Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

印铁涂装烘房有机废气的直接燃烧法处理实践

本文通过采用催化法和直燃法两种工艺处理印铁涂装生产的有机废气的工业实践,对设计和运行中的一些要点进行分析和探讨。     

大气中SO2的液相氧化研究

大气中ＳＯ２液相氧化是形成酸雨的重要途径，降雨中含有各种无机离子和有机物质，它们可能催化或抑制液相氧化反应的进行。本文根据四川酸雨样品组成，进行了ＳＯ２在模拟雨水及实际雨水中的氧化实验，考查了Ｖ，Ｆｅ，Ｍｎ等离子对ＳＯ２氧化的催化作用，Ｈ２Ｏ２对ＳＯ２的氧化以及降水中有机物质甲醛对各反应的影响。实验结果为了解酸雨的成固，研究酸雨控制对策提供了科学依据。     

催化裂化废水萃取脱酚预处理研究

选用焦化粗柴油为萃取剂,对催化裂化含酚废水进行脱酚预处理,结果表明,最佳萃取条件为：ｐＨ７．０－８．５,温度１５－４０℃,油水体系比１．７－２．１,理论萃取级数４－７级。在上述条件下,出水酚质量浓度为５０ｍｇ／Ｌ。萃取后的粗柴油用于炼油厂加氢精制装置。     

溶胶凝胶法制备铜催化剂及其稳定性的研究

介绍了利用溶胶凝胶方法制备铜系催化剂，并考察了制备过程中各个工艺参数对铜系催化剂稳定性的影响。通过优化催化剂的设计和制备方法，可有效地改善Cu^2＋的溶出问题，使该类催化剂具有广阔的应用前景。     

污染治理中的微波诱导催化技术

归纳了微波诱导催化技术在大气羡染控制、水污染控制、固体废弃物处理与处置等污染治理中的应用状况及应用实例，阐述了微波诱导催化技术的基本原理，提出了微波诱导催化技术在实践应用环节中存在的问题及解决措施，展望了微波诱导催化技术在污染治理领域中的应用前景。     

催化湿式氧化法处理吡虫啉农药废水

自制了Cu／Mn，Cu／Ce，Cu／Ni，Ce／Mn，Ce／Ag等催化剂，经过性能比较，选择催化活性较高且金属溶出量较小的Cu／Ni作催化剂。用催化湿式氧化法处理吡虫啉农药废水，考察了各种因素对处理效果的影响。实验结果表明：在进水pH为6．93、Cu／Ni加入量为4．0g、反应温度为190oC、氧分压为1．6MPa、反应时间为120min的条件下，COD去除率为95％；处理后废水的BOD5／COD从0．093增至0．590，可生化性明显改善。     

催化还原SO2为单质硫技术的研究进展

催化还原法脱硫是一种能够直接回收单质硫的烟气脱硫(FGD)技术,近年来倍受关注.尽管催化还原法脱硫技术所采用的催化剂的种类繁多,但是该技术所采用的还原剂的种类却相对较少.以H2、C、CH4、NH3和CO 5种还原剂为分类标准,综述了催化还原SO2为单质硫技术的主要研究成果;讨论了相关催化剂的性质和催化反应机理;分析了不同还原脱硫技术的优缺点.最后,论述了催化还原法脱硫有待解决的关键问题与发展趋势.     

矾土尾矿载体双活性组分甲苯催化燃烧催化性能研究

利用矾土尾矿制备催化剂载体,采用浸渍法将双活性组分氧化物载于催化剂载体,研究甲苯催化燃烧性能.结果表明,当Cu、Mn物质的量比为1∶2、负载量为14％、焙烧温度为500℃、焙烧2h时CuMn/ZrO2整体催化剂催化活性高,起燃温度为210℃,完全燃烧温度为230℃,有效降低了甲苯催化燃烧的起燃温度和完全燃烧温度.     

Occurrence and migration of microplastics and plasticizers in different wastewater and sludge treatment units in municipal wastewater treatment plant

● Reduce the quantifying MPs time by using Nile red staining. ● The removal rate of MPs and PAEs in wastewater and sludge were investigated. ● MPs and PAEs were firstly analyzed during thermal hydrolysis treatment. ● The removal of PAEs from wastewater and sludge was mainly biodegradation. Microplastics (MPs) and plasticizers, such as phthalate esters (PAEs), were frequently detected in municipal wastewater treatment plants (MWTP). Previous research mainly studied the removal of MPs and PAEs in wastewater. However, the occurrence of MPs and PAEs in the sludge was generally ignored. To comprehensively investigate the occurrence and the migration behaviors of MPs and PAEs in MWTP, a series of representative parameters including the number, size, color, shape of MPs, and the concentrations of PAEs in wastewater and sludge were systematically investigated. In this study, the concentrations of MPs in the influent and effluent were 15.46±0.37 and 0.30±0.14 particles/L. The MP removal efficiency of 98.1% was achieved and about 73.8% of MPs were accumulated in the sludge in the MWTP. The numbers of MPs in the sludge before and after digestion were 4.40±0.14 and 0.31±0.01 particles/g (dry sludge), respectively. Fourier Transform Infrared Spectroscopy (ATR FT-IR) analysis showed that the main types of MPs were polyethylene terephthalate (PET), polypropylene (PP), polyethylene (PE), and polystyrene (PS). Six PAEs, including phthalate (DMP), diethyl phthalate (DEP), diisobutyl phthalate (DIBP), ortho dibutyl phthalate (DBP), butyl benzyl phthalate (BBP), and bis(2-ethyl) hexyl phthalate (DEHP), were detected in the MWTP. The concentrations of total PAEs (ΣPAEs) in the influent and effluent were 76.66 and 6.28 µg/L, respectively. The concentrations of ΣPAEs in the sludge before and after digestion were 152.64 and 31.70 µg/g, respectively. In the process of thermal hydrolysis, the number and size of MPs decreased accompanied by the increase of the plasticizer concentration.