF的生物膜来去除污水中剩余的有机物。试验结果表明,试验系统对PCB废水中的COD、Cu2+去除效果良好,出水COD、Cu2+的含量分别稳定在10~50mg/L和0.02~0.1mg/L,达到排放标准。     

Treatment of 2-phenylamino-3-methyl-6-di-n-butylaminofluoran production effluent by combination of biological treatments and Fenton＇s oxidation

High strength refractory organic stream is produced during the production of 2-phenylamino-3-methyl-6-di-n-butylaminofluoran （One Dye Black 2, abbr. ODB 2）, a novel heat-sensitive material with a promising market. In this study, a combination of acidificationprecipitation, primary biological treatment, Fenton＇s oxidation and another biological treatment was successfully used for the removal of COD from 18000-25000 mg/L to below 200 mg/L from the ODB 2 production wastewater in a pilot experiment. A COD removal of 70%-80% was achieved by acidification-precipitation under a pH of 2.5-3.0. The first step biodegradafion permitted an average COD removal of 70% under an hydraulic residence time （HRT） of 30 h. By batch tests, the optimum conditions of Fenton＇s oxidation were acquired as： Fe^2＋ dose 6.0 mmol/L; H2O2 dose 3000 mg/L; and reaction time 6 h. The second step biological treatment could ensure an effluent COD below 200 mg/L under an HRT of 10 h following the Fenton＇s treatment.     

皮革和毛皮加工废水处理技术

采用混凝沉淀-酸化水解-悬挂链曝气-生物接触氧化组合工艺处理皮革和毛皮加工生产废水。实验结果表明;进水COD为2400mg/L,处理后出水COD≤100mg/L,去除率≥95.8%。各项水质指标均稳定地达到了GB8978-96污水综合排放一级标准。